Dynamic Tests of a Three-Span Continuous I-Beam Highway Bridge, HR-43, 1959

This paper presents the results of the static and dynamic testing of a three-span continuous I-beam highway bridge. Live load stress frequency curves for selected points are shown, and the static and dynamic load distribution to the longitudinal composite beam members are given. The bridge has four traffic lanes with a roadway width of 48 ft. Six longitudinal continuous WF beams act compositely with the reinforced concrete slab to carry the live load. The beams have partial length cover plates at the piers. Previous research has indicated that beams with partial length cover plates have a very low fatigue strength. It was found in this research that the magnitude of the stresses due to actual highway loads were very much smaller than those computed from specification loading. Also, the larger stresses which were measured occurred a relatively small number of times. These data indicate that some requirements for reduced allowable stresses at the ends of cover plates are too conservative. The load distribution to the longitudinal beams was determined for static and moving loads and includes the effect of impact on the distribution. The effective composite section was found at various locations to evaluate the load distribution data. The composite action was in negative as well as positive moment regions. The load distribution data indicate that the lateral distribution of live load is consistent with the specifications, but that there is longitudinal distribution, and therefore the specifications are too conservative.

Capacity of an I-beam made of S960 QC based on Eurocode 3

The capacity of beams is a very important factor in the study of durability of structures and structural members. The capacity of a high-strength steel I-beam made of S960 QC was investigated in this study. The investigation included assessment of the service limits and ultimate limits of the steel beam. The thesis was done according to European standards for steel structures, Eurocode 3. An analytical method was used to determine the throat thickness, deformation, elastic and plastic moment capacities as well as the fatigue life of the beam. The results of the analytical method were compared with those obtained by Finite Element Analysis (FEA). Elastic moment capacity obtained by the analytical method was 172 kNm. FEA and the analytical method predicted the maximum lateral-torsional buckling (LTB) capacity in the range of 90-93 kNm and the probability of failure as a result of LTB is estimated to be 50%. The lateral buckling capacity meant that the I-beam can carry a safe load of 300 kN instead of the initial load of 600 kN. The beam is liable to fail shortly after exceeding the elastic moment capacity. Based on results in of the different approaches, it was noted that FEA predicted higher deformation values on the load-deformation curve than the analytical results. However, both FEA and the analytical methods predicted identical results for nominal stress range and moment capacities. Fatigue life was estimated to be in the range of 53000-64000 cycles for bending stress range using crack propagation equation and strength-life approach. As Eurocode 3 is limited to steel grades up to S690, results for S960 must be verified with experimental data and appropriate design rules.

End connections of pretensioned I-beam bridges.

Mode of access: Internet.

Feasibility Study of Strengthening Existing Single Span Steel Beam Concrete Deck Bridges, June 1961

Iowa has the same problem that confronts most states in the United States: many bridges constructed more than 20 years ago either have deteriorated to the point that they are inadequate for original design loads or have been rendered inadequate by changes in design/maintenance standards or design loads. Inadequate bridges require either strengthening or posting for reduced loads. A sizeable number of single span, composite concrete deck - steel I beam bridges in Iowa currently cannot be rated to carry today's design loads. Various methods for strengthening the unsafe bridges have been proposed and some methods have been tried. No method appears to be as economical and promising as strengthening by post-tensioning of the steel beams. At the time this research study was begun, the feasibility of posttensioning existing composite bridges was unknown. As one would expect, the design of a bridge-strengthening scheme utilizing post-tensioning is quite complex. The design involves composite construction stressed in an abnormal manner (possible tension in the deck slab), consideration of different sizes of exterior and interior beams, cover-plated beams already designed for maximum moment at midspan and at plate cut-off points, complex live load distribution, and distribution of post-tensioningforces and moments among the bridge beams. Although information is available on many of these topics, there is miminal information on several of them and no information available on the total design problem. This study, therefore, is an effort to gather some of the missing information, primarily through testing a half-size bridge model and thus determining the feasibility of strengthening composite bridges by post-tensioning. Based on the results of this study, the authors anticipate that a second phase of the study will be undertaken and directed toward strengthening of one or more prototype bridges in Iowa.

