Efficiency of safety measures applied to a manual knapsack sprayer for paraquat application to Maize (Zea mays L.)

The objectives of the present study were to evaluate the safety of mixer/loaders and applicators of paraquat to maize crop by knapsack sprayers and to determine the efficacy of safety measures applied to the sprayers. Potential dermal exposure (PDE) was evaluated in 22 worker body parts. The Cu2+ cation of a copper-based fungicide was used as tracer in the spray solution. Sanitary pads and cotton gloves were used to collect the pesticide solution on the sampled body parts. It was observed that paraquat application in front of the applicator's body (0.5 and 1.0 m lance) is unsafe because PDE was 1,979.8 ml/day (for 0.5 m lance) and 1,290.4 ml/day (for 1.0 m lance) and needs 50-80% and 37-69% control of PDE respectively. Control can be achieved by the use of protective garment on the legs and feet only, which received 92-93% of the PDE. Switching the spray nozzle to the back of the operator reduced the PDE by 98% and was sufficient to make working conditions safe, while maintaining the efficiency of application and making the work lighter and more comfortable. Mixer/loaders received 86% of the PDE to the hands and the work condition was safe (MOS > 1), however impermeable gloves could be used as a further safety measure.

A comparison of the performance and biological efficiency of new knapsack sprayers and a controlled droplet application (CDA) sprayer for the control of the diamondback moth, Plutella xylostella L. (Lepidoptera : Plutellidae)

Field trials and laboratory bioassays were undertaken to compare the performance and efficacy (mortality of diamondback moth larvae) of insecticides applied to cabbages with three high volume hydraulic knapsack sprayers (NS-16, PB-20 and Selecta 12V) and a controlled droplet application (CDA) sprayer. In field experiments, the high volume knapsack sprayers (application rate 500-600 L ha(-1)) provided better spray coverage on the upper and lower surfaces of inner leaves, the upper surfaces of middle and outer leaves, and greater biological efficacy than the CDA sprayer (application rate 20similar to40 L ha(-1)). The PB-20 provided better spray coverage on the upper surface of middle leaves and both surfaces of outer leaves when compared with the Selecta 12V. However, its biological efficacy in the field was not significantly different from that of the other high volume sprayers. Increasing the application rate from 20 to 40 L ha(-1) for the CDA sprayer significantly increased droplet density but had no impact on test insect mortality. Laboratory evaluations of biological efficacy yielded higher estimates than field evaluations and there was no significant difference between the performance of the PB-20 and the CDA sprayer. Significant positive relationships were detected between insect mortality and droplet density deposited for both the PB-20 and the CDA sprayers.

Avaliação de volumes de calda proporcionados por diferentes pontas de pulverização no controle de Tuta absoluta (Meirick, 1917) (Lepidoptera: Gelechiidae) em tomate rasteiro

O objetivo deste trabalho foi avaliar o controle da traça-do-tomateiro em função dos volumes de aplicação. O levantamento da infestação da praga foi realizado avaliando-se o número de lagartas e de lesões com e sem lagarta viva e o número de ovos em folhas e frutos. Os tratamentos realizados foram o inseticida chlorfluazuron na dosagem de 80 mL p.c. 100 L-1, aplicado com as pontas: TJ6011002, TJ6011004, TX04VK e TX12VK cada uma utilizando, respectivamente, o volume de calda de: 200, 600, 200 e 600 L ha-1; e o pulverizador costal motorizado (100 L ha-1); todos com e sem o adjuvante polioxietileno alquil fenol éter (1 mL 10 L-1 de água) e mais uma testemunha. Verificou-se que os tratamentos com e sem adjuvantes não diferiram entre si. Porém, houve diferença entre os volumes utilizados, sendo menor a ocorrência de lesões nas parcelas tratadas com o volume de 600 L ha-1 . Houve também diferença em relação ao uso do adjuvante para o volume de 200 L ha-1 , sendo que o número de ovos foi superior sem a sua utilização. Neste trabalho, foi observada a importância do monitoramento no controle de pragas.

Efeito de inseticidas , superfícies tratadas e período de exposição em duas populações de Blattella germanica (Linnaeus, 1767) (Blattodea: Blattellidae)

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Redução na dosagem da mistura (fluazifop-p-butil+fomesafen) em dois cultivares de soja e em três épocas de semeadura

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Procedures to Evaluate the Efficiency of Protective Clothing Worn by Operators Applying Pesticide

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Eficácia de óleos minerais aplicados como adjuvantes auxiliando na selitividade de herbicidas na cultura de cana-de-açúcar

Pós-graduação em Agronomia - FEIS

Solving large 0–1 multidimensional knapsack problems by a new simplified binary artificial fish swarm algorithm

