Long-Term Evolution Of Delayed Ettringite And Gypsum In Portland Cement Mortars Under Sulfate Erosion

The magnitude evolution of ettringite and gypsum in hydrated Portland cement mortars due to sulfate attack was detected by X-ray powder diffraction. The influences of sulfate concentration and water-to-cement ratio on the evolution of ettringite and gypsum were investigated. Experimental results show that the magnitude of ettringite formation in sodium sulfate solution follows a three-stage process, namely, the 'penetration period', 'enhance period of strength', and 'macro-crack period'. The cracking of concrete materials is mainly attributed to the effect of ettringite. The gypsum formations occurred in two stages, the 'latent period' and the 'accelerated period'. The gypsum formation including ettringite formation was relative to the linear expansion of mortars to some extend. Both water-to-cement ratio and sulfate concentration play important roles in the evolution of ettringite and gypsum. (C) 2008 Elsevier Ltd. All rights reserved.

Determining gypsum growth temperatures using monophase fluid inclusions-Application to the giant gypsum crystals of Naica, Mexico

Determining the formation temperature of minerals using fluid inclusions is a crucial step in understanding rock-forming scenarios. Unfortunately, fluid inclusions in minerals formed at low temperature, such as gypsum, are commonly in a metastable monophase liquid state. To overcome this problem, ultra-short laser pulses can be used to induce vapor bubble nucleation, thus creating a stable two-phase fluid inclusion appropriate for subsequent measurements of the liquid-vapor homogenization temperature, T-h. In this study we evaluate the applicability of T-h data to accurately determine gypsum formation temperatures. We used fluid inclusions in synthetic gypsum crystals grown in the laboratory at different temperatures between 40 degrees C and 80 degrees C under atmospheric pressure conditions. We found an asymmetric distribution of the T-h values, which are systematically lower than the actual crystal growth temperatures, T-g; this is due to (1) the effect of surface tension on liquid-vapor homogenization, and (2) plastic deformation of the inclusion walls due to internal tensile stress occurring in the metastable state of the inclusions. Based on this understanding, we have determined growth temperatures of natural giant gypsum crystals from Naica (Mexico), yielding 47 +/- 1.5 degrees C for crystals grown in the Cave of Swords (120 m below surface) and 54.5 +/- 2 degrees C for giant crystals grown in the Cave of Crystals (290 m below surface). These results support the earlier hypothesis that the population and the size of the Naica crystals were controlled by temperature. In addition, this experimental method opens a door to determining the growth temperature of minerals forming in low-temperature environments.

Susceptibility Of strength development by lime in gypsiferous soil-A micro mechanistic study

The role of gypsum on the strength of lime treated soils after a long period of interaction is not well understood yet. The present study is performed to scrutinize the physical and strength behavior of lime treated soil with varying gypsum content. Lime and gypsum contents varying from 0 to 6% are considered in the present study for curing periods up to 28 days. To understand the long-term effects, the work has been extended up to 365 days, particularly with the use of 6% lime content and varying gypsum contents. Atterberg's limits turned out to be marginally affected by cation exchange. Unconfined compressive strength behavior of lime treated soil varies considerably with gypsum content and curing period. However, trivial alteration in strength is observed in the soil treated with lower lime content (up to 4%) and gypsum content up to 6%. On the contrary, strength of soil-6% lime mixture with addition of varying gypsum content shows acceleration in early strength at 14 days curing period. However, the strength at 28 days of curing declines but regains afterwards for 90 days. The trend at longer curing period for 180 and 365 days is, however, not unique but varies with gypsum contents. An attempt has been made to explain these changes on the basis of the form of gypsum, formation and conversion of reacted compounds (CASHH, CASH, MI and Ettringite). The proposed explanations were supported by detailed characterization through thermal analysis, XRD, SEM and EDAX studies of soil-lime-gypsum mixtures. (C) 2015 Elsevier B.V. All rights reserved.