S960 QC teräksisen I-palkin äärikestävyyden määrittäminen

Tämän työn tavoitteena oli selvittää eurooppalaisen teräsrakenteiden suunniteltustandardin, Eurokoodi 3:n, soveltuvuus ultralujille teräksille. Tällä hetkellä kyseinen standardi pitää sisällään teräslajit vain S700-teräslajiin asti. Tässä kandidaatintyössä selvitettiin S960 QC –teräksisen I-palkin äärikestävyys ja tarkasteltiin nykyisten suunnitteluohjeiden paikkansapitävyyttä.

Retrofit Methods for Distortion Cracking Problems in Plate Girder Bridges, TR-436, 2003

This report is formatted to independently present four individual investigations related to similar web gap fatigue problems. Multiple steel girder bridges commonly exhibit fatigue cracking due to out-of-plane displacement of the web near the diaphragm connections. This fatigue-prone web gap area is typically located in negative moment regions of the girders where the diaphragm stiffener is not attached to the top flange. In the past, the Iowa Department of Transportation has attempted to stop fatigue crack propagation in these steel girder bridges by drilling holes at the crack tips. Other nondestructive retrofits have been tried; in a particular case on a two-girder bridge with floor beams, angles were bolted between the stiffener and top flange. The bolted angle retrofit has failed in the past and may not be a viable solution for diaphragm bridges. The drilled hole retrofit is often only a temporary solution, so a more permanent and effective retrofit is required. A new field retrofit has been developed that involves loosening the bolts in the connection between the diaphragm and the girders. Research on the retrofit has been initiated; however, no long-term studies of the effects of bolt loosening have been performed. The intent of this research is to study the short-term effects of the bolt loosening retrofit on I-beam and channel diaphragm bridges. The research also addressed the development of a continuous remote monitoring system to investigate the bolt loosening retrofit on an X-type diaphragm bridge over a number of months, ensuring that the measured strain and displacement reductions are not affected by time and continuous traffic loading on the bridge. The testing for the first three investigations is based on instrumentation of web gaps in a negative moment region on Iowa Department of Transportation bridges with I-beam, channel, and X-type diaphragms. One bridge of each type was instrumented with strain gages and deflection transducers. Field tests, using loaded trucks of known weight and configuration, were conducted on the bridges with the bolts in the tight condition and after implementing the bolt loosening retrofit to measure the effects of loosening the diaphragm bolts. Long-term data were also collected on the X-diaphragm bridge by a data acquisition system that collected the data continuously under ambient truck loading. The collected data were retrievable by an off-site modem connection to the remote data acquisition system. The data collection features and ruggedness of this system for remote bridge monitoring make it viable as a pilot system for future monitoring projects in Iowa. Results indicate that loosening the diaphragm bolts reduces strain and out-of-plane displacement in the web gap, and that the reduction is not affected over time by traffic or environmental loading on the bridge. Reducing the strain in the web gap allows the bridge to support more cycles of loading before experiencing fatigue, thus increase the service life of the bridge. Two-girder floor beam bridges may also exhibit fatigue cracking in girder webs.

Ontologies and Methods for Interoperability of Engineering Analysis Models (EAMS) in an E-Design Environment

