Comparison of time-lapse GPR data collected under natural and forced infiltration conditions to estimate vadose zone hydraulic parameters

Time-lapse crosshole ground-penetrating radar (GPR) data, collected while infiltration occurs, can provide valuable information regarding the hydraulic properties of the unsaturated zone. In particular, the stochastic inversion of such data provides estimates of parameter uncertainties, which are necessary for hydrological prediction and decision making. Here, we investigate the effect of different infiltration conditions on the stochastic inversion of time-lapse, zero-offset-profile, GPR data. Inversions are performed using a Bayesian Markov-chain-Monte-Carlo methodology. Our results clearly indicate that considering data collected during a forced infiltration test helps to better refine soil hydraulic properties compared to data collected under natural infiltration conditions

Alternative Analytical Expressions for the General van Genuchten-Mualem and van Genuchten-Burdine Hydraulic Conductivity Models

The van Genuchten expressions for the unsaturated soil hydraulic properties, first published in 1980, are used frequently in various vadose zone flow and transport applications assuming a specific relationship between the m and n soil hydraulic parameters. By comparison, probably because of the complexity of the hydraulic conductivity equations, the more general solutions with independent m and n values are rarely used. We expressed the general van Genuchten-Mualem and van Genuchten-Burdine hydraulic conductivity equations in terms of hypergeometric functions, which can be approximated by infinite series that converge rapidly for relatively large values of the van Genuchten-Mualem parameter n but only very slowly when n is close to one. Alternative equations were derived that provide very close approximations of the analytical results. The newly proposed equations allow the use of independent values of the parameters m and n in the soil water retention model of van Genuchten for subsequent prediction of the van Genuchten-Mualem and van Genuchten-Burdine hydraulic conductivity models, thus providing more flexibility in fitting experimental pressure-head-dependent water content, theta(h), and hydraulic conductivity, K(h), or K(theta) data.

Quantitative integration of geophysical and hydraulic data : from the local towards the regional scale range

