Energetic, ecologic and fluid-dynamic analysis of a fluidized bed gasifier operating with sugar cane bagasse

This work aims to study the thermodynamic, ecological and fluid-dynamic aspects of a circulating fluidized bed gasifier using sugar cane bagasse as biomass, in order to estimate a model of its normal operation. In the initial stage was analysed the composition of biomass selected (sugar cane bagasse) and its lower heating value (LHV) was calculated. The energy balance of the gasifier was done, being the volumetric flow of air, synthesis gas and biomass estimated. Also the power produced by this gasifier was theoretically estimated. Then the circulating fluidized bed gasifier was designed for operation with approximately 100 kg/h of processed biomass. Cross-sectional area of the reactor, feeder size, diameter of the exit zone of the gases and minimum height of the expanded bed were selected. Some bed gasifier hydrodynamic factors were also studied. The minimum fluidization velocity, fluidization terminal velocity, and average fluidizing velocity were calculated, in order to understand the fluid-dynamic behaviour of gasification of this fuel. It was obtained a theoretical model that can support a possible prototype of circulating fluidized bed gasifier biomass. Finally, there were studied the ecological aspects of the gasifier, through an overall methodology. Ecological efficiencies were estimated for two scenarios: first considering the carbon cycle and thereafter disregarding the carbon cycle. In both cases, it can be proved the ecological viability of the project. © 2013 Elsevier Ltd. All rights reserved.

Study on biomass circulation and gasification performance in a clapboard-type internal circulating fluidized bed gasifier

We investigated the solid particle flow characteristics and biomass gasification in a clapboard-type internal circulating fluidized bed reactor. The effect of fluidization velocity on particle circulation rate and pressure distribution in the bed showed that fluidization velocities in the high and low velocity zones were the main operational parameters controlling particle circulation. The maximum internal circulation rates in the low velocity zone came almost within the range of velocities in the high velocity zone, when uH/umf = 2.2-2.4 for rice husk and uH/umf = 3.5-4.5 for quartz sand. In the gasification experiment, the air equvalence ratio (ER) was the main controlling parameter. Rice husk gasification gas had a maximum heating value of around 5000 kJ/m3 when ER = 0.22-0.26, and sawdust gasification gas reached around 6000-6500 kJ/m3 when ER = 0.175-0.24. The gasification efficiency of rice husk reached a maximum of 77% at ER = 0.28, while the gasification efficiency of sawdust reached a maximum of 81% at ER = 0.25.

The design and operation of a new clapboard-type internal circulating fluidized-bed gasifier

The design and operation of a new clapboard-type internal circulating fluidized-bed gasifier is proposed in this article. By arranging the clapboard in the bed, the gasifier is thus divided into two regions, which are characterized by different fluidization velocities. The bed structure is designed so that it can guide the circulating flow passing through the two regions, and therefore the feedstock particles entrained in the flow experience longer residence time. The experimental results based on the present new design, operating in the temperature range of 790 degrees C-850 degrees C, indicate that the gas yield is from 1.6-1.9 Nm(3)/kg feedstock, the gas enthalpies are 5,345 kJ/Nm(3) for wood chip and 4,875 kJ/m(3) for rice husk, and a gasification efficiency up to 75% can be obtained.

Fluid-dynamic assessment of sugarcane bagasse to use as feedstock in bubbling fluidized bed gasifiers

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Evaluation of thermochemical biomass conversion in fluidized bed

