Narrow Gap flux-cored arc welding of high strength shipbuilding steels

This thesis is part of the Arctic Materials Technologies Development –project. The research of the thesis was done in cooperation with Arctech Helsinki Shipyard, Lappeenranta University of Technology and Kemppi Oy. Focus of the thesis was to study narrow gap flux-cored arc welding of two high strength steels with three different groove angles of 20°, 10° and 5°. Welding of the 25 mm thick E500 TMCP and 10 mm thick EH36 steels was mechanized and Kemppi WisePenetration and WiseFusion processes were tested with E500 TMCP steel. EH36 steel test pieces were welded without Wise processes. Shielding gases chosen were carbon dioxide and a mixture of argon and carbon dioxide. Welds were tested with non-destructive and destructive testing methods. Radiographic, visual, magnetic particle and liquid penetrant testing proved that welds were free from imperfections. After non-destructive testing, welds were tested with various destructive testing methods. Impact strength, bending, tensile strength and hardess tests proved that mechanized welding and Wise processes produced quality welds with narrower gap. More inconsistent results were achieved with test pieces welded without Wise processes. Impact test results of E500 TMCP exceeded the 50 J limit on weld, set by Russian Maritime Register of Shipping. EH36 impact test results were much closer to the limiting values of 34 J on weld and 47 on HAZ. Hardness values of all test specimens were below the limiting values. Bend testing and tensile testing results fulfilled the the Register requirements. No cracking or failing occurred on bend test specimens and tensile test results exceeded the Register limits of 610 MPa for E500 TMCP and 490 MPa for EH36.

Welding current effect on diffusible hydrogen content in flux cored arc weld metal

The application of flux cored arc welding (FCAW) has increased in manufacturing and fabrication. Even though FCAW is well known for its good capability in producing quality welds, few reports have been published on the cause of the relatively high diffusible hydrogen content in the weld metal and its relation with the ingredients used in the wire production and with the welding parameters (mainly welding current). This paper describes experiments where data obtained from weld metal diffusible hydrogen analysis, metal droplet collection, and high-speed recording of metal droplet transfer were used to evaluate the effect of welding current on diffusible hydrogen content in the weld metal. The results from gas chromatography analysis showed that weld metal hydrogen content indeed increased with welding current. A polynomial regressional analysis concluded that hydrogen increase with current was better described by a linear function with proportional constant of approximately 0.7 or 70%. Different from the GMA welding transfer behavior, statistical analysis showed only a small increase in metal droplet size with increasing current. The metal transfer mode remained in the globular range for currents between 100 and 150 A. The most surprising findings were with the high-speed cinematography recording. Observing the high speed movies, it was possible to see that at low current, "unmelted" flux sporadically touched the weld pool but at higher current, the flux remained touching the weld pool during the whole time of droplet formation and transfer. It is believed that since the flux has ingredients that contain hydrogen, hydrogen passes through the arc undisturbed, going to the weld bead intact and increasing the hydrogen content in the weld metal. Another important observation is regarding to droplet size. Droplet size increased with increasing current because forces from decomposed gases from the flux could sustain the droplets, retarding their transfer and allowing them to grow.

