Distribution of carbon nanotubes in fresh ordinary Portland cement pastes: understanding from a two-phase perspective

Significant research advances have been made in the field of carbon nanotube (CNT) reinforced ordinary Portland cement (OPC) paste composites in recent years. However, the distribution of CNTs in fresh OPC paste is yet to be fully researched and quantified, thereby creating a technical barrier to CNT utilization in concrete construction. In this study, fresh OPC paste was treated as a two-phase material containing solid particles (cement grains) and liquid solutions (pore solutions). A centrifugation-based technique was proposed to separate these two phases and the presence of CNTs in each phase was quantified. UV-Vis spectrometry showed that the degree of dispersion can achieve above 90 wt% using polycarboxylate superplasticizer. The results suggested an upper limit of 0.26 wt% for CNT addition into water before mixing with OPC, and the dispersion was found to be stable for at least 4 hours. Based on scanning electron imaging, the adsorption phenomenon of CNTs on OPC grains with size less than 4 μm was discovered. Energy-dispersive X-ray spectroscopy indicated these adsorptive particles have lower Ca to Si ratio. It was observed that about 0.5 mg of CNTs per gram of OPC grains was adsorbed in solid OPC grains in typical fresh OPC pastes. On the basis of these results, a conceptual model was proposed for the distribution of CNTs in fresh OPC paste where about 33 wt% of the CNTs stay in pore solution and 65 wt% of CNTs are adsorbed on OPC grains.

Hydration and anomalous solubility of the Bell-Lavis model as solvent

We address the investigation of the solvation properties of the minimal orientational model for water originally proposed by [Bell and Lavis, J. Phys. A 3, 568 (1970)]. The model presents two liquid phases separated by a critical line. The difference between the two phases is the presence of structure in the liquid of lower density, described through the orientational order of particles. We have considered the effect of a small concentration of inert solute on the solvent thermodynamic phases. Solute stabilizes the structure of solvent by the organization of solvent particles around solute particles at low temperatures. Thus, even at very high densities, the solution presents clusters of structured water particles surrounding solute inert particles, in a region in which pure solvent would be free of structure. Solute intercalates with solvent, a feature which has been suggested by experimental and atomistic simulation data. Examination of solute solubility has yielded a minimum in that property, which may be associated with the minimum found for noble gases. We have obtained a line of minimum solubility (TmS) across the phase diagram, accompanying the line of maximum density. This coincidence is easily explained for noninteracting solute and it is in agreement with earlier results in the literature. We give a simple argument which suggests that interacting solute would dislocate TmS to higher temperatures.

Agent-based model for the effect of curing temperature on cement hydration

The agent-based model presented here, comprises an algorithm that computes the degree of hydration, the water consumption and the layer thickness of C-S-H gel as functions of time for different temperatures and different w/c ratios. The results are in agreement with reported experimental studies, demonstrating the applicability of the model. As the available experimental results regarding elevated curing temperature are scarce, the model could be recalibrated in the future. Combining the agent-based computational model with TGA analysis, a semiempirical method is achieved to be used for better understanding the microstructure development in ordinary cement pastes and to predict the influence of temperature on the hydration process.

Hypothetical model of hydrophilic lubrication in synovial joints

This paper presents a new insight into the mechanism of biolubrication of articulating mammalian joints that includes the function of surface-active phospholipids (SAPLs). SAPLs can be adsorbed on surface of cartilage membranes as a hydrophobic monolayer (H-phobic-M Madel or Hills' Model) or as a newly proposed hydrophilic bilayer (H-philic-B Model). With respect to the synovial joint's frictionless work, three processes are identified namely: monolayer/bilayer phospholipids binding to cartilage with lubricin interaction; influence of induced-pressure on interaction of hyaluronan with phospholipids; and biolubrication arising from two gliding articular hydrophilic surfaces acting as reverse micelle. Lubricin is considered to play critical role as a supplier of phospholipids, which overlay the articular surface of articular cartilage. Hyaluronic acid is considered to play a critical mediating role in the interaction between the hydrophilic part of phospholipids, the articular surface and water (hydration) in facilitating the lubrication process. Tivo models of frictionless lubrication processes, namely hydrophobic (H-phobic-M Model) and our conceptual hydrophilic (H-philic-B Model), are compared. © Institution of Engineers Australia, 2008.

