New geopolymeric binder based on fluid catalytic cracking catalyst residue (FCC)

This paper provides information about the synthesis and mechanical properties of geopolymers based on fluid catalytic cracking catalyst residue (FCC). FCC was alkali activated with solutions containing different SiO2/Na2O ratios. The microstructure and mechanical properties were analysed by using several instrumental techniques. FCC geopolymers are mechanically stable, yielding compressive strength about 68 MPa when mortars are cured at 65 degrees C during 3 days. The results confirm the viability of producing geopolymers based on FCC. (C) 2012 Elsevier B.V. All rights reserved.

Alkali activated materials based on fluid catalytic cracking catalyst residue (FCC): Influence of SiO2/Na2O and H 2O/FCC ratio on mechanical strength and microstructure

Reuse of industrial and agricultural wastes as supplementary cementitious materials (SCMs) in concrete and mortar productions contribute to sustainable development. In this context, fluid catalytic cracking catalyst residue (spent FCC), a byproduct from the petroleum industry and petrol refineries, have been studied as SCM in blended Portland cement in the last years. Nevertheless, another environmental friendly alternative has been conducted in order to produce alternative binders with low CO2 emissions. The use of aluminosilicate materials in the production of alkali-activated materials (AAMs) is an ongoing research topic which can present low CO2 emissions associated. Hence, this paper studies some variables that can influence the production of AAM based on spent FCC. Specifically, the influence of SiO 2/Na2O molar ratio and the H2O/spent FCC mass ratio on the mechanical strength and microstructure are assessed. Some instrumental techniques, such as SEM, XRD, pH and electrical conductivity measurements, and MIP are performed in order to assess the microstructure of formed alkali-activated binder. Alkali activated mortars with compressive strength up to 80 MPa can be formed after curing for 3 days at 65°C. The research demonstrates the potential of spent FCC to produce alkali-activated cements and the importance of SiO2/Na2O molar ratio and the H2O/spent FCC mass ratio in optimising properties and microstructure. © 2013 Elsevier Ltd. All rights reserved.

Refinery Nonconventional Feedstocks: Influence of the Coprocessing of Vacuum Gas Oil and Low Density Polyethylene in Fluid Catalytic Cracking Unit on Full Range Gasoline Composition

Gasoline coming from refinery fluid catalytic cracking (FCC) unit is a major contributor to the total commercial grade gasoline pool. The contents of the FCC gasoline are primarily paraffins, naphthenes, olefins, aromatics, and undesirables such as sulfur and sulfur containing compounds in low quantities. The proportions of these components in the FCC gasoline invariable determine its quality as well as the performance of the associated downstream units. The increasing demand for cleaner and lighter fuels significantly influences the need not only for novel processing technologies but also for alternative refinery and petrochemical feedstocks. Current and future clean gasoline requirements include increased isoparaffins contents, reduced olefin contents, reduced aromatics, reduced benzene, and reduced sulfur contents. The present study is aimed at investigating the effect of processing an unconventional refinery feedstock, composed of blend of vacuum gas oil (VGO) and low density polyethylene (LDPE) on FCC full range gasoline yields and compositional spectrum including its paraffins, isoparaffins, olefins, napthenes, and aromatics contents distribution within a range of operating variables of temperature (500–700 °C) and catalyst-feed oil ratio (CFR 5–10) using spent equilibrium FCC Y-zeolite based catalyst in a FCC pilot plant operated at the University of Alicante’s Research Institute of Chemical Process Engineering (RICPE). The coprocessing of the oil-polymer blend led to the production of gasoline with very similar yields and compositions as those obtained from the base oil, albeit, in some cases, the contribution of the feed polymer content as well as the processing variables on the gasoline compositional spectrum were appreciated. Carbon content analysis showed a higher fraction of the C9–C12 compounds at all catalyst rates employed and for both feedstocks. The gasoline’s paraffinicity, olefinicity, and degrees of branching of the paraffins and olefins were also affected in various degrees by the scale of operating severity. In the majority of the cases, the gasoline aromatics tended toward the decrease as the reactor temperature was increased. While the paraffins and iso-paraffins gasoline contents were relatively stable at around 5 % wt, the olefin contents on the other hand generally increased with increase in the FCC reactor temperature.

