Industrial noise control manual /

Mode of access: Internet.

Attributable fraction of work accidents related to occupational noise exposure in a Southeastern city of Brazil

Noise is the most frequent type of occupational exposure and can lead to both auditory and extra-auditory dysfunction as well as increasing the risk of work accidents. The purpose of this study was to estimate the attributable fraction of work accidents related to occupational noise exposure in a medium-sized city in Southeast Brazil. In this hospital-based case-control study, including 600 cases and 822 controls, the odds ratio of work accidents (controlled for several covariables) was obtained classifying occupational noise exposure into four levels and determining the prevalence at each level. Based on these data, the calculated attributable fraction was 0.3041 (95%CI: 0.2341-0.3676), i.e., 30% of work accidents in the study area were statistically associated with occupational noise exposure. The authors discuss the causes of this association and the implications for the prevention of work accidents.

Exposição ocupacional ao ruído e acidentes do trabalho

The purpose of this study was to verify whether occupational noise exposure is a significant risk factor for work accidents in the city of Piracicaba, São Paulo State, Brazil. This hospital-based case-control study included 600 workers aged 15-60 who suffered typical occupational accidents between May and October 2004 and were seen at the Piracicaba Orthopedics and Trauma Center. The control group comprised 822 workers, aged 15-60, who were also seen at the Center, and either had a non-occupational accident or were accompanying someone who had suffered an accident. A multiple logistic regression model was adjusted with work accident as an independent variable, controlled by covariables of interest such as noise exposure. The risk of having a work accident was about twice as high among workers exposed to noise, after controlling for several covariables. Occupational noise exposure not only affected auditory health status but was also a risk factor for work accidents.

Interação entre grau de perda auditiva e o incômodo com zumbidos em trabalhadores com história de exposição ao ruído

Hearing loss and tinnitus impact the lives of workers in every instance of their lives. Aim: this paper aims to investigate the existence of a dose-response relationship between hearing loss and tinnitus by determining whether higher levels of hearing loss can be associated with increased tinnitus-related discomfort. Materials and method: this cross-sectional case study assessed 284 workers exposed to occupational noise through pure tone audiometry. Test results were categorized as defined by Merluzzi. Individuals complaining of tinnitus answered the adapted and validated Brazilian Portuguese version of the Tinnitus Handicap Inventory. A generalized linear model was adjusted for binomial data to test the interaction between these factors. Results: over 60% of the ears analyzed had hearing loss, while more than 46% of them had tinnitus. Tinnitus prevalence and risk rates increased as pure tone audiometry results got worse. The association between both, considering all hearing loss degrees, was statistically significant. Conclusion: the results point to a statistical association between hearing loss and tinnitus; the greater the hearing loss, the greater the discomfort introduced by tinnitus. 2009 © Revista Brasileira de Otorrinolaringologia.

Interventions to promote the wearing of hearing protection

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Medida del ruido ambiental en el CEIS. Análisis y evaluación de los datos

El presente documento, evalúa y analiza el ruido existente en las inmediaciones del CEIS (Centro Estudio, Innovación y Servicios), situado en la carretera Villaviciosa de Odón a Móstoles (M-856) en el Km 1,5. El objetivo es obtener datos de nivel de ruido en función del tiempo para conocer su variabilidad a lo largo de la semana, para promover una intercomparación entre laboratorios con ruido real. La zona que contempla el proyecto tiene variedad de ruido medioambiental: ruido de tráfico rodado, ruido industrial, ruido de instalaciones y ruido de tráfico aéreo. Estas fuentes de ruido pueden presentarse en diversas combinaciones. Para el ruido total existente, se analiza por un lado el ruido específico de la carretera M-856, y por otro lado el ruido residual asociado a sucesos aislados, como el ruido de tráfico aéreo, ruido industrial y de instalaciones. Para el cálculo de los niveles sonoros de la zona se realiza una evaluación del índice de ruido Ld, para el periodo de día, utilizando como herramienta de cálculo el programa CadnaA versión 4.2. Se realiza la validación de los niveles sonoros obtenidos en el CadnaA en las inmediaciones de la carretera Villaviciosa de Odón a Móstoles. Para ello se comparan los niveles obtenidos en el modelo acústico de la zona elaborado mediante CadnaA y los niveles medidos “in-situ”. Una vez obtenidos los niveles sonoros, se calcula la incertidumbre de las medidas ejecutadas “in-situ” en la última jornada de mediciones realizada, correspondientes a niveles de presión sonora continuos equivalente ponderado A (LAeq, 5min) y de las medidas simuladas en CadnaA , teniendo en cuenta las posibles desviaciones ocasionadas por el equipo de medida, condiciones meteorológicas, variaciones del tráfico, metodología de ensayo..... Por último se valoran los datos obtenidos y se evalúa la posibilidad de promover una intercomparación entre laboratorios realizada con el ruido real de tráfico de la zona. ABSTRACT. The next document evaluates the noise in sorrounding areas of CEIS (Centro Estudio, Innovación y Servicios), located in the road from Villaviciosa de Odón to Móstoles (M-856), in 1.5 km. The aim of this project is to get precise information during time to promove an intercomparation between laboratories with real noise. The area included in the project has several environmental noise: traffic noise, industrial noise and air traffic noise. These noise sources can be combined in different ways. The specific noise of the M-856 on one hand, and the residual noise associated with air traffic noise and industrial noise on the other. The calculation tool CadnaA, 4.2 version, simulates sound levels for the day period and the index Ld. The validation of sound levels around the road Villaviciosa de Odon to Móstoles, is made by comparing the obtained levels in the acoustic model and the real measured levels “in situ” . The uncertainty of the measures "in-situ", and the uncertainty of the sound levels simulated in the acoustic model CadnaA, is calculated using the measurements “in situ” (LAeq, 5min) of the last day. For that calculation, is necessary to take into account the deviations resulting from the measurement equipment, weather conditions, traffic variations, test methodology.... Finally the obtained data are evaluated, considering the possibility of promote an intercomparison between laboratories with real traffic noise of the area.

