Smart antennas in software radio base stations

The application of adaptive antenna techniques to fixed-architecture base stations has been shown to offer wide-ranging benefits, including interference rejection capabilities or increased coverage and spectral efficiency.Unfortunately, the actual implementation ofthese techniques to mobile communication scenarios has traditionally been set back by two fundamental reasons. On one hand, the lack of flexibility of current transceiver architectures does not allow for the introduction of advanced add-on functionalities. On the other hand, theoften oversimplified models for the spatiotemporal characteristics of the radio communications channel generally give rise toperformance predictions that are, in practice, too optimistic. The advent of software radio architectures represents a big step toward theintroduction of advanced receive/transmitcapabilities. Thanks to their inherent flexibilityand robustness, software radio architecturesare the appropriate enabling technology for theimplementation of array processing techniques.Moreover, given the exponential progression ofcommunication standards in coexistence andtheir constant evolution, software reconfigurabilitywill probably soon become the only costefficientalternative for the transceiverupgrade. This article analyzes the requirementsfor the introduction of software radio techniquesand array processing architectures inmultistandard scenarios. It basically summarizesthe conclusions and results obtained withinthe ACTS project SUNBEAM,1 proposingalgorithms and analyzing the feasibility ofimplementation of innovative and softwarereconfigurablearray processing architectures inmultistandard settings.

A VLF to UHF propagation model for evaluation of high-speed railway electromagnetic interference in RF monitoring base-stations

Considering that recent european high-speed railway system has a traction power system of kV 50 Hz, which causes electromagnetic emission for the outside world, it is important to dimension the railway system emissions, using a frequency/distance dependent propagation model. This paper presents an enhanced theoretical model for VLF to UHF propagation, railway system oriented. It introduces the near field approach (crucial in low frequency propagation) and also considers the source characteristics and type of measuring antenna. Simulations are presented, and comparisons are set with earlier far field models. Using the developed model, a real case study was performed in partnership with Refer Telecom (portuguese telecom operator for railways). The new propagation model was used in order to predict the future high-speed railway electromagnetic emissions in the Lisbon north track. The results show the model's prediction capabilities and also its applicability to realistic scenarios.

Identification d’une architecture à base de composants dans une application orientée objets à l’aide d’une analyse dynamique

Un système, décrit avec un grand nombre d'éléments fortement interdépendants, est complexe, difficile à comprendre et à maintenir. Ainsi, une application orientée objet est souvent complexe, car elle contient des centaines de classes avec de nombreuses dépendances plus ou moins explicites. Une même application, utilisant le paradigme composant, contiendrait un plus petit nombre d'éléments, faiblement couplés entre eux et avec des interdépendances clairement définies. Ceci est dû au fait que le paradigme composant fournit une bonne représentation de haut niveau des systèmes complexes. Ainsi, ce paradigme peut être utilisé comme "espace de projection" des systèmes orientés objets. Une telle projection peut faciliter l'étape de compréhension d'un système, un pré-requis nécessaire avant toute activité de maintenance et/ou d'évolution. De plus, il est possible d'utiliser cette représentation, comme un modèle pour effectuer une restructuration complète d'une application orientée objets opérationnelle vers une application équivalente à base de composants tout aussi opérationnelle. Ainsi, La nouvelle application bénéficiant ainsi, de toutes les bonnes propriétés associées au paradigme composants. L'objectif de ma thèse est de proposer une méthode semi-automatique pour identifier une architecture à base de composants dans une application orientée objets. Cette architecture doit, non seulement aider à la compréhension de l'application originale, mais aussi simplifier la projection de cette dernière dans un modèle concret de composant. L'identification d'une architecture à base de composants est réalisée en trois grandes étapes: i) obtention des données nécessaires au processus d'identification. Elles correspondent aux dépendances entre les classes et sont obtenues avec une analyse dynamique de l'application cible. ii) identification des composants. Trois méthodes ont été explorées. La première utilise un treillis de Galois, la seconde deux méta-heuristiques et la dernière une méta-heuristique multi-objective. iii) identification de l'architecture à base de composants de l'application cible. Cela est fait en identifiant les interfaces requises et fournis pour chaque composant. Afin de valider ce processus d'identification, ainsi que les différents choix faits durant son développement, j'ai réalisé différentes études de cas. Enfin, je montre la faisabilité de la projection de l'architecture à base de composants identifiée vers un modèle concret de composants.

A Key Management Protocol for Wireless Sensor Networks with Multiple Base Stations

Most of the proposed key management protocols for wireless sensor networks (WSNs) in the literature assume that a single base station is used and that the base station is trustworthy. However, there are applications in which multiple base stations are used and the security of the base stations must be considered. This paper investigates a key management protocol in wireless sensor networks which include multiple base stations. We consider the situations in which both the base stations and the sensor nodes can be compromised. The proposed key management protocol, mKeying, includes two schemes, a key distribution scheme, mKeyDist, supporting multiple base stations in the network, and a key revocation scheme, mKeyRev, used to efficiently remove the compromised nodes from the network. Our analyses show that the proposed protocol is efficient and secure against the compromise of the base stations and the sensor nodes.