Des progrès significatifs ont été réalisés dans le domaine de l'intégration quantitative des données géophysique et hydrologique l'échelle locale. Cependant, l'extension à de plus grandes échelles des approches correspondantes constitue encore un défi majeur. Il est néanmoins extrêmement important de relever ce défi pour développer des modèles fiables de flux des eaux souterraines et de transport de contaminant. Pour résoudre ce problème, j'ai développé une technique d'intégration des données hydrogéophysiques basée sur une procédure bayésienne de simulation séquentielle en deux étapes. Cette procédure vise des problèmes à plus grande échelle. L'objectif est de simuler la distribution d'un paramètre hydraulique cible à partir, d'une part, de mesures d'un paramètre géophysique pertinent qui couvrent l'espace de manière exhaustive, mais avec une faible résolution (spatiale) et, d'autre part, de mesures locales de très haute résolution des mêmes paramètres géophysique et hydraulique. Pour cela, mon algorithme lie dans un premier temps les données géophysiques de faible et de haute résolution à travers une procédure de réduction déchelle. Les données géophysiques régionales réduites sont ensuite reliées au champ du paramètre hydraulique à haute résolution. J'illustre d'abord l'application de cette nouvelle approche dintégration des données à une base de données synthétiques réaliste. Celle-ci est constituée de mesures de conductivité hydraulique et électrique de haute résolution réalisées dans les mêmes forages ainsi que destimations des conductivités électriques obtenues à partir de mesures de tomographic de résistivité électrique (ERT) sur l'ensemble de l'espace. Ces dernières mesures ont une faible résolution spatiale. La viabilité globale de cette méthode est testée en effectuant les simulations de flux et de transport au travers du modèle original du champ de conductivité hydraulique ainsi que du modèle simulé. Les simulations sont alors comparées. Les résultats obtenus indiquent que la procédure dintégration des données proposée permet d'obtenir des estimations de la conductivité en adéquation avec la structure à grande échelle ainsi que des predictions fiables des caractéristiques de transports sur des distances de moyenne à grande échelle. Les résultats correspondant au scénario de terrain indiquent que l'approche d'intégration des données nouvellement mise au point est capable d'appréhender correctement les hétérogénéitées à petite échelle aussi bien que les tendances à gande échelle du champ hydraulique prévalent. Les résultats montrent également une flexibilté remarquable et une robustesse de cette nouvelle approche dintégration des données. De ce fait, elle est susceptible d'être appliquée à un large éventail de données géophysiques et hydrologiques, à toutes les gammes déchelles. Dans la deuxième partie de ma thèse, j'évalue en détail la viabilité du réechantillonnage geostatique séquentiel comme mécanisme de proposition pour les méthodes Markov Chain Monte Carlo (MCMC) appliquées à des probmes inverses géophysiques et hydrologiques de grande dimension . L'objectif est de permettre une quantification plus précise et plus réaliste des incertitudes associées aux modèles obtenus. En considérant une série dexemples de tomographic radar puits à puits, j'étudie deux classes de stratégies de rééchantillonnage spatial en considérant leur habilité à générer efficacement et précisément des réalisations de la distribution postérieure bayésienne. Les résultats obtenus montrent que, malgré sa popularité, le réechantillonnage séquentiel est plutôt inefficace à générer des échantillons postérieurs indépendants pour des études de cas synthétiques réalistes, notamment pour le cas assez communs et importants où il existe de fortes corrélations spatiales entre le modèle et les paramètres. Pour résoudre ce problème, j'ai développé un nouvelle approche de perturbation basée sur une déformation progressive. Cette approche est flexible en ce qui concerne le nombre de paramètres du modèle et lintensité de la perturbation. Par rapport au rééchantillonage séquentiel, cette nouvelle approche s'avère être très efficace pour diminuer le nombre requis d'itérations pour générer des échantillons indépendants à partir de la distribution postérieure bayésienne. - Significant progress has been made with regard to the quantitative integration of geophysical and hydrological data at the local scale. However, extending corresponding approaches beyond the local scale still represents a major challenge, yet is critically important for the development of reliable groundwater flow and contaminant transport models. To address this issue, I have developed a hydrogeophysical data integration technique based on a two-step Bayesian sequential simulation procedure that is specifically targeted towards larger-scale problems. The objective is to simulate the distribution of a target hydraulic parameter based on spatially exhaustive, but poorly resolved, measurements of a pertinent geophysical parameter and locally highly resolved, but spatially sparse, measurements of the considered geophysical and hydraulic parameters. To this end, my algorithm links the low- and high-resolution geophysical data via a downscaling procedure before relating the downscaled regional-scale geophysical data to the high-resolution hydraulic parameter field. I first illustrate the application of this novel data integration approach to a realistic synthetic database consisting of collocated high-resolution borehole measurements of the hydraulic and electrical conductivities and spatially exhaustive, low-resolution electrical conductivity estimates obtained from electrical resistivity tomography (ERT). The overall viability of this method is tested and verified by performing and comparing flow and transport simulations through the original and simulated hydraulic conductivity fields. The corresponding results indicate that the proposed data integration procedure does indeed allow for obtaining faithful estimates of the larger-scale hydraulic conductivity structure and reliable predictions of the transport characteristics over medium- to regional-scale distances. The approach is then applied to a corresponding field scenario consisting of collocated high- resolution measurements of the electrical conductivity, as measured using a cone penetrometer testing (CPT) system, and the hydraulic conductivity, as estimated from electromagnetic flowmeter and slug test measurements, in combination with spatially exhaustive low-resolution electrical conductivity estimates obtained from surface-based electrical resistivity tomography (ERT). The corresponding results indicate that the newly developed data integration approach is indeed capable of adequately capturing both the small-scale heterogeneity as well as the larger-scale trend of the prevailing hydraulic conductivity field. The results also indicate that this novel data integration approach is remarkably flexible and robust and hence can be expected to be applicable to a wide range of geophysical and hydrological data at all scale ranges. In the second part of my thesis, I evaluate in detail the viability of sequential geostatistical resampling as a proposal mechanism for Markov Chain Monte Carlo (MCMC) methods applied to high-dimensional geophysical and hydrological inverse problems in order to allow for a more accurate and realistic quantification of the uncertainty associated with the thus inferred models. Focusing on a series of pertinent crosshole georadar tomographic examples, I investigated two classes of geostatistical resampling strategies with regard to their ability to efficiently and accurately generate independent realizations from the Bayesian posterior distribution. The corresponding results indicate that, despite its popularity, sequential resampling is rather inefficient at drawing independent posterior samples for realistic synthetic case studies, notably for the practically common and important scenario of pronounced spatial correlation between model parameters. To address this issue, I have developed a new gradual-deformation-based perturbation approach, which is flexible with regard to the number of model parameters as well as the perturbation strength. Compared to sequential resampling, this newly proposed approach was proven to be highly effective in decreasing the number of iterations required for drawing independent samples from the Bayesian posterior distribution.

