Shock Train/Boundary-Layer Interaction in Rectangular Scramjet Isolators

Numerous studies of the dual-mode scramjet isolator, a critical component in preventing inlet unstart and/or vehicle loss by containing a collection of flow disturbances called a shock train, have been performed since the dual-mode propulsion cycle was introduced in the 1960s. Low momentum corner flow and other three-dimensional effects inherent to rectangular isolators have, however, been largely ignored in experimental studies of the boundary layer separation driven isolator shock train dynamics. Furthermore, the use of two dimensional diagnostic techniques in past works, be it single-perspective line-of-sight schlieren/shadowgraphy or single axis wall pressure measurements, have been unable to resolve the three-dimensional flow features inside the rectangular isolator. These flow characteristics need to be thoroughly understood if robust dual-mode scramjet designs are to be fielded. The work presented in this thesis is focused on experimentally analyzing shock train/boundary layer interactions from multiple perspectives in aspect ratio 1.0, 3.0, and 6.0 rectangular isolators with inflow Mach numbers ranging from 2.4 to 2.7. Secondary steady-state Computational Fluid Dynamics studies are performed to compare to the experimental results and to provide additional perspectives of the flow field. Specific issues that remain unresolved after decades of isolator shock train studies that are addressed in this work include the three-dimensional formation of the isolator shock train front, the spatial and temporal low momentum corner flow separation scales, the transient behavior of shock train/boundary layer interaction at specific coordinates along the isolator's lateral axis, and effects of the rectangular geometry on semi-empirical relations for shock train length prediction. A novel multiplane shadowgraph technique is developed to resolve the structure of the shock train along both the minor and major duct axis simultaneously. It is shown that the shock train front is of a hybrid oblique/normal nature. Initial low momentum corner flow separation spawns the formation of oblique shock planes which interact and proceed toward the center flow region, becoming more normal in the process. The hybrid structure becomes more two-dimensional as aspect ratio is increased but corner flow separation precedes center flow separation on the order of 1 duct height for all aspect ratios considered. Additional instantaneous oil flow surface visualization shows the symmetry of the three-dimensional shock train front around the lower wall centerline. Quantitative synthetic schlieren visualization shows the density gradient magnitude approximately double between the corner oblique and center flow normal structures. Fast response pressure measurements acquired near the corner region of the duct show preliminary separation in the outer regions preceding centerline separation on the order of 2 seconds. Non-intrusive Focusing Schlieren Deflectometry Velocimeter measurements reveal that both shock train oscillation frequency and velocity component decrease as measurements are taken away from centerline and towards the side-wall region, along with confirming the more two dimensional shock train front approximation for higher aspect ratios. An updated modification to Waltrup \& Billig's original semi-empirical shock train length relation for circular ducts based on centerline pressure measurements is introduced to account for rectangular isolator aspect ratio, upstream corner separation length scale, and major- and minor-axis boundary layer momentum thickness asymmetry. The latter is derived both experimentally and computationally and it is shown that the major-axis (side-wall) boundary layer has lower momentum thickness compared to the minor-axis (nozzle bounded) boundary layer, making it more separable. Furthermore, it is shown that the updated correlation drastically improves shock train length prediction capabilities in higher aspect ratio isolators. This thesis suggests that performance analysis of rectangular confined supersonic flow fields can no longer be based on observations and measurements obtained along a single axis alone. Knowledge gained by the work performed in this study will allow for the development of more robust shock train leading edge detection techniques and isolator designs which can greatly mitigate the risk of inlet unstart and/or vehicle loss in flight.

An optically coupled power stimulus isolation unit with high voltage and fast rise time output

Recent technological developments have created new devices that could improve and simplify the construction of stimulus isolators. HEXFET transistors can switch large currents and hundreds of volts in nanoseconds. The newer opto-isolators can give a pulse rise time of a few nanoseconds, with output compatible with MOSFET devices, in which delays are reduced to nanoseconds. Integrated DC/DC converters are now available. Using these new resources we developed a new electrical stimulus isolator circuit with selectable constant-current and constant-voltage modes, which are precise and easy to construct. The circuit works like a regulated power supply in both modes with output switched to zero or to free mode through an opto-isolator device. The isolator analyses showed good practical performance. The output to ground resistance was 1011 ohms and capacitance 35 picofarads. The rise time and fall time were identical (5 µs) and constant. The selectable voltage or current output mode made it very convenient to use. The current mode, with higher output resistance values in low current ranges, permits intracellular stimulation even with tip resistances close to 100 megaohms. The high compliance of 200 V guarantees the value of the current stimulus. The very low output resistance in the voltage mode made the device highly suitable for extracellular stimulation with low impedance electrodes. Most importantly, these characteristics were achieved with a circuit that was easy to build and modify and assembled with components available in Brazil.

