Optimal laser intensity profiles for a uniform target illumination in direct-drive inertial confinement fusion

A numerical method providing the optimal laser intensity profiles for a direct-drive inertial confinement fusion scheme has been developed. The method provides an alternative approach to phase-space optimization studies, which can prove computationally expensive. The method applies to a generic irradiation configuration characterized by an arbitrary number NB of laser beams provided that they irradiate the whole target surface, and thus goes beyond previous analyses limited to symmetric configurations. The calculated laser intensity profiles optimize the illumination of a spherical target. This paper focuses on description of the method, which uses two steps: first, the target irradiation is calculated for initial trial laser intensities, and then in a second step the optimal laser intensities are obtained by correcting the trial intensities using the calculated illumination. A limited number of example applications to direct drive on the Laser MegaJoule (LMJ) are described.

A CFD study of Hong Kong refuge floor design : floor height effect

Since 1996, ther provision of a refuge floor has been a mandatory feature for all new tall buildings in Hong Kong. These floors are designed to provide for building occupants a fire safe environment that is also free from smoke. However, the desired cross ventilation on these floors to achieve the removal of smoke, assumed by the Building Codes of Hong Kong, is still being questioned so that a further scientific study of the wind-induced ventilation of a refuge fllor is needed. This paper presents an investigation into this issue. The developed computational technique used in this paper was adopted to study the wind-induced natural ventilation on a refuge floor. The aim of the investigation was to establish whether a refuge floor with a cetnral core and having cross ventilation produced by only two open opposite external side walls on the refuge floor would provide the required protection in all situations taking into account behaviour of wind due to different floor heights, wall boundary conditions and turbulence intensity profiles. The results revealed that natural ventilation can be increased by increasng the floor heigh provided the wind angle to the building is less than 90 degrees. The effectiveness of the solution was greatly reduced when the wind was blowing at 90 degrees to the refuge floor opening.

Modified conformation and physical properties in conducting polymers due to varying conjugation and solvent interactions

Small angle X-ray scattering (SAXS) studies of poly2-methoxy-5-(2'-ethyl-hexyloxy)-1,4-phenylene vinylene] (MEH-PPV) with varying conjugation, and polyethylene dioxythiophene complexed with polystyrene sulfonate (PEDOT-PSS) in different solvents have shown the importance of the role of pi-electron conjugation and solvent-chain interactions in controlling the chain conformation and assembly. In MEH-PPV, by increasing the extent of conjugation from 30 to 100%, the persistence length (l(p)) increases from 20 to 66 angstrom. Moreover, a pronounced second peak in the pair distribution function has been observed in the fully conjugated chain, at larger length scales. This feature indicates that the chain segments tend to self-assemble as the conjugation along the chain increases. In the case of PEDOT-PSS, the chains undergo solvent induced expansion and enhanced chain organization. The clusters formed by chains are better correlated in dimethyl sulfoxide (DMSO) solution than water, as observed in the scattered intensity profiles. The values of radius of gyration and the exponent (water: 2.6, DMSO: 2.31) of power-law decay, obtained from the unified scattering function (Beaucage) analysis, give evidence for chain expansion from compact (in water) to an extended coil in DMSO solutions, which is consistent with the Kratky plot analysis. The mechanism of this transition and the increase in dc conductivity of PEDOT-PSS in DMSO solution are discussed. The onset frequency for the increase in ac conduction, as well as its temperature dependence, probes the extent of the connectivity in the PEDOT-PSS system. The enhanced charge transport in PEDOT-PSS in DMSO is attributed to the extended chain conformation, as observed in the SAXS results.

Anomalous X-ray scattering study of local structures in the superionic conducting class (CuI)(0.3)(Cu2O)(0.35)(MoO3)(0.35)

The anomalous X-ray scattering (AXS) method using Cu and Mo K absorption edges has been employed for obtaining the local structural information of superionic conducting glass having the composition (CuI)(0.3)(Cu2O)(0.35)(MoO3)(0.35). The possible atomic arrangements in near-neighbor region of this glass were estimated by coupling the results with the least-squares analysis so as to reproduce two differential intensity profiles for Cu and Mo as well as the ordinary scattering profile. The coordination number of oxygen around Mo is found to be 6.1 at the distance of 0.187 nm. This implies that the MoO6 octahedral unit is a more probable structural entity in the glass rather than MoO4 tetrahedra which has been proposed based on infrared spectroscopy. The pre-peak shoulder observed at about 10 nm(-1) may be attributed to density fluctuation originating from the MoO6 octahedral units connected with the corner sharing linkage, in which the correlation length is about 0.8 nm. The value of the coordination number of I- around Cu+ is estimated as 4.3 at 0.261 nm, suggesting an arrangement similar to that in molten CuI.