Dado o aumento acelerado dos preços dos combustíveis fósseis e as incertezas quanto à sua disponibilidade futura, tem surgido um novo interesse nas tecnologias da biomassa aplicadas à produção de calor, eletricidade ou combustíveis sintéticos. Não obstante, para a conversão termoquímica de uma partícula de biomassa sólida concorrem fenómenos bastante complexos que levam, em primeiro lugar, à secagem do combustível, depois à pirólise e finalmente à combustão ou gasificação propriamente ditas. Uma descrição relativamente incompleta de alguns desses estágios de conversão constitui ainda um obstáculo ao desenvolvimento das tecnologias que importa ultrapassar. Em particular, a presença de elevados conteúdos de matéria volátil na biomassa põe em evidência o interesse prático do estudo da pirólise. A importância da pirólise durante a combustão de biomassa foi evidenciada neste trabalho através de ensaios realizados num reator piloto de leito fluidizado borbulhante. Verificou-se que o processo ocorre em grande parte à superfície do leito com chamas de difusão devido à libertação de voláteis, o que dificulta o controlo da temperatura do reator acima do leito. No caso da gasificação de biomassa a pirólise pode inclusivamente determinar a eficiência química do processo. Isso foi mostrado neste trabalho durante ensaios de gasificação num reator de leito fluidizado de 2MWth, onde um novo método de medição permitiu fechar o balanço de massa ao gasificador e monitorizar o grau de conversão da biomassa. A partir destes resultados tornou-se clara a necessidade de descrever adequadamente a pirólise de biomassa com vista ao projeto e controlo dos processos. Em aplicações de engenharia há particular interesse na estequiometria e propriedades dos principais produtos pirolíticos. Neste trabalho procurou-se responder a esta necessidade, inicialmente através da estruturação de dados bibliográficos sobre rendimentos de carbonizado, líquidos pirolíticos e gases, assim como composições elementares e poderes caloríficos. O resultado traduziu-se num conjunto de parâmetros empíricos de interesse prático que permitiram elucidar o comportamento geral da pirólise de biomassa numa gama ampla de condições operatórias. Para além disso, propôs-se um modelo empírico para a composição dos voláteis que pode ser integrado em modelos compreensivos de reatores desde que os parâmetros usados sejam adequados ao combustível ensaiado. Esta abordagem despoletou um conjunto de ensaios de pirólise com várias biomassas, lenhina e celulose, e temperaturas entre os 600 e 975ºC. Elevadas taxas de aquecimento do combustível foram alcançadas em reatores laboratoriais de leito fluidizado borbulhante e leito fixo, ao passo que um sistema termo-gravimétrico permitiu estudar o efeito de taxas de aquecimento mais baixas. Os resultados mostram que, em condições típicas de processos de combustão e gasificação, a quantidade de voláteis libertada da biomassa é pouco influenciada pela temperatura do reator mas varia bastante entre combustíveis. Uma análise mais aprofundada deste assunto permitiu mostrar que o rendimento de carbonizado está intimamente relacionado com o rácio O/C do combustível original, sendo proposto um modelo simples para descrever esta relação. Embora a quantidade total de voláteis libertada seja estabelecida pela composição da biomassa, a respetiva composição química depende bastante da temperatura do reator. Rendimentos de espécies condensáveis (água e espécies orgânicas), CO2 e hidrocarbonetos leves descrevem um máximo relativamente à temperatura para dar lugar a CO e H2 às temperaturas mais altas. Não obstante, em certas gamas de temperatura, os rendimentos de algumas das principais espécies gasosas (e.g. CO, H2, CH4) estão bem correlacionados entre si, o que permitiu desenvolver modelos empíricos que minimizam o efeito das condições operatórias e, ao mesmo tempo, realçam o efeito do combustível na composição do gás. Em suma, os ensaios de pirólise realizados neste trabalho permitiram constatar que a estequiometria da pirólise de biomassa se relaciona de várias formas com a composição elementar do combustível original o que levanta várias possibilidades para a avaliação e projeto de processos de combustão e gasificação de biomassa.

Modeling dimensional shrinkage of shaped foods in fluidized bed drying

Three particular geometrical shapes of parallelepiped, cylinder and sphere were selected from cut beans (length : diameter = 1: 1, 2:1, 3: 1), potatoes (aspect ratio = 1:1, 2:1, 3:1) and peas, respectively. The dimensional shrinkage behavior was studied in a batch fluidized bed at three drying temperatures of 30, 40 and 50C. Relative humidity of hot air was kept at 15%. Dimensional shrinkage was plotted using a nondimensional moisture ratio and the shrinkage behavior of the selected foods was modeled with simple mathematical models.

Adapting data processing to compare model and experiment accurately: A discrete element model and magnetic resonance measurements of a 3d cylindrical fluidized bed

Discrete element modeling is being used increasingly to simulate flow in fluidized beds. These models require complex measurement techniques to provide validation for the approximations inherent in the model. This paper introduces the idea of modeling the experiment to ensure that the validation is accurate. Specifically, a 3D, cylindrical gas-fluidized bed was simulated using a discrete element model (DEM) for particle motion coupled with computational fluid dynamics (CFD) to describe the flow of gas. The results for time-averaged, axial velocity during bubbling fluidization were compared with those from magnetic resonance (MR) experiments made on the bed. The DEM-CFD data were postprocessed with various methods to produce time-averaged velocity maps for comparison with the MR results, including a method which closely matched the pulse sequence and data processing procedure used in the MR experiments. The DEM-CFD results processed with the MR-type time-averaging closely matched experimental MR results, validating the DEM-CFD model. Analysis of different averaging procedures confirmed that MR time-averages of dynamic systems correspond to particle-weighted averaging, rather than frame-weighted averaging, and also demonstrated that the use of Gaussian slices in MR imaging of dynamic systems is valid. © 2013 American Chemical Society.

