Age-Dependent Fragility and Life-Cycle Cost Analysis of Timber and Steel Distribution Poles Subjected to Hurricanes

Power distribution systems are susceptible to extreme damage from natural hazards especially hurricanes. Hurricane winds can knock down distribution poles thereby causing damage to the system and power outages which can result in millions of dollars in lost revenue and restoration costs. Timber has been the dominant material used to support overhead lines in distribution systems. Recently however, utility companies have been searching for a cost-effective alternative to timber poles due to environmental concerns, durability, high cost of maintenance and need for improved aesthetics. Steel has emerged as a viable alternative to timber due to its advantages such as relatively lower maintenance cost, light weight, consistent performance, and invulnerability to wood-pecker attacks. Both timber and steel poles are prone to deterioration over time due to decay in the timber and corrosion of the steel. This research proposes a framework for conducting fragility analysis of timber and steel poles subjected to hurricane winds considering deterioration of the poles over time. Monte Carlo simulation was used to develop the fragility curves considering uncertainties in strength, geometry and wind loads. A framework for life-cycle cost analysis is also proposed to compare the steel and timber poles. The results show that steel poles can have superior reliability and lower life-cycle cost compared to timber poles, which makes them suitable substitutes.

Seismic vulnerability: From building evaluation to a typology generalization

Outlining the best strategies for seismic risk mitigation requires that both benefits and costs of retrofitting are known in advance. The assessment of the vulnerability of building typologies is a first step of a more extensive effort, concerning the analysis of the viability of seismic risk mitigation and taking into account retrofitting costs. The methodology adopted to obtain the seismic vulnerability of some classes of residential buildings existing in mainland Portugal is presented. This methodology is based on a structural analysis of individual buildings belonging to the same typology. An application example is presented to illustrate the methodology. Fragility curves of “boxed” building typology are also presented and broken down into three height classes: low rise, medium-rise and high-rise. These curves are based on average capacity spectra derived from several individual buildings belonging to the same typology.

A probabilistic approach to classify the levee reliability

This work aims to evaluate the reliability of these levee systems, calculating the probability of “failure” of determined levee stretches under different loads, using probabilistic methods that take into account the fragility curves obtained through the Monte Carlo Method. For this study overtopping and piping are considered as failure mechanisms (since these are the most frequent) and the major levee system of the Po River with a primary focus on the section between Piacenza and Cremona, in the lower-middle area of the Padana Plain, is analysed. The novelty of this approach is to check the reliability of individual embankment stretches, not just a single section, while taking into account the variability of the levee system geometry from one stretch to another. This work takes also into consideration, for each levee stretch analysed, a probability distribution of the load variables involved in the definition of the fragility curves, where it is influenced by the differences in the topography and morphology of the riverbed along the sectional depth analysed as it pertains to the levee system in its entirety. A type of classification is proposed, for both failure mechanisms, to give an indication of the reliability of the levee system based of the information obtained by the fragility curve analysis. To accomplish this work, an hydraulic model has been developed where a 500-year flood is modelled to determinate the residual hazard value of failure for each stretch of levee near the corresponding water depth, then comparing the results with the obtained classifications. This work has the additional the aim of acting as an interface between the world of Applied Geology and Environmental Hydraulic Engineering where a strong collaboration is needed between the two professions to resolve and improve the estimation of hydraulic risk.

Estimación del riesgo sísmico en puerto príncipe (Haití)