Anomalous X-ray scattering study of local structures in the superionic conducting glass (AgBr)0.4 (Ag2O)0.3 (GeO2)0.3

The local structural information in the near-neighbor region of superionic conducting glass (AgBr)0.4(Ag2O)0.3(GeO2)0.3 has been estimated from the anomalous X-ray scattering (AXS) measurements using Ge and Br K absorption edges. The possible atomic arrangements in the near-neighbor region of this glass were obtained by coupling the results with the least-squares variational method so as to reproduce two differential intensity profiles for Ge and Br as well as the ordinary scattering profile. The coordination number of oxygen around Ge is found to be 3.6 at a distance of 0.176 nm, suggesting the GeO4 tetrahedral unit as the probable structural entity in this glass. Moreover, the coordination number of Ag around Br is estimated as 6.3 at a distance of 0.284 nm, suggesting an arrangement similar to that in crystalline AgBr.

Influence of recording conditions on crossed-beam photorefractive gratings in doubly doped LiNbO3 crystals

The influence of the recording conditions, including the widths of the recording beams, the width ratio of the recording beams, and the recording angles, on the properties of crossed-beam photorefractive gratings in doubly doped LiNbO3 crystals is studied. A theoretical model that combines the band transport model with two-dimensional coupled-wave theory is proposed. The numerical calculations of the space-charge field, the intensity profiles of the diffracted beam, and the diffraction efficiency are presented. (C) 2006 Optical Society of America.

Smoothing effect in the broadband laser through a dispersive wedge

The propagation expression of a broadband laser passing through a dispersive wedge is derived on the basis of the Huygens-Fresnel diffraction integral, Smoothing effects caused by the phase perturbation of the dispersive wedge on the intensity profiles are investigated in detail. The phase perturbation of the dispersive wedge induces a relative transverse position shift between the diffraction patterns of different frequency components. The relative transverse position shift is of great benefit to the fill of the intensity peaks of some patterns in the valleys of others when these patterns are overlapped and thus the smoothing effect is achieved. (c) 2006 Elsevier B.V. All rights reserved.

傅立叶分解法荧光层析成像

本文提出一种基于结构光照明和傅立叶分解方法的荧光层析成像技术，该技术首先将激发光的强度沿着光轴方向调制成余弦函数，然后用此激发光对样品作传统的二维扫描，在每一个扫描位置余弦函数的频率在一定的范围内扫描，同时一一对应地记录下所发出的荧光强度。只要对所纪录的荧光序列做一个简单的傅立叶变换，即可以得到此位置样品沿着光轴方向的荧光团分布。这样通过一个传统的二维扫描，就可以得到一个三维的阳样品分布。

The analytical description and experiments of the optical bottle generated by an axicon and a lens

Based on the interferential theory, we deduce a new type of analytic expression suitable for describing the evolutions of the optical bottle beam generated from the axicon-lens optical system illuminated by the Gaussian beam for the first time. The theory does not use much approximation in the process of mathematical analysis and can better illustrate the optical bottle beam evolutions at any positions. With the derived expression, the three-dimensional (3D) longitudinal and transverse intensity profiles of the optical bottle beam are simulated numerically. The numerical calculations have been confirmed by the experimental results.

Raman scattering detection of stacking faults in free-standing cubic-SiC epilayer

We report on stacking fault (SF) detection in free-standing cubic-SiC epilayer by the Raman measurements. The epilayer with enhanced SFs is heteroepitaxially grown by low pressure chemical vapour deposition on a Si(100) substrate and is released in KOH solution by micromechanical manufacture, on which the Raman measurements are performed in a back scattering geometry. The TO line of the Raman spectra is considerably broadened and distorted. We discuss the influence of SFs on the intensity profiles of TO mode by comparing our experimental data with the simulated results based on the Raman bond polarizability (BP) model in the framework of linear-chain concept. Good agreement with respect to the linewidth and disorder-induced peak shift is found by assuming the mean distance of the SFs to be 11 angstrom in the BP model.