Determination of hydraulic properties of a tropical soil of Hawaii using column experiments and inverse modeling

A method for determining soil hydraulic properties of a weathered tropical soil (Oxisol) using a medium-sized column with undisturbed soil is presented. The method was used to determine fitting parameters of the water retention curve and hydraulic conductivity functions of a soil column in support of a pesticide leaching study. The soil column was extracted from a continuously-used research plot in Central Oahu (Hawaii, USA) and its internal structure was examined by computed tomography. The experiment was based on tension infiltration into the soil column with free outflow at the lower end. Water flow through the soil core was mathematically modeled using a computer code that numerically solves the one-dimensional Richards equation. Measured soil hydraulic parameters were used for direct simulation, and the retention and soil hydraulic parameters were estimated by inverse modeling. The inverse modeling produced very good agreement between model outputs and measured flux and pressure head data for the relatively homogeneous column. The moisture content at a given pressure from the retention curve measured directly in small soil samples was lower than that obtained through parameter optimization based on experiments using a medium-sized undisturbed soil column.

Estimating vadose zone hydraulic properties using ground penetrating radar: The impact of prior information

A number of geophysical methods, such as ground-penetrating radar (GPR), have the potential to provide valuable information on hydrological properties in the unsaturated zone. In particular, the stochastic inversion of such data within a coupled geophysical-hydrological framework may allow for the effective estimation of vadose zone hydraulic parameters and their corresponding uncertainties. A critical issue in stochastic inversion is choosing prior parameter probability distributions from which potential model configurations are drawn and tested against observed data. A well chosen prior should reflect as honestly as possible the initial state of knowledge regarding the parameters and be neither overly specific nor too conservative. In a Bayesian context, combining the prior with available data yields a posterior state of knowledge about the parameters, which can then be used statistically for predictions and risk assessment. Here we investigate the influence of prior information regarding the van Genuchten-Mualem (VGM) parameters, which describe vadose zone hydraulic properties, on the stochastic inversion of crosshole GPR data collected under steady state, natural-loading conditions. We do this using a Bayesian Markov chain Monte Carlo (MCMC) inversion approach, considering first noninformative uniform prior distributions and then more informative priors derived from soil property databases. For the informative priors, we further explore the effect of including information regarding parameter correlation. Analysis of both synthetic and field data indicates that the geophysical data alone contain valuable information regarding the VGM parameters. However, significantly better results are obtained when we combine these data with a realistic, informative prior.

Bayesian-MCMC inversion of time-lapse geophysical data to characterize vadose zone hydraulic behaviour

Geophysical methods have the potential to provide valuable information on hydrological properties in the unsaturated zone. In particular, time-lapse geophysical data, when coupled with a hydrological model and inverted stochastically, may allow for the effective estimation of subsurface hydraulic parameters and their corresponding uncertainties. In this study, we use a Bayesian Markov-chain-Monte-Carlo (MCMC) inversion approach to investigate how much information regarding vadose zone hydraulic properties can be retrieved from time-lapse crosshole GPR data collected at the Arrenaes field site in Denmark during a forced infiltration experiment.

Influence of vegetation on the local climate and hydrology in the tropics: sensitivity to soil parameters

Land use change with accompanying major modifications to the vegetation cover is widespread in the tropics, due to increasing demands for agricultural land, and may have significant impacts on the climate. This study investigates (1) the influence of vegetation on the local climate in the tropics; (2) how that influence varies from region to region; and (3) how the sensitivity of the local climate to vegetation, and hence land use change, depends on the hydraulic characteristics of the soil. A series of idealised experiments with the Hadley Centre atmospheric model, HadAM3, are described in which the influence of vegetation in the tropics is assessed by comparing the results of integrations with and without tropical vegetation. The sensitivity of the results to the soil characteristics is then explored by repeating the experiments with a differing, but equally valid, description of soil hydraulic parameters. The results have shown that vegetation has a significant moderating effect on the climate throughout the tropics by cooling the surface through enhanced latent heat fluxes. The influence of vegetation is, however, seasonally dependent, with much greater impacts during the dry season when the availability of surface moisture is limited. Furthermore, there are significant regional variations both in terms of the magnitude of the cooling and in the response of the precipitation. Not all regions show a feedback of vegetation on the local precipitation; this result has been related both to vegetation type and to the prevailing meteorological conditions. An important finding has been the sensitivity of the results to the specification of the soil hydraulic parameters. The introduction of more freely draining soils has changed the soil-moisture contents of the control, vegetated system and has reduced, significantly, the climate sensitivity to vegetation and by implication, land use change. Changes to the soil parameters have also had an impact on the soil hydrology and its interaction with vegetation, by altering the partitioning between fast and slow runoff processes. These results raise important questions about the representation of highly heterogeneous soil characteristics in climate models, as well as the potential influence of land use change on the soil characteristics themselves.