Evaluación de ruido ambiental en las zonas de uso residencial ubicadas en la zona de influencia de la Avenida San Pablo (Barrio de la Estación, Coslada)

El presente documento analiza y evalúa el ruido ambiental existente en las zonas de uso residencial ubicadas en el Barrio de “La Estación”, en el entorno de la Avenida San Pablo, pertenecientes al municipio de Coslada (Madrid). La zona que contempla el proyecto es muy completa, ya que en ella están presentes diferentes tipos de ruido medioambiental (tráfico ferroviario, tráfico rodado, tráfico aeroportuario, ruido industrial de instalaciones, ruido de actividades, etc), donde las fuentes de ruido pueden manifestarse aisladas o en diversas combinaciones. Para evaluar el ruido total existente, se analiza por un lado el ruido residual de la zona de estudio, y por otro el ruido específico e intermitente asociado a sucesos aislados, como son el ruido de aviones y el ruido de trenes, donde se estudia individualmente la existencia de componentes de tonalidad, baja frecuencia e impulsividad. Una vez obtenidos los niveles de ruido total y ruido residual en la zona objeto de estudio, el índice Nivel de presión sonora promedio LPm de las muestras analizadas, estima correctamente los niveles obtenidos en el muestreo de larga duración. En las medidas realizadas se detecta la existencia de componentes de tonalidad y baja frecuencia en los pasos de aviones y trenes registrados. Se calculan los niveles sonoros existentes en la zona de estudio. Para ello se realiza una evaluación de los índices de ruido Ld, para el periodo día, y Le, para el periodo tarde, utilizando como herramienta de cálculo el programa IMMI 6.3.1e. Se realiza la validación del mapa de niveles sonoros obtenido con el IMMI 6.3.1e. Para ello se hace una comparación entre los niveles calculados con el modelo, y los niveles medidos “in situ” en los puntos de muestreo. Por último se obtiene la incertidumbre en cada una de las medidas ejecutadas en una segunda campaña “in situ”, correspondientes a niveles de presión sonora continuos equivalentes ponderado A (LAeq,5min), teniendo en cuenta las posibles desviaciones ocasionadas por el equipo de medida, condiciones meteorológicas, procedimiento de realización del ensayo, etc. ABSTRACT. The present document analyzes and evaluates the environmental noise in the residential areas located at “La Estación” district, near the San Pablo Avenue, in the Coslada municipality (Madrid). The area considered in this project is very complete, once it covers different types of environmental noise (railway traffic, vehicular traffic, airport traffic, industrial noise of building systems, activities noise, etc), where noise sources may appear isolated or under several combinations. In order to evaluate the existing total noise, on one hand it is analyzed the residual noise in the study area, and on the other hand it is analyzed the specific and intermittent noise associated to isolated occurrences, such as the noise of the aircrafts and the noise of the trains, where the existence of components of tonality, low frequency and impulsiveness is studied individually. After obtaining the levels of total noise and residual noise in the target study area, the sound pressure level average index (LPm) of the analyzed samples estimates correctly the levels obtained in the sampling of long duration. On what concerns the measures carried out, it is detected the existence of components of tonality and low frequency in the registered aircrafts and trains passage. The sound levels of the study area are calculated. For that it is made a valuation of the Ld noise ratio, concerning the day period, and Le, concerning the afternoon period. The calculation tool used is the IMMI 6.3.1e programme. The validation of the map of sound levels obtained with the IMMI 6.3.1e is made. In order to get this validation, it is made a comparison between the levels calculated with the model and the levels measured “in situ” in the sampling points. Finally the uncertainty is obtained in each one of the measurements made in a second sampling “in situ”, correspondent to equivalent A-weighted continuous sound pressure level (LAeq,5 min), having in mind the possible deviations caused by the equipment of measure, meteorological conditions, essay’s execution procedures, etc.

Economic impact of removing numerical limits on sound emissions to class C land, R76-19 /

"Project no. 30.014."

