A novel FPGA-based evolvable hardware system based on multiple processing arrays

In this paper, an architecture based on a scalable and flexible set of Evolvable Processing arrays is presented. FPGA-native Dynamic Partial Reconfiguration (DPR) is used for evolution, which is done intrinsically, letting the system to adapt autonomously to variable run-time conditions, including the presence of transient and permanent faults. The architecture supports different modes of operation, namely: independent, parallel, cascaded or bypass mode. These modes of operation can be used during evolution time or during normal operation. The evolvability of the architecture is combined with fault-tolerance techniques, to enhance the platform with self-healing features, making it suitable for applications which require both high adaptability and reliability. Experimental results show that such a system may benefit from accelerated evolution times, increased performance and improved dependability, mainly by increasing fault tolerance for transient and permanent faults, as well as providing some fault identification possibilities. The evolvable HW array shown is tailored for window-based image processing applications.

Power-Aware Multi-Objective Evolvable Hardware System on an FPGA

Dynamic and Partial Reconfiguration (DPR) allows a system to be able to modify certain parts of itself during run-time. This feature gives rise to the capability of evolution: changing parts of the configuration according to the online evaluation of performance or other parameters. The evolution is achieved through a bio-inspired model in which the features of the system are identified as genes. The objective of the evolution may not be a single one; in this work, power consumption is taken into consideration, together with the quality of filtering, as the measure of performance, of a noisy image. Pareto optimality is applied to the evolutionary process, in order to find a representative set of optimal solutions as for performance and power consumption. The main contributions of this paper are: implementing an evolvable system on a low-power Spartan-6 FPGA included in a Wireless Sensor Network node and, by enabling the availability of a real measure of power consumption at run-time, achieving the capability of multi-objective evolution, that yields different optimal configurations, among which the selected one will depend on the relative “weights” of performance and power consumption.

Vision 2020 - A whole life-cycle information management system for built environments

A whole life-cycle information management vision is proposed, the organizational requirements for the realization of the scenario is investigated. Preliminary interviews with construction professionals are reported. Discontinuities at information transfer throughout life-cycle of built environments are resulting from lack of coordination and multiple data collection/storage practices. A more coherent history of these activities can improve the work practices of various teams by augmenting decision making processes and creating organizational learning opportunities. Therefore, there is a need for unifying these fragmented bits of data to create a meaningful, semantically rich and standardized information repository for built environment. The proposed vision utilizes embedded technologies and distributed building information models. Two diverse construction project types (large one-off design, small repetitive design) are investigated for the applicability of the vision. A functional prototype software/hardware system for demonstrating the practical use of this vision is developed and discussed. Plans for case-studies for validating the proposed model at a large PFI hospital and housing association projects are discussed.

A compact low-cost electronic hardware design for actuating soft robots

A low cost, compact embedded design approach for actuating soft robots is presented. The complete fabrication procedure and mode of operation was demonstrated, and the performance of the complete system was also demonstrated by building a microcontroller based hardware system which was used to actuate a soft robot for bending motion. The actuation system including the electronic circuit board and actuation components was embedded in a 3D-printed casing to ensure a compact approach for actuating soft robots. Results show the viability of the system in actuating and controlling siliconebased soft robots to achieve bending motions. Qualitative measurements of uniaxial tensile test, bending distance and pressure were obtained. This electronic design is easy to reproduce and integrate into any specified soft robotic device requiring pneumatic actuation.

