Geophysical and geochemical survey of a large marine pockmark on the Malin Shelf, Ireland

Marine pockmarks are a specific type of seabed geological setting resembling craters or pits and are considered seabed surface expressions of fluid flow in the subsurface. A large composite pockmark on the Malin Shelf, off the northern coast of Ireland was surveyed and ground truthed to assess its activity and investigate fluid related processes in the subsurface. Geophysical (including acoustic and electromagnetic) data confirmed the subsurface presence of signatures typical of fluids within the sediment. Shallow seismic profiling revealed a large shallow gas pocket and typical gas related indicators such as acoustic blanking and enhanced reflectors present underneath and around the large pockmark. Sulphate profiles indicate that gas from the shallow reservoir has been migrating upwards, at least recently. However, there are no chimney structures observed in the sub-bottom data and the migration pathways are not apparent. Electromagnetic data show slightly elevated electrical conductivity on the edges of the pockmarks and a drop below regional levels within the confines of the pockmark, suggesting changes in physical properties of the sediment. Nuclear Magnetic Resonance (NMR) experiments were employed to characterize the organic component of sediments from selected depths. Very strong microbial signatures were evident in all NMR spectra but microbes outside the pockmark appear to be much more active than inside. These observations coincide with spikes in conductivity and the lateral gas bearing body suggesting that there is an increase in microbial activity and biomass when gas is present.

Cartografia geoquímica da ilha de Santiago com uma densidade de amostragem média/baixa

A ilha de Santiago é a maior do arquipélago de Cabo Verde, apresenta uma área de 991 km2, com um comprimento e largura máximos de 54,9 km e 29 km, respectivamente, e 1392 m de maior altitude. As condições climáticas e a erosão são alguns dos problemas naturais do arquipélago de Cabo Verde. Além disso, a intervenção humana no ambiente superficial revela-se muitas vezes inadequada e com forte impacto. A construção em solos com aptidão agrícola ou florestal, as actividades industriais, a deposição de materiais sólidos ou líquidos de forma inadequada, as práticas agrícolas incorrectas e intensivas, o uso abusivo de pesticidas e fertilizantes, a rega com água contaminada, a sobreexploração de aquíferos que levam muitas vezes à salinização, etc. têm enorme impacto em termos de contaminação de solos, águas superficiais e subterrâneas nas áreas envolventes. Por conseguinte, o conhecimento da variabilidade geoquímica natural é fundamental para a resolução de questões de índole económica, ambiental e de ordenamento do território, médica, e jurídica. A necessidade de construir uma base de dados de geoquímica georeferenciada que caracterize o ambiente superficial da ilha de Santiago foi a principal motivação para a realização deste estudo. Realizou-se um levantamento geoquímico de 337 amostras de sedimentos de corrente e 249 amostras de solos na ilha de Santiago, tendo sido seguidas as recomendações do Projecto Internacional IGCP 259 não só na fase de amostragem, mas também nas fases seguintes de preparação, análise, tratamento dos dados e elaboração de mapas. Determinaram-se os teores, na fracção < 2 mm, para 36 elementos – 9 elementos maiores (Al, Ca, Fe, K, Mg, Mn, Na, P, Ti) e 27 elementos vestigiais (Ag, As, Au, B, Ba, Bi, Cd, Co, Cr, Cu, Ga, Hg, La, Mo, Ni, Pb, S, Sb, Sc, Se, Sr, Th, Tl, U, V, W, Zn). Efectuou-se ainda a análise textural e estudou-se a composição mineralógica de cerca de 25% das amostras. Analisaram-se, também, 103 amostras de rochas, colhidas nas várias formações da ilha de Santiago, tendo sido determinados os teores de K2O, Na2O, Fe2O3(T), MnO, Sc, Cr, Co, Zn, Ga, As, Br, Rb, Zr, Sb, Cs, Ba, Hf, Ta, W, Th e U e REE, a fim de se fazer uma comparação com os teores destes elementos encontrados nos solos e sedimentos de corrente, averiguando se a sua variação é ou não essencialmente condicionada pela geoquímica da rocha-mãe. Os padrões geoquímicos obtidos através dos mapas de distribuição espacial foram correlacionados com a natureza da rocha mãe, o tipo de solo, e ainda com algumas fontes de contaminação. A interpretação dos resultados foi realizada não só pela observação dos mapas geoquímicos, mas também após análise estatística dos conjuntos de dados obtidos, e apoiada em informação diversa disponível. A utilização da Análise de Componentes Principais permitiu distinguir associações entre elementos químicos, quer de origem geogénica quer antropogénica. Foram ainda elaborados mapas de distribuição espacial de vários índices multielementares de importância ambiental, como o Índice de Acidificação Al/(Ca+Mg+K), Índice de Combi, Índice de Avaliação de Risco Ambiental e Índices de Enriquecimento/Contaminação para vários grupos de elementos considerados como “primary pollutant metals”.

