Efeito do agregado na diminuição da retracção de argamassas

Na actualidade, face ao desenvolvimento de betões de alto desempenho caracterizados por apresentarem muito baixa razão água cimento (A/C), tornou-se pertinente o estudo da retracção autogénea, por motivos relacionados com a resistência, durabilidade e estética destes materiais. Nesta dissertação foi elaborado um estudo prático com o intuito de avaliar o impacto da adição de agregado na redução da retracção autogénea, em seis misturas cimentícias. Através de ensaios foram obtidos valores reais de retracção autogénea, sendo estes posteriormente comparados com os valores obtidos teoricamente com recurso ao modelo proposto por Hobbs na década de 70. Tendo em consideração os valores teóricos e sua comparação com os valores reais obtidos nos ensaios é proposta uma alteração ao modelo teórico, que tem em conta a maior resistência à compressão dos betões actuais. Esta modificação permitiu estimar com maior exactidão os valores de retracção autogénea nas diferentes misturas. /ABSTRACT: Nowadays the development of high performance concretes characterized by a low water-to­ cement ratio (W/C), it became relevant to study the autogenous shrinkage, for reasons relating to the strength, durability and aesthetics of these materials. ln this study the effect of adding aggregate in six cementitious mixtures was evaluated. The results obtained in the experimental test were compared with theoretical values from a model propose by Hobbs in the 70's for autogenous shrinkage. Given the theoretical values and its comparison with the actual values obtained in the tests an amendment is proposed to the theoretical model that takes into account the higher compressive strength of actual concrete. This modification allowed us to estimate accurately the values of autogenous shrinkage in the different mixtures.

Concreto celular polimérico: influência na adição de resíduo de poliéster insaturado termofixo

This work addresses the production of lightweight concrete building elements, such as plates, prefabricated slabs for pre-molded and panels of fencing, presenting a singular concrete: the Lightweight Concrete, with special properties such low density and good strength, by means of the joint use of industrial waste of thermosetting unsaturated polyesters and biodegradable foaming agent, named Polymeric Lightweight Concrete. This study covered various features of the materials used in the composition of the Polymeric Lightweight Concrete, using a planning of factorial design 23, aiming at studying of the strength, production, dosage processes, characterization of mechanical properties and microstructural analysis of the transition zone between the light artificial aggregate and the matrix of cement. The results of the mechanical strength tests were analyzed using a computational statistics tool (Statistica software) to understand the behavior and obtain the ideal quantity of each material used in the formula of the Polymeric Lightweight Concrete. The definition of the ideal formula has the purpose of obtaining a material with the lowest possible dry density and resistance to compression in accordance with NBR 12.646/92 (≥ 2.5 MPa after 28 days). In the microstructural characterization by scanning electron microscopy it was observed an influence of the materials in the process of cement hydration, showing good interaction between the wrinkled face of the residue of unsaturated polyesters thermosetting and putty and, consequently, the final strength. The attaining of an ideal formula, given the Brazilian standards, the experimental results obtained in the characterization and comparison of these results with conventional materials, confirmed that the developed Polymeric Lightweight Concrete is suitable for the production of building elements that are advantageous for construction

Influência da substituição de areia natural por pó de pedra no comportamento mecânico, microestrutural e eletroquímico de concretos

The construction industry is one of the largest consumers of natural raw materials, and concrete is considered today the most used material wide. This accentuated consumption of natural resources has generated concern with the preservation of the environment, and has motivated various studies related to the use of resid ues, which can partially or entirely substitute, with satisfactory performance, some materials such as the aggregate, and in so doing, decrease the impact on the environment caused by the produced residues. Research has been done to better understand and improve the microstructure of concrete, as well as to understand the mechanism of corrosion in reinforced steel. In this context, this work was developed aiming at discovering the influence of the substitution of natural sand by artificial sand, with rega rd to mechanical resistance, microstructure, and durability. To obtain the electrochemical parameters, an adaptation was made to the galvanostatic electrochemical method to study the corrosion in reinforced steel. Concretes of categories 20 MPa and 40 MPa were produced, containing natural sand, and concretes of the same categories were produced with artificial sand substituting the natural sand, and with the addition of sodium nitrate and sodium chloride. Due to the use of rock dust reject (artificial sand), an evaluation was made of its environmental risk. The results indicate that the concretes of category 20 MPa present a better performance than the concrete made with natural sand, thus making it a viable substitute. For the category 40 MPa, the better performance is from the concrete containing natural sand. The adaptation of the galvanostatic electrochemical technique to the study of the corrosion of reinforced steel within concrete proved to be valid for obtaining electrochemical parameters with a high degree of reliability, considering the number of degrees of freedom

Influência da formação de pozolanas com adição de metacaulim em concreto de alta resistência