ABSTRACT ONTOLOGIES AND METHODS FOR INTEROPERABILITY OF ENGINEERING ANALYSIS MODELS (EAMS) IN AN E-DESIGN ENVIRONMENT SEPTEMBER 2007 NEELIMA KANURI, B.S., BIRLA INSTITUTE OF TECHNOLOGY AND SCIENCES PILANI INDIA M.S., UNIVERSITY OF MASSACHUSETTS AMHERST Directed by: Professor Ian Grosse Interoperability is the ability of two or more systems to exchange and reuse information efficiently. This thesis presents new techniques for interoperating engineering tools using ontologies as the basis for representing, visualizing, reasoning about, and securely exchanging abstract engineering knowledge between software systems. The specific engineering domain that is the primary focus of this report is the modeling knowledge associated with the development of engineering analysis models (EAMs). This abstract modeling knowledge has been used to support integration of analysis and optimization tools in iSIGHT FD , a commercial engineering environment. ANSYS , a commercial FEA tool, has been wrapped as an analysis service available inside of iSIGHT-FD. Engineering analysis modeling (EAM) ontology has been developed and instantiated to form a knowledge base for representing analysis modeling knowledge. The instances of the knowledge base are the analysis models of real world applications. To illustrate how abstract modeling knowledge can be exploited for useful purposes, a cantilever I-Beam design optimization problem has been used as a test bed proof-of-concept application. Two distinct finite element models of the I-beam are available to analyze a given beam design- a beam-element finite element model with potentially lower accuracy but significantly reduced computational costs and a high fidelity, high cost, shell-element finite element model. The goal is to obtain an optimized I-beam design at minimum computational expense. An intelligent KB tool was developed and implemented in FiPER . This tool reasons about the modeling knowledge to intelligently shift between the beam and the shell element models during an optimization process to select the best analysis model for a given optimization design state. In addition to improved interoperability and design optimization, methods are developed and presented that demonstrate the ability to operate on ontological knowledge bases to perform important engineering tasks. One such method is the automatic technical report generation method which converts the modeling knowledge associated with an analysis model to a flat technical report. The second method is a secure knowledge sharing method which allocates permissions to portions of knowledge to control knowledge access and sharing. Both the methods acting together enable recipient specific fine grain controlled knowledge viewing and sharing in an engineering workflow integration environment, such as iSIGHT-FD. These methods together play a very efficient role in reducing the large scale inefficiencies existing in current product design and development cycles due to poor knowledge sharing and reuse between people and software engineering tools. This work is a significant advance in both understanding and application of integration of knowledge in a distributed engineering design framework.

Nuevo concepto de elementos estructurales horizontales de vidrio : placa autoportante y pretensada en forma de pi