Integração de dados em ambiente SIG para mapeamento de favorabilidade mineral de ouro na ilha cristalina de Rivera (Uruguai)

Guias para exploração mineral são normalmente baseados em modelos conceituais de depósitos. Esses guias são, normalmente, baseados na experiência dos geólogos, em dados descritivos e em dados genéticos. Modelamentos numéricos, probabilísticos e não probabilísticos, para estimar a ocorrência de depósitos minerais é um novo procedimento que vem a cada dia aumentando sua utilização e aceitação pela comunidade geológica. Essa tese utiliza recentes metodologias para a geração de mapas de favorablidade mineral. A denominada Ilha Cristalina de Rivera, uma janela erosional da Bacia do Paraná, situada na porção norte do Uruguai, foi escolhida como estudo de caso para a aplicação das metodologias. A construção dos mapas de favorabilidade mineral foi feita com base nos seguintes tipos de dados, informações e resultados de prospecção: 1) imagens orbitais; 2) prospecção geoquimica; 3) prospecção aerogeofísica; 4) mapeamento geo-estrutural e 5) altimetria. Essas informacões foram selecionadas e processadas com base em um modelo de depósito mineral (modelo conceitual), desenvolvido com base na Mina de Ouro San Gregorio. O modelo conceitual (modelo San Gregorio), incluiu características descritivas e genéticas da Mina San Gregorio, a qual abrange os elementos característicos significativos das demais ocorrências minerais conhecidas na Ilha Cristalina de Rivera. A geração dos mapas de favorabilidade mineral envolveu a construção de um banco de dados, o processamento dos dados, e a integração dos dados. As etapas de construção e processamento dos dados, compreenderam a coleta, a seleção e o tratamento dos dados de maneira a constituírem os denominados Planos de Informação. Esses Planos de Informação foram gerados e processados organizadamente em agrupamentos, de modo a constituírem os Fatores de Integração para o mapeamento de favorabilidade mineral na Ilha Cristalina de Rivera. Os dados foram integrados por meio da utilização de duas diferentes metodologias: 1) Pesos de Evidência (dirigida pelos dados) e 2) Lógica Difusa (dirigida pelo conhecimento). Os mapas de favorabilidade mineral resultantes da implementação das duas metodologias de integração foram primeiramente analisados e interpretados de maneira individual. Após foi feita uma análise comparativa entre os resultados. As duas metodologias xxiv obtiveram sucesso em identificar, como áreas de alta favorabilidade, as áreas mineralizadas conhecidas, além de outras áreas ainda não trabalhadas. Os mapas de favorabilidade mineral resultantes das duas metodologias mostraram-se coincidentes em relação as áreas de mais alta favorabilidade. A metodologia Pesos de Evidência apresentou o mapa de favorabilidade mineral mais conservador em termos de extensão areal, porém mais otimista em termos de valores de favorabilidade em comparação aos mapas de favorabilidade mineral resultantes da implementação da metodologia Lógica Difusa. Novos alvos para exploração mineral foram identificados e deverão ser objeto de investigação em detalhe.