盐岩地层套管蠕变荷载试验及其数值分析

中原油田在钻遇盐岩层的油水井中,某些区块套管的损坏率高达65%,盐岩层蠕变是套管损坏的一个重要原因.通过对6块盐岩岩心进行地下条件的蠕变模拟试验,得出了盐岩层的蠕变规律和特征参数,建立了套管承受外载的有限元计算模型,并编制了计算程序.利用所编制的软件对中原油田某口井的套管蠕变载荷进行了数值模拟计算.结果表明,作用在套管上的径向载荷与相位角和蠕变时间有关,并且蠕变条件下套管的最大载荷超过原地应力10%左右.

Preservation of York Minster historic limestone by hydrophobic surface coatings

Magnesian limestone is a key construction component of many historic buildings that is under constant attack from environmental pollutants notably by oxides of sulfur via acid rain, particulate matter sulfate and gaseous SO 2 emissions. Hydrophobic surface coatings offer a potential route to protect existing stonework in cultural heritage sites, however, many available coatings act by blocking the stone microstructure, preventing it from 'breathing' and promoting mould growth and salt efflorescence. Here we report on a conformal surface modification method using self-assembled monolayers of naturally sourced free fatty acids combined with sub-monolayer fluorinated alkyl silanes to generate hydrophobic (HP) and super hydrophobic (SHP) coatings on calcite. We demonstrate the efficacy of these HP and SHP surface coatings for increasing limestone resistance to sulfation, and thus retarding gypsum formation under SO/H O and model acid rain environments. SHP treatment of 19th century stone from York Minster suppresses sulfuric acid permeation.

Pore formation during dehydration of polycrystalline gypsum observed and quantified in a time-series synchrotron radiation based X-ray micro-tomography experiment

We conducted an in-situ X-ray micro-computed tomography heating experiment at the Advanced Photon Source (USA) to dehydrate an unconfined 2.3 mm diameter cylinder of Volterra Gypsum. We used a purpose-built X-ray transparent furnace to heat the sample to 388 K for a total of 310 min to acquire a three-dimensional time-series tomography dataset comprising nine time steps. The voxel size of 2.2 μm3 proved sufficient to pinpoint reaction initiation and the organization of drainage architecture in space and time. We observed that dehydration commences across a narrow front, which propagates from the margins to the centre of the sample in more than four hours. The advance of this front can be fitted with a square-root function, implying that the initiation of the reaction in the sample can be described as a diffusion process. Novel parallelized computer codes allow quantifying the geometry of the porosity and the drainage architecture from the very large tomographic datasets (20483 voxels) in unprecedented detail. We determined position, volume, shape and orientation of each resolvable pore and tracked these properties over the duration of the experiment. We found that the pore-size distribution follows a power law. Pores tend to be anisotropic but rarely crack-shaped and have a preferred orientation, likely controlled by a pre-existing fabric in the sample. With on-going dehydration, pores coalesce into a single interconnected pore cluster that is connected to the surface of the sample cylinder and provides an effective drainage pathway. Our observations can be summarized in a model in which gypsum is stabilized by thermal expansion stresses and locally increased pore fluid pressures until the dehydration front approaches to within about 100 μm. Then, the internal stresses are released and dehydration happens efficiently, resulting in new pore space. Pressure release, the production of pores and the advance of the front are coupled in a feedback loop.

Petrography of gypsum-bearing facies of the Codó Formation (Late Aptian), Northern Brazil

Neste trabalho, é apresentado um estudo original e detalhado enfocando os aspectos petrográficos dos evaporitos de depósitos aptianos superiores expostos no sul e leste da Bacia de São Luís-Grajaú. O objetivo é o estabelecimento de critérios que permitam distinguir entre evaporitos primários e secundários, além da reconstrução de sua evolução pós-deposicional. Sete fases de evaporitos foram reconhecidas: 1. gipsita em chevron; 2. gipsita ou anidrita nodular a lenticular; 3. gipsita fibrosa a acicular; 4. gipsita em mosaico; 5. gipsita brechada a gipsarenito; 6. anidrita ou gipsita pseudo-nodular; e 7. gipsita em rosetas. As três primeiras fases apresentam características petrográficas condizentes com origem primária. Agipsita fibrosa a acicular e a gipsita em mosaico foramformadas por substituições de gipsita primária, com origem provável nos estágios iniciais da diagenêse, portanto ainda sob influência do ambiente deposicional. Estas morfologias de gipsita estão relacionadas com a fácies de evaporito laminado, tendo sido formadas por substituição, porém sem afetar a estruturação primária. A gipsita ou anidrita pseudo-nodular originou-se pela mobilização de soluções sulfatadas durante ou após soterramento, provavelmente associada à halocinese. A gipsita em rosetas, que intercepta todas as outras variedades de gipsita, representa o ultimo estágio de formação de evaporitos na área de estudo, tendo resultado de soluções intraestratais ou de águas superficiais durante intemperismo.

