Parameter optimization of AC rectangular wave outputs for aluminum cold wire GTAW

The objective of this work was to optimize the parameter setup for GTAW of aluminum using an AC rectangular wave output and continuous feeding. A series of welds was carried-out in an industrial joint, with variation of the negative and positive current amplitude, the negative and positive duration time, the travel speed and the feeding speed. Another series was carried out to investigate the isolate effect of the negative duration time and travel speed. Bead geometry aspects were assessed, such as reinforcement, penetration, incomplete fusion and joint wall bridging. The results showed that currents at both polarities are remarkably more significant than the respective duration times. It was also shown that there is a straight relationship between welding speed and feeding speed and this relationship must be followed for obtaining sound beads. A very short positive duration time is enough for arc stability achievement and when the negative duration time is longer than 5 ms its effect on geometry appears. The possibility of optimizing the parameter selection, despite the high inter-correlation amongst them, was demonstrate through a computer program. An approach to reduce the number of variables in this process is also presented.

Reciclagem de cavacos para a formação de carbonetos de titânio no metal de solda produzido por soldagem GTAW em aço-carbono

Pós-graduação em Engenharia Mecânica - FEIS

Caracterização de juntas soldadas em PAW e GTAW de chapas finas em aço maraging 300 submetidas a vários reparos

Pós-graduação em Engenharia Mecânica - FEG

Influência do aporte térmico da soldagem GTAW no balanço de fases Ferrita/Austenita do Aço Inoxidável Duplex UNS S32205

Pós-graduação em Engenharia Mecânica - FEIS

Modelización de procesos de soldadura (GMAW y GTAW) de la aleación de magnesio AZ31B. Estudio y análisis del comportamiento de este tipo de uniones soldadas frente a la corrosión en medios salinos

