Temperature and composition profile during double-track laser cladding of H13 tool steel

Multi-track laser cladding is now applied commercially in a range of industries such as automotive, mining and aerospace due to its diversified potential for material processing. The knowledge of temperature, velocity and composition distribution history is essential for a better understanding of the process and subsequent microstructure evolution and properties. Numerical simulation not only helps to understand the complex physical phenomena and underlying principles involved in this process, but it can also be used in the process prediction and system control. The double-track coaxial laser cladding with H13 tool steel powder injection is simulated using a comprehensive three-dimensional model, based on the mass, momentum, energy conservation and solute transport equation. Some important physical phenomena, such as heat transfer, phase changes, mass addition and fluid flow, are taken into account in the calculation. The physical properties for a mixture of solid and liquid phase are defined by treating it as a continuum media. The velocity of the laser beam during the transition between two tracks is considered. The evolution of temperature and composition of different monitoring locations is simulated.

The thermal fatigue resistance of vermicular cast iron coupling with H13 steel units by cast-in process

This paper focuses on improving the thermal fatigue resistance on the surface of vermicular cast iron coupling with inserted H13 steel blocks that had different cross sections, by cast-in processing. The microstructure of bionic units was examined by scanning electron microscope. Micro-hardness and thermal fatigue resistance of bionic samples with varied cross sections and spacings were investigated, respectively. Results show that a marked metallurgical bonding zone was produced at interface between the inserted H13 steel block and the parent material - a unique feature of the bionic structure in the vermicular cast iron samples. The micro-hardness of the bionic samples has been significantly improved. Thermal resistance of the samples with the circular cross section was the highest and the bionics sample with spacing of 2 mm spacing had a much longer thermal fatigue life, thus resulting in the improvement for the thermal fatigue life of the bionic samples, due to the efficient preclusion for the generation and propagation of crack at the interface of H13 block and the matrix. Crown Copyright (c) 2010 Published by Elsevier Ltd. All rights reserved.

Cr(N,C) diffusion coating formation on pre-nitrocarburised H13 tool steel

The microstructural processes of Cr(N,C) coating formation by thermoreactive deposition and diffusion (TRD) on pre-nitrocarburised H13 tool steel were studied. Both nitrocarburising and TRD were performed in fluidized bed furnaces at 570 °C. During TRD, chromium was transferred from chromium powder in the fluidized bed, to the nitrocarburised substrates by gas-phase reactions initiated by reaction of HCl gas with the chromium. Addition of 30% H2 to the input inert gas was found to increase the rate of coating formation, although hydrogen reduction resulted in rapid loss of nitrogen to the surface. The reason for the increased rate of coating formation could not be established without further investigation, although several possible explanations have been proposed. It was found that porosity and the formation of an iron nitride ‘cover layer’ during nitrocarburising were the biggest influences on the microstructure of the Cr(N,C) coating. Microstructural characterization of the coatings was performed by scanning electron microscopy (SEM), X-ray diffraction (XRD) and glow discharge optical emission spectroscopy (GDOES).

Pin on disc wear investigation of nitrocarburised H13 tool steel

Nitrocarburised H13 disks were tested in dry, sliding wear against a stationary ruby ball (pin). Three different 4 h nitrocarburising treatments were compared, using N2/NH3/CO2, N2/NH3/natural gas and N2/NH3 gas mixtures, resulting in compound layers of varying thickness, hardness, porosity and oxide morphology. During mild, oxidative wear, with the formation of abrasive wear debris, the most brittle and oxidised surfaces performed poorly. Polishing to a bright, reflective finish greatly reduced wear. However, the N2/NH3/CO2 sample also frequently maintained a 'very mild' wear regime, owing to the formation of a protective film between the wear surfaces, and resulting in a lowering of the friction coefficient. This treated surface was porous and covered in a complex layer of coarse oxide+epsi-carbonitride. Nitrocarburised samples and wear tracks were characterised by optical microscopy, SEM, atomic force microscopy and stylus profilometry.