En los últimos años, podemos darnos cuenta de la importancia que tienen las nuevas aplicaciones de vidrio especialmente en edificios turísticos donde el vértigo juega un papel importante en la visita. Sin embargo los sistemas constructivos no tienen un especial interés porque el vidrio laminado está siempre soportado por otro elemento de acero o incluso vidrio en forma de retícula. En la presente tesis voy a desarrollar una nueva solución de elemento autoportante de vidrio de gran tamaño haciendo seguro el uso del elemento para andar en el aire. El sueño de muchos arquitectos ha sido diseñar un edificio completamente transparente y a mí me gustaría contribuir a este sueño empezando a estudiar un forjado de vidrio como elemento estructural horizontal y para ello debemos cumplir requerimientos de seguridad. Uno de los objetivos es lograr un elemento lo más transparente y esbelto posible para el uso de pasarelas en vestíbulos de edificios. Las referencias construidas son bien conocidas, pero por otro lado Universidades europeas estudian continua estudiando el comportamiento del vidrio con diferentes láminas, adhesivos, apilados, insertos, sistemas de laminado, pretensado, pandeo lateral, seguridad post-rotura y muchos más aspectos necesarios. La metodología llevada a cabo en esta tesis ha sido primeramente diseñar un elemento industrial prefabricado horizontal de vidrio teniendo en cuenta todos los conceptos aprendidos en el estado del arte y la investigación para poder predimensionar el elemento. El siguiente paso será verificar el modelo por medio de cálculo analítico, simulación de elementos finitos y ensayos físicos. Para realizar los ensayos hay un paso intermedio teniendo que cambiar la hipótesis de carga uniforme a carga puntal para realizar el ensayo de flexión a 4 puntos normalizado y además cambiar a escala 1:2 para adaptarse al espacio de ensayo y ser viable económicamente. Finalmente compararé los resultados de tensión y deformación obtenidos por los tres métodos para extraer conclusiones. Sin embargo el problema de la seguridad no ha concluido, tendré que demostrar que el sistema es seguro después de que se produzca la rotura y para ello sólo dispongo de los ensayos como medio de demostración. El diseño es el resultado de la evolución de una viga tipo “I”; cuando es pretensada para obtener más resistencia, aparece el problema de pandeo lateral y éste es solucionado con una viga con sección en “T” cuya unión es resuelta con un cajeado longitudinal en la parte inferior del elemento horizontal. Las alas de éste crecen para recoger las cargas superficiales creando a su vez un punto débil en la unión que a su vez se soluciona duplicando la sección “TT” y haciendo trabajar dicho tablero de forma tan óptima como una viga continua. Dicha sección en vidrio como un único elemento pretensado es algo inédito. Además he diseñado unas escuadras metálicas en los extremos de los nervios como apoyo y placa de pretensión, así como una hendidura curva en el centro de los nervios para alojar los tirantes de acero de modo que al pretensar el tirante la placa corrija al menos la deformación por peso propio. Realizados los cambios geométricos de escala y las simplificaciones en el laminado y el adhesivo se programan la extracción de resultados desde 3 estadios diferentes: Sin pretensión y con pretensión de 750 Kg y de 1000Kg en cada nervio. Por cada estadio y por cada uno de los métodos, cálculo, simulación y ensayos, se extraen los datos de deformación y tensión en el punto medio de un nervio con el objetivo de hacer una comparación de resultados para obtener unas conclusiones, siempre en el campo de la elasticidad. Posteriormente incrementaré la carga hasta el momento de la rotura de la placa y después hasta el colapso teniendo en cuenta el tiempo y demostrando una rotura segura. El vidrio no tendrá un comportamiento plástico pero habrá sido controlado su comportamiento frágil manteniendo una carga y una deformación aceptable. ABSTRACT Over the past few years we have realized the importance of the new technologies regarding the application of glass in new buildings, especially those touristic places were the views and the heights are the reason of the visit. However, the construction systems of these glass platforms are not usually as interesting, because the laminated glass is always held by another steel substructure or even a grid-formed glass element. Throughout this thesis I am going to develop a new solution of a self-bearing element with big dimensions made out of glass, ensuring a safe solution to use as an element to walk on the air. The dream of many architects has been to create a building completely transparent, and I would like to contribute to this idea by making a glass slab as a horizontal structural element, for which we have to meet the security requirements. One of the goals is to achieve an element as transparent and slim as possible for the use in walkways of building lobbies. The glass buildings references are well known, but on the other hand the European Universities study the behaviour of the glass with different interlayers, adhesives, laminating systems, stacking, prestressed, buckling, safety, breakage and post-breakage capacity; and many other necessary aspects. The methodology followed in this thesis has been to first create a horizontal industrial prefabricated horizontal element of glass, taking into account all the concepts learned in the state of art and the investigation to be able to predimension this element. The next step will be to verify this model with an analytic calculus, a finite element modelling simulation and physical tests. To fulfil these tests there is an intermediate step, having to change the load hypothesis from a punctual one to make the test with a four points normalized deflexion, and also the scale of the sample was changed to 1:2 to adapt to the space of the test and make it economically possible. Finally, the results of tension and deformation obtained from the three methods have been compared to make the conclusions. However, the problem with safety has not concluded yet, for I will have to demonstrate that this system is safe even after its breakage, for which I can only use physical tests as a way of demonstration. The design is the result of the evolution of a typical “I” beam, which when it is prestressed to achieve more resistance, the effect of buckling overcomes, and this is solved with a “T” shaped beam, where the union is solved with a longitudinal groove on the inferior part of the horizontal element. The boards of this beam grow to cover the superficial loads, creating at the same time a weak point, which is solved by duplicating the section “TT” and therefore making this board work as optimal as a continuous beam. This glass section as a single prestressed element is unique. After the final design of the “π” glass plate was obtained and the composition of the laminated glass and interlayers has been predimensioned, the last connection elements must be contemplated. I have also designed a square steel shoe at the end of the beams, which will be the base and the prestressed board, as well as a curved slot in the centre of the nerves to accommodate the steel braces so that when this brace prestresses the board, at least the deformation due to its self-weight will be amended. Once I made the geometric changes of the scale and the simplifications on the laminating and the adhesive, the extraction on results overcomes from three different stages: without any pretension, with a pretension of 750 kg and with a pretension of 1000 kg on each rib. For each stage and for each one of the methods, calculus, simulation and tests, the deformation datum were extracted to obtain the conclusions, always in the field of the elasticity. Afterwards, I will increase the load until the moment of breakage of this board, and then until the collapse of the element, taking into account the time spent and demonstrating a safe breakage. The glass will not have a plastic behaviour, but its brittle behaviour has been controlled, keeping an acceptable load and deflection.