El magnesio y sus aleaciones representan un interesante campo de investigación dentro de la ingeniería de materiales debido a los retos que plantean tanto su conformabilidad como durabilidad. Las características físicas y mecánicas del magnesio y sus aleaciones los convierten en materiales de gran interés desde el punto de vista industrial al tratarse de uno de los materiales más abundantes y ligeros en un mundo en el que día a día los recursos y materias primas son más escasos por lo que el acceso a materiales abundantes y ligeros que permitan economizar el uso de energía cobrará mayor importancia en el futuro. En la coyuntura actual es por tanto necesario revisar procesos y procedimientos, investigando y tratando de ampliar desde este punto de vista si es posible mejorar los procedimientos de fabricación de los materiales disponibles actualmente o el desarrollo de nuevos, mejores que los anteriores, que permitan ayudar a la sostenibilidad del planeta. El magnesio, pese a ser un material muy abundante y relativamente barato, presenta una serie de inconvenientes que limitan de manera muy seria su aplicación industrial, su alta reactividad en presencia de oxígeno y su mal comportamiento frente a la corrosión así como limitaciones en su conformabilidad han estado limitando su uso y aplicaciones, los investigaciones dentro del campo de la metalurgia física de este material y el desarrollo de nuevas aleaciones han permitido su empleo en múltiples aplicaciones dentro de la industria aeroespacial, militar, automovilística, electrónica, deportiva y médica. La motivación para esta tesis doctoral ha sido tratar de aportar más luz sobre el comportamiento de una de las aleaciones comerciales base magnesio más empleadas, la AZ31B, tratando de modelizar como le afectan los procesos de soldadura y estudiando desde un punto de vista experimental como se ve modificada su microestructura, su comportamiento mecánico y su resistencia frente a la corrosión. Aunque en un principio se pensó en el empleo de métodos electroquímicos para el estudio de la corrosión de estos materiales, rápidamente se decidió prescindir de su uso dada la dificultad observada tanto durante los trabajos de investigación de esta Tesis como los encontrados por otros investigadores. Mediante microdurezas se han caracterizado mecánicamente las soldaduras de aleación de magnesio tipo AZ31 en función de diferentes materiales de aporte, observándose que el empleo de las aleaciones con mayor contenido de aluminio y zinc no contribuye a una mejora significativa de las propiedades mecánicas. Se han podido establecer correlaciones entre los modelos de simulación desarrollados y las microestructuras resultantes de los procesos reales de soldadura que permiten definir a priori que estructuras se van a obtener. De igual forma ha sido posible completar un estudio micrográfico y químico completo de las diferentes fases y microconstituyentes originados durante los procesos de soldadura, gracias a estos resultados se ha propuesto como hipótesis una explicación que justifica el comportamiento frente a la corrosión de estas aleaciones una vez soldadas. Los ensayos de corrosión realizados han permitido determinar correlaciones matemáticas que indican las velocidades de corrosión esperables de este tipo de aleaciones. Desde el punto de vista del diseño, los resultados obtenidos en este trabajo permitirán a otros investigadores y diseñadores tomar decisiones a la hora de decidir qué materiales de aporte emplear junto con las implicaciones que conllevan desde el punto de vista metalúrgico, mecánico o corrosivo las diferentes alternativas. Por último indicar que gracias al trabajo desarrollado se han definido modelos matemáticos para predecir el comportamiento frente a la corrosión de estas aleaciones, se han determinado las posibles causas y mecanismos por las que se gobierna la corrosión en la soldadura de chapas de aleación AZ31B y los motivos por los que se debe considerar el empleo de un material de aporte u otro. Los modelos de simulación desarrollados también han ayudado a comprender mejor la microestructura resultante de los procesos de soldadura y se han determinado que fases y microconstituyentes están presentes en las soldaduras de estas aleaciones. ABSTRACT Magnesium and its alloys represent and interesting research field in the material science due to the challenges of their fabrication and durability. The physical and mechanical properties of magnesium and its alloys make them a very interesting materials from and industrial point of view being one of the most abundant and lightest materials in a world in which day by day the lacking of resources and raw materials is more important, the use of light materials which allow to save energy will become more important in a near future. So that it is necessary to review processes and procedures, investigating and trying to improve current fabrication procedures and developing new ones, better than the former ones, in order to help with the sustainability of the planet. Although magnesium is a very common and relatively cheap material, it shows some inconveniences which limit in a major way their industrial application; its high reactivity in presence of oxygen, its poor corrosion resistance and some manufacturing problems had been limiting their use and applications, metallurgical investigations about this material and the development of new alloys have allowed its use in multiple applications in the aerospacial, military, automobile, electronics, sports and medical industry. The motivation for this thesis has been trying to clarify the behavior of one most used commercial base magnesium alloys, the AZ31, trying to modeling how its affected by thermal cycles of the welding process and studying from an experimental point of view how its microstructure is modified and how these modifications affect its mechanical behavior and corrosion resistance. Although at the beginning of this works it was though about the using of electrochemical techniques to evaluate the corrosion of these materials, rapidly it was decided not to use them because of the difficulty observed by during this research and by other investigators. The results obtained in this thesis have allowed to characterize mechanically AZ31 magnesium welding alloys considering different filler metals, according to this study using filler metals with a high content of aluminum and zinc does not represent an important improve It has been possible to establish correlations between simulation models and the resultant microstructures of the real melting processes originated during welding processes which allow to predict the structures which will be obtained after the welding. In addition to that it is possible to complete a complete micrographic and chemical analysis of the different phases and microconstituents created during welding, due to these results and hypothesis to explain the corrosion behavior of these welded alloys. Corrosion tests carried out have allowed defining mathematical correlations to predict corrosion rates of this kind of alloys. From a designing point of view, the results obtained in this work will let other investigators and designers to make decisions taking into account which implications have the different options from a metallurgical, mechanic and corrosive point of view. Finally we would like to indicate that thanks to this work it has been possible to define mathematical models to predict the corrosion behavior, the causes and the mechanism of this corrosion in the AZ31 welding sheets have been also determined and the reasons for using of one filler metal or another, the developed simulation models have also help to get a better understanding of the result microstructure determining the phases and the microconstituents present in the welding of this alloys.

ASTM A923-Practice A application to identify intermetallic phases in a UNS S32750 superduplex welded joint

Duplex and superduplex stainless steels present superior mechanical and corrosion properties when compared to usual stainless steels. This superiority is based on chemical composition when in a balanced microstructure (approximately 50% of ferrite). During welding, changes may occur in both, the chemical composition and volume fraction of phases in the material, which may generate the presence of intermetallic phases and, as a consequence, modify the mechanical and corrosion properties of this group of stainless steels. The objective of this work is to apply ASTM A923- Practice A to verify the presence of intermetallic phases in welded joints of UNS 32750 su-perduplex stainless steel. Tubes of UNS 32750, with external diameters of 18 and 44 mm and a thickness of 1.5 mm, were welded using orbital GTAW, with filler metal 25Cr-10Ni-4Mo and a diameter of 0.8 mm. The metal-based and welded joints were characterized by optical and scanning electron microscopy. The results showed that there was no precipitation of the intermetallic phase, such as sigma phase, detected by ASTM A923, but the HAZ of the two tubes studied presented small regions with chromium nitrides, which can also change the properties of welded joins.