Hearing protectors: a dilemma involving acoustics and personal safety

This thesis is concerned with the optimising of hearing protector selection. A computer model was used to estimate the reduction in noise exposure and risk of occupational deafness provided by the wearing of hearing protectors in industrial noise spectra. The model was used to show that low attenuation hearing protectors con provide greater protection than high attenuation protectors if the high attenuation protectors ore not worn for the total duration of noise exposure; or not used by a small proportion of the population. The model was also used to show that high attenuation protectors will not necessarily provide significantly greater reduction in risk than low attenuation protectors if the population has been exposed to the noise for many years prior to the provision of hearing protectors. The effects of earplugs and earmuffs on the localisation of sounds were studied to determine whether high attenuation earmuffs are likely to have greater potential than the lower attenuation earplugs for affecting personal safety. Laboratory studies and experiments at a foundry with normal-hearing office employees and noise-exposed foundrymen who had some experience of wearing hearing protectors showed that although earplugs reduced the ability of the wearer to determine the direction of warning sounds, earmuffs produced more total angular error and more confusions between left and right. !t is concluded from the research findings that the key to the selection of hearing protectors is to be found in the provision of hearing protectors that can be worn for a very high percentage of the exposure time by a high percentage of the exposed population with the minimum effect on the personal safety of the wearers - the attenuation provided by the protection should be adequate but not a maximum value.

Structural damage identification with noise polluted Frequency Response Functions (FRFs)

Damage detection in structures has become increasingly important in recent years. While a number of damage detection and localization methods have been proposed, very few attempts have been made to explore the structure damage with noise polluted data which is unavoidable effect in real world. The measurement data are contaminated by noise because of test environment as well as electronic devices and this noise tend to give error results with structural damage identification methods. Therefore it is important to investigate a method which can perform better with noise polluted data. This paper introduces a new damage index using principal component analysis (PCA) for damage detection of building structures being able to accept noise polluted frequency response functions (FRFs) as input. The FRF data are obtained from the function datagen of MATLAB program which is available on the web site of the IASC-ASCE (International Association for Structural Control– American Society of Civil Engineers) Structural Health Monitoring (SHM) Task Group. The proposed method involves a five-stage process: calculation of FRFs, calculation of damage index values using proposed algorithm, development of the artificial neural networks and introducing damage indices as input parameters and damage detection of the structure. This paper briefly describes the methodology and the results obtained in detecting damage in all six cases of the benchmark study with different noise levels. The proposed method is applied to a benchmark problem sponsored by the IASC-ASCE Task Group on Structural Health Monitoring, which was developed in order to facilitate the comparison of various damage identification methods. The illustrated results show that the PCA-based algorithm is effective for structural health monitoring with noise polluted FRFs which is of common occurrence when dealing with industrial structures.

Managing intensified urban development and industrial uses in Qld : affected area notations

The Queensland government planning policies actively encourage increased dwelling density, sustainable infill development and transit oriented development to maximise land use and minimise urban sprawl. One of the detriments of such a policy is the potential for intensified residential development to create conflict between lawfully operating existing industrial uses and residences. In particular the government is concerned that intensified urban development will increase the risk of litigation from landowners and tenants detrimentally affected by the emission of aerosols, fumes, light, noise, odour, particles or smoke from existing industrial premises.

A new online secondary path modelling method for feedforward active noise control systems

An online secondary path modelling method using a white noise as a training signal is required in many applications of active noise control (ANC) to ensure convergence of the system. Not continually injection of white noise during system operation makes the system more desirable. The purposes of the proposed method are two folds: controlling white noise by preventing continually injection, and benefiting white noise with a larger variance. The modelling accuracy and the convergence rate increase when a white noise with larger variance is used, however larger the variance increases the residual noise, which decreases performance of the system. This paper proposes a new approach for online secondary path modelling in feedfoward ANC systems. The proposed algorithm uses the advantages of the white noise with larger variance to model the secondary path, but the injection is stopped at the optimum point to increase performance of the system. Comparative simulation results shown in this paper indicate effectiveness of the proposed approach in controlling active noise.

Processing of Ultrasonic Signal for Transducer Characterization and for Improving Signal-To-Noise Ratio

This paper describes the work related to characterisation of an ultrasonic transducer fabricated in the laboratory. The response of the medium to the ultrasonic wave was obtained by converting the time domain signal to frequency domain, using the FFT algorithm. Cross-correlation technique was adopted to increase the S/N ratio in the raw time domain signal and subsequently, to determine the ultrasonic velocity in the medium.

Analysis of a hybrid noise control system for a duct

This letter proposes the combination of a passive muffler and an active noise control system for the control of very high‐level noise in ducts used with large industrial fans and similar equipment. The analysis of such a hybrid system is presented making use of electroacoustic analogies and the transfer matrix method. It turns out that a passive muffler upstream of the input microphone can indeed lower the acoustic pressure and, hence, the power requirement of the auxiliary source. The parameter that needs to be optimized (or maximized) for this purpose is a certain velocity ratio that can readily be evaluated in a closed form, making it more or less straightforward to synthesize the configuration of an effective passive muffler to go with the active noise control system.