Conversion of low density polyethylene into fuel through co-processing with vacuum gas oil in a fluid catalytic cracking riser reactor

In this work, mixtures of vacuum gas oil and low density polyethylene, a major component of common industrial and consumer household plastics, were pyrolytically co-processed in a fluid catalytic cracking (FCC) riser reactor as a viable alternative for the energy and petrochemical revalorisation of plastic wastes into valuable petrochemical feedstocks and fuel within an existing industrial technology. Using equilibrium FCC catalyst, the oil–polymer blends were catalytically cracked at different processing conditions of temperatures between 773 K and 973 K and catalyst feed ratios of 5:1, 7:1 and 10:1. The influence of each of these processing parameters on the cracking gas and liquid yield patterns were studied and presented. Further analysed and presented are the different compositional distributions of the obtained liquids and gaseous products. The analysis of the results obtained revealed that with very little modifications to existing process superstructure, yields and compositional distributions of products from the fluid catalytic cracking of the oil–polymer blend in many cases were very similar to those of the processed oil feedstock, bringing to manifest the viability of the feedstock co-processing without significant detriments to FCC product yields and quality.

Implementação de um tuboexpansor na refinaria do Planalto Paulista – REPLAN com objetivo do aproveitamento da energia contida nos gases residuais do FCC – Fluid Catalytic Cracking na geração de energia elétrica

The steel type AISI 4130 (ultra-high strength steel) is an alloy of low carbon and its main alloying elements are chromium and molybdenum, which improves the toughness of the weld metal. It has numerous applications, especially where the need for high mechanical strength. It is widely used in equipment used by the aviation industry, such as cradle-tomotor, and this is the motivation for this study. Cots are of fundamental importance, because the engine supports and maintains balance in the fixed landing gear. This equipment is subjected to intense loading cycles, whose fractures caused by fatigue are constantly observed. Will be determined the effects caused by re-welding the structure of aeronautical equipment, and will also study the microstructure of the metal without welding. The studies will be done on materials used in aircraft, which was given to study. The results provide knowledge of microstructure to evaluate any type of fracture that maybe caused by fatigue. Fatigue is a major cause of aircraft accidents and incidents occurred, which makes the study of the microstructure of the metal, weld and re-solder the knowledge essential to the life of the material. The prevention and control of the process of fatigue in aircraft are critical, since the components are subjected to greater responsibility cyclic loading

Realizing the Commercial Potential of Hierarchical Zeolites: New Opportunities in Catalytic Cracking

Many approaches to mesoporous zeolites have been reported. The preparation of mesoporous zeolite Y, as the most widely used zeolite in catalysis, its properties, and its application in fluid catalytic cracking (FCC) and hydrocracking are reviewed. Finally, the scale-up and use of mesostrutured zeolite Y on an industrial scale are described, as the first commercial application of hierarchical zeolites.

Catalytic cracking of tar derived from rice hull gasification over palygorskite-supported Fe and Ni

The catalytic performance of Fe–Ni/PG (PG: palygorskite) catalysts pre-calcined and reduced at 500 ◦C for catalytic decomposition of tar derived through rice hull gasification was investigated. The materials were characterized by using X-ray diffraction, hydrogen temperature reduction, and transmission electron microscopy. The results showed that ferrites with spinel structure ((Fe, Ni)3O4) were formed during preparation of bimetallic systems during calcination and reduction of the precursors (Fe–Ni/PG catalysts) and NiO metal oxide particles were formed over Fe6–Ni9/PG catalyst. The obtained experimental data showed that Fe–Ni/PG catalysts had greater catalytic activity than natural PG. Tar removal using Fe6–Ni9/PG catalyst was as high as Fe10–Ni6/PG catalyst (99.5%). Fe6–Ni9/PG showed greater catalytic activity with greater H2 yield and showed stronger resistance to carbon deposition, attributed to the presence of NiO nanoparticles. Thus, the addition of nickel and iron oxides played an important role in catalytic cracking of rice hull biomass tar.

Effect of preparation method of palygorskite-supported Fe and Ni catalysts on catalytic cracking of biomass tar

In this study, the effect of catalyst preparation and additive precursors on the catalytic decomposition of biomass using palygorskite-supported Fe and Ni catalysts was investigated. The catalysts were characterized by X-ray diffraction (XRD) and transmission electron microscopy (TEM). It is concluded that the most active additive precursor was Fe(NO3)3·9H2O. As for the catalyst preparation method, co-precipitation had superiority over incipient wetness impregnation at low Fe loadings.