Modeling plant transpiration under limited soil water: comparison of different plant and soil hydraulic parameterizations and preliminary implications for their use in land surface models

Accurate estimates of how soil water stress affects plant transpiration are crucial for reliable land surface model (LSM) predictions. Current LSMs generally use a water stress factor, β, dependent on soil moisture content, θ, that ranges linearly between β = 1 for unstressed vegetation and β = 0 when wilting point is reached. This paper explores the feasibility of replacing the current approach with equations that use soil water potential as their independent variable, or with a set of equations that involve hydraulic and chemical signaling, thereby ensuring feedbacks between the entire soil–root–xylem–leaf system. A comparison with the original linear θ-based water stress parameterization, and with its improved curvi-linear version, was conducted. Assessment of model suitability was focused on their ability to simulate the correct (as derived from experimental data) curve shape of relative transpiration versus fraction of transpirable soil water. We used model sensitivity analyses under progressive soil drying conditions, employing two commonly used approaches to calculate water retention and hydraulic conductivity curves. Furthermore, for each of these hydraulic parameterizations we used two different parameter sets, for 3 soil texture types; a total of 12 soil hydraulic permutations. Results showed that the resulting transpiration reduction functions (TRFs) varied considerably among the models. The fact that soil hydraulic conductivity played a major role in the model that involved hydraulic and chemical signaling led to unrealistic values of β, and hence TRF, for many soil hydraulic parameter sets. However, this model is much better equipped to simulate the behavior of different plant species. Based on these findings, we only recommend implementation of this approach into LSMs if great care with choice of soil hydraulic parameters is taken

