Estudos de metais pesados e isótopos de Pb nos sedimentos da Baía de Sepetiba baseados em geoquímica e na distribuição pelas possíveis áreas fontes

A Baia de Sepetiba é uma laguna costeira separada do oceano por uma ilha barreira. Localiza-se a 60 km da cidade do Rio de Janeiro, em uma importante região geoeconômica do Brasil. O objetivo deste trabalho foi avaliar a distribuição espacial da contaminação dos metais Cu, Pb, V, Cr, Cd, Co, Ni e Zn nos sedimentos da Baia. O mapa das concentrações elaborado pelo método de lixiviação permitiu caracterizar anomalias ao entorno da foz do Rio Guandu, na área da Coroa Grande, do Porto de Itaguaí, da Ilha do Martins, e anomalias ao longo de faixa com direção NW-SE. Os resultados das concentrações totais indicam contaminação por Zn, Cd, próximo a Ilha da Madeira com Pb e Cr associados e Cu e Zn na Restinga de Marambaia, com Ni, Pb e Cr associados. Os resultados dos isótopos de Pb para as razões de 206Pb/207Pb entre 1,23 e 1,27 representam os resíduos industriais e ocorrem em duas áreas: na parte leste da Restinga e entre as Ilhas de Jaguanum e Itacuruçá. A leste/sudeste destas ilhas foi reportada uma razão ainda mais alta (1.30), ainda não identificável na literatura. As correntes marinhas desempenham a redistribuição dos sedimentos e metais associados na Baia, com transporte de oeste para leste da pluma sedimentar descarregada pelos rios. Os principais causadores da poluição da Baia de Sepetiba são uma pilha de rejeito de Zn abandonada, resíduos industriais e domésticos não tratados de forma eficaz, poluentes atmosféricos de siderúrgicas e veículos, e por ventura resíduos de atividades navais e militares.

Mutagenic activity of sweepings and pigments from a household-wax factory assayed with Salmonella typhimurium

The mutagenic activity of garbage originating from a household wax industry was determined by the Salmonella/microsome assay, using the bacterial strains TA100, TA98 and YG1024. The garbage was obtained by sweeping the floor of the factory at the end of the work shift. Organic compounds were extracted by ultrasound for 30 min in dichloromethane or 70% ethanol. After evaporation of solvent, these extracts (HFS: household-wax factory sweepings) were dissolved in DMSO, and were tested for the mutagenic activity at varying concentrations (HFS-ET: 0.08-0.68 mg/plate, HFS-DCM: 0.60-7.31 mg/plate). The colouring agents (pigments) used in the production of the wax were also dissolved in DMSO and tested with the assay. The concentrations tested for each pigment were: Amaranth: 0.46-3.65 mg/plate, Auramine: 0.15-1.2 mg/plate, Tartrazine: 0.46-3.65 mg/plate and Rhodamine B: 0.22-1.82 mg/plate. Both ET and DCM organic extracts had mutagenic activity, especially in the YG1024 strain. The pigments behaved in a similar way, demonstrating that YG1024 was the most sensitive strain for the detection of mutagenicity, and that metabolization increased the activity. Human exposure (occupational and non-occupational) to industrial residues generated during the household-wax manufacturing and packaging process should be monitored, since this type of garbage is normally deposited in the environment without any control. (C) 2004 Elsevier Ltd. All rights reserved.

Avaliação da atividade mutagênica do resíduo sólido de uma fábrica de confecções de meias e lingerie em ensaios com Salmonella typhimurium

Cancer is one of the most hazardous effects to human health caused by the exposition to chemical agents. The search for new technological solutions in the industrial field led to a rapid increase in the productive sector, causing the workers to be exposed to millions of potentially toxic agents, substances potentially harmful to health. This study presents the mutagenic activity of sweepings from a sock and lingerie factory in Araraquara-Brazil, assayed with Salmonella typhimurium. All the extracts from the factory had mutagenic on activity the YG1024 strain, which is extremely sensitive to detect the mutagenic activity of the arilhydroxilamines, nitroarenes and aromatic amines. The extracts were non-mutagenics for the strains TA100 and TA98. The analysis of the mutagenicity of industrial residues is highly important because employees that participate in the production are directly exposed to those agents, as well as to the environment where the garbage is deposited.

