Ultra sensitive NO2 gas detection using the reduced graphene oxide coated etched fiber Bragg gratings

We report a simple and highly sensitive methodology for the room temperature NO2 gas sensing using reduced graphene oxide (RGO) coated clad etched fiber Bragg grating (eFBG). A significant shift (>10 pm) is observed in the reflected Bragg wavelength (lambda(B)) upon exposing RGO coated on the surface of eFBG to the NO2 gas molecules of concentration 0.5 ppm. The shift in Bragg wavelength is due to the change in the refractive index of RGO by charge transfer from the adsorbing NO2 molecules. The range of NO2 concentration is tested from 0.5 ppm to 3 ppm and the estimated time taken for 50% increase in Delta lambda(B) ranges from 20 min (for 0.5 ppm) to 6 min (for 3 ppm). (C) 2015 Elsevier B.V. All rights reserved.

Low-cost PCB-integrated polymer waveguide sensor for gas detection

An optical waveguide sensor formed directly on low-cost PCB substrates is presented for the first time. The device integrates polymer waveguides functionalized with chemical dyes, photonic and electronic components and allows multiple-gas detection. © 2011 OSA.

Low-cost PCB-integrated polymer waveguide sensor for gas detection

An optical waveguide sensor formed directly on low-cost PCB substrates is presented for the first time. The device integrates polymer waveguides functionalized with chemical dyes, photonic and electronic components and allows multiple-gas detection. © OSA/CLEO 2011.

Remote gas detection and quantitative analysis from infrared emission spectra obtained by Fourier transform infrared spectroscopy

Techniques for obtaining quantitative values of the temperatures and concentrations of remote hot gaseous effluents from their measured passive emission spectra have been examined in laboratory experiments. The high sensitivity of the spectrometer in the vicinity of the 2397 cm-1 band head region of CO2 has allowed the gas temperature to be calculated from the relative intensity of the observed rotational lines. The spatial distribution of the CO2 in a methane flame has been reconstructed tomographically using a matrix inversion technique. The spectrometer has been calibrated against a black body source at different temperatures and a self absorption correction has been applied to the data avoiding the need to measure the transmission directly. Reconstruction artifacts have been reduced by applying a smoothing routine to the inversion matrix.

Conversion of n-type CuTCNQ into p-type nitrogen-doped CuO and the implication for room temperature gas sensing

Sensors to detect toxic and harmful gases are usually based on metal oxides that are operated at elevated temperature. However, enabling gas detection at room temperature (RT) is a significant ongoing challenge. Here, we address this issue by demonstrating that microrods of semiconducting CuTCNQ (TCNQ=7,7,8,8-tetracyanoquinodimethane) with nanostructured features can be employed as conductometric gas sensors operating at 50°C for detection of oxidizing and reducing gases such as NO2 and NH3. The sensor is evaluated at RT and up to 200°C. It was found that CuTCNQ is transformed into a N-doped CuO material with p-type conductivity when annealed at the maximum temperature. This is the first time that such a transformation, from a semiconducting charge transfer material into a N-doped metal oxide is detected. It is shown here that both the surface chemistry and the type of majority charge carrier within the sensing layer is critically important for the type of response towards oxidizing and reducing gases. A detailed physical description of NO2 and NH3 sensing mechanism at CuTCNQ and N-doped CuO is provided to explain the difference in the response. For the N-doped CuO sensor, a detection limit of 1 ppm for NO2 and 10 ppm for NH3 are achieved.

Low power consumption and high sensitivity carbon monoxide gas sensor using indium oxide nanowire.

In this paper, micro gas sensor was fabricated using indium oxide nanowire for effective gas detection and monitoring system. Indium oxide nanowire was grown using thermal CVD, and their structural properties were examined by the SEM, XRD and TEM. The electric properties for microdropped indium oxide nanowire device were measured, and gas response characteristics were examined for CO gas. Sensors showed high sensitivity and stability for CO gas. And with below 20 mw power consumption, 5 ppm CO could be detected.

