Effect of Heat Pipe Figure of Merit on an Evaporating Thin Film

The performance of a two-phase heat transport device such as the loop heat pipe is influenced by the evaporative heat transfer coefficient in the evaporator. From previous experiments with loop heat pipes, it has been observed that fluids with a high heat pipe figure of merit have a high heat transfer coefficient. Considering an evaporating extended thin film, this paper theoretically corroborates this experimental observation by deriving a direct link between the evaporative heat flux at the interface and the fluid figures of merit (namely interline heat flow parameter and heat pipe figure of merit) in the thin film. Numerical experiments with different working fluids clearly show that a fluid with high figure of merit also has a high cumulative heat transfer in the microregion encompassing the evaporating thin film. Thus, a loop heat pipe or heat pipe that uses a working fluid with a high interline heat flow parameter and heat pipe figure of merit will lead to a high evaporative heat transfer coefficient.

Planar silver nanowire, carbon nanotube and PEDOT:PSS nanocomposite transparent electrodes

Highly conductive, transparent and flexible planar electrodes were fabricated using interwoven silver nanowires and single-walled carbon nanotubes (AgNW:SWCNT) in a PEDOT:PSS matrix via an epoxy transfer method from a silicon template. The planar electrodes achieved a sheet resistance of 6.6 ± 0.0 Ω/squ and an average transmission of 86% between 400 and 800 nm. A high figure of merit of 367 Ω−1 is reported for the electrodes, which is much higher than that measured for indium tin oxide and reported for other AgNW composites. The AgNW:SWCNT:PEDOT:PSS electrode was used to fabricate low temperature (annealing free) devices demonstrating their potential to function with a range of organic semiconducting polymer:fullerene bulk heterojunction blend systems.

Nanostructuring of p- and n-type skutterudites reaching figures of merit of approximately 1.3 and 1.6, respectively

Thermoelectric (TE) conversion of waste heat into useful electricity demands optimized thermal and electrical transport in the leg material over a wide temperature range. In order to gain a reasonably high figure of merit (ZT) as well as high thermal electric conversion efficiency, various conditions of the starting material were studied: industrially produced skutterudite powders of p-type DDy(Fe1-xCox)(4)Sb-12 (DD: didymium) and n-type (Mm, Sm)(y)Co4Sb12 (Mm: mischmetal) were used. After a rather fast reaction-melting technique, the bulk was crushed and sieved with various strainers in order to obtain particles below the respective mesh sizes, followed by ball-milling under three different conditions. The dependence of the TE properties (after hot pressing) on the micro/nanosized particles, grains and crystallites was investigated. Optimized conditions resulted in an increase of ZT for bulk material to current record-high values: from ZT similar to 1.1 to ZT similar to 1.3 at 775 K for p-type and from ZT similar to 1.0 to ZT similar to 1.6 at 800 K for n-type, resulting in respective efficiencies (300-850 K) of eta > 13% and eta similar to 16%. (C) 2014 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Simultaneous enhancement of electrical conductivity and thermopower in Bi2S3 under hydrostatic pressure

The inverse coupled dependence of electrical conductivity and thermopower on carrier concentration presents a big challenge in achieving a high figure of merit. However, the simultaneous enhancement of electrical conductivity and thermopower can be realized in practice by carefully engineering the electronic band structure. Here by taking the example of Bi2S3, we report a simultaneous increase in both electrical conductivity and thermopower under hydrostatic pressure. Application of hydrostatic pressure enables tuning of electronic structure in such a way that the conductivity effective mass decreases and the density of states effective mass increases. This dependence of effective masses leads to simultaneous enhancement in electrical conductivity and thermopower under n-type doping leading to a huge improvement in the power factor. Also lattice thermal conductivity exhibits very weak pressure dependence in the low pressure range. The large power factor together with low lattice thermal conductivity results in a high ZT value of 1.1 under n-type doping, which is nearly two times higher than the previously reported value. Hence, this pressure-tuned behaviour can enable the development of efficient thermoelectric devices in the moderate to high temperature range. We further demonstrate that similar enhancement can be observed by generating chemical pressure by doping Bi2S3 with smaller iso-electronic elements such as Sb at Bi sites, which can be achieved experimentally.