The artificial fish swarm algorithm has recently been emerged in continuous global optimization. It uses points of a population in space to identify the position of fish in the school. Many real-world optimization problems are described by 0-1 multidimensional knapsack problems that are NP-hard. In the last decades several exact as well as heuristic methods have been proposed for solving these problems. In this paper, a new simpli ed binary version of the artificial fish swarm algorithm is presented, where a point/ fish is represented by a binary string of 0/1 bits. Trial points are created by using crossover and mutation in the different fi sh behavior that are randomly selected by using two user de ned probability values. In order to make the points feasible the presented algorithm uses a random heuristic drop item procedure followed by an add item procedure aiming to increase the profit throughout the adding of more items in the knapsack. A cyclic reinitialization of 50% of the population, and a simple local search that allows the progress of a small percentage of points towards optimality and after that refines the best point in the population greatly improve the quality of the solutions. The presented method is tested on a set of benchmark instances and a comparison with other methods available in literature is shown. The comparison shows that the proposed method can be an alternative method for solving these problems.

Aplicació web de generació i autoavaluació d'exàmens tipus test basat en el criptosistema knapsack

Creació d'una aplicació web que genera exàmens tipus test agafant les preguntes d'un banc de preguntes. Genera una versió per cada alumne del mateix exàmen, amb les preguntes desordenades i les opcions també desordenades. A cada resposta se li associa un número. El resultat de l'exàmen és la suma de les repostes. Mitjançant el criptosistema Knapsack ficant a l'aplicació el número resultat de l'exàmen s'obté la nota.

Microfabricated dual sprayer for on-line mass tagging of phosphopeptides.

Phosphopeptides tagging reactions by dinuclear zinc(II) complexes (1,3-bis[bis(2-pyridylmethyl)amino]-propan-2-olato dizinc(II)3+, called tag) were performed with a dual-channel microsprayer in electrospray ionization mass spectrometry. The reaction is first studied ex situ and analyzed with a commercial electrospray source. In situ reactions (i.e., inside the Taylor cone) were achieved with a dual-channel microsprayer both with the tag synthesized chemically before the experiments and with the tag electrogenerated by in situ oxidation of a zinc electrode, also used to apply the electrospray current. The device consists of a polyimide microchip with two microchannels (20 microm x 50 microm x 1 cm) etched on each side of the structure and connecting only at the tip of the microchip. We demonstrate here that mixing two solutions with different physicochemical properties inside the Taylor cone can be used to selectively tag target molecules.

Knapsack sets for cryptography

The basic goal of this study is to extend old and propose new ways to generate knapsack sets suitable for use in public key cryptography. The knapsack problem and its cryptographic use are reviewed in the introductory chapter. Terminology is based on common cryptographic vocabulary. For example, solving the knapsack problem (which is here a subset sum problem) is termed decipherment. Chapter 1 also reviews the most famous knapsack cryptosystem, the Merkle Hellman system. It is based on a superincreasing knapsack and uses modular multiplication as a trapdoor transformation. The insecurity caused by these two properties exemplifies the two general categories of attacks against knapsack systems. These categories provide the motivation for Chapters 2 and 4. Chapter 2 discusses the density of a knapsack and the dangers of having a low density. Chapter 3 interrupts for a while the more abstract treatment by showing examples of small injective knapsacks and extrapolating conjectures on some characteristics of knapsacks of larger size, especially their density and number. The most common trapdoor technique, modular multiplication, is likely to cause insecurity, but as argued in Chapter 4, it is difficult to find any other simple trapdoor techniques. This discussion also provides a basis for the introduction of various categories of non injectivity in Chapter 5. Besides general ideas of non injectivity of knapsack systems, Chapter 5 introduces and evaluates several ways to construct such systems, most notably the "exceptional blocks" in superincreasing knapsacks and the usage of "too small" a modulus in the modular multiplication as a trapdoor technique. The author believes that non injectivity is the most promising direction for development of knapsack cryptosystema. Chapter 6 modifies two well known knapsack schemes, the Merkle Hellman multiplicative trapdoor knapsack and the Graham Shamir knapsack. The main interest is in aspects other than non injectivity, although that is also exploited. In the end of the chapter, constructions proposed by Desmedt et. al. are presented to serve as a comparison for the developments of the subsequent three chapters. Chapter 7 provides a general framework for the iterative construction of injective knapsacks from smaller knapsacks, together with a simple example, the "three elements" system. In Chapters 8 and 9 the general framework is put into practice in two different ways. Modularly injective small knapsacks are used in Chapter 9 to construct a large knapsack, which is called the congruential knapsack. The addends of a subset sum can be found by decrementing the sum iteratively by using each of the small knapsacks and their moduli in turn. The construction is also generalized to the non injective case, which can lead to especially good results in the density, without complicating the deciphering process too much. Chapter 9 presents three related ways to realize the general framework of Chapter 7. The main idea is to join iteratively small knapsacks, each element of which would satisfy the superincreasing condition. As a whole, none of these systems need become superincreasing, though the development of density is not better than that. The new knapsack systems are injective but they can be deciphered with the same searching method as the non injective knapsacks with the "exceptional blocks" in Chapter 5. The final Chapter 10 first reviews the Chor Rivest knapsack system, which has withstood all cryptanalytic attacks. A couple of modifications to the use of this system are presented in order to further increase the security or make the construction easier. The latter goal is attempted by reducing the size of the Chor Rivest knapsack embedded in the modified system. '