PCB-integrated optical gas sensor

A novel technological platform for multiple gas detection based on the use of PCB-integrated polymer waveguides is presented. A proof-of-principle ammonia sensor is reported integrating onto low-cost FR4 substrates all essential photonic, electronic and chemical components. The device's potential to detect multiple gases is demonstrated. © 2011 IEEE.

Design and characteristics of quantum cascade laser-based CO detection system

National High Technology Research and Development Program of China 2007AA03Z112；Program of Ministry of Education of China 20060183030；Program of Jilin Provincial Science and Technology Department of China 20070709；Program of Bureau of Science and Technology of Changchun City 2007107

Remote Detection and Identification of Organic Remains: An Assessment of Archaeological Potential

This paper reviews the various methods of using natural or induced light spectra as analytical tools in forensic archaeology. Chemical identi?cation can be made at long range and wide scale (tens of metres) down to short range and very small scale (nanometres). The identi?cation of organic gases and materials has used either chemical capture and chromatography, induced (laser or ultraviolet) light sources or laser Raman microscope spectroscopy. The remote gas detection method relies on the identi?cation of atmospheric gases by their characteristic light spectra. Modern spectroscopes can detect gases down to a few parts per million of an atmosphere. When the light source (wavelength) and direction is controlled, so laser-induced spectroscopy may be used to monitor the emission of gases such methane from buried organic remains. In order to identify the location of buried organic remains, a grid of sample points must be established using a base line or global
positioning system. When matched to base line or ground-positioning systems, such data can be manipulated by geographical information system packages. This would enable pinpointing of anomalies for excavation or avoidance. Microscope-based laser Raman spectroscopy can be used to directly analyse captured gases, swabs and surfaces without the problems of long-path detection. Copyright ? 2002 John Wiley & Sons, Ltd.

Evaluation of a simple disposable microband electrode device for amperometric gas sensing

We report a simple and facile methodology for constructing Pt (6.3 mm x 50 mu m) and Cu (6.3 mm x 30 mu m) annular microband electrodes for use in room temperature ionic liquids (RTILs) and propose their use for amperometric gas sensing. The suitability of microband electrodes for use in electrochemical analysis was examined in experiments on two systems. The first system studied to validate the electrochemical responses of the annular microband electrode was decamethylferrocene (DmFc), as a stable internal reference probe commonly used in ionic liquids, in [Pmim][NTf2], where the diffusion coefficients of DmFc and DmFc(+) and the standard electron rate constant for the DmFc/DmFc(+) couple were determined through fitting chronoamperometric and cyclic voltammetric responses with relevant simulations. These values are independently compared with those collected from a commercially available Pt microdisc electrode with excellent agreement. The second system focuses on O-2 reduction in [Pmim][NTf2], which is used as a model for gas sensing. The diffusion coefficients of O-2 and O-2(-) and the electron transfer rate constant were again obtained using chronoamperometry and cyclic voltammetry, along with simulations. Results determined from the microbands are again consistent to those evaluated from the Pt microdisc electrode when compared these results from home-made microband and commercially available microdisc electrodes. These observations indicate that the fabricated annular microband electrodes are suitable for quantitative measurements. Further the successful use of the Cu electrodes in the O-2 system suggests a cheap disposable sensor for gas detection. (C) 2013 Elsevier B.V. All rights reserved.