A model for the interaction of trifluoroethanol with peptides and proteins

The structural stabilizing property of 2,2,2-trifluoroethanol (TFE) in peptides has been widely demonstrated, More recently, TFE has been shown to enhance secondary structure content in globular proteins, and to influence quaternary interactions in protein multimers. The molecular mechanisms by which TFE exerts its Influence on peptide and protein structures remain poorly understood. The present analysis integrates the known physical properties of TFE with a variety of experimental observations on the interaction of TFE with peptides and proteins and on the properties of fluorocarbons. Two features of TFE, namely the hydrophobicity of the trifluoromethyl group and the hydrogen bonding character (strong donor and poor acceptor), emerge as the most important factors for rationalising the observed effects of TFE. A model is proposed for TFE interaction with peptides which involves an initial replacement of the hydration shell by fluoroalcohol molecules, a process driven by apolar interactions and favourable entropy of dehydration. Subsequent bifurcated hydrogen-bond formation with peptide carbonyl groups, which leave intramolecular interactions unaffected, promotes secondary structure formation.

Entropy and dynamics of water in hydration layers of a bilayer

We compute the entropy and transport properties of water in the hydration layer of dipalmitoylphosphatidylcholine bilayer by using a recently developed theoretical scheme two-phase thermodynamic model, termed as 2PT method; S.-T. Lin et al., J. Chem. Phys. 119, 11792 (2003)] based on the translational and rotational velocity autocorrelation functions and their power spectra. The weights of translational and rotational power spectra shift from higher to lower frequency as one goes from the bilayer interface to the bulk. Water molecules near the bilayer head groups have substantially lower entropy (48.36 J/mol/K) than water molecules in the intermediate region (51.36 J/mol/K), which have again lower entropy than the molecules (60.52 J/mol/K) in bulk. Thus, the entropic contribution to the free energy change (T Delta S) of transferring an interface water molecule to the bulk is 3.65 kJ/mol and of transferring intermediate water to the bulk is 2.75 kJ/mol at 300 K, which is to be compared with 6.03 kJ/mol for melting of ice at 273 K. The translational diffusion of water in the vicinity of the head groups is found to be in a subdiffusive regime and the rotational diffusion constant increases going away from the interface. This behavior is supported by the slower reorientational relaxation of the dipole vector and OH bond vector of interfacial water. The ratio of reorientational relaxation time for Legendre polynomials of order 1 and 2 is approximately 2 for interface, intermediate, and bulk water, indicating the presence of jump dynamics in these water molecules. (C) 2010 American Institute of Physics. doi:10.1063/1.3494115]

Properties of two model soils stabilized with different blends and contents of GGBS, MgO, lime, and PC

This paper addresses the use of ground granulated blast furnace slag (GGBS) and reactive magnesia (MgO) blends for soil stabilization, comparing them with GGBS-lime blends and Portland cement (PC) for enhanced technical performance. A range of tests were conducted to investigate the properties of stabilized soils, including unconfined compressive strength (UCS), permeability, and microstructural analyses by using X-ray diffraction (XRD) and scanning electron microscopy (SEM). The influence of GGBS:MgO ratio, binder content, soil type, and curing period were addressed. The UCS results revealed that GGBS-MgO was more efficient than GGBS-lime as a binder for soil stabilization, with an optimum MgO content in the range of 5-20% of the blends content, varying with binder content and curing age. The 28-day UCS values of the optimum GGBS-MgO mixes were up to almost four times higher than that of corresponding PC mixes. The microstructural analyses showed the hydrotalcite was produced during the GGBS hydration activated by MgO, although the main hydration products of the GGBS-MgO stabilized soils were similar to those of PC. © 2014 American Society of Civil Engineers.