The solubility of gypsum in calcareous soils

Three gypsiferous-calcareous soils from the Al-Hassa Oasis in Saudi Arabia were examined to determine the conditions under which dissolution of gypsum could be hindered by the formation of coatings of calcite during leaching. Batch extraction with water of a sandy clay loam, a sandy clay and a sandy loam containing 40, 26 and 5% gypsum and 14, 12 and 13% calcite respectively was followed by chemical analysis of the extracts, SEM examination and XRD and EDX microprobe analysis. Extraction in closed centrifuge tubes for I h or 5 h showed that initially gypsum dissolved to give solutions near to equilibrium but then in the sandy clay loam, between one quarter and one third of the gypsum could not dissolve. In the sandy clay about one fifth of the gypsum could not dissolve with none remaining in the sandy loam. All the extracts were close to equilibrium with calcite. SEM and EDX examination showed that coatings of calcite had formed on the gypsum particles. The sandy clay loam was also extracted using an open system in which either air or air +1% CO2 was bubbled through the suspensions for 1 h with stirring. The gypsum dissolved more rapidly and all of the gypsum dissolved. Thus, where the rate of dissolution of gypsum was rapid, calcite did not manage to cover the gypsum surfaces probably because the surface was being continuously removed. Slower leaching conditions in the field are likely to be conducive to the formation of coatings and less dissolution of gypsum. (c) 2006 Elsevier B.V. All rights reserved.

Sources of sulphur in gypsiferous sediments and crusts and pathways of gypsum redistribution in southern Tunisia

Southern Tunisia contains one of the most extensive gypsum accumulations in Africa comprising Triassic, Cretaceous, Eocene and Mio-Pliocene marine evaporites, spring deposits, playa sediments, aeolian sands and gypsum crusts. Sulphur isotope analysis (delta(34)S) of bedrock samples, groundwater, playa brines, playa sediments, and gypsiferous crusts provides insight into the sources of gypsum in the region and sheds light on the processes that lead to gypsum crust formation. Results Suggest that recycling of marine gypsum is the most likely source of the sulphate in the groundwater, playa sediments and crusts. The low PS values found in Eocene and Mio-Pliocene samples suggest that this recycling has been going on for millions of years. Though bedrock appears to be the ultimate source of the gypsum in the crusts, transport of this sulphate to playas, concentration therein, and subsequent dispersal across the landscape by aeolian processes provides the most likely pathway for surticial gypsum crust formation. Comparison of these results with those from Australia, Chile and Namibia suggests that, although the source of the sulphur varies from region to region, the processes of surficial crust formation appear to be similar. Copyright (C) 2004 John Wiley Sons, Ltd.

Isotopic analyses of DSDP Hole 45-395A samples from veins containing gypsum (Table 1)

Gypsum and halite crystals, together with saponite and phillipsite, were found in a vein in a basalt sill 625 m below the sea floor at DSDP Site 395A, located 190 km west of the crest of the Mid-Atlantic Ridge. The delta34S value of the gypsum (+19.4?) indicates a seawater source for the sulfate. The delta18O values of the saponite (+19.9?) and phillipsite (+18.1?) indicate either formation from normal seawater at about 55°C or formation from delta18O-depleted seawater at a lower temperature. The gypsum (which could be secondary after anhydrite) was formed by reaction between Ca[2+] released from basalt and SO4[2-] in circulating seawater. The halite could have formed when water was consumed by hydration of basalt under conditions of extremely restricted circulation. A more probable mechanism is that the gypsum was originally precipitated as anhydrite at temperatures above 60°C. As the temperature dropped the anhydrite converted to gypsum. The conversion would consume water, which could cause halite precipitation, and would cause an increase in the volume of solids, which would plug the vein and prevent subsequent dissolution of the halite.