Análises de solos e sedimentos de corrente, nas áreas das usinas de fundição de chumbo do Calabouço (CIEM-CPRM) e de beneficiamento de minério aurífero do Morro do Ouro (Parque Municipal Morro do Ouro), no município de Apiaí - SP

Located in Apiaí, Vale do Ribeira, southern region of São Paulo state, the Usina do Calabouço areas (CIEM / CPRM) and Morro do Ouro (Parque Municipal do Morro do Ouro), were targeted for stud ies due to its old buildings, respectively a foundry in lead ore, called Experimental de Chumbo e Prata (Usina Calabouço), and a gold mine with processing plant of the gold-bearing ore produced there. Nowadays, the areas are used for public visitation, and in both places the rests of the buildings remains. Particularly in the CIEM/CPRM, due to the materials witch was produced before, it can suggest the existence of anomalous amounts of the involved metals (CIEM / CPRM) and possible contaminations by chemical products used in the improvement of the auriferous ore (P. M. Morro do Ouro). These potential contamination were confirmed with geochemical survey of soils and current sediments accomplished in both areas, for the elements arsenic, cadmium, lead, copper, mercury, silver and zinc, which were used as parameters guiding values for soil and groundwater the state of São Paulo (CETESB), and watershed values stipulated by CPRM (poor, background and anomalous), in it rising geochemistry during Folha Apiaí's execution (SG-22-X-B-V).

Grain size analyses, Ca/Ti and other selected elemental ratios from XRF core scanning of sediment cores from the Apulian Margin

An extensive, high-resolution, sedimentological-geochemical survey was done using geo-acoustics, XRF-core scans, ICP-AES, AMS 14C-dating and grain size analyses of sediments in 11 cores from the Gulf of Taranto, the southern Adriatic Sea, and the central Ionian Sea spanning the last 16 cal. ka BP. Comparable results were obtained for cores from the Gallipoli Shelf (eastern Gulf of Taranto), and the southern Adriatic Sea suggesting that the dominant provenance of Gallipoli Shelf sediments is from the western Adriatic mud belt. The 210Pb and 14C-dated high-accumulation-rate sediments permit a detailed reconstruction of climate variability over the last 16 cal. ka BP. Although, the Glacial-Interglacial transition is generally dry and stable these conditions are interrupted by two phases of increased detrital input during the Bølling-Allerød and the late Younger Dryas. The event during the Younger Dryas period is characterized by increased sediment inputs from southern Italian sources. This suggests that run-off was higher in southern- compared to northern Italy. At approximately ~ 7 cal. ka BP, increased detrital input from the Adriatic mud belt, related to sea level rise and the onset of deep water formation in the Adriatic Sea, is observed and is coincident with the end of sapropel S1 formation in the southern Adriatic Sea. During the mid-to-late Holocene we observed millennial-scale events of increased detrital input, e.g. during the Roman Humid Period, and of decreased detrital input, e.g., Medieval Warm Period. These dry/wet spells are consistent with variability in the North Atlantic Oscillation (NAO). A negative state of the NAO and thus a more advanced penetration of the westerlies into the central Mediterranean, that result in wet conditions in the research area concord with events of high detrital input e.g., during the Roman Humid Period. In contrast, a positive state of the NAO, resulting in dry conditions in the Mediterranean, dominated during events of rapid climate change such as the Medieval Warm Period and the Bronze Age.

The Amplifier - v. 16, no. 8

In this issue...Turtle Race, April Fool's Day, American Indians, Anaconda Company, Prudential Scholarship, M Club Smoker, Charles Silberman, Student Poverty

Regolith mass balance inferred from combined mineralogical, geochemical and geophysical studies: Mule Hole gneissic watershed, South India

