An optimal transform Architecture for H.264/AVC

This paper presents the design of the area optimized integer two dimensional discrete cosine transform (2-D DCT) used in H.264/AVC codecs. The 2-D DCT calculation is performed by utilizing the separability property, in such a way that 2-D DCT is divided into two 1-D DCT calculation that are joined through a common memory. Due to its area optimized approach, the design will find application in mobile devices. Verilog hardware description language (HDL) in cadence environment has been used for design, compilation, simulation and synthesis of transform block in 0.18 mu TSMC technology.

Reconfigurable IEEE1451-FPGA based weblab infrastructure

Weblabs are spreading their influence in Science and Engineering (S&E) courses providing a way to remotely conduct real experiments. Typically, they are implemented by different architectures and infrastructures supported by Instruments and Modules (I&Ms) able to be remotely controlled and observed. Besides the inexistence of a standard solution for implementing weblabs, their reconfiguration is limited to a setup procedure that enables interconnecting a set of preselected I&Ms into an Experiment Under Test (EUT). Moreover, those I&Ms are not able to be replicated or shared by different weblab infrastructures, since they are usually based on hardware platforms. Thus, to overcome these limitations, this paper proposes a standard solution that uses I&Ms embedded into Field-Programmable Gate Array (FPGAs) devices. It is presented an architecture based on the IEEE1451.0 Std. supported by a FPGA-based weblab infrastructure able to be remotely reconfigured with I&Ms, described through standard Hardware Description Language (HDL) files, using a Reconfiguration Tool (RecTool).

A New Approach for Real Time Fault Diagnosis in Induction Motors Based on Vibration Measurement

Condition monitoring is used to increase machinery availability and machinery performance, reducing consequential damage, increasing machine life, reducing spare parts inventories, and reducing breakdown maintenance. An efficient real time vibration measurement and analysis instruments is capable of providing warning and predicting faults at early stages. In this paper, a new methodology for the implementation of vibration measurement and analysis instruments in real time based on circuit architecture mapped from a MATLAB/Simulink model is presented. In this study, signal processing applications such as FIR filters and fast Fourier transform are treated as systems, which are implemented in hardware using a system generator toolbox, which translates a Simulink model in a hardware description language - HDL for FPGA implementations.

Modelagem IEEE 1815 DNP3 em VHDL e análise de comunicação SG via IEEE 802.15.4 e IEEE 802.11

Pós-graduação em Engenharia Elétrica - FEIS

Improving the freshman electrical and computer engineering lab

This thesis covers the challenges of creating and maintaining an introductory engineering laboratory. The history of the University of Illinois Electrical and Computer Engineering department’s introductory course, ECE 110, is recounted. The current state of the course, as of Fall 2008, is discussed along with current challenges arising from the use of a hand-wired prototyping board with logic gates. A plan for overcoming these issues using a new microcontroller-based board with a pseudo hardware description language is discussed. The new microcontroller based system implementation is extensively detailed along with its new accompanying description language. This new system was tried in several sections of the Fall 2008 semester alongside the old system; the students’ final performances with the two different approaches are compared in terms of design, performance, complexity, and enjoyment. The system in its first run shows great promise, increasing the students’ enjoyment, and improving the performance of their designs.

Arquitetura multiprocessada e reconfigurável para a síntese de redes de Petri em hardware

Uma arquitetura reconfigurável e multiprocessada para a implementação física de Redes de Petri foi desenvolvida em VHDL e mapeada sobre um FPGA. Convencionalmente, as Redes de Petri são transformadas em uma linguagem de descrição de hardware no nível de transferências entre registradores e um processo de síntese de alto nível é utilizado para gerar as funções booleanas e tabelas de transição de estado para que se possa, finalmente, mapeá-las num FPGA (Morris et al., 2000) (Soto and Pereira, 2001). A arquitetura proposta possui blocos lógicos reconfiguráveis desenvolvidos exclusivamente para a implementação dos lugares e das transições da rede, não sendo necessária a descrição da rede em níveis de abstração intermediários e nem a utilização de um processo de síntese para realizar o mapeamento da rede na arquitetura. A arquitetura permite o mapeamento de modelos de Redes de Petri com diferenciação entre as marcas e associação de tempo no disparo das transições, sendo composta por um arranjo de processadores reconfiguráveis, cada um dos quais representando o comportamento de uma transição da Rede de Petri a ser mapeada e por um sistema de comunicação, implementado por um conjunto de roteadores que são capazes de enviar pacotes de dados de um processador reconfigurável a outro. A arquitetura proposta foi validada num FPGA de 10.570 elementos lógicos com uma topologia que permitiu a implementação de Redes de Petri de até 9 transições e 36 lugares, atingindo uma latência de 15,4ns e uma vazão de até 17,12GB/s com uma freqüência de operação de 64,58MHz.