Advanced orbital pipe welding

Since the introduction of automatic orbital welding in pipeline application in 1961, significant improvements have been obtained in orbital pipe welding systems. Requirement of more productive welding systems for pipeline application forces manufacturers to innovate new advanced systems and welding processes for orbital welding method. Various methods have been used to make welding process adaptive, such as visual sensing, passive visual sensing, real-time intelligent control, scan welding technique, multi laser vision sensor, thermal scanning, adaptive image processing, neural network model, machine vision, and optical sensing. Numerous studies are reviewed and discussed in this Master’s thesis and based on a wide range of experiments which already have been accomplished by different researches the vision sensor are reported to be the best choice for adaptive orbital pipe welding system. Also, in this study the most welding processes as well as the most pipe variations welded by orbital welding systems mainly for oil and gas pipeline applications are explained. The welding results show that Gas Metal Arc Welding (GMAW) and its variants like Surface Tension Transfer (STT) and modified short circuit are the most preferred processes in the welding of root pass and can be replaced to the Gas Tungsten Arc Welding (GTAW) in many applications. Furthermore, dual-tandem gas metal arc welding technique is currently considered the most efficient method in the welding of fill pass. Orbital GTAW process mostly is applied for applications ranging from single run welding of thin walled stainless tubes to multi run welding of thick walled pipes. Flux cored arc welding process is faster process with higher deposition rate and recently this process is getting more popular in pipe welding applications. Also, combination of gas metal arc welding and Nd:YAG laser has shown acceptable results in girth welding of land pipelines for oil and gas industry. This Master’s thesis can be implemented as a guideline in welding of pipes and tubes to achieve higher quality and efficiency. Also, this research can be used as a base material for future investigations to supplement present finding.

Underwater Remote Welding Technology for Offshore Structures

The construction of offshore structures, equipment and devices requires a high level of mechanical reliability in terms of strength, toughness and ductility. One major site for mechanical failure, the weld joint region, needs particularly careful examination, and weld joint quality has become a major focus of research in recent times. Underwater welding carried out offshore faces specific challenges affecting the mechanical reliability of constructions completed underwater. The focus of this thesis is on improvement of weld quality of underwater welding using control theory. This research work identifies ways of optimizing the welding process parameters of flux cored arc welding (FCAW) during underwater welding so as to achieve desired weld bead geometry when welding in a water environment. The weld bead geometry has no known linear relationship with the welding process parameters, which makes it difficult to determine a satisfactory weld quality. However, good weld bead geometry is achievable by controlling the welding process parameters. The doctoral dissertation comprises two sections. The first part introduces the topic of the research, discusses the mechanisms of underwater welding and examines the effect of the water environment on the weld quality of wet welding. The second part comprises four research papers examining different aspects of underwater wet welding and its control and optimization. Issues considered include the effects of welding process parameters on weld bead geometry, optimization of FCAW process parameters, and design of a control system for the purpose of achieving a desired bead geometry that can ensure a high level of mechanical reliability in welded joints of offshore structures. Artificial neural network systems and a fuzzy logic controller, which are incorporated in the control system design, and a hybrid of fuzzy and PID controllers are the major control dynamics used. This study contributes to knowledge of possible solutions for achieving similar high weld quality in underwater wet welding as found with welding in air. The study shows that carefully selected steels with very low carbon equivalent and proper control of the welding process parameters are essential in achieving good weld quality. The study provides a platform for further research in underwater welding. It promotes increased awareness of the need to improve the quality of underwater welding for offshore industries and thus minimize the risk of structural defects resulting from poor weld quality.

Sliding wear of weld layers with application to cane mill shaft rebuilding

Three welding procedures used to rebuild worn shafts in sugar cane mills were analysed: two submerged arc welding processes and one flux cored arc welding (FCAW) process. Sliding wear tests were in accordance with ASTM G 77 standard, using rings of welding material, blocks of bronze SAE 67, and oil as lubricant. The worn surfaces of rings and blocks were analysed by scanning electron microscopy to determine the wear mechanisms. High contact pressure, high operating temperature, and low relative speed were applied in sliding wear tests to match the conditions in sugar cane mills. Transferred material and evidence of adhesive junctions were detected. Additionally, hardened fragments produced abrasive grooves on the worn surfaces. The welding deposits that presented strong adhesion on the worn surface showed higher mass loss than the materials that presented more abrasive characteristics. Plastic mechanical properties were measured and related to the mass loss. The tested materials presented similar hardness but different yield stress and hardening coefficient. A relationship between wear, strain hardening coefficient, and yield stress was found. The welding deposit that presented the highest hardening coefficient showed the highest mass loss, with evidence of severe adhesion on the worn surface.