Factores de riesgo cardiovascular en trabajadores de una institución universitaria Bogotá D.C- Colombia

Introducción: la enfermedad cardiovascular es la primera causa de morbi-mortalidad en los países desarrollados, y en algunos en transición como es el caso de Colombia. Según la Organización Mundial de la Salud, las enfermedades cardiovasculares causan 17.5 millones de muertes en el mundo cada año y representan la mitad de todas las muertes en los Estados Unidos y otros países desarrollados. Objetivo: describir la prevalencia de los factores de riesgo cardiovascular en trabajadores de una Institución Universitaria de la ciudad de Bogotá D.C, con el fin de establecer estrategias de promoción de la salud y prevención de enfermedad cardiovascular. Metodología: estudio descriptivo de corte transversal, a través de una muestra de sujetos voluntarios con libre participación. Los trabajadores que decidieron participar se les aplico un cuestionario y se realizó una muestra de sangre por llenado capilar, empleando la técnica de Química Seca (Reflotrón). Acuden 751 trabajadores. Se utilizo un formato como método para recolección de información del examen físico, resultados de paraclínicos y antecedentes de factores de riesgo cardiovascular. Resultados: se realizo la encuesta a 751 trabajadores de las cuales la media de edad fue de 39,7 años. De la población evaluada el 70% pertenecía al género femenino y 30% al género masculino. El 38,6% presentó dislipidemia (colesterol y/o triglicéridos elevados) ;el 7% de la población presentaba diabetes; en diferentes grados de obesidad 6,2% y en sobrepeso se encontraba el 36,8% ; 11,1% son fumadores; y una cifra elevada del 58,7% llevaba una vida sedentaria. El análisis bivariado permitió identificar la relación entre los factores de riesgo y el tipo de trabajador, El valor obtenido se encuentra dentro del rango de mayor probabilidad según la distribución ji-cuadrado frente al factor de riesgo de dislipidemia y sedentarismo. Conclusión: la prevalencia de factores de riesgo en este estudio ha sido similar a la de otros estudios en demás países occidentales; se observó diferencia significativa en la vida sedentaria. Se notó un incremento de los factores de riesgo para las enfermedades cardiovasculares correlacionándolas con la edad, lo cual permite empezar a adoptar y modificar el estilo de vida para disminuir los riesgos de las enfermedades cardiovasculares.

Facile preparation and thermoelectric properties of Bi₂Te₃ based alloy nanosheet/PEDOT:PSS composite films

Bi2Te3 based alloy nanosheet (NS)/poly(3,4-ethylenedioxythiophene):poly(4-styrenesulfonate) (PEDOT:PSS) composite films were prepared separately by spin coating and drop casting techniques. The drop cast composite film containing 4.10 wt % Bi2Te3 based alloy NSs showed electrical conductivity as high as 1295.21 S/cm, which is higher than that (753.8 S/cm) of a dimethyl sulfoxide doped PEDOT:PSS film prepared under the same condition and that (850-1250 S/cm) of the Bi2Te3 based alloy bulk material. The composite film also showed a very high power factor value, ∼32.26 μWm(-1) K(-2). With the content of Bi2Te3 based alloy NSs increasing from 0 to 4.10 wt %, the electrical conductivity and Seebeck coefficient of the composite films increase simultaneously.

Electronic structure and physical properties of Heusler compounds for thermoelectric and spintronic applications

This thesis focuses on synthesis as well as investigations of the electronic structure and properties of Heusler compounds for spintronic and thermoelectric applications.rnThe first part reports on the electronic and crystal structure as well as the mechanical, magnetic, and transport properties of the polycrystalline Heusler compound Co2MnGe. The crystalline structure was examined in detail by extended X-ray absorption fine structure spectroscopy and anomalous X-ray diffraction. The low-temperature magnetic moment agrees well with the Slater-Pauling rule and indicates a half-metallic ferromagnetic state of the compound, as is predicted by ab-initio calculations. Transport measurements and hard X-ray photoelectron spectroscopy (HAXPES) were performed to explain the electronic structure of the compound.rnA major part of the thesis deals with a systematical investigation of Heusler compounds for thermoelectric applications. Few studies have been reported on thermoelectric properties of p-type Heusler compounds. Therefore, this thesis focuses on the search for new p-type Heusler compounds with high thermoelectric efficiency. The substitutional series NiTi1−xMxSn and CoTi1−xMxSb (where M = Sc, V and 0 ≤ x ≤ 0.2) were synthesized and investigated theoretically and experimentally with respect to electronic structure and transport properties. The results show the possibility to create n-type and p-type thermoelectrics within one Heusler compound. The pure compounds showed n-type behavior, while under Sc substitution the system switched to p-type behavior. A maximum Seebeck coefficient of +230 μV/K (at 350 K) was obtained for NiTi0.26Sc0.04Zr0.35Hf0.35Sn, which is one of the highest values for p-type thermoelectric compounds based on Heusler alloys up to now. HAXPES valence band measurement show massive in gap states for the parent compounds NiTiSn, CoTiSb and NiTi0.3Zr0.35Hf0.35Sn. This proves that the electronic states close to the Fermi energy play a key role for the behavior of the transport properties. Furthermore, the electronic structure of the gapless Heusler compounds PtYSb, PtLaBi and PtLuSb were investigated by bulk sensitive HAXPES. The linear behavior of the spectra close to εF proves the bulk origin of Dirac-cone type density of states. Furthermore, a systematic study on the optical and transport properties of PtYSb is presented. The compound exhibits promising thermoelectric properties with a high figure of merit (ZT = 0.2) and a Hall mobility μh of 300 cm2/Vs at 350 K.rnThe last part of this thesis describes the linear dichroism in angular-resolved photoemission from the valence band of NiTi0.9Sc0.1Sn and NiMnSb. High resolution photoelectron spectroscopy was performed with an excitation energy of hν = 7.938 keV. The linear polarization of the photons was changed using an in-vacuum diamond phase retarder. Noticeable linear dichroism is found in the valence bands and this allows for a symmetry analysis of the contributing states. The differences in the spectra are found to be caused by symmetry dependent angular asymmetry parameters, and these occur even in polycrystalline samples without preferential crystallographic orientation.rnIn summary, Heusler compounds with 1:1:1 and 2:1:1 stoichiometry were synthesized and examined by chemical and physical methods. Overall, this thesis shows that the combination of first-principle calculations, transport measurements and high resolution high energy photoelectron spectroscopy analysis is a very powerful tool for the design and development of new materials for a wide range of applications from spintronic applications to thermoelectric applications.rn