Debonding and crack propagation in cracked steel beams strengthened with CFRP and subjected to cyclic loads.

The reinforcement methods used to restore or increase the bearing capacity of metal structures are based on the application of steel plates to be bolted or welded to the original structure, which can cause problems to the integrity of the original structure. These difficulties can be overcome with the introduction of fiber-reinforced composite materials. FRPs are characterized by high strength to weight ratio, and they are very resistant to corrosion. In this dissertation a cracked steel I-beam reinforced with Carbon Fiber-Reinforced Polymer will be studied by performing a numerical evaluation of the structure with the commercial Finite Element Method software ABAQUS. The crack propagation will be computed using XFEM, while the debonding of the reinforcement layer will be found by considering a cohesive contact interface between the beam and the CFRP plate. The results will show the efficiency of the strengthening method in increasing the load carrying capacity of the cracked beam, and in reducing the crack opening of the initial notch.

Cone-beam evaluation of pharyngeal airway space in class I, II, and III patients

The purpose of this study is to make a 3-dimensional (3-D) evaluation of the pharyngeal airway space (PAS) in patients with class I, II, and III malocclusion. Sixty patients were evaluated. The patients were divided in 3 groups according to their occlusion classification. The volume and area of PAS were evaluated using the software Dolphin 3-D Imaging in the preoperative period for orthognathic surgery. PAS volume and area were influenced by different patterns of malocclusion. The mean volume and area for class III patients were statistically bigger than for classes I and II patients (P < .001). There was also a significant difference for volume values between class I and II patients, being the bigger volume for the class I patients (P < .05). It was possible to conclude that the class III patients presented a bigger PAS compared with classes I and II patients.

Beam-energy Dependence Of The Directed Flow Of Protons, Antiprotons, And Pions In Au+au Collisions.

Rapidity-odd directed flow (v1) measurements for charged pions, protons, and antiprotons near midrapidity (y=0) are reported in sNN=7.7, 11.5, 19.6, 27, 39, 62.4, and 200 GeV Au+Au collisions as recorded by the STAR detector at the Relativistic Heavy Ion Collider. At intermediate impact parameters, the proton and net-proton slope parameter dv1/dy|y=0 shows a minimum between 11.5 and 19.6 GeV. In addition, the net-proton dv1/dy|y=0 changes sign twice between 7.7 and 39 GeV. The proton and net-proton results qualitatively resemble predictions of a hydrodynamic model with a first-order phase transition from hadronic matter to deconfined matter, and differ from hadronic transport calculations.

Beam-energy Dependence Of Charge Separation Along The Magnetic Field In Au+au Collisions At Rhic.

Local parity-odd domains are theorized to form inside a quark-gluon plasma which has been produced in high-energy heavy-ion collisions. The local parity-odd domains manifest themselves as charge separation along the magnetic field axis via the chiral magnetic effect. The experimental observation of charge separation has previously been reported for heavy-ion collisions at the top RHIC energies. In this Letter, we present the results of the beam-energy dependence of the charge correlations in Au+Au collisions at midrapidity for center-of-mass energies of 7.7, 11.5, 19.6, 27, 39, and 62.4 GeV from the STAR experiment. After background subtraction, the signal gradually reduces with decreased beam energy and tends to vanish by 7.7 GeV. This implies the dominance of hadronic interactions over partonic ones at lower collision energies.

Beam Energy Dependence Of Moments Of The Net-charge Multiplicity Distributions In Au+au Collisions At Rhic.