Tras el devastador terremoto del 12 de enero de 2010 en Puerto Príncipe, Haití, las autoridades locales, numerosas ONGs y organismos nacionales e internacionales están trabajando en el desarrollo de estrategias para minimizar el elevado riesgo sísmico existente en el país. Para ello es necesario, en primer lugar, estimar dicho riesgo asociado a eventuales terremotos futuros que puedan producirse, evaluando el grado de pérdidas que podrían generar, para dimensionar la catástrofe y actuar en consecuencia, tanto en lo referente a medidas preventivas como a adopción de planes de emergencia. En ese sentido, este Trabajo Fin de Master aporta un análisis detallado del riesgo sísmico asociado a un futuro terremoto que podría producirse con probabilidad razonable, causando importantes daños en Puerto Príncipe. Se propone para ello una metodología de cálculo del riesgo adaptada a los condicionantes de la zona, con modelos calibrados empleando datos del sismo de 2010. Se ha desarrollado en el marco del proyecto de cooperación Sismo-Haití, financiado por la Universidad Politécnica de Madrid, que comenzó diez meses después del terremoto de 2010 como respuesta a una petición de ayuda del gobierno haitiano. El cálculo del riesgo requiere la consideración de dos inputs: la amenaza sísmica o movimiento esperado por el escenario definido (sismo de cierta magnitud y localización) y los elementos expuestos a esta amenaza (una clasificación del parque inmobiliario en diferentes tipologías constructivas, así como su vulnerabilidad). La vulnerabilidad de estas tipologías se describe por medio de funciones de daño: espectros de capacidad, que representan su comportamiento ante las fuerzas horizontales motivadas por los sismos, y curvas de fragilidad, que representan la probabilidad de que las estructuras sufran daños al alcanzar el máximo desplazamiento horizontal entre plantas debido a la mencionada fuerza horizontal. La metodología que se propone especifica determinadas pautas y criterios para estimar el movimiento, asignar la vulnerabilidad y evaluar el daño, cubriendo los tres estados del proceso. Por una parte, se consideran diferentes modelos de movimiento fuerte incluyendo el efecto local, y se identifican los que mejor ajustan a las observaciones de 2010. Por otra se clasifica el parque inmobiliario en diferentes tipologías constructivas, en base a la información extraída en una campaña de campo y utilizando además una base de datos aportada por el Ministerio de Obras Públicas de Haití. Ésta contiene información relevante de todos los edificios de la ciudad, resultando un total de 6 tipologías. Finalmente, para la estimación del daño se aplica el método capacidad-demanda implementado en el programa SELENA (Molina et al., 2010). En primer lugar, utilizado los datos de daño del terremoto de 2010, se ha calibrado el modelo propuesto de cálculo de riesgo sísmico: cuatro modelos de movimiento fuerte, tres modelos de tipo de suelo y un conjunto de funciones de daño. Finalmente, con el modelo calibrado, se ha simulado un escenario sísmico determinista correspondiente a un posible terremoto con epicentro próximo a Puerto Príncipe. Los resultados muestran que los daños estructurales serán considerables y podrán llevar a pérdidas económicas y humanas que causen un gran impacto en el país, lo que pone de manifiesto la alta vulnerabilidad estructural existente. Este resultado será facilitado a las autoridades locales, constituyendo una base sólida para toma de decisiones y adopción de políticas de prevención y mitigación del riesgo. Se recomienda dirigir esfuerzos hacia la reducción de la vulnerabilidad estructural - mediante refuerzo de edificios vulnerables y adopción de una normativa sismorresistente- y hacia el desarrollo de planes de emergencia. Abstract After the devastating 12 January 2010 earthquake that hit the city of Port-au-Prince, Haiti, strategies to minimize the high seismic risk are being developed by local authorities, NGOs, and national and international institutions. Two important tasks to reach this objective are, on the one hand, the evaluation of the seismic risk associated to possible future earthquakes in order to know the dimensions of the catastrophe; on the other hand, the design of preventive measures and emergency plans to minimize the consequences of such events. In this sense, this Master Thesis provides a detailed estimation of the damage that a possible future earthquake will cause in Port-au-Prince. A methodology to calculate the seismic risk is proposed, adapted to the study area conditions. This methodology has been calibrated using data from the 2010 earthquake. It has been conducted in the frame of the Sismo-Haiti cooperative project, supported by the Technical University of Madrid, which started ten months after the 2010 earthquake as an answer to an aid call of the Haitian government. The seismic risk calculation requires two inputs: the seismic hazard (expected ground motion due to a scenario earthquake given by magnitude and location) and the elements exposed to the hazard (classification of the building stock into building typologies, as well as their vulnerability). This vulnerability is described through the damage functions: capacity curves, which represent the structure performance against the horizontal forces caused by the seisms; and fragility curves, which represent the probability of damage as the structure reaches the maximum spectral displacement due to the horizontal force. The proposed methodology specifies certain guidelines and criteria to estimate the ground motion, assign the vulnerability, and evaluate the damage, covering the whole process. Firstly, different ground motion prediction equations including the local effect are considered, and the ones that have the best correlation with the observations of the 2010 earthquake, are identified. Secondly, the classification of building typologies is made by using the information collected during a field campaign, as well as a data base provided by the Ministry of Public Works of Haiti. This data base contains relevant information about all the buildings in the city, leading to a total of 6 different typologies. Finally, the damage is estimated using the capacity-spectrum method as implemented in the software SELENA (Molina et al., 2010). Data about the damage caused by the 2010 earthquake have been used to calibrate the proposed calculation model: different choices of ground motion relationships, soil models, and damage functions. Then, with the calibrated model, a deterministic scenario corresponding to an epicenter close to Port-au-Prince has been simulated. The results show high structural damage, and therefore, they point out the high structural vulnerability in the city. Besides, the economic and human losses associated to the damage would cause a great impact in the country. This result will be provided to the Haitian Government, constituting a scientific base for decision making and for the adoption of measures to prevent and mitigate the seismic risk. It is highly recommended to drive efforts towards the quality control of the new buildings -through reinforcement and construction according to a seismic code- and the development of emergency planning.