Utilizando programação orientada a aspectos no projeto de sistemas hardware desenvolvidos com SystemC

New programming language paradigms have commonly been tested and eventually incorporated into hardware description languages. Recently, aspect-oriented programming (AOP) has shown successful in improving the modularity of object-oriented and structured languages such Java, C++ and C. Thus, one can expect that, using AOP, one can improve the understanding of the hardware systems under design, as well as make its components more reusable and easier to maintain. We apply AOP in applications developed using the SystemC library. Several examples will be presented illustrating how to combine AOP and SystemC. During the presentation of these examples, the benefits of this new approach will also be discussed

Fault Tolerance Analysis and Self-Healing Strategy of Autonomous, Evolvable Hardware Systems

This paper presents an analysis of the fault tolerance achieved by an autonomous, fully embedded evolvable hardware system, which uses a combination of partial dynamic reconfiguration and an evolutionary algorithm (EA). It demonstrates that the system may self-recover from both transient and cumulative permanent faults. This self-adaptive system, based on a 2D array of 16 (4×4) Processing Elements (PEs), is tested with an image filtering application. Results show that it may properly recover from faults in up to 3 PEs, that is, more than 18% cumulative permanent faults. Two fault models are used for testing purposes, at PE and CLB levels. Two self-healing strategies are also introduced, depending on whether fault diagnosis is available or not. They are based on scrubbing, fitness evaluation, dynamic partial reconfiguration and in-system evolutionary adaptation. Since most of these adaptability features are already available on the system for its normal operation, resource cost for self-healing is very low (only some code additions in the internal microprocessor core)

Desarrollo de aplicaciones basadas en Linux Embedded en una arquitectura basada en Cyclone V SoC (System on Chip) de Altera

We attempt to integrate and start up the set of necessary tools to deploy the design cycle of embedded systems based on Embedded Linux on a "Cyclone V SoC" made by Altera. First, we will analyze the available tools for designing the hardware system of the SoCkit development kit, made by Arrow, which has a "Cyclone V SoC" system (based on a "ARM Cortex-A9 MP Core" architecture). When designing the SoCkit board hardware, we will create a new peripheral to integrate it into the hardware system, so it can be used as any other existent resource of the SoCkit board previously configured. Next, we will analyze the tools to generate an Embedded Linux distribution adapted to the SoCkit board. In order to generate the Linux distribution we will use, on the one hand, a software package from Yocto recommended by Altera; on the other hand, the programs and tools of Altera, Embedded Development Suite. We will integrate all the components needed to build the Embedded Linux distribution, creating a complete and functional system which can be used for developing software applications. Finally, we will study the programs for developing and debugging applications in C or C++ language that will be executed in this hardware platform, then we will program a Linux application as an example to illustrate the use of SoCkit board resources. RESUMEN Se pretende integrar y poner en funcionamiento el conjunto de herramientas necesarias para desplegar el ciclo de diseño de sistemas embebidos basados en "Embedded Linux" sobre una "Cyclone V SoC" de Altera. En primer lugar, se analizarán las diversas herramientas disponibles para diseñar el sistema hardware de la tarjeta de desarrollo SoCkit, fabricada por Arrow, que dispone de un sistema "Cyclone V SoC" (basado en una arquitectura "ARM Cortex A9 MP Core"). En el diseño hardware de la SoCkit se creará un periférico propio y se integrará en el sistema, pudiendo ser utilizado como cualquier otro recurso de la tarjeta ya existente y configurado. A continuación, también se analizarán las herramientas para generar una distribución de "Embedded Linux" adaptado a la placa SoCkit. Para generar la distribución de Linux se utilizará, por una parte, un paquete software de Yocto recomendado por Altera y, por otra parte, las propias herramientas y programas de Altera. Se integrarán todos los componentes necesarios para construir la distribución Linux, creando un sistema completo y funcional que se pueda utilizar para el desarrollo de aplicaciones software. Por último, se estudiarán las herramientas para el diseño y depuración de aplicaciones en lenguaje C ó C++ que se ejecutarán en esta plataforma hardware. Se pretende desarrollar una aplicación de ejemplo para ilustrar el uso de los recursos más utilizados de la SoCkit.