Hybrid three-phase HPF rectifier with programmable input current THD, using FPGA device and VHDL language

In this paper is proposed and analyzed a digital hysteresis modulation using a FPGA (Field Programmable Gate Array) device and VHDL (Hardware Description Language), applied at a hybrid three-phase rectifier with almost unitary input power factor, composed by parallel SEPIC controlled single-phase rectifiers connected to each leg of a standard 6-pulses uncontrolled diode rectifier. The digital control allows a programmable THD (Total Harmonic Distortion) at the input currents, and it makes possible that the power rating of the switching-mode converters, connected in parallel, can be a small fraction of the total average output power, in order to obtain a compact converter, reduced input current THD and almost unitary input power factor. Finally, the proposed digital control, using a FPGA device and VHDL, offers an important flexibility for the associated control technique, in order to obtain a programmable PFC (Power Factor Correction) hybrid three-phase rectifier, in agreement with the international standards (IEC, and IEEE), which impose limits for the THD of the AC (Alternate Current) line input currents. The proposed strategy is verified by experiments. © 2008 IEEE.

A synthesizable hardware evolutionary algorithm design for unmanned aerial system real-time path planning

The main objective of this paper is to detail the development of a feasible hardware design based on Evolutionary Algorithms (EAs) to determine flight path planning for Unmanned Aerial Vehicles (UAVs) navigating terrain with obstacle boundaries. The design architecture includes the hardware implementation of Light Detection And Ranging (LiDAR) terrain and EA population memories within the hardware, as well as the EA search and evaluation algorithms used in the optimizing stage of path planning. A synthesisable Very-high-speed integrated circuit Hardware Description Language (VHDL) implementation of the design was developed, for realisation on a Field Programmable Gate Array (FPGA) platform. Simulation results show significant speedup compared with an equivalent software implementation written in C++, suggesting that the present approach is well suited for UAV real-time path planning applications.

Towards a unified service description language for the internet of services : requirements and first developments

Service-oriented Architectures (SOA) and Web services leverage the technical value of solutions in the areas of distributed systems and cross-enterprise integration. The emergence of Internet marketplaces for business services is driving the need to describe services, not only from a technical level, but also from a business and operational perspective. While, SOA and Web services reside in an IT layer, organizations owing Internet marketplaces are requiring advertising and trading business services which reside in a business layer. As a result, the gap between business and IT needs to be closed. This paper presents USDL (Unified Service Description Language), a specification language to describe services from a business, operational and technical perspective. USDL plays a major role in the Internet of Services to describe tradable services which are advertised in electronic marketplaces. The language has been tested using two service marketplaces as use cases.

A unified description language for human to automated services

Through the rise of cloud computing, on-demand applications, and business networks, services are increasingly being exposed and delivered on the Internet and through mobile communications. So far, services have mainly been described through technical interface descriptions. The description of business details, such as pricing, service-level, or licensing, has been neglected and is therefore hard to automatically process by service consumers. Also, third-party intermediaries, such as brokers, cloud providers, or channel partners, are interested in the business details in order to extend services and their delivery and, thus, further monetize services. In this paper, the constructivist design of the UnifiedServiceDescriptionLanguage (USDL), aimed at describing services across the human-to-automation continuum, is presented. The proposal of USDL follows well-defined requirements which are expressed against a common service discourse and synthesized from currently available servicedescription efforts. USDL's concepts and modules are evaluated for their support of the different requirements and use cases.

Aprendizaje basado en proyectos en Diseño y Construcción de Sistemas Digitales

Duración (en horas): Más de 50 horas. Destinatario: Estudiante y Docente