Tratamento superficial DUPLEX com TiN e CrN de aços ferramenta da classe AISI H13 para matrizes de injeção de ligas de alumínio

Este trabalho apresenta um estudo de camada “duplex” em aços para trabalho à quente da classe AISI H13, com enfoque em matrizes de injeção de ligas de alumínio, visando otimizar a vida das matrizes atuando tanto sobre os mecanismos de ataque superficial da matriz pelo alumínio como sobre a formação de trincas por fadiga térmica. O tratamento duplex consistiu em nitretação à plasma, com gás contendo 5% de nitrogênio e diferentes parâmetros de tempos e temperaturas, sendo as amostras posteriormente revestidas com nitreto de titânio (TiN) ou nitreto de cromo (CrN). As camadas nitretadas foram avaliadas através de análises metalográficas, perfis de dureza e difração de raios X, buscando caracterizar e qualificar a camada nitretada. Tendo sido observado na difração de raios X a presença de camada de compostos (nitretos de ferro ε e γ’) mesmo com a utilização de gás pobre em nitrogênio, foram também avaliados substratos nitretados sem a remoção mecânica dos nitretos e com um polimento para remoção destes antes da deposição. A rugosidade dos substratos nitretados com e sem a realização do polimento mecânico também foram determinados, buscando relação deste parâmetro com os resultados obtidos. O conjunto camada nitretada e depósitos (TiN ou CrN) com e sem o polimento mecânico após-nitretação foram avaliados em termos de adesão com ensaios de indentação Rockwell C com análise em microscopia eletrônica de varredura (qualitativamente) e com o teste do risco (quantitativamente) avaliando tanto as cargas críticas para a falha do filme como o modo de falha também em microscopia eletrônica de varredura. Além disso, foram realizados testes de fadiga térmica em banho de alumínio para simulação e avaliação do desempenho da camada “duplex” em condições de trabalho, bem como foram testadas duas condições de nitretação com TiN ou CrN em regime industrial. Os resultados mostram ganhos de adesão crescentes com o aumento dos tempos e das temperaturas de nitretação, além de maiores ganhos com a remoção mecânica (polimento) do substrato nitretado antes da deposição dos filmes. O comportamento, frente às condições de trabalho também foi superior para condições de nitretação com maiores tempos e temperaturas, tanto nos ensaios de laboratório com nos testes em regime industrial.

Nitretação de um aço H13 a baixas pressões em um equipamento IP35L/TECVAC

O tratamento duplex de nitretação a plasma e posterior deposição de TiN pode proporcionar um aumento na vida útil de ferramentas revestidas, já que a camada nitretada garante uma melhor adesão e maior capacidade de sustentação de carga. Essa melhoria ocorre desde que não haja a formação de uma camada contínua de nitretos de ferro, visto que esta é extremamente frágil, podendo causar o lascamento do filme protetor. A possibilidade de integração da nitretação a baixas pressões e posterior deposição de TiN em um processo contínuo se mostra interessante, pois possibilita a nitretação sem formação de camada de nitretos de ferro, eliminando assim uma etapa de polimento, diminuindo o grau de impurezas do revestimento e o tempo de processamento como um todo. O objetivo desse trabalho é o estudo dos parâmetros de processo mais adequados para a nitretação a baixas pressões de um aço de trabalho a quente H13, de modo a preparar o substrato de forma efetiva para uma posterior deposição de TiN. Diferentes temperaturas (faixa de 400-530ºC), pressões e composições gasosas (misturas de N2, N2 + Ar e N2+H2) foram avaliadas por microscopia ótica, testes de microdureza e difração de raios X. Buscou-se a melhor condição de nitretação, caracterizada pela camada de difusão mais profunda, maior dureza superficial e não aparecimento de uma camada de nitretos de ferro Os resultados indicam que adições de argônio e hidrogênio não resultam na melhor condição de nitretação do aço H13, e que outros parâmetros que não haviam sido considerados como importantes, como rotação das amostras e proteção dos termopares com miçangas, têm grande efeito indireto no tamanho da camada nitretada. O melhor resultado obtido foi com os parâmetros de: temperatura 450ºC, pressão total de N2 de 2x10-3 mbar, termopares protegidos com miçangas, árvore de sustentação das amostras girando a duas e meia revoluções por minuto e filamentos de tungstênio novos.