Desarrollo de un sistema hardware modular que implemente los instrumentos de un laboratorio de electrónica

El poder disponer de la instrumentación y los equipos electrónicos resulta vital en el diseño de circuitos analógicos. Permiten realizar las pruebas necesarias y el estudio para el buen funcionamiento de estos circuitos. Los equipos se pueden diferenciar en instrumentos de excitación, los que proporcionan las señales al circuito, y en instrumentos de medida, los que miden las señales generadas por el circuito. Estos equipos sirven de gran ayuda pero a su vez tienen un precio elevado lo que impide en muchos casos disponer de ellos. Por esta principal desventaja, se hace necesario conseguir un dispositivo de bajo coste que sustituya de alguna manera a los equipos reales. Si el instrumento es de medida, este sistema de bajo coste puede ser implementado mediante un equipo hardware encargado de adquirir los datos y una aplicación ejecutándose en un ordenador donde analizarlos y presentarlos en la pantalla. En el caso de que el instrumento sea de excitación, el único cometido del sistema hardware es el de proporcionar las señales cuya configuración ha enviado el ordenador. En un equipo real, es el propio equipo el que debe realizar todas esas acciones: adquisición, procesamiento y presentación de los datos. Además, la dificultad de realizar modificaciones o ampliaciones de las funcionalidades en un instrumento tradicional con respecto a una aplicación de queda patente. Debido a que un instrumento tradicional es un sistema cerrado y uno cuya configuración o procesamiento de datos es hecho por una aplicación, algunas de las modificaciones serían realizables modificando simplemente el software del programa de control, por lo que el coste de las modificaciones sería menor. En este proyecto se pretende implementar un sistema hardware que tenga las características y realice las funciones del equipamiento real que se pueda encontrar en un laboratorio de electrónica. También el desarrollo de una aplicación encargada del control y el análisis de las señales adquiridas, cuya interfaz gráfica se asemeje a la de los equipos reales para facilitar su uso. ABSTRACT. The instrumentation and electronic equipment are vital for the design of analogue circuits. They enable to perform the necessary testing and study for the proper functioning of these circuits. The devices can be classified into the following categories: excitation instruments, which transmit the signals to the circuit, and measuring instruments, those in charge of measuring the signals produced by the circuit. This equipment is considerably helpful, however, its high price often makes it hardly accessible. For this reason, low price equipment is needed in order to replace real devices. If the instrument is measuring, this low cost system can be implemented by hardware equipment to acquire the data and running on a computer where analyzing and present on the screen application. In case of an excitation the instrument, the only task of the hardware system is to provide signals which sent the computer configuration. In a real instrument, is the instrument itself that must perform all these actions: acquisition, processing and presentation of data. Moreover, the difficulty of making changes or additions to the features in traditional devices with respect to an application running on a computer is evident. This is due to the fact that a traditional instrument is a closed system and its configuration or data processing is made by an application. Therefore, certain changes can be made just by modifying the control program software. Consequently, the cost of these modifications is lower. This project aims to implement a hardware system with the same features and functions of any real device, available in an electronics laboratory. Besides, it aims to develop an application for the monitoring and analysis of acquired signals. This application is provided with a graphic interface resembling those of real devices in order to facilitate its use.

Minimalist Hardware Architectures for Agent Tracking and Guidance

The philosophy of minimalism in robotics promotes gaining an understanding of sensing and computational requirements for solving a task. This minimalist approach lies in contrast to the common practice of first taking an existing sensory motor system, and only afterwards determining how to apply the robotic system to the task. While it may seem convenient to simply apply existing hardware systems to the task at hand, this design philosophy often proves to be wasteful in terms of energy consumption and cost, along with unnecessary complexity and decreased reliability. While impressive in terms of their versatility, complex robots such as the PR2 (which cost hundreds of thousands of dollars) are impractical for many common applications. Instead, if a specific task is required, sensing and computational requirements can be determined specific to that task, and a clever hardware implementation can be built to accomplish the task. Since this minimalist hardware would be designed around accomplishing the specified task, significant reductions in hardware complexity can be obtained. This can lead to huge advantages in battery life, cost, and reliability. Even if cost is of no concern, battery life is often a limiting factor in many applications. Thus, a minimalist hardware system is critical in achieving the system requirements. In this thesis, we will discuss an implementation of a counting, tracking, and actuation system as it relates to ergodic bodies to illustrate a minimalist design methodology.