The aim of this study is to propose a method to assess the long-term chemical weathering mass balance for a regolith developed on a heterogeneous silicate substratum at the small experimental watershed scale by adopting a combined approach of geophysics, geochemistry and mineralogy. We initiated in 2003 a study of the steep climatic gradient and associated geomorphologic features of the edge of the rifted continental passive margin of the Karnataka Plateau, Peninsular India. In the transition sub-humid zone of this climatic gradient we have studied the pristine forested small watershed of Mule Hole (4.3 km(2)) mainly developed on gneissic substratum. Mineralogical, geochemical and geophysical investigations were carried out (i) in characteristic red soil profiles and (ii) in boreholes up to 60 m deep in order to take into account the effect of the weathering mantle roots. In addition, 12 Electrical Resistivity Tomography profiles (ERT), with an investigation depth of 30 m, were generated at the watershed scale to spatially characterize the information gathered in boreholes and soil profiles. The location of the ERT profiles is based on a previous electromagnetic survey, with an investigation depth of about 6 m. The soil cover thickness was inferred from the electromagnetic survey combined with a geological/pedological survey. Taking into account the parent rock heterogeneity, the degree of weathering of each of the regolith samples has been defined using both the mineralogical composition and the geochemical indices (Loss on Ignition, Weathering Index of Parker, Chemical Index of Alteration). Comparing these indices with electrical resistivity logs, it has been found that a value of 400 Ohm m delineates clearly the parent rocks and the weathered materials, Then the 12 inverted ERT profiles were constrained with this value after verifying the uncertainty due to the inversion procedure. Synthetic models based on the field data were used for this purpose. The estimated average regolith thickness at the watershed scale is 17.2 m, including 15.2 m of saprolite and 2 m of soil cover. Finally, using these estimations of the thicknesses, the long-term mass balance is calculated for the average gneiss-derived saprolite and red soil. In the saprolite, the open-system mass-transport function T indicates that all the major elements except Ca are depleted. The chlorite and biotite crystals, the chief sources for Mg (95%), Fe (84%), Mn (86%) and K (57%, biotite only), are the first to undergo weathering and the oligoclase crystals are relatively intact within the saprolite with a loss of only 18%. The Ca accumulation can be attributed to the precipitation of CaCO3 from the percolating solution due to the current and/or the paleoclimatic conditions. Overall, the most important losses occur for Si, Mg and Na with -286 x 10(6) mol/ha (62% of the total mass loss), -67 x 10(6) mol/ha (15% of the total mass loss) and -39 x 10(6) mol/ha (9% of the total mass loss), respectively. Al, Fe and K account for 7%, 4% and 3% of the total mass loss, respectively. In the red soil profiles, the open-system mass-transport functions point out that all major elements except Mn are depleted. Most of the oligoclase crystals have broken down with a loss of 90%. The most important losses occur for Si, Na and Mg with -55 x 10(6) mol/ha (47% of the total mass loss), -22 x 10(6) mol/ha (19% of the total mass loss) and -16 x 10(6) mol/ha (14% of the total mass loss), respectively. Ca, Al, K and Fe account for 8%, 6%, 4% and 2% of the total mass loss, respectively. Overall these findings confirm the immaturity of the saprolite at the watershed scale. The soil profiles are more evolved than saprolite but still contain primary minerals that can further undergo weathering and hence consume atmospheric CO2.

Archaean crustal evolution in eastern Finland : New geochronological and geochemical constraints from the Kuhmo terrain and the Nurmes belt

This thesis summarises the results of four original papers concerning U-Pb geochronology and geochemical evolution of Archaean rocks from the Kuhmo terrain and the Nurmes belt, eastern Finland. The study area belongs to a typical Archaean granite-greenstone terrain, composed of metavolcanic and metasedimentary rocks in generally N-S trending greenstone belts as well as a granitoid-gneiss complex with intervening gneissic and migmatised supracrustal and plutonic rocks. U-Pb data on migmatite mesosomes indicate that the crust surrounding the Tipasjärvi-Kuhmo-Suomussalmi greenstone belt is of varying age. The oldest protolith detected for a migmatite mesosome from the granitoid-gneiss complex is 2.94 Ga, whereas the other dated migmatites protoliths have ages of 2.84 2.79 Ga. The latter protoliths are syngenetic with the majority of volcanic rocks in the adjacent Tipasjärvi-Kuhmo-Suomussalmi greenstone belt. This suggests that the genesis of some of the volcanic rocks within the greenstone belt and surrounding migmatite protoliths could be linked. Metamorphic zircon overgrowths with ages of 2.84 2.81 Ga were also obtained. The non-migmatised plutonic rocks in the Kuhmo terrain and in the Nurmes belt record secular geochemical evolution, typical of Archaean cratons. The studied tonalitic rocks have ages of 2.83 2.75 Ga and they have geochemical characteristics similar to low-Al and high-Al TTD (tonalite-trondhjemite-dacite). The granodiorites, diorites, and gabbros with high Mg/Fe and LILE-enriched characteristics were mostly emplaced between 2.74 2.70 Ga and they exhibit geochemical characteristics typical of Archaean sanukitoid suites. The latest identified plutonic episode took place at 2.70 2.68 Ga, when compositionally heterogeneous leucocratic granitoid rocks, with a variable crustal component, were emplaced. U-Pb data on migmatite leucosomes suggest that leucosome generation may have been coeval with this latest plutonic event. On the basis of available U-Pb and Sm-Nd isotopic data it appears that the plutonic rocks of the Kuhmo terrain and the Nurmes belt do not contain any significant input from Palaeoarchaean sources. A characteristic feature of the Nurmes belt is the presence of migmatised paragneisses, locally preserving primary edimentary structures, with sporadic amphibolite intercalations. U-Pb studies on zircons indicate that the precursors of the Nurmes paragneisses were graywackes that were deposited between 2.71 Ga and 2.69 Ga and that they had a prominent 2.75 2.70 Ga source. Nd isotopic and whole-rock geochemical data for the intercalated amphibolites imply MORB sources. U-Pb data on zircons from the plutonic rocks and paragneisses reveal that metamorphic zircon growth took place at 2.72 2.63 Ga. This was the last tectonothermal event related to cratonisation of the Archaean crust of eastern Finland.