Enhanced corrosion resistance of AISI H13 steel treated by nitrogen plasma immersion ion implantation

Electrochemical corrosion measurements of AISI H13 steel treated by Pill process in 3.5% (wt) NaCl solution were investigated. So far the corrosion behavior of AISI H 13 steel by Pill has not been studied. The electrochemical results are correlated with the surface morphology, nitrogen content and hardness of the nitride layer. Ion implantation of nitrogen into H 13 steel was carried out by Pill technique. SEM examination revealed a generalized corrosion and porosity over all analyzed sample surfaces. Penetration of nitrogen reaching more than 20 gm was achieved at 450 degrees C and hardness as high as 1340 HV (factor of 2.7 enhancement over standard tempered and annealed H 13) was reached by a high power, 9 h Pill treatment. The corrosion behavior of the samples was studied by potentiodynamic polarization method. The noblest corrosion behavior was observed for the samples treated by PIII at 450 degrees C, during 9 h. Anodic branches of polarization curves of PIII processed samples show a passive region associated with the formation of a protective film. The passive region current density of PIII treated H13 samples (3.5 x 10(-6) A/cm(2)) is about 270 times lower than the one of untreated specimens, which demonstrates the higher corrosion resistance for the Pill treated H 13 samples. (c) 2007 Elsevier B.V. All rights reserved.

Effects of the high temperature plasma immersion ion implantation (PIII) of nitrogen in AISI H13 steel

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Plasma immersion ion implantation of nitrogen into H13 steel under moderate temperatures

Ion implantation of nitrogen into samples of tempered and quenched H13 steel was carried out by plasma immersion technique. A glow discharge plasma of nitrogen species was the ion source and the negative high voltage pulser provided 10-12 kV, 60 mu s duration and 1.0-2.0 kHz frequency, flat voltage pulses. The temperatures of the samples remained between 300 and 450 degrees C, sustained solely by the ion bombardment. In some of the discharges, we used a N-2 + H-2 gas mixture with 1:1 ratio. PIII treatments as long as 3, 6, 9 and up to 12 h were carried out to achieve as thickest treated layer as possible, and we were able to reach over 20 mu m treated layers, as a result of ion implantation and thermal (and possibly radiation enhanced) diffusion. The nitrogen depth profiles were obtained by GDOS (Glow Discharge Optical Spectroscopy) and the exact composition profiles by AES (Auger Electron Spectroscopy). The hardness of the treated surface was increased by more than 250%, reaching 18.8 GPa. No white layer was seen in this case. A hardness profile was obtained which corroborated a deep hardened layer, confirming the high efficacy of the moderate temperature PIII treatment of steels. (c) 2005 Elsevier B.V. All rights reserved.

Efeito da implantação iônica por imersão em plasma no aço ferramenta tipo H13

Pós-graduação em Engenharia Mecânica - FEG

Nanosized precipitates in H13 tool steel low temperature plasma nitriding

A comprehensive study of pulsed nitriding in AISI H13 tool steel at low temperature (400 degrees C) is reported for several durations. X-ray diffraction results reveal that a nitrogen enriched compound (epsilon-Fe2-3N, iron nitride) builds up on the surface within the first process hour despite the low process temperature. Beneath the surface, X-ray Wavelength Dispersive Spectroscopy (WDS) in a Scanning Electron Microscope (SEM) indicates relatively higher nitrogen concentrations (up to 12 at.%) within the diffusion layer while microscopic nitrides are not formed and existing carbides are not dissolved. Moreover, in the diffusion layer, nitrogen is found to be dispersed in the matrix and forming nanosized precipitates. The small coherent precipitates are observed by High-Resolution Transmission Electron Microscopy (HR-TEM) while the presence of nitrogen is confirmed by electron energy loss spectroscopy (EELS). Hardness tests show that the material hardness increases linearly with the nitrogen concentration, reaching up to 14.5 GPa in the surface while the Young Modulus remains essentially unaffected. Indeed, the original steel microstructure is well preserved even in the nitrogen diffusion layer. Nitrogen profiles show a case depth of about similar to 43 mu m after nine hours of nitriding process. These results indicate that pulsed plasma nitriding is highly efficient even at such low temperatures and that at this process temperature it is possible to form thick and hard nitrided layers with satisfactory mechanical properties. This process can be particularly interesting to enhance the surface hardness of tool steels without exposing the workpiece to high temperatures and altering its bulk microstructure. (c) 2012 Elsevier B.V. All rights reserved.