Moldels for reproducing the damage scenario of the Lorca earthquake

A damage scenario modelling is developed and compared with the damage distribution observed after the 2011 Lorca earthquake. The strong ground motion models considered include five modern ground motion prediction equations (GMPEs) amply used worldwide. Capacity and fragility curves from the Risk-UE project are utilized to model building vulnerability and expected damage. Damage estimates resulting from different combinations of GMPE and capacity/fragility curves are compared with the actual damage scenario, establishing the combination that best explains the observed damage distribution. In addition, some recommendations are proposed, including correction factors in fragility curves in order to reproduce in a better way the observed damage in masonry and reinforce concrete buildings. The lessons learned would contribute to improve the simulation of expected damages due to future earthquakes in Lorca or other regions in Spain with similar characteristics regarding attenuation and vulnerability.

Design Expressions and Dynamic Evaluation of CFST Bridges Subjected to Seismic Hazards

Thesis (Ph.D.)--University of Washington, 2016-06

Evaluation of seismic losses of RC buildings: the case of the industrial areas after the 2012 Emilia Earthquake

The topic of seismic loss assessment not only incorporates many aspects of the earthquake engineering, but also entails social factors, public policies and business interests. Because of its multidisciplinary character, this process may be complex to challenge, and sound discouraging to neophytes. In this context, there is an increasing need of deriving simplified methodologies to streamline the process and provide tools for decision-makers and practitioners. This dissertation investigates different possible applications both in the area of modelling of seismic losses, both in the analysis of observational seismic data. Regarding the first topic, the PRESSAFE-disp method is proposed for the fast evaluation of the fragility curves of precast reinforced-concrete (RC) structures. Hence, a direct application of the method to the productive area of San Felice is studied to assess the number of collapses under a specific seismic scenario. In particular, with reference to the 2012 events, two large-scale stochastic models are outlined. The outcomes of the framework are promising, in good agreement with the observed damage scenario. Furthermore, a simplified displacement-based methodology is outlined to estimate different loss performance metrics for the decision-making phase of the seismic retrofit of a single RC building. The aim is to evaluate the seismic performance of different retrofit options, for a comparative analysis of their effectiveness and the convenience. Finally, a contribution to the analysis of the observational data is presented in the last part of the dissertation. A specific database of losses of precast RC buildings damaged by the 2012 Earthquake is created. A statistical analysis is performed, allowing deriving several consequence functions. The outcomes presented may be implemented in probabilistic seismic risk assessments to forecast the losses at the large scale. Furthermore, these may be adopted to establish retrofit policies to prevent and reduce the consequences of future earthquakes in industrial areas.

Seismic vulnerability of buildings and non-structural elements: insights from the 2011 Lorca earthquake

This PhD dissertation presents a profound study of the vulnerability of buildings and non-structural elements stemming from the investigation of the Mw 5.2 Lorca 2011 earthquake; which constitutes one of the most significant earthquakes in Spain. It left nine fatalities due to falling debris from reinforced concrete buildings, 394 injured and material damage valued at 800 million euros. Within this framework, the most relevant initiatives concerning the vulnerability of buildings and the exposure of Lorca are studied. This work revealed two lines of research: the elaboration of a rational method to determine the adequacy of a specific fragility curve for the particular seismic risk study of a region; and the relevance of researching the seismic performance of non-structural elements. As a consequence, firstly, a method to assess and select fragility curves for seismic risk studies from the catalogue of those available in the literature is elaborated and calibrated by means of a case study. The said methodology is based on a multidimensional index and provides a ranking that classifies the curves in terms of adequacy. Its results for the case of Lorca led to the elaboration of new fragility curves for unreinforced masonry buildings. Moreover, a simplified method to account for the unpredictable directionality of the seism in the creation of fragility curves is contributed. Secondly, the characterisation of the seismic capacity and demand of the non-structural elements that caused most of the human losses is studied. Concerning the capacity, an analytical approach derived from theoretical considerations to characterise the complete out-of-plane seismic response curve of unreinforced masonry cantilever walls is provided; as well as a simplified and more practical trilinear version of it. Concerning the demand, several methods for characterising the Floor Response Spectra of reinforced concrete buildings are tested through case studies.

Growth Curves For Girls With Turner Syndrome.