Patent DE10 2004 037 519 B4 “Sensor Process and Device for Determining a Physical Value“. A Proof of Concept

At present, a fraction of 0.1 - 0.2% of the patients undergoing surgery become aware during the process. The situation is referred to as anesthesia awareness and is obviously very traumatic for the person experiencing it. The reason for its occurrence is mostly an insufficient dosage of the narcotic Propofol combined with the incapability of the technology monitoring the depth of the patient’s anesthetic state to notice the patient becoming aware. A solution can be a highly sensitive and selective real time monitoring device for Propofol based on optical absorption spectroscopy. Its working principle has been postulated by Prof. Dr. habil. H. Hillmer and formulated in DE10 2004 037 519 B4, filed on Aug 30th, 2004. It consists of the exploitation of Intra Cavity Absorption effects in a two mode laser system. In this Dissertation, a two mode external cavity semiconductor laser, which has been developed previously to this work is enhanced and optimized to a functional sensor. Enhancements include the implementation of variable couplers into the system and the implementation of a collimator arrangement into which samples can be introduced. A sample holder and cells are developed and characterized with a focus on compatibility with the measurement approach. Further optimization concerns the overall performance of the system: scattering sources are reduced by re-splicing all fiber-to-fiber connections, parasitic cavities are eliminated by suppressing the Fresnel reflexes of all one fiber ends by means of optical isolators and wavelength stability of the system is improved by the implementation of thermal insulation to the Fiber Bragg Gratings (FBG). The final laser sensor is characterized in detail thermally and optically. Two separate modes are obtained at 1542.0 and 1542.5 nm, tunable in a range of 1nm each. Mode Full Width at Half Maximum (FWHM) is 0.06nm and Signal to Noise Ratio (SNR) is as high as 55 dB. Independent of tuning the two modes of the system can always be equalized in intensity, which is important as the delicacy of the intensity equilibrium is one of the main sensitivity enhancing effects formulated in DE10 2004 037 519 B4. For the proof of concept (POC) measurements the target substance Propofol is diluted in the solvents Acetone and DiChloroMethane (DCM), which have been investigated for compatibility with Propofol beforehand. Eight measurement series (two solvents, two cell lengths and two different mode spacings) are taken, which draw a uniform picture: mode intensity ratio responds linearly to an increase of Propofol in all cases. The slope of the linear response indicates the sensitivity of the system. The eight series are split up into two groups: measurements taken in long cells and measurements taken in short cells.

Restricting microbial exposure in early life negates the immune benefits associated with gut colonization in environments of high microbial diversity

Background: Acquisition of the intestinal microbiota in early life corresponds with the development of the mucosal immune system. Recent work on caesarean-delivered infants revealed that early microbial composition is influenced by birthing method and environment. Furthermore, we have confirmed that early-life environment strongly influences both the adult gut microbiota and development of the gut immune system. Here, we address the impact of limiting microbial exposure after initial colonization on the development of adult gut immunity. Methodology/Principal Findings: Piglets were born in indoor or outdoor rearing units, allowing natural colonization in the immediate period after birth, prior to transfer to high-health status isolators. Strikingly, gut closure and morphological development were strongly affected by isolator-rearing, independent of indoor or outdoor origins of piglets. Isolator-reared animals showed extensive vacuolation and disorganization of the gut epithelium, inferring that normal gut closure requires maturation factors present in maternal milk. Although morphological maturation and gut closure were delayed in isolatorreared animals, these hard-wired events occurred later in development. Type I IFN, IL-22, IL-23 and Th17 pathways were increased in indoor-isolator compared to outdoor-isolator animals during early life, indicating greater immune activation in pigs originating from indoor environments reflecting differences in the early microbiota. This difference was less apparent later in development due to enhanced immune activation and convergence of the microbiota in all isolator-reared animals. This correlated with elevation of Type I IFN pathways in both groups, although T cell pathways were still more affected in indoor-reared animals. Conclusions/Significance: Environmental factors, in particular microbial exposure, influence expression of a large number of immune-related genes. However, the homeostatic effects of microbial colonization in outdoor environments require sustained microbial exposure throughout development. Gut development in high-hygiene environments negatively impacts on normal succession of the gut microbiota and promotes innate immune activation which may impair immune homeostasis.