Negative index metamaterials and metaspacers for optical frequencies

Metamaterials are artificial materials that exhibit properties, such as negative index of refraction, that are not possible through natural materials. Due to many potential applications of negative index metamaterials, significant progress in the field has been observed in the last decade. However, achieving negative index at visible frequencies is a challenging task. Generally, fishnet metamaterials are considered as a possible route to achieve negative index in the visible spectrum. However, so far no metamaterial has been demonstrated to exhibit simultaneously negative permittivity and permeability (double-negative) beyond the red region of the visible spectrum. This study is mainly focused on achieving higher operating frequency for low-loss, double-negative metamaterials. Two double-negative metamaterials have been proposed to operate at highest reported frequencies. The first proposed metamaterial is based on the interaction of surface plasmon polaritons of a thin metal film with localized surface plasmons of a metallic array placed close to the thin film. It is demonstrated that the metamaterial can easily be scaled to operate at any frequency in the visible spectrum as well as possibly to the ultraviolet spectrum. Furthermore, the underlying physical phenomena and possible future extensions of the metamaterial are also investigated. The second proposed metamaterial is a modification to the so-called fishnet metamaterial. It has been demonstrated that this ‘modified fishnet’ exhibits two double-negative bands in the visible spectrum with highest operating frequency in the green region with considerably high figure of merit. In contrast to most of the fishnet metamaterials proposed in the past, behavior of this modified fishnet is independent of polarization of the incident field. In addition to the two negative index metamaterials proposed in this study, the use of metamaterial as a spacer, named as metaspacer, is also investigated. In contrast to naturally available dielectric spacers used in microfabrication, metaspacers can be realized with any (positive or negative) permittivity and permeability. As an example, the use of a negative index metaspacer in place of the dielectric layer in a fishnet metamaterial is investigated. It is shown that fishnet based on negative index metaspacer gives many improved optical properties over the conventional fishnet such as wider negative index band, higher figure of merit, higher optical transmission and stronger magnetic response. In addition to the improved properties, following interesting features were observed in the metaspacer based fishnet metamaterial. At the resonance frequency, the shape of the permeability curve was ‘inverted’ as compared to that for conventional fishnet metamaterial. Furthermore, dependence of the resonance frequency on the fishnet geometry was also reversed. Moreover, simultaneously negative group and phase velocities were observed in the low-loss region of the metaspacer based fishnet metamaterial. Due to interesting features observed using metaspacer, this study will open a new horizon for the metamaterial research.