High-resolution seismic reflection investigation of gas accumulation and seepage in the tidal channels of the Ria of Aveiro barrier lagoon (Portugal)

O metano é um gás de estufa potente e uma importante fonte de energia. A importância global e impacto em zonas costeiras de acumulações e escape de gás metano são ainda pouco conhecidas. Esta tese investiga acumulações e escape de gás em canais de maré da Ria de Aveiro com dados de cinco campanhas de reflexão sísmica de alta resolução realizadas em 1986, 1999, 2002 e 2003. Estas incluem três campanhas de Chirp (RIAV99, RIAV02 e RIAV02A) e duas campanhas de Boomer (VOUGA86 e RIAV03). O processamento dos dados de navegação incluíram filtros de erros, correcções de sincronização de relógios de sistemas de aquisição de dados, ajuste de “layback” e estimativa da posição de “midpoint”. O processamento do sinal sísmico consistiu na correcção das amplitudes, remoção de ruído do tipo “burst”, correcções estáticas, correcção do “normal move-out”, filtragem passabanda, desconvolução da assinatura e migração Stolt F-K. A análise da regularidade do trajecto de navegação, dos desfasamentos entre horizontes e dos modelos de superfícies foi utilizada para controlo de qualidade, e permitiu a revisão e melhoria dos parâmetros de processamento. A heterogeneidade da cobertura sísmica, da qualidade do sinal, da penetração e da resolução, no seu conjunto constrangeram o uso dos dados a interpretações detalhadas, mas locais, de objectos geológicos da Ria. É apresentado um procedimento para determinar a escolha de escalas adequadas para modelar os objectos geológicos, baseado na resolução sísmica, erros de posicionamento conhecidos e desfasamentos médios entre horizontes. As evidências de acumulação e escape de gás na Ria de Aveiro incluem turbidez acústica, reflexões reforçadas, cortinas acústicas, domas, “pockmarks” e alinhamentos de “pockmarks” enterradas, horizontes perturbados e plumas acústicas na coluna de água (flares). A estratigrafia e a estrutura geológica controlam a distribuição e extensão das acumulações e escape de gás. Ainda assim, nestes sistemas de baixa profundidade de água, as variações da altura de maré têm um impacto significativo na detecção de gás com métodos acústicos, através de alterações nas amplitudes originais de reflexões reforçadas, turbidez acústica e branqueamento acústico em zonas com gás. Os padrões encontrados confirmam que o escape de bolhas de gás é desencadeado pela descida da maré. Há acumulações de gás em sedimentos Holocénicos e no substrato de argilas e calcários do Mesozóico. Evidências directas de escape de gás em sondagens em zonas vizinhas, mostraram gás essencialmente biogénico. A maioria do gás na área deve ter sido gerado em sedimentos lagunares Holocénicos. No entanto, a localização e geometria de estruturas de escape de fluidos em alguns canais de maré, seguem o padrão de fracturas do substrato Mesozóico, indicando uma possível fonte mais profunda de gás e que estas fracturas funcionam como condutas preferenciais de migração dos fluidos e exercem um controlo estrutural na ocorrência de gás na Ria.

Optical chemical sensors using polythiophene derivatives as active layer for detection of volatile organic compounds

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Gas sensor applications of zinc oxide thin film grown by the polymeric precursor method

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Controlled Synthesis of Layered Sn3O4 Nanobelts by Carbothermal Reduction Method and Their Gas Sensor Properties

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Optical chemical sensors using polythiophene derivatives as active layer for detection of volatile organic compounds

Several studies on polythiophene gas sensors, based mainly on electrochemical and gravimetric principles can be found in the literature. However, other principles of gas detection, such as optical and thermal, are still little studied. Optical sensing is suitable for remote detection and offers great versatility at low cost. Here,we report on the use of thin films of seven polythiophene derivatives as active layer in optical sensors for the detection of six volatile organic compounds (n-hexane, toluene, tetrahydrofuran, chloroform, dichloromethane and methanol) and water vapor, in concentration range of 500-30,000 ppm. The results showed that it is possible to use different polythiophene derivatives to differentiate VOCs by optical sensing. Differentiation can be performed based on the presence or not of response to an analyte and the sensitivity value of the sensors for the analytes. Another important feature is the lack of the effect of humidity on the response of most films, which could be a major drawback in the application of these sensors. (C) 2011 Elsevier B.V. All rights reserved.