The need to build durable structures and resistant to harsh environments enabled the development of high strength concrete, these activities generate a high cement consumption, which implies factor in CO2 emissions. Often the desired strength is not achieved using only the cement composition. This study aims to evaluate the influence of pozzolans with the addition of metakaolin on the physical mechanics of high strength concrete comparing them with the standard formulation. Assays were performed to characterize the aggregates according to NBR 7211, evaluation of cement and coarse aggregate through the trials of petrography (NBR 15577-3/08) and alkali-aggregate reaction (NBR 15577-05/08). Specimens were fabricated according to NBR 5738-1/04 with additions of 0%, 4%, 6%, 8% and 10% of metakaolin for cement mortars CP V in the formulations. For evaluation of the concrete hardened in fresh state and scattering assays were performed and compressive strength in accordance with the NBR 7223/1992 and NBR 5739-8/94 respectively. The results of the characterization of aggregates showed good characteristics regarding size analysis and petrography, as well as potentially innocuous as the alkali-aggregate reaction. As to the test of resistance to compression, all the formulations with the addition of metakaolin showed higher value at 28 days of disruption compared with the standard formulation. These results present an alternative to reduce CO2 emissions, and improvements in the quality and durability of concrete, because the fine particle size of metakaolin provides an optimal compression of the mass directly influencing the strength and rheology of the dough

Influência do estresse nutricional programado na composição da microalga isochrysis galbana

Global warming due to Greenhouse Gases (GHG) emissions, especially CO2, has been identified as one of the major problems of the twenty-first century, considering the consequences that could represent to planet. Currently, biological processes have been mentioned as a possible solution, especially CO2 biofixation due to association microalgae growth. This strategy has been emphasized as in addition to CO2 mitigation, occurs the production of biomass rich in compounds of high added value. The Microalgae show high photosynthetic capacity and growth rate higher than the superior plants, doubling its biomass in one day. Its culture does not show seasons, they grow in salt water and do not require irrigation, herbicides or pesticides. The lipid content of these microorganisms, depending on the species, may range from 10 to 70% of its dry weight, reaching 90% under certain culture conditions. Studies indicate that the most effective method to promote increased production of lipids in microalgae is to induce stress by limiting nitrogen content in the culture medium. These evidences justify research continuing the production of biofuels from microalgae. In this paper, it was studied the strategy of increasing the production of lipids in microalgae I. galbana with programmed nutritional stress, due to nitrogen limitation. The physiological responses of microalgae, grown in f / 2 with different concentrations of nitrogen (N: P 15,0-control, N: 5,0 P and N: P 2,5) were monitored. During exponential phase, results showed invariability in the studied conditions. However the cultures subjected to stress in stationary phase, showed lower biomass yields. There was an increase of 32,5% in carbohydrate content and 87.68% in lipids content at N: P ratio of 5,0 and an average decrease of 65% in protein content at N: P ratios of 5, 0 and 2.5. There were no significant variations in ash content, independently of cultivation and growth phase. Despite the limitation of biomass production in cultures with N: P smaller ratios, the increase of lipid accumulation highest lipids yields were observed as compared to the control culture. Given the increased concentration of lipids associated to stress, this study suggests the use of microalgae Isochrysis galbana as an alternative raw material for biofuel production

Valor agregado ao cachara Pseudoplatystoma fasciatum: efeito da sazonalidade e da defumação

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Influência do preparo biomecânico na microdureza e selamento marginal do MTA e do polímero derivado da mamona em perfurações radiculares simuladas

Pós-graduação em Odontologia Restauradora - ICT

Estudo da influência da adição de borracha vulcanizada em concreto à temperatura ambiente e elevada temperatura

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Influência da qualidade das lâminas no desempenho físico-mecânico de painéis compensados de Hevea brasiliensis

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Estimativas da condutividade térmica dos minerais e rochas e influência de parâmetros térmicos e petrofísicos na resistividade aparente da formação