Fisheries Department Annual Report 1969

During the year 1969, the fishing industry maintained a rate of increase that had been witnessed in the three previous years. The total catch landed was estimated at 125300 metric tons, valued at shs 130,500,000/-at the lakeside,and about shs 260,000,000/-in the retail market. This was an increase of 16,900 metric tons over the 1968 figure. The largest increases again came from the Lake Kyoga area, where the Nile Perch and the introduced Tilapia species are still expanding. Large numbers of fishermen from other regions (i.e. from Lake Victoria) moved to Lake Kyoga where catches were high and remunerative. This intensified fishing on this lake, resulting in the high figure of catches recorded. As in the previous year, there was a marked increase in the use of large-mesh gill-nets for catching Nile Perch and Tilapia. Individual Tilapia nilotica of up to 5 kg were quite common, and Nile Perch weighing over 50 kg were also regularly taken. The marketing and distribution side of the industry was as active as ever: 87 people took out specific licences, and 640 fishmongers were licensed by different urban authorities. Elsewhere in the Districts, 7,950 fishmongers were licensed. Host of the fish landed was consumed within Uganda and exports accounted for dnly a very small fraction of the market, mainly composed of frozen fiilets to Kenyai and salted fish to the Republic of the Congo. Kampala market was the most important one, serving also as a central market from where fishmongers bought fish for distribution to rural areas.

Investigation of high-efficiency Wireless Power Transfer criteria of resonantly-coupled loops and dipoles through analysis of the figure of merit

The efficiency of a Wireless Power Transfer (WPT) system is greatly dependent on both the geometry and operating frequency of the transmitting and receiving structures. By using Coupled Mode Theory (CMT), the figure of merit is calculated for resonantly-coupled loop and dipole systems. An in-depth analysis of the figure of merit is performed with respect to the key geometric parameters of the loops and dipoles, along with the resonant frequency, in order to identify the key relationships leading to high-efficiency WPT. For systems consisting of two identical single-turn loops, it is shown that the choice of both the loop radius and resonant frequency are essential in achieving high-efficiency WPT. For the dipole geometries studied, it is shown that the choice of length is largely irrelevant and that as a result of their capacitive nature, low-MHz frequency dipoles are able to produce significantly higher figures of merit than those of the loops considered. The results of the figure of merit analysis are used to propose and subsequently compare two mid-range loop and dipole WPT systems of equal size and operating frequency, where it is shown that the dipole system is able to achieve higher efficiencies than the loop system of the distance range examined.

Moving forwards with the aim of going backwards fast : high performance rowing as a learning environment

Background and Purpose: - This paper focuses on the learning culture within the high performance levels of rowing. In doing so, we explore the case of an individual’s learning as he moves across athletic, coaching and administrative functions. This exploration draws on a cultural learning framework and complementary theorisings related to reflexivity. Method - This study makes use of an intellectually, morally and collaboratively challenging approach whereby one member of the research team was also the sole participant of this study. The participant’s careers as a high performance athlete, coach and administrator, coupled with his experience in conducting empirical research presented a rare opportunity to engage in collaborative research (involving degrees of insider and outsider status for each of the research team). We acknowledge that others have looked to combine roles of coach / athlete / administrator with that of researcher however few (if any) have attempted to combine them all in one project. Moreover, coupled with the approach to reflexivity adopted in this study and the authorship contributions we consider this scholarly direction uncommon. Data were comprised of recorded research conversations, a subsequently constructed learning narrative, reflections on the narrative, a stimulated reflective piece from the participant, and a final (re)construction of the participant’s story. Accordingly, data were integrated through an iterative process of thematic analysis. Results - The cultural (i.e., the ways things get done) and structural (e.g., the rules and regulations) properties of high performance rowing were found to shape both the opportunities to be present (e.g., secure a place in the crew) and to learn (e.g., learn the skills required to perform at an Olympic level). However, the individual’s personal properties were brought to bear on re-shaping the constraints such that many limitations could be overcome. In keeping with the theory of learning cultures, the culture of rowing was found to position individuals (a coxswain in this case) differentially. In a similar manner, a range of structural features was found to be important in shaping the cultural and personal elements in performance contexts. For example, the ‘field of play’ was found to be important as a structural feature (i.e., inability of coach to communicate with athletes) in shaping the cultural and personal elements of learning in competition (e.g., positioning the coxswain as an in-boat coach and trusted crewmate). Finally, the cultural and structural elements in rowing appeared to be activated by the participant’s personal elements, most notably his orientation towards quality performance. Conclusion - The participant in this study was found to be driven by the project that he cares about most and at each turn he has bent his understanding of his sport back on itself to see if he can find opportunities to learn and subsequently explore ways to improve performance. The story here emphasises the importance of learner agency, and this is an aspect that has often been missing in recent theorising about learning. In this study, we find an agent using his ‘personal emergent powers to activate the resources in the culture and structure of his sport in an attempt to improve performance. We conclude from this account that this particular high performance rowing culture is one that provided support but nonetheless encouraged those involved, to ‘figure things out’ for themselves – be it as athletes, coaches and/or administrators.