In vitro drug release studies of polymeric freeze-dried wafers and solvent-cast films using paracetamol as a model soluble drug

Drug dissolution and release characteristics from freeze-dried wafers and solvent-cast films prepared from sodium carboxymethylcellulose (CMC) have been investigated to determine the mechanisms of drug release from the two systems. The formulations were prepared by freeze-drying (wafers) or drying in air (films), the hydrated gel of the polymer containing paracetamol as a model soluble drug. Scanning electron microscopy (SEM) was used to examine differences between the physical structure of the wafers and films. Dissolution studies were performed using an exchange cell and drug release was measured by UV spectroscopy at 242 nm. The effects of drug loading, polymer content and amount of glycerol (films) on the release characteristics of paracetamol were investigated. The release profiles of paracetamol from the wafers and films were also compared. A digital camera was used to observe the times to complete hydration and dissolution of the wafers containing different amounts of CMC and how that impacts on drug release rates. Both formulations showed sustained type drug release that was modelled by the Korsmeyer–Peppas equation. Changes in the concentration of drug and glycerol (films) did not significantly alter the rate of drug release while increasing polymer content significantly decreased the rate of drug release from both formulations. The results show that the rate of paracetamol release was faster from the wafers than the corresponding films due to differences in their physical structures. The wafers which formed a porous network, hydrated faster than the more dense and continuous, (non-porous) sheet-like structure of the films.

Effect of solvent hydration and temperature in the deacidification process of sunflower oil using ethanol

This work presents liquid-liquid experimental data for systems composed of sunflower seed oil, ethanol and water from 10 to 60 degrees C. The influence of process variables (temperature (T) and water concentration in the solvent (W)) on both the solvent content present in the raffinate (S(RP)) and extract (S(EP)) phases and the partition of free fatty acids (k(2)) was evaluated using the response surface methodology, where flash calculations were performed for each trial using the UNIQUAC equation. Water content in the solvent was the most important factor on the responses of S(EP) and k(2). Additionally, statistical analysis showed that the S(RP) was predominantly affected by temperature factor for low water content in the solvent. (c) 2009 Elsevier Ltd. All rights reserved.

The reactivity of bis(para-methoxyphenyl)telluroxide towards triflic acid and diphenylphosphinic acid. Theoretical considerations of the protonation and hydration process of diorganotelluroxanes

The reaction of (p-MeOC₆H₄)₂TeO with two equivalents of HO₃SCF₃ and HO₂PPh₂ provided the tetraorganoditelluroxanes (F₃CSO₃)(p-MeOC₆H₄)₂TeOTe(p-MeOC₆H₄)₂(O₃SCF₃) (1) and (Ph₂PO₂)(p-MeOC₆H₄)₂TeOTe(p-MeOC₆H₄)₂(O₂PPh₂)·2 Ph₂PO₂H (2) in good yields. Compounds 1 and 2 were characterized by solution and solid-state ³¹P and ¹²⁵Te NMR spectroscopy, IR spectroscopy, electrospray mass spectrometry, conductivity measurements and single crystal X-ray diffraction. In solution, compound 1 undergoes an electrolytic dissociation and reversibly reacts with traces of water to give the mononuclear cation [(p-MeOC₆H₄)₂TeOH]⁺ and triflate anions. Theoretical aspects of the protonation and hydration of model telluroxanes R₂TeO (R = H, Me, Ph) were investigated by preliminary DFT calculations and compared to the corresponding selenoxanes R₂SeO. The tellurium dihydroxides R₂Te(OH)₂ seem to be more stable than the hydrogen-bonded complexes R₂TeO·H₂O.