O presente estudo realiza estimativas da condutividade térmica dos principais minerais formadores de rochas, bem como estimativas da condutividade média da fase sólida de cinco litologias básicas (arenitos, calcários, dolomitos, anidritas e litologias argilosas). Alguns modelos térmicos foram comparados entre si, possibilitando a verificação daquele mais apropriado para representar o agregado de minerais e fluidos que compõem as rochas. Os resultados obtidos podem ser aplicados a modelamentos térmicos os mais variados. A metodologia empregada baseia-se em um algoritmo de regressão não-linear denominado de Busca Aleatória Controlada. O comportamento do algoritmo é avaliado para dados sintéticos antes de ser usado em dados reais. O modelo usado na regressão para obter a condutividade térmica dos minerais é o modelo geométrico médio. O método de regressão, usado em cada subconjunto litológico, forneceu os seguintes valores para a condutividade térmica média da fase sólida: arenitos 5,9 ± 1,33 W/mK, calcários 3.1 ± 0.12 W/mK, dolomitos 4.7 ± 0.56 W/mK, anidritas 6.3 ± 0.27 W/mK e para litologias argilosas 3.4 ± 0.48 W/mK. Na sequência, são fornecidas as bases para o estudo da difusão do calor em coordenadas cilíndricas, considerando o efeito de invasão do filtrado da lama na formação, através de uma adaptação da simulação de injeção de poços proveniente das teorias relativas à engenharia de reservatório. Com isto, estimam-se os erros relativos sobre a resistividade aparente assumindo como referência a temperatura original da formação. Nesta etapa do trabalho, faz-se uso do método de diferenças finitas para avaliar a distribuição de temperatura poço-formação. A simulação da invasão é realizada, em coordenadas cilíndricas, através da adaptação da equação de Buckley-Leverett em coordenadas cartesianas. Efeitos como o aparecimento do reboco de lama na parede do poço, gravidade e pressão capilar não são levados em consideração. A partir das distribuições de saturação e temperatura, obtém-se a distribuição radial de resistividade, a qual é convolvida com a resposta radial da ferramenta de indução (transmissor-receptor) resultando na resistividade aparente da formação. Admitindo como referência a temperatura original da formação, são obtidos os erros relativos da resistividade aparente. Através da variação de alguns parâmetros, verifica-se que a porosidade e a saturação original da formação podem ser responsáveis por enormes erros na obtenção da resistividade, principalmente se tais "leituras" forem realizadas logo após a perfuração (MWD). A diferença de temperatura entre poço e formação é a principal causadora de tais erros, indicando que em situações onde esta diferença de temperatura seja grande, perfilagens com ferramentas de indução devam ser realizadas de um a dois dias após a perfuração do poço.

Influência do teor de cinza volante na reologia de argamassa de assentamento: fabricado com reciclagem de resíduos

As argamassas podem ser consideradas como um conjunto de partículas sólidas em suspensão (agregado miúdo), aglomerantes e água (pasta de cimento). Sendo assim, seu comportamento reológico durante a cura pode ser influenciado por fatores como a granulometria, composição e teor de água incorporado. Este trabalho estudou as características reológicas de seis composições de argamassas, em função do teor de cinza volante, como material de atividade pozolânica, em substituição parcial do cimento. A argamassa estudada utilizou como base agregado o resíduo da construção civil (RCC), devidamente caracterizado por difratometria e fluorescência de raios-X. Formularam-se composições de argamassas para os ensaios reológicos com adição de resíduo de construção civil (RCC) nas proporções de 95, 90, 85, 80, 75 e 70%; cinzas volantes (CV) 0, 5, 10, 15, 20 e 25% e 5% de Cimento Portland Comum (CP II- E 32), sendo que em cada amostra foi incorporado 35% de água. Utilizou-se o viscosímetro modelo VT 550, com sensor tipo cilindros coaxiais SV₁ – Haake a temperatura de 28ºC. Para avaliar o tempo de cura do material programou-se uma taxa de cisalhamento constante 53,4 s^-1 em 1h e 45min, sendo avaliado o torque em intervalos de 15min. Para a elaboração das curvas de fluxo e curvas de histerese, utilizou-se a taxa de cisalhamento entre 0 e 600 s^-1 no intervalo de tempo de 120s. Os resultados mostraram que a incorporação de cinza volante foi o principal fator para aumento do torque no tempo de cura das argamassas e mudança do comportamento de reópetico para tixotrópico, nos traços analisados. Os dados experimentais das formulações propostas ajustaram-se ao modelo reológico de Herschel-Bulkley.

Influência da luz LED na cultura celular de Mieloma múltiplo murino–NS1 in vitro

A monoclonal antibody (mAb) is an important tool in medical biotechnology and the production of biopharmaceuticals, especially for disease diagnosis and treatment of infections, because the antibodies have a significant advantage over chemical agents used in conventional therapies . The last thirty years the technology of production of monoclonal antibodies developed mainly the technique of obtaining in vitro, but also of their production is laborious, the cost is high. A major element of the high cost of production is the fact that the long-term culture consumes a large amount of imported inputs with high added value. A major contribution of this work is to promote cell growth more quickly and efficiently. Currently, a great race to discover new technologies and techniques to synthesize new antibodies and significantly increase the production of murine mAbs. New technologies such as laser and LED are innovations and widespread in modern life, so much so that its use has proliferated worldwide, primarily in the medical field. Recent studies show a series of results from the influence of the LED light in biological tissues such as: increasing the rate of cell proliferation, increased production rate of fibroblasts, increasing the rate of synthesis of RNA and DNA synthesis of ATP, etc. To assess the contribution of the LED in the culture of Myeloma NS1murino compared to the standard procedure. - NS1 cells were provided and followed the criteria of culture medium of the Laboratory of Cellular Engineering Center of Botucatu (POPs). The same amount of cells was grown in bottles of 25 cm2 polystyrene Tissue Culture Treated, specifically marked and kept in special medium RPMI 1640 Gibco BRL  supplemented with fetal bovine serum 10%, essential amino acids and non-essential, glucose, insulin and antibiotics. It was used in LEDs Cromatek wavelength of 630nm, 475nm and 530nm. The groups were... (Complete abstract click electronic access below)