Comportamento à fadiga de juntas soldadas de aços tipo 460M com fios fluxados

Trabalho Final de Mestrado para obtenção do grau de Mestre em Engenharia Mecânica

Hitsausparametrien vaikutus rakenneteräksen MAG-hitsin laatuun

Työn tavoitteena oli löytää teräksen S355 MAG alapienahitsaukselle, 6mm:n levypaksuudelle sellaiset parametri-ikkunat, joissa hitsin ja perusaineen liittyminen on mahdollisimman jouheva. Hitsin laadunja hitsausparametrien välille pyritiin löytämään matemaattista korrelaatiota. Työ painottui hitsin muotoon sekä hitsin ja perusaineen liittymiseen. Työstä saatuja tuloksia käytettiin hitsattaessa väsytyskoekappaleita mutta niiden tutkiminen ei sisältynyt tähän työhön. Työssä haettiin parametreja a-mitaltaan 4mm:n alapienahitsille kahdeksalle yleisesti käytetylle hitsauslangalle, joista kolme oli umpilankaa, neljä metallitäytelankaa ja yksi rutiilitäytelanka ja kaasuina käytettiin kahta argon hiilidioksidi seoskaasua ja kahta argon helium seoskaasua.

Hitsausmenetelmät ja niiden kehittämismahdollisuudet painelaitteiden valmistuksessa

Työn tavoitteena oli painelaitteiden hitsaustuotannon kehittäminen. Keinoina olivat käytössä olevien hitsausprosessienkehittäminen tai niiden käytön tehostaminen ja mahdollisesti muiden hitsausprosessien, kuten plasma-, laser- tai hybridihitsauksen, käyttöönotto. Työn teoriaosassa käsiteltiin painelaitteiden valmistuksessa käytettävät hitsausprosessit ja niiden kehittämiskeinot, hitsauskustannuksen muodostuminen sekä miten näihin kustannuksiin voidaan vaikuttaa. Lisäksi tarkasteltiin painelaitteiden valmistuksessa käytettävien materiaalien hitsattavuutta ja laadunvarmistusta. Tutkimusosuudessa käytiin läpi valmistuksen nykytila ja tehtiin tuotannon analysointi kehittämiskohteeksi valitulle lämmönsiirtimelle. Kehitysehdotuksenatuotannon tehostamiseksi ehdotettiin MAG-täytelanka- ja jauhekaarihitsauksen käytön lisäämistä. Lisäksi ehdotettiin juurituen käyttöä ja hitsauksen mekanisoinnin lisäämistä. Plasma- tai hybridihitsauksen käytöllä todettiin pystyttävän lyhentämään läpimenoaikoja. Ennen laitteistohankintojen tekoa täytyy tehdä lisäselvityksiä soveltuvuuden ja kannattavuuden varmistamiseksi.

Lean Duplex -terästen hitsaus

Viime vuosien aikana tapahtunut nikkelin hinnan nouseminen on vaikuttanut austeniittis-ferriittisten ruostumattomien terästen, ns. duplex -terästen kehittämiseen. Niukkaseosteisemmissa lean duplex -teräksissä seostetun nikkelin määrää on vähennetty ja sitä on korvattu typellä ja mangaanilla. Nämä muutokset ko. terästen seostuksessa aiheuttavat haasteita hitsaukselle, erityisesti austeniitti-ferriitti -suhteen säilyttämisessä, sekä sitä kautta iskusitkeyden ja korroosio-ominaisuuksien säilyttämiselle. Suurempi typen osuus myös lisää teräksen hitsisulan viskositeettia, mikä heikentää juuripalkojen hitsauksessa tunkeumaa. Tässsä diplomityössä on tutkittu keinoja helpottaa paksujen (yli 20 mm) lean duplex -teräslevyjen hitsausta käytännön näkökulmasta, sekä parantaa hitsattujen levyjen iskusitkeyttä. Hitsauskokeilla löydettiin hitsausta helpottavia menetelmiä ja kokeista saatiin karsimalla valikoitua hitsausarvot, joilla pystytään hitsaamaan painelaitedirektiivin mukaisesti hyväksyttäviä hitsejä lean duplex -laatuihin LDX2101 ja UR2202.