Advanced orbital pipe welding

Since the introduction of automatic orbital welding in pipeline application in 1961, significant improvements have been obtained in orbital pipe welding systems. Requirement of more productive welding systems for pipeline application forces manufacturers to innovate new advanced systems and welding processes for orbital welding method. Various methods have been used to make welding process adaptive, such as visual sensing, passive visual sensing, real-time intelligent control, scan welding technique, multi laser vision sensor, thermal scanning, adaptive image processing, neural network model, machine vision, and optical sensing. Numerous studies are reviewed and discussed in this Master’s thesis and based on a wide range of experiments which already have been accomplished by different researches the vision sensor are reported to be the best choice for adaptive orbital pipe welding system. Also, in this study the most welding processes as well as the most pipe variations welded by orbital welding systems mainly for oil and gas pipeline applications are explained. The welding results show that Gas Metal Arc Welding (GMAW) and its variants like Surface Tension Transfer (STT) and modified short circuit are the most preferred processes in the welding of root pass and can be replaced to the Gas Tungsten Arc Welding (GTAW) in many applications. Furthermore, dual-tandem gas metal arc welding technique is currently considered the most efficient method in the welding of fill pass. Orbital GTAW process mostly is applied for applications ranging from single run welding of thin walled stainless tubes to multi run welding of thick walled pipes. Flux cored arc welding process is faster process with higher deposition rate and recently this process is getting more popular in pipe welding applications. Also, combination of gas metal arc welding and Nd:YAG laser has shown acceptable results in girth welding of land pipelines for oil and gas industry. This Master’s thesis can be implemented as a guideline in welding of pipes and tubes to achieve higher quality and efficiency. Also, this research can be used as a base material for future investigations to supplement present finding.

A quality and cost approach for welding process selection

The aim of this work was to propose, apply and evaluate a methodical approach to select welding processes in a productive environment based on market requirements of Quality and Costs. A case study was used. The welds were carried out in laboratory, simulating the joint conditions of a manufacturer and using several welding processes: SMAW, GTAW, pulsed GTAW, GMAW with CO2 and Ar based shielding gases and pulsed GMAW. For Quality analysis geometrical aspects of the beads were considered and for Cost analysis, welding parameters and consumable prices. Quantitative indices were proposed and evaluated. After that, evaluation of both Quality and Costs was done, showing to be possible to select the most suitable welding process to a specific application, taking into account the market conditions of a company.

Weld joint characteristics by nano-materials addition

The need for industries to remain competitive in the welding business, has created necessity to develop innovative processes that can exceed customer’s demand. Significant development in improving weld efficiency, during the past decades, still have their drawbacks, specifically in the weld strength properties. The recent innovative technologies have created smallest possible solid material known as nanomaterial and their introduction in welding production has improved the weld strength properties and to overcome unstable microstructures in the weld. This study utilizes a qualitative research method, to elaborate the methods of introducing nanomaterial to the weldments and the characteristic of the welds produced by different welding processes. The study mainly focuses on changes in the microstructural formation and strength properties on the welded joint and also discusses those factors influencing such improvements, due to the addition of nanomaterials. The effect of nanomaterial addition in welding process modifies the physics of joining region, thereby, resulting in significant improvement in the strength properties, with stable microstructure in the weld. The addition of nanomaterials in the welding processes are, through coating on base metal, addition in filler metal and utilizing nanostructured base metal. However, due to its insignificant size, the addition of nanomaterials directly to the weld, would poses complications. The factors having major influence on the joint integrity are dispersion of nanomaterials, characteristics of the nanomaterials, quantity of nanomaterials and selection of nanomaterials. The addition of nanomaterials does not affect the fundamental properties and characteristics of base metals and the filler metal. However, in some cases, the addition of nanomaterials lead to the deterioration of the joint properties by unstable microstructural formations. Still research are ongoing to achieve high joint integrity, in various materials through different welding processes and also on other factors that influence the joint strength.