Evaluating shock absorption behavior of small-sized systems under programmable electric field

A simple ball-drop impact tester is developed for studying the dynamic response of hierarchical, complex, small-sized systems and materials. The developed algorithm and set-up have provisions for applying programmable potential difference along the height of a test specimen during an impact loading; this enables us to conduct experiments on various materials and smart structures whose mechanical behavior is sensitive to electric field. The software-hardware system allows not only acquisition of dynamic force-time data at very fast sampling rate (up to 2 x 10(6) samples/s), but also application of a pre-set potential difference (up to +/- 10 V) across a test specimen for a duration determined by feedback from the force-time data. We illustrate the functioning of the set-up by studying the effect of electric field on the energy absorption capability of carbon nanotube foams of 5 x 5 x 1.2 mm(3) size under impact conditions. (C) 2014 AIP Publishing LLC.

FPGA-based object detection using classification circuits

Dans l'apprentissage machine, la classification est le processus d’assigner une nouvelle observation à une certaine catégorie. Les classifieurs qui mettent en œuvre des algorithmes de classification ont été largement étudié au cours des dernières décennies. Les classifieurs traditionnels sont basés sur des algorithmes tels que le SVM et les réseaux de neurones, et sont généralement exécutés par des logiciels sur CPUs qui fait que le système souffre d’un manque de performance et d’une forte consommation d'énergie. Bien que les GPUs puissent être utilisés pour accélérer le calcul de certains classifieurs, leur grande consommation de puissance empêche la technologie d'être mise en œuvre sur des appareils portables tels que les systèmes embarqués. Pour rendre le système de classification plus léger, les classifieurs devraient être capable de fonctionner sur un système matériel plus compact au lieu d'un groupe de CPUs ou GPUs, et les classifieurs eux-mêmes devraient être optimisés pour ce matériel. Dans ce mémoire, nous explorons la mise en œuvre d'un classifieur novateur sur une plate-forme matérielle à base de FPGA. Le classifieur, conçu par Alain Tapp (Université de Montréal), est basé sur une grande quantité de tables de recherche qui forment des circuits arborescents qui effectuent les tâches de classification. Le FPGA semble être un élément fait sur mesure pour mettre en œuvre ce classifieur avec ses riches ressources de tables de recherche et l'architecture à parallélisme élevé. Notre travail montre que les FPGAs peuvent implémenter plusieurs classifieurs et faire les classification sur des images haute définition à une vitesse très élevée.

Implementação em FPGA de um sistema para processamento de imagens digitais para aplicações diversificadas

Pós-graduação em Ciência da Computação - IBILCE

Estabilizador de sistemas de potência digital aplicado a uma unidade geradora da UHE de Tucuruí

Este trabalho apresenta o desenvolvimento e resultados de testes de campo de um estabilizador de sistemas de potência (ESP) digital, destinado ao amortecimento de oscilações eletromecânicas em sistemas interligados. Os testes experimentais foram efetuados em uma das unidades hidrogeradoras, de 350 MVA, da UHE de Tucuruí. A lei de controle amortecedor do ESP digital foi embarcada em um sistema de hardware baseado em um controlador digital de sinais (DSPIC 30f5011). A estrutura da lei de controle é na forma canónica RST, de tempo discreto, sendo os parâmetros do controlador calculados através da técnica de deslocamento radial de pólos. Para fins de projeto, a dinâmica da planta, no ponto de operação considerado, foi representada por um modelo paramétrico, o qual foi estimado a partir de dados medidos em campo. Os resultados experimentais mostraram um excelente desempenho do ESP digital no amortecimento de um dos modos eletromecânicos observável na UHE de Tucuruí.

Projeto e desenvolvimento de robô cartesiano de baixo custo para manipulação de produtos em linhas de média cadência

Pós-graduação em Engenharia Elétrica - FEB