Environmentally-acquired bacteria influence microbial diversity and natural innate immune responses at gut surfaces

Background: Early microbial colonization of the gut reduces the incidence of infectious, inflammatory and autoimmune diseases. Recent population studies reveal that childhood hygiene is a significant risk factor for development of inflammatory bowel disease, thereby reinforcing the hygiene hypothesis and the potential importance of microbial colonization during early life. The extent to which early-life environment impacts on microbial diversity of the adult gut and subsequent immune processes has not been comprehensively investigated thus far. We addressed this important question using the pig as a model to evaluate the impact of early-life environment on microbe/host gut interactions during development. Results: Genetically-related piglets were housed in either indoor or outdoor environments or in experimental isolators. Analysis of over 3,000 16S rRNA sequences revealed major differences in mucosa-adherent microbial diversity in the ileum of adult pigs attributable to differences in earlylife environment. Pigs housed in a natural outdoor environment showed a dominance of Firmicutes, in particular Lactobacillus, whereas animals housed in a hygienic indoor environment had reduced Lactobacillus and higher numbers of potentially pathogenic phylotypes. Our analysis revealed a strong negative correlation between the abundance of Firmicutes and pathogenic bacterial populations in the gut. These differences were exaggerated in animals housed in experimental isolators. Affymetrix microarray technology and Real-time Polymerase Chain Reaction revealed significant gut-specific gene responses also related to early-life environment. Significantly, indoorhoused pigs displayed increased expression of Type 1 interferon genes, Major Histocompatibility Complex class I and several chemokines. Gene Ontology and pathway analysis further confirmed these results.

Neonatal environment exerts a sustained influence on the development of the intestinal microbiota and metabolic phenotype

The postnatal environment, including factors such as weaning and acquisition of the gut microbiota, has been causally linked to the development of later immunological diseases such as allergy and autoimmunity, and has also been associated with a predisposition to metabolic disorders. We show that the very early-life environment influences the development of both the gut microbiota and host metabolic phenotype in a porcine model of human infants. Farmpiglets were nursed by their mothers for 1 day, before removal to highly controlled, individual isolators where they received formula milk until weaning at 21 days. The experiment was repeated, to create two batches, which differed only in minor environmental fluctuations during the first day. At day 1 after birth, metabolic profiling of serum by 1H nuclear magnetic resonance spectroscopy demonstrated significant, systemic, inter-batch variation which persisted until weaning. However, the urinary metabolic profiles demonstrated that significant inter-batch effects on 3-hydroxyisovalerate, trimethylamine-N-oxide and mannitol persisted beyond weaning to at least 35 days. Batch effects were linked to significant differences in the composition of colonic microbiota at 35 days, determined by 16 S pyrosequencing. Different weaning diets modulated both the microbiota and metabolic phenotype independently of the persistent batch effects. We demonstrate that the environment during the first day of life influences development of the microbiota and metabolic phenotype and thus should be taken into account when interrogating experimental outcomes. In addition, we suggest that intervention at this early time could provide ‘metabolic rescue’ for at-risk infants who have undergone aberrant patterns of initial intestinal colonisation.

Force and displacement transmissibility of a nonlinear isolator with high-static-low-dynamic-stiffness

Engineers often face the challenge of reducing the level of vibrations experienced by a given payload or those transmitted to the support structure to which a vibrating source is attached. In order to increase the range over which vibrations are isolated, soft mounts are often used in practice. The drawback of this approach is the static displacement may be too large for reasons of available space for example. Ideally, a vibration isolator should have a high-static stiffness, to withstand static loads without too large a displacement, and at the same time, a low dynamic stiffness so that the natural frequency of the system is as low as possible which will result in an increased isolation region. These two effects are mutually exclusive in linear isolators but can be overcome if properly configured nonlinear isolators are used. This paper is concerned with the characterisation of such a nonlinear isolator comprising three springs, two of which are configured to reduce the dynamic stiffness of the isolator. The dynamic behaviour of the isolator supporting a lumped mass is investigated using force and displacement transmissibility, which are derived by modelling the dynamic system as a single-degree-of-freedom system. This results in the system dynamics being approximately described by the Duffing equation. For a linear isolator, the dynamics of the system are the same regardless if the source of the excitation is a harmonic force acting on the payload (force transmissibility) or a harmonic motion of the base (displacement transmissibility) on which the payload is mounted. In this paper these two expressions are compared for the nonlinear isolator and it is shown that they differ. A particular feature of the displacement transmissibility is that the response is unbounded at the nonlinear resonance frequency unless the damping in the isolator is greater than some threshold value, which is not the case for force transmissibility. An explanation for this is offered in the paper. (C) 2011 Elsevier Ltd. All rights reserved.