(Table 1) Gypsum, pyrite and glauconite at DSDP Hole 36-329

Authigenic gypsum, pyrite, and glauconite are disseminated throughout an unusually long (346 m) Miocene section of mixed biogenic carbonate and diatomaceous ooze drilled on the Falkland Plateau at DSDP Site 329 (water depth, 1519 m). The present organic carbon content of the sediment is low, ranging between 0.1 and 0.7%. Gypsum occurs as euhedral single or twinned crystals of selenite up to 5 mm in diameter, sometimes in the form of gypsum rosettes. These crystals are intact and unabraded, comprising up to 4% of the washed sample. The authigenic nature of the gypsum is demonstrated by the presence of diatoms and radiolarians embedded within the gypsum crystals. The gypsum co-occurs with pyrite and glauconite in these samples. The pyrite occurs as framboids, foraminiferal infillings, rods, and granular sheetlike masses composed of pyrite octahedra. The glauconite occurs as foraminiferal infillings and as free grains. The gypsum and pyrite were identified by energy-dispersive X-ray analysis and scanning electron micrographs. Some of the gypsum has grown on pyrite, indicating that it precipitated after the pyrite, perhaps in response to a change in pH conditions. The formation of the mineral suite can be explained by current models of in situ sulfide and sulfate precipitation coincident with diagenesis and oxidation of much of the original organic carbon.

(Table 1) Porewater analysis with respect to gypsum from different ODP holes

The stability of gypsum in marine sediments has been investigated through the calculation of its saturation index at the sediment in situ temperature and pressure, using the entire ODP/IODP porewater composition database (14416 samples recovered from sediments collected during 95 ODP and IODP Legs). Saturation is reached in sediment porewaters of 26 boreholes drilled at 23 different sites, during 12 ODP/IODP Legs. As ocean bottom seawater is largely undersaturated with respect to gypsum, the porewater Ca content or its SO4 concentration, or both, must increase in order to reach equilibrium. At several sites equilibrium is reached either through the presence of evaporitic gypsum layers found in the sedimentary sequence, and/or through a salinity increase due to the presence of evaporitic brines with high concentrations of Ca and SO4. Saturation can also be reached in porewaters of seawater-like salinity (~ 35 per mil), provided sulfate reduction is limited. In this case, saturation is due to the alteration of volcanogenic material which releases large amounts of Ca to the porewaters, where the Ca concentration can reach 55 times its seawater value as for example at ODP Leg 134 site 833. At a few sites, saturation is reached in hydrothermal environments, or as a consequence of the alteration of the basaltic basement. In addition to the well known influence of brines on the formation of gypsum, these results indicate that the alteration of sediments rich in volcanogenic material is a major process leading to gypsum saturation in marine sediment porewaters. Therefore, the presence of gypsum in ancient and recent marine sediments should not be systematically interpreted as due to hypersaline waters, especially if volcanogenic material is present.

Isotope characterization and estimated temperature of formation of calcite veins in ODP Sites 124-768 and 124-770 (Table 1)

Secondary carbonate minerals were recovered within the basalts at both ODP Sites 768 and 770 in the Sulu and Celebes seas. Petrographic and X-ray diffraction analyses indicate that the carbonates are calcites. Other alteration products recognized in the thin sections are smectites, iron oxides, and gypsum. The 13C values of carbonates from both sites range from 1.6 per mil to 2.3 per mil, which are indicative of inorganic carbonate formation with no contributions from 13C-depleted sources such as oxidized organic carbon or methane. The oxygen isotopes at Site 770 range from 30.8 per mil to 31.6 per mil, which indicates a pervasive circulation of cold seawater (9° to 12°C) during alteration of the Celebes Sea basalts. In contrast, carbonates associated with Site 768 basalts have less positive d18O values (21.0 per mil to 27.3 per mil). A lighter 18O isotopic signature indicates the formation of secondary calcite at either higher temperatures or in a system closed to seawater. The rapidly deposited pyroclastic flows at Site 768 would have limited water access to the crust very soon after its formation, which leads us to speculate that the carbonates in the Sulu Sea basalts were formed by isotopically modified fluids resulting from basalt alteration in a closed system.