Characteristics of beam profile of Gaussian beam passing through an axicon

Bessel beam can overcome the limitation of the Rayleigh range of Gaussian beam with the same spot size propagation without any spreading due to diffraction, which is considered as an useful function in guiding particles in the next generation of optical tweezers. The mathematical description of the Bessel beam generated by an axicon is usually based on the Fresnel diffraction integral theory. In this paper, we deduce another type of analytic expression suitable for describing the beam profile generated from the axicon illuminated by the Gaussian beam based on the interferential theory. Compared with the Fresnel diffraction integral theory, this theory does not use much approximation in the process of mathematical analysis. According to the derived expression, the beam intensity profiles at any positions behind the axicon can be calculated not just restricted inside the cross region as the Fresnel diffraction integral theory gives. The experiments prove that the theoretical results fit the experimental results very well. (C) 2004 Elsevier B.V. All rights reserved.

A non-parametric vessel detection method for complex vascular structures

Modern medical imaging techniques enable the acquisition of in vivo high resolution images of the vascular system. Most common methods for the detection of vessels in these images, such as multiscale Hessian-based operators and matched filters, rely on the assumption that at each voxel there is a single cylinder. Such an assumption is clearly violated at the multitude of branching points that are easily observed in all, but the Most focused vascular image studies. In this paper, we propose a novel method for detecting vessels in medical images that relaxes this single cylinder assumption. We directly exploit local neighborhood intensities and extract characteristics of the local intensity profile (in a spherical polar coordinate system) which we term as the polar neighborhood intensity profile. We present a new method to capture the common properties shared by polar neighborhood intensity profiles for all the types of vascular points belonging to the vascular system. The new method enables us to detect vessels even near complex extreme points, including branching points. Our method demonstrates improved performance over standard methods on both 2D synthetic images and 3D animal and clinical vascular images, particularly close to vessel branching regions. (C) 2008 Elsevier B.V. All rights reserved.

Needleless electrospinning. I. A comparison of cylinder and disk nozzles

In this study, we demonstrated the needleless electrospinning of poly(vinyl alcohol) (PVA) nanofibers with two nozzles, a rotating disk and a cylinder, and examined the effect of the nozzle shape on the electrospinning process and resultant fiber morphology. The disk nozzle needed a relatively low applied voltage to initiate fiber formation, and the fibers were mainly formed on the top disk edge. Also, the PVA concentration had little influence on the disk electrospinning process (up to 11 wt %). In comparison, the cylinder electrospinning showed a higher dependence on the applied voltage and polymer concentration. The fibers were initiated from the cylinder ends first and then from the entire cylinder surface only if the applied voltage were increased to a certain level. With the same polymer solution, the critical voltage needed to generate nanofibers from the disk nozzle was lower than that needed to generate nanofibers from the cylinder. Both electrospinning systems could produce uniform nanofibers, but the fibers produced from the disk nozzle were finer than those from the cylinder when the operating conditions were the same. A thin disk (8 cm in diameter and 2 mm thick) could produce nanofibers at a rate similar to that of a cylinder of the same diameter but 100 times wider (i.e., 20 cm long). Finite element analysis of electric field profiles of the nozzles revealed a concentrated electric field on the disk edge. For the cylinder nozzle, an uneven distribution of the electric field intensity profile along the nozzle surface was observed. The field lines were mainly concentrated on the cylinder ends, with a much lower electric field intensity formed in the middle surface area. At the same applied voltage, the electric field intensity on the disk edge was much higher than that on the cylinder end. These differences in the electric field intensity profiles could explain the differences in the fiber fineness and rate of the nanofibers produced from these two nozzles. These findings will benefit the design and further development of large-scale electrospinning systems for the mass production of nanofibers for advanced applications.

Needleless Electrospinning of nanofibers with a conical wire coil

In this article, we have demonstrated a novel needleless electrospinning of PVA nanofibers by using a conical metal wire-coil as spinneret. Multiple polymer jets were observed to generate on the coil surface. Up to 70 kV electric voltage can be applied to this needleless electrospinning nozzle without causing corona discharge. Compared with conventional needle electrospinning, this needleless electrospinning system produced finer nanofibers on a much larger scale, and the fiber processing ability showed a much greater dependence on the applied voltage. Finite element calculation indicates that the electric field intensity profiles for the two systems are also quite different. This novel concept of using wire coil as the electrospinning nozzle will contribute to the further development of new large-scale needleless electrospinning system for nanofiber production.