Modelling and visualisation of material flow in friction stir spot welding

Abstract The material flow in friction stir spot welding of aluminium to both aluminium and steel has been investigated, using pinless tools in a lap joint geometry. The flow behaviour was revealed experimentally using dissimilar Al alloys of similar strength. The effect on the material flow of tool surface features, welding conditions (rotation speed, plunge depth, dwell time), and the surface state of the steel sheet (un-coated or galvanized) have been systematically studied. A novel kinematic flow model is presented, which successfully predicts the observed layering of the dissimilar Al alloys under a range of conditions. The model and the experimental observations provide a consistent interpretation of the stick-slip conditions at the tool-workpiece interface, addressing an elusive and long-standing issue in the modelling of heat generation in friction stir processing.

Failure modes and fatigue behavior of conventional and refilled friction stir spot welds in AA 6061-T6 sheets

The fatigue behavior of conventional friction stir spot welding (FSSW) and friction stir spot welding refilled by the friction forming process (FSSW-FFP) in aluminum 6061-T6 lap shear specimens, are investigated based on the experimental observations. Optical micrographs of the welds after fatigue failure in both the cases are examined to study the fatigue crack propagation and failure modes. Experimental results indicate that the fatigue strength of the FSSW-FFP weld samples is higher than that of the conventional FSSW samples at all loads. Fracture surfaces are analyzed in detail using the scanning electron microscope. (C) 2013 Elsevier Ltd. All rights reserved.

Static shear strength and fatigue life of refill friction stir spot welded AA 6061-T6 sheets

This study was aimed at evaluating the static shear strength and fatigue properties of the newly developed refilled friction stir spot welded AA 6061-T6 joints. The keyhole, the process disadvantage of conventional friction stir spot welding, was refilled successfully, using an additional filler plate, with specially designed tools. Two different tool profiles, namely, convex and concave, were used for the refilling process. Sound and defect free joints were obtained by the refilling process. Joints refilled with convex tools showed better static shear strength than those with the concave ones. The variation of microhardness in different regions of the weld was analysed. Fatigue tests were conducted on the lap shear specimens at a stress ratio of R=0.1. The optical micrographs of the welds after fatigue failure in both the conventional and refilled processes were examined to study the fatigue crack propagation and failure modes.

Effect of tool speeds during friction stir lap welding on mode of fracture and fracture strength of Al 6060-T5 joints

Friction stir lap welding (FSLW) of an age hardened Al alloy and evaluations of how FS speeds affected hooking and how hooking and softening due to FS affected fracture strength of the lap welds have been conducted. It was found that increasing rotation speed and reducing welding speed (v) increased the stir zone size (AB-SZ) and also hook size (h), although a maximum value of h (hMax) reached. The features of hooks for the observed - AB-SZ-h relationships are presented and explained. It was found that when h increased to a value of ~ 0.9 mm (for the 3 mm alloy sheets), it started to invoke a significant effect on reducing fracture strength. Factors such as FS softening and insufficient joining, limited the fracture strength of the lap welds for small h values and these are presented and discussed.

Mechanical properties of Al and Mg alloy welds made by friction stir lap welding

The unfavourable effect of hooking or softening, respectively, on fracture strength of joints made using friction stir lap welding (FSLW) is known but the combined effect on the magnitude of strength reduction is not clear. In this study, FSLW experiments using AA6060-T5 and AZ31B-H24 alloys were conducted. For both alloys, rotation speed has a dominant effect on increasing the hook size due to increasing the stir flow volume thus lifting more the original lapping surfaces. In AA6060 welds, FS softening has limited the strength, when hook size approaches zero. Meanwhile hook starts to reduce the strength significantly, when its size reaches a critical value. The maximum strength of AA6060 FSL welds reaches ~ 70% of the base metal UTS when hook size approaches zero. This is in contract to ~30% for AZ31B FSL welds. This can be explained by the local plastic deformation behaviour during lap tensile testing.

Fracture strengths of Mg alloy AZ31B-H24 friction stir lap welds

The effects of selected friction stir lap welding parameters on fracture strength of Mg alloy AZ31B-H24 welds have been studied. Rotation speed has been found to affect significantly the flow related hook size formation. Furthermore, fracture strength decreased almost linearly with hook size. A small amount of softening was detected in fracture location that was outside the nugget zone and thus this softening may only adversely affect the fracture strength slightly. Finally, simulation results are presented to show the uneven stress distribution in a lap geometry which together with the relative brittleness of the stir material must be the cause to have significantly reduced the fracture strength.