Interactions between roughness and topography in hydraulic models

Analysis of river flow using hydraulic modelling and its implications in derived environ-mental applications are inextricably connected with the way in which the river boundary shape is represented. This relationship is scale-dependent upon the modelling resolution which in turn determines the importance of a subscale performance of the model and the way subscale (surface and flow) processes are parameterised. Commonly, the subscale behaviour of the model relies upon a roughness parameterisation whose meaning depends on the dimensionality of the hydraulic model and the resolution of the topographic represen¬tation scale. This latter is, in turn, dependent on the resolution of the computational mesh as well as on the detail of measured topographic data. Flow results are affected by this interactions between scale and subscale parameterisation according to the dimensionality approach. The aim of this dissertation is the evaluation of these interactions upon hy¬draulic modelling results. Current high resolution topographic source availability induce this research which is tackled using a suitable roughness approach according to each di¬mensionality with the purpose of the interaction assessment. A 1D HEC-RAS model, a 2D raster-based diffusion-wave model with a scale-dependent distributed roughness parame-terisation and a 3D finite volume scheme with a porosity algorithm approach to incorporate complex topography have been used. Different topographic sources are assessed using a 1D scheme. LiDAR data are used to isolate the mesh resolution from the topographic content of the DEM effects upon 2D and 3D flow results. A distributed roughness parameterisation, using a roughness height approach dependent upon both mesh resolution and topographic content is developed and evaluated for the 2D scheme. Grain-size data and fractal methods are used for the reconstruction of topography with microscale information, required for some applications but not easily available. Sensitivity of hydraulic parameters to this topographic parameterisation is evaluated in a 3D scheme at different mesh resolu¬tions. Finally, the structural variability of simulated flow is analysed and related to scale interactions. Model simulations demonstrate (i) the importance of the topographic source in a 1D models; (ii) the mesh resolution approach is dominant in 2D and 3D simulations whereas in a 1D model the topographic source and even the roughness parameterisation impacts are more critical; (iii) the increment of the sensitivity to roughness parameterisa-tion in 1D and 2D schemes with detailed topographic sources and finer mesh resolutions; and (iv) the topographic content and microtopography impact throughout the vertical profile of computed 3D velocity in a depth-dependent way, whereas 2D results are not affected by topographic content variations. Finally, the spatial analysis shows that the mesh resolution controls high resolution model scale results, roughness parameterisation control 2D simulation results for a constant mesh resolution; and topographic content and micro-topography variations impacts upon the organisation of flow results depth-dependently in a 3D scheme. Resumen La topografía juega un papel fundamental en la distribución del agua y la energía en los paisajes naturales (Beven and Kirkby 1979; Wood et al. 1997). La simulación hidráulica combinada con métodos de medición del terreno por teledetección constituyen una poderosa herramienta de investigación en la comprensión del comportamiento de los flujos de agua debido a la variabilidad de la superficie sobre la que fluye. La representación e incorporación de la topografía en el esquema hidráulico tiene una importancia crucial en los resultados y determinan el desarrollo de sus aplicaciones al campo medioambiental. Cualquier simulación es una simplificación de un proceso del mundo real, y por tanto el grado de simplificación determinará el significado de los resultados simulados. Este razonamiento es particularmente difícil de trasladar a la simulación hidráulica donde aspectos de la escala tan diferentes como la escala de los procesos de flujo y de representación del contorno son considerados conjuntamente incluso en fases de parametrización (e.g. parametrización de la rugosidad). Por una parte, esto es debido a que las decisiones de escala vienen condicionadas entre ellas (e.g. la dimensionalidad del modelo condiciona la escala de representación del contorno) y por tanto interaccionan en sus resultados estrechamente. Y por otra parte, debido a los altos requerimientos numéricos y computacionales de una representación explícita de alta resolución de los procesos de flujo y discretización de la malla. Además, previo a la modelización hidráulica, la superficie del terreno sobre la que el agua fluye debe ser modelizada y por tanto presenta su propia escala de representación, que a su vez dependerá de la escala de los datos topográficos medidos con que se elabora el modelo. En última instancia, esta topografía es la que determina el comportamiento espacial del flujo. Por tanto, la escala de la topografía en sus fases de medición y modelización (resolución de los datos y representación topográfica) previas a su incorporación en el modelo hidráulico producirá a su vez un impacto que se acumulará al impacto global resultante debido a la escala computacional del modelo hidráulico y su dimensión. La comprensión de las interacciones entre las complejas geometrías del contorno y la estructura del flujo utilizando la modelización hidráulica depende de las escalas consideradas en la simplificación de los procesos hidráulicos y del terreno (dimensión del modelo, tamaño de escala computacional y escala de los datos topográficos). La naturaleza de la aplicación del modelo hidráulico (e.g. habitat físico, análisis de riesgo de inundaciones, transporte de sedimentos) determina en primer lugar la escala del estudio y por tanto el detalle de los procesos a simular en el modelo (i.e. la dimensionalidad) y, en consecuencia, la escala computacional a la que se realizarán los cálculos (i.e. resolución computacional). Esta última a su vez determina, el detalle geográfico con que deberá representarse el contorno acorde con la resolución de la malla computacional. La parametrización persigue incorporar en el modelo hidráulico la cuantificación de los procesos y condiciones físicas del sistema natural y por tanto debe incluir no solo aquellos procesos que tienen lugar a la escala de modelización, sino también aquellos que tienen lugar a un nivel subescalar y que deben ser definidos mediante relaciones de escalado con las variables modeladas explícitamente. Dicha parametrización se implementa en la práctica mediante la provisión de datos al modelo, por tanto la escala de los datos geográficos utilizados para parametrizar el modelo no sólo influirá en los resultados, sino también determinará la importancia del comportamiento subescalar del modelo y el modo en que estos procesos deban ser parametrizados (e.g. la variabilidad natural del terreno dentro de la celda de discretización o el flujo en las direcciones laterales y verticales en un modelo unidimensional). En esta tesis, se han utilizado el modelo unidimensional HEC-RAS, (HEC 1998b), un modelo ráster bidimensional de propagación de onda, (Yu 2005) y un esquema tridimensional de volúmenes finitos con un algoritmo de porosidad para incorporar la topografía, (Lane et al. 2004; Hardy et al. 2005). La geometría del contorno viene definida por la escala de representación topográfica (resolución de malla y contenido topográfico), la cual a su vez depende de la escala de la fuente cartográfica. Todos estos factores de escala interaccionan en la respuesta del modelo hidráulico a la topografía. En los últimos años, métodos como el análisis fractal y las técnicas geoestadísticas utilizadas para representar y analizar elementos geográficos (e.g. en la caracterización de superficies (Herzfeld and Overbeck 1999; Butler et al. 2001)), están promoviendo nuevos enfoques en la cuantificación de los efectos de escala (Lam et al. 2004; Atkinson and Tate 2000; Lam et al. 2006) por medio del análisis de la estructura espacial de la variable (e.g. Bishop et al. 2006; Ju et al. 2005; Myint et al. 2004; Weng 2002; Bian and Xie 2004; Southworth et al. 2006; Pozd-nyakova et al. 2005; Kyriakidis and Goodchild 2006). Estos métodos cuantifican tanto el rango de valores de la variable presentes a diferentes escalas como la homogeneidad o heterogeneidad de la variable espacialmente distribuida (Lam et al. 2004). En esta tesis, estas técnicas se han utilizado para analizar el impacto de la topografía sobre la estructura de los resultados hidráulicos simulados. Los datos de teledetección de alta resolución y técnicas GIS también están siendo utilizados para la mejor compresión de los efectos de escala en modelos medioambientales (Marceau 1999; Skidmore 2002; Goodchild 2003) y se utilizan en esta tesis. Esta tesis como corpus de investigación aborda las interacciones de esas escalas en la modelización hidráulica desde un punto de vista global e interrelacionado. Sin embargo, la estructura y el foco principal de los experimentos están relacionados con las nociones espaciales de la escala de representación en relación con una visión global de las interacciones entre escalas. En teoría, la representación topográfica debe caracterizar la superficie sobre la que corre el agua a una adecuada (conforme a la finalidad y dimensión del modelo) escala de discretización, de modo que refleje los procesos de interés. La parametrización de la rugosidad debe de reflejar los efectos de la variabilidad de la superficie a escalas de más detalle que aquellas representadas explícitamente en la malla topográfica (i.e. escala de discretización). Claramente, ambos conceptos están físicamente relacionados por un