Characterization and catalytic performance of Fe3Ni8/palygorskite for catalytic cracking of benzene

Catalytic decomposition is a very attractive way to convert tar components into H2, CO and other useful chemicals. The performance of Fe3Ni8/PG (palygorskite, PG) reduced in hydrogen at different temperatures for the catalytic decomposition of benzene has been assessed. Benzene was used as the model biomass tar. The effects of calcination atmosphere, temperatures and benzene concentration on catalytic cracking of benzene were measured. The results of XRD (X-Ray Diffraction), TEM (Transmission Electron Microscope), TPR (Temperature Program Reduction), TPSR (Temperature Program Surface Reduction), TC (Total Carbon), the reactivity component and reaction mechanism over Fe3Ni8/PG for catalytic cracking of benzene are discussed. The results showed particles of awaruite (Fe, Ni) about 2–30 nm were found on the surface of palygorskite by TEM when the calcination temperature was 600 °C. Particles with size smaller than 30 nm were obtained on all prepared Fe3Ni8/PG catalysts as shown by XRD. The nanoparticles proved to be the reactive component for catalytic cracking of benzene and the increase of active particle size caused the decrease in the reactivity of Fe3Ni8/PG. Fe3Ni8/PG annealed in hydrogen at 600 °C was proved to have the best reactivity in experiments (45% hydrogen yield). High concentration benzene (448 g/m3) accelerated the formation of carbon deposition. However, iron oxide decreases carbon deposition and increases the stability of catalyst for catalytic cracking of benzene. The application of Fe3Ni8/PG catalysts was proved a very effective catalyst for the catalytic cracking of benzene.

Catalytic cracking of acetic acid to acetic anhydride

Catalytic cracking of acetic acid using triethyl phosphate and silica gel catalysts was investigated. The desired reaction leading to ketene is accompanied by side reactions: two parallel with respect to acetic acid decomposition and the consecutive ketene decomposition reactions. Effect of temperature, catalyst concentration, space velocity, and pressure was studied in detail. Triethyl phosphate was found to be a much better catalyst than silica gel. The optimum yield of ketene was obtained at 750° C, 100 mm. of Hg pressure, and apparent contact time of 5.687 × 10-4 hour.

Catalytic Cracking and Heat Sink Capacity of Aviation Kerosene Under Supercritical Conditions

Catalytic cracking of China no. 3 aviation kerosene using a zeolite catalyst was investigated under supercritical conditions. A three-stage heating/cracking system was specially designed to be capable of heating 0.8 kg kerosene to a temperature of 1050 K and pressure of 7.0 MPa with maximum mass flow rate of 80 g/s. Sonic nozzles of different diameters were used to calibrate and monitor the mass flow rate of the cracked fuel mixture. With proper experiment arrangements, the mass flow rate per unit throat area of the cracked fuel mixture was found to well correlate with the extent of fuel conversion. The gaseous products obtained from fuel cracking under different conditions were also analyzed using gas chromatography. Composition analysis showed that the average molecular weight of the resulting gaseous products and the fuel mass conversion percentage were a strong function of the fuel temperature and were only slightly affected by the fuel pressure. The fuel conversion was also shown to depend on the fuel residence time in the reactor, as expected. Furthermore, the heat sink levels due to sensible heating and endothermic cracking were determined and compared at varying test conditions. It was found that at a fuel temperature of similar to 1050 K, the total heat sink reached similar to 3.4 MJ/kg, in which chemical heat sink accounted for similar to 1.5 MJ/kg.

Production of light olefins and aromatic hydrocarbons through catalytic cracking of naphtha at lowered temperature

Naphtha catalytic cracking were carried out at 650 degrees C over modified ZSM-5. Light olefins and BTX could be obtained over the catalysts. The products showed variable distribution with different catalyst modification. Some modification, such as Fe, Cu and La favored the BTX generation and P and Mg modification favored the light olefins production. In N-2 stream cracking catalyzed by LaZSM-5, more than 50% naphtha feed were converted to BTX, while in steam cracking, with an improved modified catalyst, P, La/ZSM-5, naphtha can be converted to light olefins with high activity and long-term stability.

Butene catalytic cracking to propene and ethene over potassium modified ZSM-5 catalysts

Catalytic cracking of butene over potassium modified ZSM-5 catalysts was carried out in a fixed-bed microreactor. By increasing the K loading on the ZSM-5, butene conversion and ethene selectivity decreased almost linearly, while propene selectivity increased first, then passed through a maximum (about 50% selectivity) with the addition of ca. 0.7-1.0% K, and then decreased slowly with further increasing of the K loading. The reaction conditions were 620 degrees C, WHSV 3.5 h(-1), 0.1 MPa 1-butene partial pressure and 1 h of time on stream. Both by potassium modification of the ZSM-5 zeolite and by N(2) addition in the butene feed could enhance the selectivity towards propene effectively, but the catalyst stability did not show any improvement. On the other hand, addition of water to the butene feed could not only increase the butene conversion, but also improve the stability of the 0.7%K/ZSM-5 catalyst due to the effective removal of the coke formed, as demonstrated by the TPO spectra. XRD results indicated that the ZSM-5 structure of the 0.07% K/ZSM-5 catalyst was not destroyed even under this serious condition of adding water at 620 degrees C.