Geochemical anomalies of hydrothermal plume at EPR 13 degrees N

During the DY105-12, 14cruise (RN DAYANG YIHAO, November 2003) on East Pacific Rise (EPR) 12-13 degrees N, the submarine hydrothermal activity was investigated and the CTD hydrocast was carried out at EPR12 degrees 39 ' N - 12 degrees 54 ' N. From the temperature anomalies and the concentrations of magnesium, chlorine, bromine in seawater samples, we discover that magnesium depletes 9.3%-22.4%, chlorine and bromine enrich 10.3%-28.7% and 10.7%-29.0% respectively relative to normal seawater at the stations which have chemistry anomalies, moreover temperature and chemistry anomalies are at the same layer. The depletion of magnesium in the plume may be caused by a fluid lacking of magnesium which rises after the hydrothermal fluid reaches the equilibrium with ambient seawater, the enrichment of chlorine and bromine might be the result of inputting later brine which is generated by phase separation due to hydrothermal activity. In addition, the Br/CI ratio in the abnormal layers at the survey area is identical to that in seawater, which implies that halite dissolution (or precipitation) occurs neither when the fluid is vented nor when hydrothermal fluid entraining ambient seawater rises to form plume. From the abnormal instance at E55 station, it is very possible that there might exist a new hydrothermal vent site.

Environmental impacts of the coal ash spill in Kingston, Tennessee: an 18-month survey.

An 18 month investigation of the environmental impacts of the Tennessee Valley Authority (TVA) coal ash spill in Kingston, Tennessee combined with leaching experiments on the spilled TVA coal ash have revealed that leachable coal ash contaminants (LCACs), particularly arsenic, selenium, boron, strontium, and barium, have different effects on the quality of impacted environments. While LCACs levels in the downstream river water are relatively low and below the EPA drinking water and ecological thresholds, elevated levels were found in surface water with restricted water exchange and in pore water extracted from the river sediments downstream from the spill. The high concentration of arsenic (up to 2000 μg/L) is associated with some degree of anoxic conditions and predominance of the reduced arsenic species (arsenite) in the pore waters. Laboratory leaching simulations show that the pH and ash/water ratio control the LCACs' abundance and geochemical composition of the impacted water. These results have important implications for the prediction of the fate and migration of LCACs in the environment, particularly for the storage of coal combustion residues (CCRs) in holding ponds and landfills, and any potential CCRs effluents leakage into lakes, rivers, and other aquatic systems.