Hydrogeomechanics for rock engineering: coupling subsurface hydrogeomechanical assessement and hydrogeotechnical mapping on fracturated rock masses

The present work aims to achieve and further develop a hydrogeomechanical approach in Caldas da Cavaca hydromineral system rock mass (Aguiar da Beira, NW Portugal), and contribute to a better understanding of the hydrogeological conceptual site model. A collection of several data, namely geology, hydrogeology, rock and soil geotechnics, borehole hydraulics and hydrogeomechanics, was retrieved from three rock slopes (Lagoa, Amores and Cancela). To accomplish a comprehensive analysis and rock engineering conceptualisation of the site, a multi‐technical approach were used, such as, field and laboratory techniques, hydrogeotechnical mapping, hydrogeomechanical zoning and hydrogeomechanical scheme classifications and indexes. In addition, a hydrogeomechanical data analysis and assessment, such as Hydro‐Potential (HP)‐Value technique, JW Joint Water Reduction index, Hydraulic Classification (HC) System were applied on rock slopes. The hydrogeomechanical zone HGMZ 1 of Lagoa slope achieved higher hydraulic conductivities with poorer rock mass quality results, followed by the hydrogeomechanical zone HGMZ 2 of Lagoa slope, with poor to fair rock mass quality and lower hydraulic parameters. In addition, Amores slope had a fair to good rock mass quality and the lowest hydraulic conductivity. The hydrogeomechanical zone HGMZ 3 of Lagoa slope, and the hydrogeomechanical zones HGMZ 1 and HGMZ 2 of Cancela slope had a fair to poor rock mass quality but were completely dry. Geographical Information Systems (GIS) mapping technologies was used in overall hydrogeological and hydrogeomechanical data integration in order to improve the hydrogeological conceptual site model.