Catalytic cracking of tars derived from rice hull gasification over goethite and palygorskite

Palygorskite (P), goethite (G), and hydrothermally synthesized goethite (HG) were used as supports for Fe and Ni. The catalytic activity of these materials was investigated involving in P, G and HG (supported Fe and Ni) for catalytic decomposition of biomass tar derived from rice hull gasification. The materials were characterized by X-ray diffraction (XRD), X-ray fluorescence (XRF), and transmission electron microscopy (TEM) with an energy dispersive X-ray (EDS). The catalytic activity of P for removal of tar was significantly better than that of G and HG. However, the activity of G with 6 mass% Ni labeled as Ni6/G (tar conversion 94.6%), which was equal to Fe6Ni6/P (94.4%), was better than Ni6/P (64.4%) and Ni6/HG (46.7%). When the loading of Ni (mass%) was 6 mass% on G, tar conversion had the best value (94.6%) and yield of gaseous products reached 486.9, 167.8 and 22.2 mL/(g·tar) for H2, CO, CH4, respectively. The catalytic activity of goethite supported Ni was better in improving tar conversion and improving increased yield of H2, CO, CH4, which was attributed to the existence of Al/Fe substitution of goethite

Estudo de pirólise catalítica de biomassa em escala piloto para melhoramento da qualidade do bio-óleo

A pirólise rápida é um processo para conversão térmica de uma biomassa sólida em altos rendimentos de um produto líquido chamado de bio-óleo. Uma das alternativas para geração de um bio-óleo com menor teor de oxigênio é uso de catalisadores nos reatores de pirólise, ao invés de um inerte, num processo chamado de pirólise catalítica. O objetivo deste trabalho foi testar catalisadores comerciais, um ácido e outro básico, em uma unidade piloto de leito fluidizado circulante. O catalisador ácido utilizado foi o Ecat, proveniente de uma unidade industrial de craqueamento catalítico fluido (FCC), e como catalisador básico foi utilizado uma hidrotalcita. Os resultados foram comparados com testes utilizando um material inerte, no caso uma sílica. Uma unidade piloto de FCC do CENPES foi adaptada para realizar os testes de pirólise catalítica. Após fase de modificação e testes de condicionamento, foi comprovada a viabilidade na utilização da unidade piloto adaptada. Contudo, devido a limitações operacionais, maiores tempos de residência tiveram que ser aplicados no reator, configurando o processo como pirólise intermediária. Foram então realizados testes com os três materiais nas temperaturas de 450C e 550C. Os resultados mostraram que o aumento do tempo de residência dos vapores de pirólise teve um impacto significativo nos rendimentos dos produtos quando comparada com o perfil encontrado na literatura para pirólise rápida, pois devido ao incremento das reações secundárias, produziu maiores rendimentos de coque e água, e menores rendimentos de bio-óleo. O Ecat e a hidrotalcita se apresentaram mais efetivos em termos de desoxigenação. O primeiro apresentou maiores taxas de desoxigenação via desidratação e a hidrotalcita apresentou maior capacidade para descarboxilação. Contudo, o uso de Ecat e hidrotalcita não se mostrou adequado para uso em reatores de pirólise intermediária, pois acentuou ainda mais as reações secundárias, gerando um produto com alto teor de água e baixo teor de compostos orgânicos no bio-óleo, além de produzirem mais coque. À temperatura de 450C estes efeitos foram mais pronunciados. Em termos de caracterização química, a condição de pirólise intermediária apontou para a produção de bio-óleos com perfil fenólico, sendo a sílica o que proporcionou os melhores rendimentos, principalmente a temperatura de 550C, sendo superiores aos encontrados na literatura. Analisando as composições dos bio-óleos sob a ótica da produção de biocombustíveis, nenhum dos materiais testados apresentou rendimentos consideráveis em hidrocarbonetos. De maneira geral, a sílica foi o que proporcionou os melhores resultados em termos de rendimento e qualidade do bio-óleo. Sua menor área superficial e sua característica de inerte se mostraram mais adequados para o processo de pirólise intermediária, onde a contribuição das reações secundárias em fase gasosa é elevada em função do tempo de residência no reator