Relacao entre o angulo da ponta do eletrodo e a geometria do cordao de solda no processo de soldagem tig

No processo de soldagem TIG (Tungstênio Inerte Gás), um dos fatores que influenciam o formato do cordão de solda é o ângulo da extremidade do eletrodo. Para estudar o comportamento do arco elétrico em função da geometria de ponta do eletrodo e suas conseqüências nos cordões de solda, efetuaram-se soldagens sobre corpos de prova sem deposição de material (bead-on-plate) através de parâmetros controlados e a mecanização do processo. Parâmetros tais como vazão do gás, velocidade de avanço da tocha e comprimento do arco foram testados para verificar a atuação em conjunto com o ângulo do eletrodo. Pela análise metalográfica (macrografia) estudaram-se os perfis dos cordões de solda, verificando-se que o ângulo exerce uma influência significativa na característica do arco tensão-corrente, na largura e profundidade de penetração da solda. Para maiores ângulos de extremidade do eletrodo obteve-se aumento na penetração, diminuição da tensão e largura do cordão de solda para uma mesma intensidade de corrente.

Repair Welding Effects on the Bending Fatigue Strength of AISI 4130 Aeronautical Steel used in a Critical to the Flight-Safety Structure

The aim of this study was to analyze the effect of successive TIG (tungsten inert gas) welding repairs on the reverse bending fatigue strength of AISI 4130 steel, which is widely used in components critical to the flight-safety. In order to simulate the abrupt maneuvers, wind bursts, motor vibration and helixes efforts, which generate cyclic bending loadings at the welded joints of a specific aircraft component called motor cradle, experimental reverse bending fatigue tests were carried out on specimens made from hot-rolled steel plate, 1.10 mm (0.043 in) thick, by mean of a SCHENK PWS equipment, with load ratio R = -1, under constant amplitude, at 30 Hz frequency and room temperature. It was observed that the bending fatigue strength decreases after the TIG (Tungsten Inert Gas) welding process application on AISI 4130 steel, with subsequent decrease due to re-welding sequence as well. Microstructural analyses and microhardness measurements on the base material, heat-affected zone (HAZ) and weld metal, as well as the effects of the weld bead geometry on the obtained results, have complemented this study.

Effects of several TIG weld repairs on the axial fatigue strength of AISI 4130 aeronautical steel-welded joints

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Fatigue strength of tungsten inert gas-repaired weld joints in airplane critical structures

In this work the effect of Gas Tungsten Arc Welding (GTAW) repairs on the axial fatigue strength of an AISI 4130 steel welded joint used in airframe critical to the flight-safety was investigated. Fatigue tests were performed at room temperature on 0.89 mm thick hot-rolled plates with constant amplitude and load ratio of R = 0.1, at 20 Hz frequency. Monotonic tensile tests, optical metallography and microhardness, residual stress and weld geometric factors measurements were also performed. The fatigue strength decreased with the number of GTAW repairs, and was related to microstructural and microhardness changes, as well as residual stress field and weld profile geometry factors, which gave origin to high stress concentration at the weld toe. (C) 2011 Elsevier B.V. All rights reserved.

Aplicação de cavacos de titânio para produção de revestimentos resistentes ao desgaste

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Avaliação de juntas soldadas em tubos de aço carbono submetidos a altas temperatura e pressões

The welding process in industrial piping is still the most effective way to ensure the durability and quality of the wide range of industrial process, although because of the high demand for energy and quality of the produced products, the piping has been constantly tested for high pressure applications and still high temperature. The welding method analyzed is the TIG (Tungsten Inert Gas) welding or GTAW (Gas-Shielded Tungsten Arc Welding), which ones have as principal feature the utilization of a not consumable tungsten electrode in the torch extremity , in this process is necessary a protective atmosphere of inert gas. The welding TIG advantage is the obtaining of a welded seam clean and with quality for not has slag after the welding. This work has as objective show the variability in the carbon steel piping welding parameters and by the tests in four proof bodies will be shown the influence of the variation of the welding methods in a welded seam. The tests will vary since the piece to be welded preparation, till penetrating liquid tests, welding macrography, welding x-ray and traction tests. Even been a clean and with quality welding is necessary a final inspection in the seam welded looking for defects almost inevitable resulted of the welded process, the obtained results have the objective of indicate and minimize the defects to ensure quality and durability of the welded seam