Minimization of the experimental workload for the prediction of pollutants propagation in rivers. Mathematical modelling and knowledge re-use

The present thesis in focused on the minimization of experimental efforts for the prediction of pollutant propagation in rivers by mathematical modelling and knowledge re-use. Mathematical modelling is based on the well known advection-dispersion equation, while the knowledge re-use approach employs the methods of case based reasoning, graphical analysis and text mining. The thesis contribution to the pollutant transport research field consists of: (1) analytical and numerical models for pollutant transport prediction; (2) two novel techniques which enable the use of variable parameters along rivers in analytical models; (3) models for the estimation of pollutant transport characteristic parameters (velocity, dispersion coefficient and nutrient transformation rates) as functions of water flow, channel characteristics and/or seasonality; (4) the graphical analysis method to be used for the identification of pollution sources along rivers; (5) a case based reasoning tool for the identification of crucial information related to the pollutant transport modelling; (6) and the application of a software tool for the reuse of information during pollutants transport modelling research. These support tools are applicable in the water quality research field and in practice as well, as they can be involved in multiple activities. The models are capable of predicting pollutant propagation along rivers in case of both ordinary pollution and accidents. They can also be applied for other similar rivers in modelling of pollutant transport in rivers with low availability of experimental data concerning concentration. This is because models for parameter estimation developed in the present thesis enable the calculation of transport characteristic parameters as functions of river hydraulic parameters and/or seasonality. The similarity between rivers is assessed using case based reasoning tools, and additional necessary information can be identified by using the software for the information reuse. Such systems represent support for users and open up possibilities for new modelling methods, monitoring facilities and for better river water quality management tools. They are useful also for the estimation of environmental impact of possible technological changes and can be applied in the pre-design stage or/and in the practical use of processes as well.

Economic optimization method to design telescope irrigation of multiples outlets

In this study is presented an economic optimization method to design telescope irrigation laterals (multidiameter) with regular spaced outlets. The proposed analytical hydraulic solution was validated by means of a pipeline composed of three different diameters. The minimum acquisition cost of the telescope pipeline was determined by an ideal arrangement of lengths and respective diameters for each one of the three segments. The mathematical optimization method based on the Lagrange multipliers provides a strategy for finding the maximum or minimum of a function subject to certain constraints. In this case, the objective function describes the acquisition cost of pipes, and the constraints are determined from hydraulic parameters as length of irrigation laterals and total head loss permitted. The developed analytical solution provides the ideal combination of each pipe segment length and respective diameter, resulting in a decreased of the acquisition cost.

Virtuaalimallin hyödyntäminen harvesteripään tuotekehityksessä

Virtuaalimallinnuksella tarkoitetaan koneen simulointia, jossa huomioidaan koneen mekaniikka, toimilaitteet ja ohjausjärjestelmä. Työn tavoitteena oli luoda virtuaalimalli harvesteripäästä. Kyseinen virtuaalimalli sisälsi harvesteripään tärkeimmät mekaaniset osat, pituusmittalaitteen hydrauliikkapiirin ja tämän ohjauksen. Luodussa virtuaalimallissa huomioitiin myös harvesteripään ja puun väliset kontaktit. Lisäksi työssä tutkittiin mahdollista virtuaalimallinnuksen implementoimista osaksi yrityksen tuotekehitysprosessia. Työssä suoritettiin verifiointimittaukset pituusmittalaitteen hydrauliikkapiirille sekä virtuaalimallin hydrauliikkakomponentit parametrisoitiin. Mittauksista saatuja tuloksia verrattiin virtuaalimallista saatuihin tuloksiin. Työssä esitellään myös ehdotus kuinka virtuaalimallinnusta kannattaisi hyödyntää osana yrityksen tuotekehitysprosessia. Virtuaalimallin eri osa-alueilla saavutetut tulokset osoittavat, että virtuaalimallinuksen hyödyntäminen tuotekehitysprosessin aikana mahdollistaa harvesteripään toimintojen tarkastelun ennen prototyypin rakentamista ja testaamista. Lisäksi hydrauliikkapiirin parametrisoimisella pystytään tutkimaan parametrien vaikutusta kokonaisuuteen.

Response of the benthic macroinvertebrate community to a point source in La Tordera stream (Catalonia, NE Spain)