Water regulation of actinomycin-D binding to DNA: the interplay among drug affinity, DNA long-range conformation, and hydration

Actiaomycin-D (actD) binds to natural DNA at two different classes of binding sites, weak and strong. The affinity for these sites is highly dependent on DNA se(sequence and solution conditions, and the interaction appears to be purely entropic driven Although the entropic character of this reaction has been attributed to the release of water molecules upon drug to DNA complex formation, the mechanism by which hydration regulates actD binding and discrimination between different classes of binding sites on natural DNA is still unknown. In this work, we investigate the role of hydration on this reaction using the osmotic stress method. We skew that the decrease of solution water activity, due to the addition of sucrose, glycerol ethylene glycol, and betaine, favors drug binding to the strong binding sites on DNA by increasing both the apparent binding affinity Delta G, and the number of DNA base pairs apparently occupied by the bound drug n(bp/actD). These binding parameters vary linearly with the logarithm of the molar fraction of water in solution log(X-w), which indicates the contribution of water binding to the energetic of the reaction. It is demonstrated that the hydration change measured upon binding increases proportionally to the apparent size of the binding site n(bp/uctD). This indicates that n(bp/actD) measured from the Scatchard plod is a measure of the size of the DNA molecule changing conformation due to ligand binding. We also find that the contribution of DNA deformation, gauged by n(bp/act) to the total free energy of binding Delta G, is given by Delta G = Delta G(local) + n(bp/actD) x delta G(DNA), where Delta G(local), = -8020 +/- 51 cal/mol of actD bound and delta G(DNa) = -24.1 +/- 1.7cal/mol of base pair at 25 degrees C. We interpret Delta G(local), as the energetic contribution due to the direct interactions of actD with the actual tetranucleotide binding site, and it n(bp/actB) X delta G(DNA) as that due to change inconformation, induced by binding, of it n(bp/actD) DNA base pairs flanking the local site. This interpretation is supported by the agreement found between the value of delta G(DNA) and the torsional free energy change measured independently. We conclude suggesting an allosteric model for ligand binding to DNA, such that the increase in binding affinity is achieved by increasing the relaxation of the unfavorable free energy of binding storage at the local site through a larger number of DNA base pairs. The new aspect on this model is that the size of the complex is not fixed but determined by solutions conditions, such as water activity, which modulate the energetic barrier to change helix conformation. These results may suggest that long-range allosteric transitions of duplex DNA are involved in the inhibition of RNA synthesis by actD, and more generally, in the regulation of transcription. (C) 2000 John Wiley & Sons, Inc.

Structure and anomalous solubility for hard spheres in an associating lattice gas model

In this paper we investigate the solubility of a hard-sphere gas in a solvent modeled as an associating lattice gas. The solution phase diagram for solute at 5% is compared with the phase diagram of the original solute free model. Model properties are investigated both through Monte Carlo simulations and a cluster approximation. The model solubility is computed via simulations and is shown to exhibit a minimum as a function of temperature. The line of minimum solubility (TmS) coincides with the line of maximum density (TMD) for different solvent chemical potentials, in accordance with the literature on continuous realistic models and on the "cavity" picture. (C) 2012 American Institute of Physics. [http://dx.doi.org/10.1063/1.4743635]

Use of the Supermolecule Approach To Model the Syn and Anti Conformations of Solvated Cyclic 3‘,5‘-Adenosine Monophosphate

The supermolecule approach has been used to model the hydration of cyclic 3‘,5‘-adenosine monophosphate, cAMP. Model building combined with PM3 optimizations predict that the anti conformer of cAMP is capable of hydrogen bonding to an additional solvent water molecule compared to the syn conformer. The addition of one water to the syn superstructure with concurrent rotation of the base about the glycosyl bond to form the anti superstructure leads to an additional enthalpy of stabilization of approximately −6 kcal/mol at the PM3 level. This specific solute−solvent interaction is an example of a large solvent effect, as the method predicts that cAMP has a conformational preference for the anti isomer in solution. This conformational preference results from a change in the number of specific solute−solvent interactions in this system. This prediction could be tested by NMR techniques. The number of waters predicted to be in the first hydration sphere around cAMP is in agreement with the results of hydration studies of nucleotides in DNA. In addition, the detailed picture of solvation about this cyclic nucleotide is in agreement with infrared experimental results.