On the dynamic behaviour of a nonlinear system weakly connected to a linear single degree-of-freedom system

This paper discusses the dynamic behaviour of a nonlinear two degree-of-freedom system consisting of a harmonically excited linear oscillator weakly connected to a nonlinear attachment that behaves as a hardening Duffing oscillator. A system which behaves in this way could be a shaker (linear system) driving a nonlinear isolator. The mass of the nonlinear system is taken to be much less than that in the linear system and thus the nonlinear system has little effect on the dynamics of the linear system. Of particular interest is the situation when the linear natural frequency of the nonlinear system is less than the natural frequency of the linear system such that the frequency response curve of the nonlinear system bends to higher frequencies and thus interacts with the resonance frequency of the linear system. It is shown that for some values of the system parameters a complicated frequency response curve for the nonlinear system can occur; closed detached curves can appear as a part of the overall amplitude-frequency response. The reason why these detached curves appear is presented and approximate analytical expressions for the jump-up and jump-down frequencies of the system under investigation are given.

Passive vibration isolation using axially loaded curved beams

A nonlinear spring element of a vibration isolator should ideally possess high static and low dynamic stiffness. A buckled beam may be a good candidate to fulfil this requirement provided its internal resonance frequencies are high enough to achieve a wide frequency range of isolation. If a straight beam is used, there is a singularity in the force-displacement characteristic. To smooth this characteristic and eliminate the singularity at the buckling point, beams with initial constant curvature along their length are investigated here as an alternative to the buckled straight beam. Their force displacement characteristics are compared with different initial curvature and with a straight buckled beam. The minimum achievable dynamic stiffness with its corresponding static stiffness is compared for different initial curvatures. A case study is considered where the beams are optimized to isolate a one kilogram mass and to achieve a natural frequency of 1 Hz, considering small amplitudes of vibration. Resonance frequencies of the optimized beams for different curvature are presented. It is shown that an order of magnitude reduction in stiffness compared with a linear spring is achievable, while the internal resonance frequencies of the curved beam are high enough to achieve an acceptable frequency range of isolation.

A comparison of two nonlinear damping mechanisms in a vibration isolator

The vibration transmissibility characteristics of a single-degree-of- freedom (SDOF) passive vibration isolation system with different nonlinear dampers are investigated in this paper. In one configuration, the damper is assumed to be linear and viscous, and is connected to the mass so that it is perpendicular to the spring (horizontal damper). The vibration is in the direction of the spring. The second configuration is one in which the damper is in parallel with the spring but the damping force is proportional to the cube of the relative velocity across the damper (cubic damping). Both configurations are studied for small amplitudes of excitation, when some analysis can be conducted based on analytical expressions, and for large amplitudes of excitation, where the analysis is based on numerical simulations. It is found that the two nonlinear systems can outperform the linear system when force transmissibility is considered. However, for displacement transmissibility, the system with the horizontal damper exhibits some desirable properties, but the system with cubic damping does not. © 2012 Elsevier Ltd.

An investigation of a two-stage nonlinear vibration isolation system

This paper investigates the most desirable configuration of a two-stage nonlinear vibration isolation system, in which the isolators contain hardening geometric stiffness nonlinearity and linear viscous damping. The force transmissibility of the system is used as the measure of the effectiveness of the isolation system. The hardening nonlinearity is achieved by placing horizontal springs onto the suspended and intermediate masses, which are supported by vertical springs. It is found that nonlinearity in the upper stage has very little effect and thus serves little purpose. The nonlinearity in the lower stage, however, has a profound effect, and can significantly improve the effectiveness of the isolation system. Further, it is found that it is desirable to have high damping in the upper stage and very low damping in the lower stage. © 2012 Elsevier Ltd.