Cluster identification and characterization in the riser of a circulating fluidized bed from numerical simulation results

A methodology of identification and characterization of coherent structures mostly known as clusters is applied to hydrodynamic results of numerical simulation generated for the riser of a circulating fluidized bed. The numerical simulation is performed using the MICEFLOW code, which includes the two-fluids IIT's hydrodynamic model B. The methodology for cluster characterization that is used is based in the determination of four characteristics, related to average life time, average volumetric fraction of solid, existing time fraction and frequency of occurrence. The identification of clusters is performed by applying a criterion related to the time average value of the volumetric solid fraction. A qualitative rather than quantitative analysis is performed mainly owing to the unavailability of operational data used in the considered experiments. Concerning qualitative analysis, the simulation results are in good agreement with literature. Some quantitative comparisons between predictions and experiment were also presented to emphasize the capability of the modeling procedure regarding the analysis of macroscopic scale coherent structures. (c) 2007 Elsevier B.V. All rights reserved.

Modelling and simulation of biomass gasification in a circulating fluidized bed reactor

Computational Fluid Dynamics (CFD) has found great acceptance among the engineering community as a tool for research and design of processes that are practically difficult or expensive to study experimentally. One of these processes is the biomass gasification in a Circulating Fluidized Bed (CFB). Biomass gasification is the thermo-chemical conversion of biomass at a high temperature and a controlled oxygen amount into fuel gas, also sometime referred to as syngas. Circulating fluidized bed is a type of reactor in which it is possible to maintain a stable and continuous circulation of solids in a gas-solid system. The main objectives of this thesis are four folds: (i) Develop a three-dimensional predictive model of biomass gasification in a CFB riser using advanced Computational Fluid Dynamic (CFD) (ii) Experimentally validate the developed hydrodynamic model using conventional and advanced measuring techniques (iii) Study the complex hydrodynamics, heat transfer and reaction kinetics through modelling and simulation (iv) Study the CFB gasifier performance through parametric analysis and identify the optimum operating condition to maximize the product gas quality. Two different and complimentary experimental techniques were used to validate the hydrodynamic model, namely pressure measurement and particle tracking. The pressure measurement is a very common and widely used technique in fluidized bed studies, while, particle tracking using PEPT, which was originally developed for medical imaging, is a relatively new technique in the engineering field. It is relatively expensive and only available at few research centres around the world. This study started with a simple poly-dispersed single solid phase then moved to binary solid phases. The single solid phase was used for primary validations and eliminating unnecessary options and steps in building the hydrodynamic model. Then the outcomes from the primary validations were applied to the secondary validations of the binary mixture to avoid time consuming computations. Studies on binary solid mixture hydrodynamics is rarely reported in the literature. In this study the binary solid mixture was modelled and validated using experimental data from the both techniques mentioned above. Good agreement was achieved with the both techniques. According to the general gasification steps the developed model has been separated into three main gasification stages; drying, devolatilization and tar cracking, and partial combustion and gasification. The drying was modelled as a mass transfer from the solid phase to the gas phase. The devolatilization and tar cracking model consist of two steps; the devolatilization of the biomass which is used as a single reaction to generate the biomass gases from the volatile materials and tar cracking. The latter is also modelled as one reaction to generate gases with fixed mass fractions. The first reaction was classified as a heterogeneous reaction while the second reaction was classified as homogenous reaction. The partial combustion and gasification model consisted of carbon combustion reactions and carbon and gas phase reactions. The partial combustion considered was for C, CO, H2 and CH4. The carbon gasification reactions used in this study is the Boudouard reaction with CO2, the reaction with H2O and Methanation (Methane forming reaction) reaction to generate methane. The other gas phase reactions considered in this study are the water gas shift reaction, which is modelled as a reversible reaction and the methane steam reforming reaction. The developed gasification model was validated using different experimental data from the literature and for a wide range of operating conditions. Good agreement was observed, thus confirming the capability of the model in predicting biomass gasification in a CFB to a great accuracy. The developed model has been successfully used to carry out sensitivity and parametric analysis. The sensitivity analysis included: study of the effect of inclusion of various combustion reaction; and the effect of radiation in the gasification reaction. The developed model was also used to carry out parametric analysis by changing the following gasifier operating conditions: fuel/air ratio; biomass flow rates; sand (heat carrier) temperatures; sand flow rates; sand and biomass particle sizes; gasifying agent (pure air or pure steam); pyrolysis models used; steam/biomass ratio. Finally, based on these parametric and sensitivity analysis a final model was recommended for the simulation of biomass gasification in a CFB riser.