We report the first measurements of the moments--mean (M), variance (σ(2)), skewness (S), and kurtosis (κ)--of the net-charge multiplicity distributions at midrapidity in Au+Au collisions at seven energies, ranging from sqrt[sNN]=7.7 to 200 GeV, as a part of the Beam Energy Scan program at RHIC. The moments are related to the thermodynamic susceptibilities of net charge, and are sensitive to the location of the QCD critical point. We compare the products of the moments, σ(2)/M, Sσ, and κσ(2), with the expectations from Poisson and negative binomial distributions (NBDs). The Sσ values deviate from the Poisson baseline and are close to the NBD baseline, while the κσ(2) values tend to lie between the two. Within the present uncertainties, our data do not show nonmonotonic behavior as a function of collision energy. These measurements provide a valuable tool to extract the freeze-out parameters in heavy-ion collisions by comparing with theoretical models.

Vertical Bone Measurements From Cone Beam Computed Tomography Images Using Different Software Packages.

This article aimed at comparing the accuracy of linear measurement tools of different commercial software packages. Eight fully edentulous dry mandibles were selected for this study. Incisor, canine, premolar, first molar and second molar regions were selected. Cone beam computed tomography (CBCT) images were obtained with i-CAT Next Generation. Linear bone measurements were performed by one observer on the cross-sectional images using three different software packages: XoranCat®, OnDemand3D® and KDIS3D®, all able to assess DICOM images. In addition, 25% of the sample was reevaluated for the purpose of reproducibility. The mandibles were sectioned to obtain the gold standard for each region. Intraclass coefficients (ICC) were calculated to examine the agreement between the two periods of evaluation; the one-way analysis of variance performed with the post-hoc Dunnett test was used to compare each of the software-derived measurements with the gold standard. The ICC values were excellent for all software packages. The least difference between the software-derived measurements and the gold standard was obtained with the OnDemand3D and KDIS3D (-0.11 and -0.14 mm, respectively), and the greatest, with the XoranCAT (+0.25 mm). However, there was no statistical significant difference between the measurements obtained with the different software packages and the gold standard (p> 0.05). In conclusion, linear bone measurements were not influenced by the software package used to reconstruct the image from CBCT DICOM data.

Reprodutibilidade das mensurações da espessura das tábuas ósseas na tomografia computadorizada Cone-Beam utilizando diferentes protocolos de aquisição de imagem

INTRODUÇÃO: quanto menor a dimensão do voxel, maior a nitidez da imagem de tomografia computadorizada Cone-Beam (TCCB), porém, maior a dose de radiação emitida. OBJETIVOS: avaliar e comparar a reprodutibilidade da mensuração da espessura das tábuas ósseas vestibular e lingual em imagens de TCCB, utilizando diferentes protocolos de aquisição de imagem com variação da dimensão do voxel. MÉTODOS: exames de TCCB foram tomados de 12 mandíbulas humanas secas, com dimensão do voxel de 0,2; 0,3 e 0,4mm, no aparelho i-CAT Cone-Beam 3-D Dental Imaging System. No software i-CAT Viewer, foi mensurada a espessura das tábuas ósseas vestibular e lingual, em um corte axial passando 12mm acima do forame mentoniano do lado direito. A reprodutibilidade intraexaminador foi avaliada por meio da aplicação do teste t pareado. Para a comparação interexaminadores, foi utilizado o teste t independente. Os resultados foram considerados com o nível de significância de 5%. RESULTADOS: observou-se uma excelente reprodutibilidade interexaminadores para os três protocolos avaliados. A reprodutibilidade intraexaminadores foi muito boa, com exceção de algumas regiões dos dentes anteriores, que mostraram diferenças estatisticamente significativas, independentemente da dimensão do voxel. CONCLUSÃO: a mensuração da espessura das tábuas ósseas vestibular e lingual em imagens de TCCB mostrou boa precisão para exames obtidos com voxel de 0,2; 0,3 ou 0,4mm. A reprodutibilidade das mensurações na região anterior da mandíbula foi mais crítica do que na região posterior.