Vedenalainen hitsaus

Tässä kandidaatintyössä esitellään ensin vedenalainen hitsaus yleisesti. Työssä käydään läpi vedenalaisen hitsauksen eri pääalueet ja niissä käytetyt hitsaustekniikat, sekä tarkastellaan veden vaikutusta hitsiin. Työ sisältää myös materiaali esimerkkejä, joita vedenalaisessa hitsauksessa käytetään. Vedenalainen hitsaus toimii asennus- ja korjaushitsauksena. Hitsausprosessit, joita työssä käsitellään, ovat puikko-, täytelanka- ja kitkahitsaus. Näitä hitsaustekniikoita käytetään märkähitsauksessa, mikä poikkeaa selvästi kuivassa ympäristössä tapahtuvaan hitsaamiseen, jossa hitsi ei pääse välittömästi kosketukseen veden kanssa. Työn tarkoituksena on antaa informaatiota vedenalaisesta hitsauksesta ja sen hyödyntämisestä hitsaustekniikassa.

Efeito dos parâmetros de pulso sobre as características geométricas e desempenho da soldagem com arame tubular autoprotegido e corrente pulsada

Pós-graduação em Engenharia Mecânica - FEB

Avaliação da influência de aplicação de vibração mecânica na microestrutura e em características mecânicas de juntas do aço inoxidável martensítico CA6NM soldadas pelo processo FCAW

O aço inoxidável martensítico ASTM A743 CA6NM é utilizado para produzir componentes especiais para turbinas hidráulicas, devido às suas boas propriedades mecânicas combinadas com alta resistência à corrosão e cavitação e uma boa soldabilidade. As turbinas hidráulicas são produzidas por meio de múltiplos passes de solda em peças espessas obtidas por fundição. Durante a operação, estes componentes estão sujeitos à erosão por cavitação e trincas em regiões tensionadas, que são reparados também por meio de soldagem. Após o processo de soldagem, um tratamento térmico pós-soldagem é comumente utilizado para aliviar as tensões residuais. Porém, existem dificuldades significativas para a realização de tratamento térmico nas turbinas hidráulicas, tais como a complexidade da geometria de solda, a possibilidade de distorção no caso de quaisquer cargas mecânicas, dificuldade em aquecer simetricamente, e também o tratamento térmico pode causar degradação das propriedades do material. Assim, existe um grande interesse no desenvolvimento de procedimentos de soldagem que elevem a tenacidade ao impacto e evitem o tratamento térmico pós-soldagem. Neste trabalho, a aplicação de vibrações mecânicas durante e após a soldagem para aliviar tensões residuais foram avaliadas em juntas de aço inoxidável martensítico CA6NM soldadas pelo processo Flux Cored Arc Welding (FCAW). A utilização de vibrações mecânicas para reduzir e redistribuir as tensões residuais das estruturas soldadas através da aplicação de carga vibratória pode gerar muitos benefícios. Testes de impacto Charpy (-20 °C), ensaios de tração e dobramento foram realizados conforme ASME IX, e perfis de microdureza nas diferentes regiões da solda foram conduzidos para a caracterização mecânica das juntas soldadas. A caracterização microestrutural foi realizada utilizando difração de raios X, microscopia óptica e microscopia eletrônica de varredura (MEV). Os resultados de propriedades mecânicas das amostras vibradas atenderam as exigências especificadas por norma, na qual o processo com tratamento térmico é recomendado para a soldagem deste tipo de aço, visando atingir os níveis de tenacidade do material original. Com relação à microestrutura não foram observados alterações significativas para as amostras vibradas em comparação com a condição \"como soldado\", porém para a condição com tratamento térmico pós-soldagem foi observado uma pequena quantidade de austenita retida, que são precipitadas após o tratamento térmico e permanecem finamente distribuídas após o resfriamento e auxiliam no ganho de tenacidade das juntas soldadas.