Soil-Geochemical Factors controlling the Distribution and Oral Bioaccessibility of Nickel, Vanadium and Chromium in Northern Ireland Soils

Geogenic nickel (Ni), vanadium (V) and chromium (Cr) are present at elevated levels in soils in Northern Ireland. Whilst Ni, V and Cr total soil concentrations share common geological origins, their respective levels of oral bioaccessibility are influenced by different soil-geochemical factors. Oral bioaccessibility extractions were carried out on 145 soil samples overlying 9 different bedrock types to measure the bioaccessible portions of Ni, V and Cr. Principal component analysis identified two components (PC1 and PC2) accounting for 69% of variance across 13 variables from the Northern Ireland Tellus Survey geochemical data. PC1 was associated with underlying basalt bedrock, higher bioaccessible Cr concentrations and lower Ni bioaccessibility. PC2 was associated with regional variance in soil chemistry and hosted factors accounting for higher Ni and V bioaccessibility. Eight per cent of total V was solubilised by gastric extraction on average across the study area. High median proportions of bioaccessible Ni were observed in soils overlying sedimentary rock types. Whilst Cr bioaccessible fractions were low (max = 5.4%), the highest measured bioaccessible Cr concentration reached 10.0 mg kg-1, explained by factors linked to PC1 including high total Cr concentrations in soils overlying basalt bedrock.

What defines a geochemical map? Implications for environmental assessment.

The environmental quality of land is often assessed by the calculation of threshold values which aim to differentiate between concentrations of elements based on whether the soils are in residential or industrial sites. In Europe, for example, soil guideline values exist for agricultural and grazing land. A threshold is often set to differentiate between concentrations of the element that naturally occur in the soil and concentrations that result from diffuse anthropogenic sources. Regional geochemistry and, in particular, single component geochemical maps are increasingly being used to determine these baseline environmental assessments. The key question raised in this paper is whether the geochemical map can provide an accurate interpretation on its own. Implicit is the thought that single component geochemical maps represent absolute abundances. However,because of the compositional (closed) nature of the data univariate geochemical maps cannot be compared directly with one another.. As a result, any interpretation based on them is vulnerable to spurious correlation problems. What does this mean for soil geochemistry mapping, baseline quality documentation, soil resource assessment or risk evaluation? Despite the limitation of relative abundances, individual raw geochemical maps are deemed fundamental to several applications of geochemical maps including environmental assessments. However, element toxicity is related to its bioavailable concentration, which is lowered if its source is mixed with another source. Elements interact, for example under reducing conditions with iron oxides, its solid state is lost and arsenic becomes soluble and mobile. Both of these matters may be more adequately dealt with if a single component map is not interpreted in isolation to determine baseline and threshold assessments. A range of alternative compositionally compliant representations based on log-ratio and log-contrast approaches are explored to supplement the classical single component maps for environmental assessment. Case study examples are shown based on the Tellus soil geochemical dataset, covering Northern Ireland and the results of in vitro oral bioaccessibility testing carried out on a sub-set of archived Tellus Survey shallow soils following the Unified BARGE (Bioaccessibility Research Group of Europe).

Homogeneity of the geochemical reference material BRP-1 (paranábasin basalt) and assessment of minimum mass

Reference materials (RM) are required for quantitative analyses and their successful use is associated with the degree of homogeneity, and the traceability and confidence limits of the values established by characterisation. During the production of a RM, the chemical characterisation can only commence after it has been demonstrated that the material has the required level of homogeneity. Here we describe the preparation of BRP-1, a proposed geochemical reference material, and the results of the tests to evaluate its degree of homogeneity between and within bottles. BRP-1 is the first of two geochemical RM being produced by Brazilian institutions in collaboration with the United States Geological Survey (USGS) and the International Association of Geoanalysts (IAG). Two test portions of twenty bottles of BRP-1 were analysed by wavelength dispersive-XRF spectrometry and major, minor and eighteen trace elements were determined. The results show that for most of the investigated elements, the units of BRP-1 were homogeneous at conditions approximately three times more rigorous than those strived for by the test of sufficient homogeneity. Furthermore, the within bottle homogeneity of BRP-1 was evaluated using small beam (1 mm(2)) synchrotron radiation XRF spectrometry and, for comparison, the USGS reference materials BCR-2 and GSP-2 were also evaluated. From our data, it has been possible to assign representative minimum masses for some major constituents (1 mg) and for some trace elements (1-13 mg), except Zr in GSP-2, for which test portions of 74 mg are recommended.