Influence of HSM cutting parameters on the surface integrity characteristics of hardened AISI H13 steel

The purpose of this study is to evaluate the influence of the cutting parameters of high-speed machining milling on the characteristics of the surface integrity of hardened AISI H13 steel. High-speed machining has been used intensively in the mold and dies industry. The cutting parameters used as input variables were cutting speed (v c), depth of cut (a p), working engagement (a e) and feed per tooth (f z ), while the output variables were three-dimensional (3D) workpiece roughness parameters, surface and cross section microhardness, residual stress and white layer thickness. The subsurface layers were examined by scanning electron and optical microscopy. Cross section hardness was measured with an instrumented microhardness tester. Residual stress was measured by the X-ray diffraction method. From a statistical standpoint (the main effects of the input parameters were evaluated by analysis of variance), working engagement (a e) was the cutting parameter that exerted the strongest effect on most of the 3D roughness parameters. Feed per tooth (f z ) was the most important cutting parameter in cavity formation. Cutting speed (v c) and depth of cut (a p) did not significantly affect the 3D roughness parameters. Cutting speed showed the strongest influence on residual stress, while depth of cut exerted the strongest effect on the formation of white layer and on the increase in surface hardness.

Wear mechanisms and microstructure of pulsed plasma nitrided AISI H13 tool steel

AISI H13 tool steel discs were pulsed plasma nitrided during different times at a constant temperature of 400 °C. Wear tests were performed in order to study the acting wear mechanisms. The samples were characterized by X-ray diffraction, scanning electron microscopy and hardness measurements. The results showed that longer nitriding times reduce the wear volumes. The friction coefficient was 0.20 ± 0.05 for all tested conditions and depends strongly on the presence of debris. After wear tests, the wear tracks were characterized by optical and scanning electron microscopy and the wear mechanisms were observed to change from low cycle fatigue or plastic shakedown to long cycle fatigue. These mechanisms were correlated to the microstructure and hardness of the nitrided layer.

Substitution-Modulated Anticancer Activity of Half-Sandwich Ruthenium(II) Complexes with Heterocyclic Ancillary Ligands

Ten new organometallic half-sandwich ruthenium complexes with heterocyclic ligands have been synthesized (H1-H10). The substituents on the ancillary heterocyclic ligands were varied to understand the effect of substitution on anticancer activity. The crystallographic characterization of five complexes confirms that they adopt three-legged piano-stool structures and are stabilized by intramolecular hydrogen bonding. Complexes H2 and H3 also exhibit halogen bonding in the solid state. In aqueous media, the complexes form dinuclear ruthenium species. Complex H1 with a noncytotoxic heterocycle, 6-fluoro-2-mercaptobenzothiazole, and complex H11 with the unsubstituted 2-mercaptobenzothiazole are the most active against A2780 and KB cell lines. The substitution of the H atoms on the ancillary ligand with Cl or Br atoms leads to a decrease in the anticancer activity. With the exception of fluorine-substituted H5, the complexes with mercaptobenzoxazole (H6-H9) are inactive against all of the tested cell lines. Ruthenium complexes with mercaptonaphthimidazole (H10) and mercaptobenzimidazole (H13) do not show any anticancer activity. The active complexes show a biphasic melting curve when incubated with calf thymus (CT) DNA. These complexes only inhibit thioredoxin reductase (TrxR) enzyme activity to a small extent. The substitution of hydrogen atoms with fluorine atoms in the aromatic heterocyclic ligands on organometallic half-sandwich ruthenium complexes has the most beneficial effect on their anticancer activity.