Estudo da incorporação de cinza e chamote gerado pela cerâmica vermelha ao próprio processo industrial

The ceramics industry generates waste at various stages of that process, defective products, waste from burning solid fuels, among others. This waste is dumped in landfills, garbage dumps or directly on roads, which has a negative environmental impact. This paper presents a study to incorporate the waste of algaroba wood and chamote (scrap pieces of ceramic already sintered), in to the ceramic material for making sealing blocks. The methodological procedures consist in the characterization of chemical and mineralogical residues, raw materials, and physical-mechanical of the formulations of mixes with clay, silt and waste. By pressing test pieces were produced using a pressure of 200 kgf/cm², varying compositions in the range of 0%, 5%, 10% and 15% by weight of residue. The sintering was performed in a muffle furnace, with the temperature levels of 850 ° C, 900 ° C, 950 ° C, 1000 ° C and 1050 ° C. The evaluated physical and mechanical properties were: Water Absorption, Linear Shrinkage Burning, Apparent Porosity, Apparent Density and Mechanical Resistance to Flexion. Analysis was carried out by Scanning Electron Microscopy on fracture surfaces of the specimens. Evaluation of linear shrinkage property drying and firing , water absorption and mechanical resistance to compression of the sealing blocks 5% wood ash residue, sintered at 900 °C hold temperature in the laboratory the products manufactured on an industrial scale. The main results, it was found on the viability of using the residues of algaroba wood and to confer refractory properties of the ceramic product. The main results, it was concluded feasibility of using the ash residues algaroba wood to impart refractory properties to the ceramic product and the residue of chamote, being derived from the own ceramic product not interfere with the properties, when used in a percentage of up to 5%.Since the residue of chamote being derived from the ceramic product itself had no effect on the properties. Studies in the laboratory have shown that the incorporation of up to 5% of these residues may be adopted as an alternative technology to reduce the environmental impact caused by the industrial sector, without compromising the final properties of the material, since the results on an industrial scale showed absorption values 11.66 and 11.74 of water and waste products respectively, within the parameters of NBR - 15,270, since the mechanical strength was 1.25 MPa and 0.94 MPa respectively for products with and without residue, lower than the minimum required by the technical standard that is 1.5 MPa.

Estudo da incorporação de cinza e chamote gerado pela cerâmica vermelha ao próprio processo industrial

The ceramics industry generates waste at various stages of that process, defective products, waste from burning solid fuels, among others. This waste is dumped in landfills, garbage dumps or directly on roads, which has a negative environmental impact. This paper presents a study to incorporate the waste of algaroba wood and chamote (scrap pieces of ceramic already sintered), in to the ceramic material for making sealing blocks. The methodological procedures consist in the characterization of chemical and mineralogical residues, raw materials, and physical-mechanical of the formulations of mixes with clay, silt and waste. By pressing test pieces were produced using a pressure of 200 kgf/cm², varying compositions in the range of 0%, 5%, 10% and 15% by weight of residue. The sintering was performed in a muffle furnace, with the temperature levels of 850 ° C, 900 ° C, 950 ° C, 1000 ° C and 1050 ° C. The evaluated physical and mechanical properties were: Water Absorption, Linear Shrinkage Burning, Apparent Porosity, Apparent Density and Mechanical Resistance to Flexion. Analysis was carried out by Scanning Electron Microscopy on fracture surfaces of the specimens. Evaluation of linear shrinkage property drying and firing , water absorption and mechanical resistance to compression of the sealing blocks 5% wood ash residue, sintered at 900 °C hold temperature in the laboratory the products manufactured on an industrial scale. The main results, it was found on the viability of using the residues of algaroba wood and to confer refractory properties of the ceramic product. The main results, it was concluded feasibility of using the ash residues algaroba wood to impart refractory properties to the ceramic product and the residue of chamote, being derived from the own ceramic product not interfere with the properties, when used in a percentage of up to 5%.Since the residue of chamote being derived from the ceramic product itself had no effect on the properties. Studies in the laboratory have shown that the incorporation of up to 5% of these residues may be adopted as an alternative technology to reduce the environmental impact caused by the industrial sector, without compromising the final properties of the material, since the results on an industrial scale showed absorption values 11.66 and 11.74 of water and waste products respectively, within the parameters of NBR - 15,270, since the mechanical strength was 1.25 MPa and 0.94 MPa respectively for products with and without residue, lower than the minimum required by the technical standard that is 1.5 MPa.

An activity theory framework for industrial design

Ethnography has gained wide acceptance in the industrial design profession and curriculum as a means of understanding the user. However, there is considerable confusion about the particularities of its practice accompanied by the absence of an interoperable vocabulary. The consequent interdisciplinary effort is a power play between disciplines whereby the methodological view of ethnography marginalises its theoretical and analytical components. In doing so, it restricts the potential of ethnography suggesting the need for alternative methods of informing the design process. This article suggests that activity theory, with an emphasis on human activity as the fundamental unit of study, is an appropriate methodology for the generation of user requirements. The process is illustrated through the adaptation of an ethnographic case study, for the design of classroom furniture in India.