Isolamento passivo de vibrações aleatórias atuantes sobre equipamentos eletrônicos aeronaúticos embarcados

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

On the effects of mistuning a force-excited system containing a quasi-zero-stiffness vibration isolator

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Procedimenti di ottimizzazione di sistemi smorzati

La presente tesi riguarda lo studio di procedimenti di ottimizzazione di sistemi smorzati. In particolare, i sistemi studiati sono strutture shear-type soggette ad azioni di tipo sismico impresse alla base. Per effettuare l’ottimizzazione dei sistemi in oggetto si agisce sulle rigidezze di piano e sui coefficienti di smorzamento effettuando una ridistribuzione delle quantità suddette nei piani della struttura. È interessante effettuare l’ottimizzazione di sistemi smorzati nell’ottica della progettazione antisismica, in modo da ridurre la deformata della struttura e, conseguentemente, anche le sollecitazioni che agiscono su di essa. Il lavoro consta di sei capitoli nei quali vengono affrontate tre procedure numerico-analitiche per effettuare l’ottimizzazione di sistemi shear-type. Nel primo capitolo si studia l’ottimizzazione di sistemi shear-type agendo su funzioni di trasferimento opportunamente vincolate. In particolare, le variabili di progetto sono le rigidezze di piano, mentre i coefficienti di smorzamento e le masse di piano risultano quantità note e costanti durante tutto il procedimento di calcolo iterativo; per effettuare il controllo dinamico della struttura si cerca di ottenere una deformata pressoché rettilinea. Tale condizione viene raggiunta ponendo le ampiezze delle funzioni di trasferimento degli spostamenti di interpiano pari all’ampiezza della funzione di trasferimento del primo piano. Al termine della procedura si ottiene una ridistribuzione della rigidezza complessiva nei vari piani della struttura. In particolare, si evince un aumento della rigidezza nei piani più bassi che risultano essere quelli più sollecitati da una azione impressa alla base e, conseguentemente, si assiste ad una progressiva riduzione della variabile di progetto nei piani più alti. L’applicazione numerica di tale procedura viene effettuata nel secondo capitolo mediante l’ausilio di un programma di calcolo in linguaggio Matlab. In particolare, si effettua lo studio di sistemi a tre e a cinque gradi di libertà. La seconda procedura numerico-analitica viene presentata nel terzo capitolo. Essa riguarda l’ottimizzazione di sistemi smorzati agendo simultaneamente sulla rigidezza e sullo smorzamento e consta di due fasi. La prima fase ricerca il progetto ottimale della struttura per uno specifico valore della rigidezza complessiva e dello smorzamento totale, mentre la seconda fase esamina una serie di progetti ottimali in funzione di diversi valori della rigidezza e dello smorzamento totale. Nella prima fase, per ottenere il controllo dinamico della struttura, viene minimizzata la somma degli scarti quadratici medi degli spostamenti di interpiano. Le variabili di progetto, aggiornate dopo ogni iterazione, sono le rigidezze di piano ed i coefficienti di smorzamento. Si pone, inoltre, un vincolo sulla quantità totale di rigidezza e di smorzamento, e i valori delle rigidezze e dei coefficienti di smorzamento di ogni piano non devono superare un limite superiore posto all’inizio della procedura. Anche in questo caso viene effettuata una ridistribuzione delle rigidezze e dei coefficienti di smorzamento nei vari piani della struttura fino ad ottenere la minimizzazione della funzione obiettivo. La prima fase riduce la deformata della struttura minimizzando la somma degli scarti quadrarici medi degli spostamenti di interpiano, ma comporta un aumento dello scarto quadratico medio dell’accelerazione assoluta dell’ultimo piano. Per mantenere quest’ultima quantità entro limiti accettabili, si passa alla seconda fase in cui si effettua una riduzione dell’accelerazione attraverso l’aumento della quantità totale di smorzamento. La procedura di ottimizzazione di sistemi smorzati agendo simultaneamente sulla rigidezza e sullo smorzamento viene applicata numericamente, mediante l’utilizzo di un programma di calcolo in linguaggio Matlab, nel capitolo quattro. La procedura viene applicata a sistemi a due e a cinque gradi di libertà. L’ultima parte della tesi ha come oggetto la generalizzazione della procedura che viene applicata per un sistema dotato di isolatori alla base. Tale parte della tesi è riportata nel quinto capitolo. Per isolamento sismico di un edificio (sistema di controllo passivo) si intende l’inserimento tra la struttura e le sue fondazioni di opportuni dispositivi molto flessibili orizzontalmente, anche se rigidi in direzione verticale. Tali dispositivi consentono di ridurre la trasmissione del moto del suolo alla struttura in