Metal transfer mapping for FCAW process by using near-infrared filming

In the Flux Cored Arc Welding (FCAW) process, the transfer of filler metal (metal transfer modes) to the base material to accomplish the weld bead determines the weld quality and therefore studies of such phenomena is demanded. Thus, in this work, the metal transfer through the FCAW process is investigated by filming the phenomena with the assist of near infrared visualization. During the literature survey, it was found that this technic has not been used so far for analyzing the FCAW process. It must be pointed out that the radiation emitted from the weld arc, fumes and particles (spattering) in this process represent a barrier for these studies based in the process visualization. The monitoring of metal transfer for FCAW process was carried out within the operational envelope of voltage and wire feed speed with the electrode E71T-1 (1.2 mm diameter) and Ar+25%CO2 as a shielding gas. A local developed near infrared filming with frame rate of 300 Hz was employed for metal transfer visualization in order to contribute to a better understanding of this process and evaluating characteristics of metal transfer, unlike previous studies, which used shadowgraph technique. It can clearly be seen how the droplet is created and transferred in this process and also identify the different modes of metal transfer by changing the parameters of voltage and wire feed speed in metal transfer maps. The final result of this study is the metal transfer mode maps, which establish suitable conditions and provide the basis for developing arc control strategies for the FCAW process.

The copper cladding of steel by the submerged arc welding method

The literature available on submerged arc welding of copper and copper alloys, submerged arc welding with strip electrodes, and related areas has been reviewed in depth. Copper cladding of mild steel substrates by deposition from strip electrodes using the submerged arc welding process has been successful. A wide range of parameters, and several fluxes have been investigated. The range of deposit compositions is 66.4% Cu to 95.7% Cu. The weld beads have been metallographically examined using optical and electron microscopy. Equating weld beads to a thermodynamical equivalent of iron has proven to be an accurate and simplified means of handling quantitative data for multicomponent welds. Empirical equations derived using theoretical considerations characterize the weld bead dimensions as functions of the welding parameters and hence composition. The melting rate for strip electrodes is dependent upon the current-voltage product. Weld nugget size is increased by increased thermal transfer efficiencies resulting from stirring which is current dependent. The presence of Fe2O3 in a flux has been demonstrated to diminish electrode melting rate and drastically increase penetration, making flux choice the prime consideration in cladding operations. A theoretical model for welding with strip electrodes and the submerged arc process is presented.

Gas tungsten arc welding of NiTi shape memory alloy

Shape memory alloys are characterized by the ability of recovering their initial shape after being deformed and by superelasticity. Since the discovery of these alloys, a new field of interest emerged not only for the scientific community but also to many industries. However, these alloys present poor machinability which constitute a constrain in the design of complex components for new applications. Thus, the demand for joining techniques able to join these alloys without compromising their properties became of great importance to enlarge the complexity of existing applications. Literature shows that these alloys are joined mainly using laser welding. In the present study, similar NiTi butt joints, were produced using TIG welding. The welds were performed in 1.5 mm thick plates across the rolling direction. A special fixture and gas assist device was designed and manufactured. Also a robot arm was adapted to accommodate the welding torch to assure the repeatability of the welding parameters. Welds were successfully achieved without macroscopic defects, such as pores and distortions. Very superficial oxidation was seen on the top surface due to insufficient shielding gas flow on the weld face. The welded joints were mechanically tested and structurally characterized. Testing methods were used to evaluate macro and microstructure, as well as the phase transformation temperatures, the mechanical single and cyclic behaviour and the shape recovery ability. Differential Scanning Calorimetry (DSC), Scanning Electron Microscopy (SEM), Energy Dispersive Spectroscopy (EDS), microhardness measurements were techniques also used to evaluate the welded joints. A depletion in Ni in the fusion zone was seen, as well as a shift in Ms temperature. For strain values of 4% the accumulated irrecoverable strain was of about 30% and increased with the strain imposed during cycling. Nevertheless, a complete recovery of initial shape was observed when testing the shape memory effect on a dedicated device that introduces a deformation of 6.7%. That is, the welding procedure does not remove the ability of the specimens to recover their initial shape.