The objective of this study was to review the growth curves for Turner syndrome, evaluate the methodological and statistical quality, and suggest potential growth curves for clinical practice guidelines. The search was carried out in the databases Medline and Embase. Of 1006 references identified, 15 were included. Studies constructed curves for weight, height, weight/height, body mass index, head circumference, height velocity, leg length, and sitting height. The sample ranged between 47 and 1,565 (total = 6,273) girls aged 0 to 24 y, born between 1950 and 2006. The number of measures ranged from 580 to 9,011 (total = 28,915). Most studies showed strengths such as sample size, exclusion of the use of growth hormone and androgen, and analysis of confounding variables. However, the growth curves were restricted to height, lack of information about selection bias, limited distributional properties, and smoothing aspects. In conclusion, we observe the need to construct an international growth reference for girls with Turner syndrome, in order to provide support for clinical practice guidelines.

Low-frequency Raman spectra and fragility of imidazolium ionic liquids

Raman spectra within the 5-200 cm(-1) range have been recorded as a function of temperature for different ionic liquids based on imidazolium cations. A correlation has been found between fragility and the temperature dependence of the strength of fast relaxational motions. Understanding quasielastic scattering as the relaxational contribution to ionic mean-squared displacement elucidates some effects on ionic liquids' fragility resulting from modifications in the chemical structure. (C) 2010 American Institute of Physics. [doi:10.1063/1.3462962]

Fragility and glassy dynamics of 2Ca(NO(3))(2)center dot 3KNO(3) under pressure: Molecular dynamics simulations

Molecular dynamics simulations of the glass-forming liquid 2Ca(NO(3))(2)center dot 3KNO(3) (CKN) were performed from high temperature liquid states down to low temperature glassy states at six different pressures from 10(-4) to 5.0 GPa. The temperature dependence of the structural relaxation time indicates that the fragility of liquid CKN changes with pressure. In line with recent proposal [Scopigno , Science 302, 849 (2003)], the change on liquid fragility is followed by a proportional change of the nonergodicity factor of the corresponding glass at low temperature. (c) 2008 American Institute of Physics.

STRESS-STRAIN CURVES FOR STEEL FIBER-REINFORCED CONCRETE IN COMPRESSION

This paper presents a study on the compressive behavior of steel fiber-reinforced concrete. In this study, an analytical model for stress-strain curve for steel fiber-reinforced concrete is derived for concretes with strengths of 40 MPa and 60 MPa at the age of 28 days. Those concretes were reinforced with steel fibers with hooked ends 35 mm long and with aspect ratio of 65. The analytical model was compared with some experimental stress-strain curves and with some models reported in technical literature. Also, the accuracy of the proposed stress-strain curve was evaluated by comparison of the area under stress-strain curve. The results showed good agreement between analytical and experimental data and the benefits of the using of fibers in the compressive behavior of concrete.

Ion nitriding of a superaustenitic stainless steel: Wear and corrosion characterization

The superiority of superaustenitic stainless steel (SASS) lies in its good weldability and great resistance to stress corrosion and pitting, because of its higher chromium, molybdenum, and nitrogen contents, when compared to general stainless steels. However, some of its applications are limited by very poor wear behavior. Plasma-nitriding is a very effective treatment for producing wear resistant and hard surface layers on stainless steels without compromising the corrosion resistance. In this work, UNS S31254 SASS samples were plasma-nitrided at three different temperatures (400, 450, and 500 degrees C), under a pressure of 500 Pa, for 5 h, in order to verify the influence of the temperature on the morphology, wear, and corrosion behavior of the modified surface layers. The plasma-nitrided samples were analyzed by means of optical microscopy, micro-hardness. X-ray diffraction, wear, and corrosion tests. Wear tests were conducted in a fixed ball micro-wear machine and corrosion behavior was carried out in natural sea water by means of potentiodynamic polarization curves. For the sample which was plasma-nitrided at 400 degrees C, only the expanded austenite phase was observed, and for the treatments performed at 450 and 500 degrees C, chromium nitrides (CrN and Cr(2)N) were formed in addition to the expanded austenite. Wear volume and Knoop surface hardness increased as the plasma-nitriding temperature increased. Higher wear rates were observed at high temperatures, probably due to the increment on layer fragility. The sample modified at 400 degrees C exhibited the best corrosion behavior among all the plasma-nitriding conditions. (C) 2010 Elsevier B.V. All rights reserved.

A family of implementation-friendly BN elliptic curves

For the last decade, elliptic curve cryptography has gained increasing interest in industry and in the academic community. This is especially due to the high level of security it provides with relatively small keys and to its ability to create very efficient and multifunctional cryptographic schemes by means of bilinear pairings. Pairings require pairing-friendly elliptic curves and among the possible choices, Barreto-Naehrig (BN) curves arguably constitute one of the most versatile families. In this paper, we further expand the potential of the BN curve family. We describe BN curves that are not only computationally very simple to generate, but also specially suitable for efficient implementation on a very broad range of scenarios. We also present implementation results of the optimal ate pairing using such a curve defined over a 254-bit prime field. (C) 2001 Elsevier Inc. All rights reserved.