Vam monitoritzar paràmetres físics i químics, macroinvertebrats bentònics, clorofil·la a, productors primaris i matèria orgànica durant un any (2001-2002) per examinar els efectes d'una font puntual sobre la composició taxonòmica, la estructura de la comunitat, l'organització funcional, la utilització de l'habitat i la estoquiometria al riu la Tordera (Catalunya). Aigües avall de la font puntual, concentració de nutrients, cabal i conductivitat eren majors que al tram d'aigües amunt, mentre que oxigen dissolt era menor. La densitat de macroinvertebrats era més elevada al tram d'aigües avall però la biomassa era similar als dos trams. La riquesa taxonòmica al tram de dalt era un 20% més alt que al tram de baix. Els anàlisis d'ordenació separen clarament els dos trams en el primer eix, mentre que els dos trams presentaven una pauta temporal similar en el segon eix. La similaritat entre els dos trams en composició taxonòmica, densitats i biomasses després de les crescudes d'abril i maig de 2002, indiquen que les pertorbacions del cabal poden actuar com a un mecanisme de reinici de la comunitat bentònica i jugar un paper important per a la restauració d'ecosistemes fluvials. Els dos trams presentaven una biomassa de perifiton, plantes vasculars, CPOM i FPOM similars, mentre que clorofil·la a, algues filamentoses, molses i SPOM eren majors al tram d'aigües avall. La densitat relativa de trituradors era menor sota la font puntual mentre que col·lectors i filtradors van ser afavorits. La biomassa relativa de trituradors també era menor sota la font puntual, però la biomassa de col·lectors i depredadors va augmentar. Les relacions entre densitat de grups tròfics i els seus recursos eren rarament significatives. La relació s'explicava millor amb la biomassa de macroinvertebrats. Els dos trams compartien la mateixa relació per raspadors, col·lectors i filtradors però no per trituradors i depredadors. La densitat i la biomassa de macroinvertebrats es trobaven positivament correlacionades amb la quantitat de recursos tròfics i la complexitat d'habitat, mentre que la riquesa taxonòmica es trobava negativament relacionada amb paràmetres hidràulics. La influència dels substrats inorgànics prenia menor rellevància per a la distribució dels macroinvertebrats. Els anàlisis d'ordenació mostren com les variables del microhabitat de major rellevància eren CPOM, clorofil·la a, algues filamentoses i velocitat. La cobertura de sorra només era significativa per al tram d'aigües amunt i les molses, al d'aigües avall. El número de correlacions significatives entre macroinvertebrats i les variables del microhabitat era més elevat per al tram de dalt que per al de baix, bàsicament per diferències en composició taxonòmica. La biomassa de macroinvertebrats va aportar una informació semblant a la obtinguda per la densitat. Perifiton i molses tenien uns continguts de nutrients similars en els dos trams. Els %C i %N d'algues filamentoses també eren similars en els dos trams però el %P sota la font puntual era el doble que al tram de dalt. Les relacions estoquiomètriques en CPOM, FPOM i SPOM eren considerablement menors sota la font puntual. Els continguts elementals i relacions van ser molt variables entre taxons de macroinvertebrats però no van resultar significativament diferents entre els dos trams. Dípters, tricòpters i efemeròpters presentaven una estoquiometria similar, mentre que el C i el N eren inferiors en moluscs i el P en coleòpters. Els depredadors presentaven un contingut en C i N més elevat que la resta de grups tròfics, mentre que el P era major en els filtradors. Els desequilibris elementals entre consumidors i recursos eren menors en el tram d'aigües avall. A la tardor i l'hivern la major font de nutrients va ser la BOM mentre que a la primavera i a l'estiu va ser el perifiton.

Global scale water stages from SAR imagery (GlosSARi) to support global flood forecasting

Despite the success of studies attempting to integrate remotely sensed data and flood modelling and the need to provide near-real time data routinely on a global scale as well as setting up online data archives, there is to date a lack of spatially and temporally distributed hydraulic parameters to support ongoing efforts in modelling. Therefore, the objective of this project is to provide a global evaluation and benchmark data set of floodplain water stages with uncertainties and assimilation in a large scale flood model using space-borne radar imagery. An algorithm is developed for automated retrieval of water stages with uncertainties from a sequence of radar imagery and data are assimilated in a flood model using the Tewkesbury 2007 flood event as a feasibility study. The retrieval method that we employ is based on possibility theory which is an extension of fuzzy sets and that encompasses probability theory. In our case we first attempt to identify main sources of uncertainty in the retrieval of water stages from radar imagery for which we define physically meaningful ranges of parameter values. Possibilities of values are then computed for each parameter using a triangular ‘membership’ function. This procedure allows the computation of possible values of water stages at maximum flood extents along a river at many different locations. At a later stage in the project these data are then used in assimilation, calibration or validation of a flood model. The application is subsequently extended to a global scale using wide swath radar imagery and a simple global flood forecasting model thereby providing improved river discharge estimates to update the latter.