Effects of tool positioning on joint interface microstructure and fracture strength of friction stir lap Al-to-steel welds

Friction stir lap welding (FSLW) experiments have been conducted to study the effects of tool positioning on microstructures formed in the Al-to-steel interface region and on joint strength, defined as maximum applied force over the width (F m/w s) of the test sample, of the welds. Various pin positioning and speed conditions were used in the FSLW experiments followed by microstructure examination on the interface regions and tensile-shear testing on the welds, including an examination on crack propagation in mixed stir zone. It was found that when the pin was close to the bottom steel piece, Al-to-steel reaction occurred resulting in intermetallic outbursts formed along the interface. This represents the case of incomplete metallurgical joint. When the pin was lowered to just reach the steel, a thin and continued interface intermetallic layer formed. Evidences and consideration on growth kinetics have suggested that the layer could only remain thin (≤2.5 μm) during FSLW. This layer could bear a high load during tensile-shear testing and the adjacent aluminium deformed and fractured instead. The resulting F m/w s was high. When the pin penetrated to steel, F m/w s reduced due to brittle fracture being dominant inside mixed stir zone. Evidences have shown that the amount of penetration and speed condition during FSLW do not have large effects on F m/w s.

An Investigation of Friction During Friction Stir Welding of Metallic Materials

The technique of friction stir welding (FSW) puts effective use frictional heat for the purpose of joining metallic materials. In this research article, we present and discuss an experimental method to determine the coefficient of friction during FSW. The experiments were conducted to study the interaction between the FSW tool (a die steel) and the base metal (a high strength aluminum alloy) at various contact pressures (13MPa, 26MPa, and 39MPa) and rotation speeds (200rpm, 600rpm, 1000rpm, and 1400rpm). The experimental results, the microstructure, and the process temperature reveal the experimental setup to be capable of simulating the conditions during FSW. The coefficient of friction was found to vary from 0.15 to 1.4, and the temperature increased to as high as 450C. The coefficient of friction was found to increase with temperature. There exists a critical temperature at which point a steep increase in the coefficient of friction was observed. The critical temperature decreases from 250C at a contact pressure of 26MPa to 200C at contact pressure of 34MPa. Below the critical temperature at a specific contact pressure the maximum coefficient of friction is 0.6, and above the critical temperature it reaches a value as high as 1.4. The steep increase in the coefficient of friction is found to be due to the seizure phenomenon and the contact condition during FSW between the tool and the workpiece (base metal) is found to be sticking.

Optimization of friction stir welding parameters for dissimilar aluminum alloys

Assembly consisting of cast and wrought aluminum alloys has wide spread application in defense and aero space industries. For the efficacious use of the transition joints, the weld should have adequate strength and formability. In the present investigation, A356 and 6061 aluminum alloys were friction stir welded under tool rotational speed of 1000-1400 rpm and traversing speed of 80-240 mm/min, keeping other parameters same. The variable process window is responsible for the change in total heat input and cooling rate during welding. Structural characterization of the bonded assemblies exhibits recovery-recrystallization in the stirring zone and breaking of coarse eutectic network of Al-Si. Dispersion of fine Si rich particles, refinement of 6061 grain size, low residual stress level and high defect density within weld nugget contribute towards the improvement in bond strength. Lower will be the tool rotational and traversing speed, more dominant will be the above phenomena. Therefore, the joint fabricated using lowest tool traversing and rotational speed, exhibits substantial improvement in bond strength (similar to 98% of that of 6061 alloy), which is also maximum with respect to others. (C) 2010 Elsevier Ltd. All rights reserved.

Positional dependence of material flow in friction stir welding: analysis of joint line remnant and its relevance to dissimilar metal welding

Understanding material flow in friction stir welding is important for production of sound dissimilar metal welding that control the intermixing of two alloys being welded and consequent formation of new constituents which influences the weld properties. In the present experimental investigation material flow patterns are visualised using dissimilar and similar aluminium alloys using a simple innovative ,experiment. The experimental results reveal that only a portion of material transported from the leading edge undergoes chaotic flow and the remaining is deposited systematically in the trailing edge of the weld. Using this information it is shown that the formation of a friction stir welding defect, joint line remnant, does not occur only when the weld interface is on the advancing side. The material flow visualisation study has been utilised to analyse the mechanism of weld formation and its usefulness in improving fatigue properties and for dissimilar metal welds.