Calibration of angles of nozzles and deposition of an axial-flow sprayer on dwarf cashew

The study aimed to determine an optimum angle for the nozzles axial-flow sprayers a deposition for better vertical distribution focused on cashew. In laboratory tests were conducted adjusting the angle of the nozzle axial-flow sprayers. The experimental design was randomized blocks in a 2x3 factorial with four replications. The treatment for this test were two settings (with and without the adjustment of the angles of the nozzles ) and tree application volumes 273, 699 and 954 L ha-¹.The study was conducted in an orchard of dwarf cashew, with eight years of age. It was concluded that the volumetric distribution profile showed better vertical distribution uniformity when the angles of the nozzles were regulated for the canopy, the adjustment of the angles of the nozzles for the canopy provided greater deposition of droplets, the increased volume of application resulted in higher depositions in the leaves of the crop.

Air flow humidification for air-assisted boom sprayer

The air-assisted ground spray is fairly widespread. However, due to the unpredictable weather conditions, the operational efficiency is impaired by stops on grounds of low humidity and high temperatures. The aim of this work was to assess an air humidification method and evaluate its impact on temperature and air humidity for the air curtain of the air-assisted sprayer. With respect to relative air humidity, it has increased in 6.59%, being the maximum change when inserting 1.92 L min-1. So, it is concluded that the pipeline humidification might significantly reduce temperature and enhance air humidity. The treatments performed in this study consisted of a varied flow of a humidity device, related to weather conditions. Temperature and relative air humidity were measured at 1.0 m height from right to left of middle point of the machine, corresponding to the end of the spray boom, in the middle and end of right spray boom. The readings were also performed at three different distances from the end of the pipeline and at 0.25 and 0.50 m from that to the soil. The results show that 0.48 L min-1 in the humidification system has promoted a better efficiency in reducing air-temperature, on average 2.52 ºC when compared to the non-humidified one.

The knapsack problem approach in solving partial hedging problems of options

En option är ett finansiellt kontrakt som ger dess innehavare en rättighet (men medför ingen skyldighet) att sälja eller köpa någonting (till exempel en aktie) till eller från säljaren av optionen till ett visst pris vid en bestämd tidpunkt i framtiden. Den som säljer optionen binder sig till att gå med på denna framtida transaktion ifall optionsinnehavaren längre fram bestämmer sig för att inlösa optionen. Säljaren av optionen åtar sig alltså en risk av att den framtida transaktion som optionsinnehavaren kan tvinga honom att göra visar sig vara ofördelaktig för honom. Frågan om hur säljaren kan skydda sig mot denna risk leder till intressanta optimeringsproblem, där målet är att hitta en optimal skyddsstrategi under vissa givna villkor. Sådana optimeringsproblem har studerats mycket inom finansiell matematik. Avhandlingen "The knapsack problem approach in solving partial hedging problems of options" inför en ytterligare synpunkt till denna diskussion: I en relativt enkel (ändlig och komplett) marknadsmodell kan nämligen vissa partiella skyddsproblem beskrivas som så kallade kappsäcksproblem. De sistnämnda är välkända inom en gren av matematik som heter operationsanalys. I avhandlingen visas hur skyddsproblem som tidigare lösts på andra sätt kan alternativt lösas med hjälp av metoder som utvecklats för kappsäcksproblem. Förfarandet tillämpas även på helt nya skyddsproblem i samband med så kallade amerikanska optioner.

Drift from the use of handheld knapsack pesticide sprayers in Boyacá (Colombian Andes)

Offsite pesticide losses in tropical mountainous regions have been little studied. One example is measuring pesticide drift soil deposition, which can support pesticide risk assessment for surface water, soil, bystanders, off target plants and fauna. This is considered a serious gap, given the evidence of pesticide-related poisoning in those regions. Empirical data of drift deposition of a pesticide surrogate, Uranine tracer, within one of the highest potato producing regions in Colombia, characterized by small plots and mountain orography, is presented. High drift values encountered in our study reflect the actual spray conditions using handled knapsack sprayers. Comparison between measured and predicted drift values using three existing empirical equations showed important underestimation. However, after their optimization based on measured drift information, the equations showed a strong predictive power for this study area and the study conditions. The most suitable curve to assess mean relative drift was the IMAG calculator after optimization.