elevazione disaccoppiando il moto della sovrastruttura da quello del terreno. L’inserimento degli isolatori consente di ottenere un aumento del periodo proprio di vibrare della struttura per allontanarlo dalla zona dello spettro di risposta con maggiori accelerazioni. La principale peculiarità dell’isolamento alla base è la possibilità di eliminare completamente, o quantomeno ridurre sensibilmente, i danni a tutte le parti strutturali e non strutturali degli edifici. Quest’ultimo aspetto è importantissimo per gli edifici che devono rimanere operativi dopo un violento terremoto, quali ospedali e i centri operativi per la gestione delle emergenze. Nelle strutture isolate si osserva una sostanziale riduzione degli spostamenti di interpiano e delle accelerazioni relative. La procedura di ottimizzazione viene modificata considerando l’introduzione di isolatori alla base di tipo LRB. Essi sono costituiti da strati in elastomero (aventi la funzione di dissipare, disaccoppiare il moto e mantenere spostamenti accettabili) alternati a lamine in acciaio (aventi la funzione di mantenere una buona resistenza allo schiacciamento) che ne rendono trascurabile la deformabilità in direzione verticale. Gli strati in elastomero manifestano una bassa rigidezza nei confronti degli spostamenti orizzontali. La procedura di ottimizzazione viene applicata ad un telaio shear-type ad N gradi di libertà con smorzatori viscosi aggiunti. Con l’introduzione dell’isolatore alla base si passa da un sistema ad N gradi di libertà ad un sistema a N+1 gradi di libertà, in quanto l’isolatore viene modellato alla stregua di un piano della struttura considerando una rigidezza e uno smorzamento equivalente dell’isolatore. Nel caso di sistema sheat-type isolato alla base, poiché l’isolatore agisce sia sugli spostamenti di interpiano, sia sulle accelerazioni trasmesse alla struttura, si considera una nuova funzione obiettivo che minimizza la somma incrementata degli scarti quadratici medi degli spostamenti di interpiano e delle accelerazioni. Le quantità di progetto sono i coefficienti di smorzamento e le rigidezze di piano della sovrastruttura. Al termine della procedura si otterrà una nuova ridistribuzione delle variabili di progetto nei piani della struttura. In tal caso, però, la sovrastruttura risulterà molto meno sollecitata in quanto tutte le deformazioni vengono assorbite dal sistema di isolamento. Infine, viene effettuato un controllo sull’entità dello spostamento alla base dell’isolatore perché potrebbe raggiungere valori troppo elevati. Infatti, la normativa indica come valore limite dello spostamento alla base 25cm; valori più elevati dello spostamento creano dei problemi soprattutto per la realizzazione di adeguati giunti sismici. La procedura di ottimizzazione di sistemi isolati alla base viene applicata numericamente mediante l’utilizzo di un programma di calcolo in linguaggio Matlab nel sesto capitolo. La procedura viene applicata a sistemi a tre e a cinque gradi di libertà. Inoltre si effettua il controllo degli spostamenti alla base sollecitando la struttura con il sisma di El Centro e il sisma di Northridge. I risultati hanno mostrato che la procedura di calcolo è efficace e inoltre gli spostamenti alla base sono contenuti entro il limite posto dalla normativa. Giova rilevare che il sistema di isolamento riduce sensibilmente le grandezze che interessano la sovrastruttura, la quale si comporta come un corpo rigido al di sopra dell’isolatore. In futuro si potrà studiare il comportamento di strutture isolate considerando diverse tipologie di isolatori alla base e non solo dispositivi elastomerici. Si potrà, inoltre, modellare l’isolatore alla base con un modello isteretico bilineare ed effettuare un confronto con i risultati già ottenuti per il modello lineare.

Probing strongly correlated states of ultracold atoms in optical lattices

This thesis describes experiments which investigate ultracold atom ensembles in an optical lattice. Such quantum gases are powerful models for solid state physics. Several novel methods are demonstrated that probe the special properties of strongly correlated states in lattice potentials. Of these, quantum noise spectroscopy reveals spatial correlations in such states, which are hidden when using the usual methods of probing atomic gases. Another spectroscopic technique makes it possible to demonstrate the existence of a shell structure of regions with constant densities. Such coexisting phases separated by sharp boundaries had been theoretically predicted for the Mott insulating state. The tunneling processes in the optical lattice in the strongly correlated regime are probed by preparing the ensemble in an optical superlattice potential. This allows the time-resolved observation of the tunneling dynamics, and makes it possible to directly identify correlated tunneling processes.