Feasibility of future epidemiological studies on possible health effects of mobile phone base stations

The increasing deployment of mobile communication base stations led to an increasing demand for epidemiological studies on possible health effects of radio frequency emissions. The methodological challenges of such studies have been critically evaluated by a panel of scientists in the fields of radiofrequency engineering/dosimetry and epidemiology. Strengths and weaknesses of previous studies have been identified. Dosimetric concepts and crucial aspects in exposure assessment were evaluated in terms of epidemiological studies on different types of outcomes. We conclude that in principle base station epidemiological studies are feasible. However, the exposure contributions from all relevant radio frequency sources have to be taken into account. The applied exposure assessment method should be piloted and validated. Short to medium term effects on physiology or health related quality of life are best investigated by cohort studies. For long term effects, groups with a potential for high exposure need to first be identified; for immediate effect, human laboratory studies are the preferred approach.

Analysis of the lateral diffuse metal-oxide semiconductor (LDMOS) power amplifier for cellular base stations

The primary purpose of this thesis was to present a theoretical large-signal analysis to study the power gain and efficiency of a microwave power amplifier for LS-band communications using software simulation. Power gain, efficiency, reliability, and stability are important characteristics in the power amplifier design process. These characteristics affect advance wireless systems, which require low-cost device amplification without sacrificing system performance. Large-signal modeling and input and output matching components are used for this thesis. Motorola's Electro Thermal LDMOS model is a new transistor model that includes self-heating affects and is capable of small-large signal simulations. It allows for most of the design considerations to be on stability, power gain, bandwidth, and DC requirements. The matching technique allows for the gain to be maximized at a specific target frequency. Calculations and simulations for the microwave power amplifier design were performed using Matlab and Microwave Office respectively. Microwave Office is the simulation software used in this thesis. The study demonstrated that Motorola's Electro Thermal LDMOS transistor in microwave power amplifier design process is a viable solution for common-source amplifier applications in high power base stations. The MET-LDMOS met the stability requirements for the specified frequency range without a stability-improvement model. The power gain of the amplifier circuit was improved through proper microwave matching design using input/output-matching techniques. The gain and efficiency of the amplifier improve approximately 4dB and 7.27% respectively. The gain value is roughly .89 dB higher than the maximum gain specified by the MRF21010 data sheet specifications. This work can lead to efficient modeling and development of high power LDMOS transistor implementations in commercial and industry applications.

Implementação em hardware reconfigurável de método de separação de dados hiperespetrais

Relatório do Trabalho Final de Mestrado para obtenção do grau de Mestre em Engenharia de Electrónica e Telecomunicações

On the choice of posittioning and cluster size for fixed relay stations in a LTE network

The long term evolution (LTE) is one of the latest standards in the mobile communications market. To achieve its performance, LTE networks use several techniques, such as multi-carrier technique, multiple-input-multiple-output and cooperative communications. Inside cooperative communications, this paper focuses on the fixed relaying technique, presenting a way for determining the best position to deploy the relay station (RS), from a set of empirical good solutions, and also to quantify the associated performance gain using different cluster size configurations. The best RS position was obtained through realistic simulations, which set it as the middle of the cell's circumference arc. Additionally, it also confirmed that network's performance is improved when the number of RSs is increased. It was possible to conclude that, for each deployed RS, the percentage of area served by an RS increases about 10 %. Furthermore, the mean data rate in the cell has been increased by approximately 60 % through the use of RSs. Finally, a given scenario with a larger number of RSs, can experience the same performance as an equivalent scenario without RSs, but with higher reuse distance. This conduces to a compromise solution between RS installation and cluster size, in order to maximize capacity, as well as performance.

Sistemi riconfigurabili a basso consumo per applicazioni di monitoraggio distribuito

The term Ambient Intelligence (AmI) refers to a vision on the future of the information society where smart, electronic environment are sensitive and responsive to the presence of people and their activities (Context awareness). In an ambient intelligence world, devices work in concert to support people in carrying out their everyday life activities, tasks and rituals in an easy, natural way using information and intelligence that is hidden in the network connecting these devices. This promotes the creation of pervasive environments improving the quality of life of the occupants and enhancing the human experience. AmI stems from the convergence of three key technologies: ubiquitous computing, ubiquitous communication and natural interfaces. Ambient intelligent systems are heterogeneous and require an excellent cooperation between several hardware/software technologies and disciplines, including signal processing, networking and protocols, embedded systems, information management, and distributed algorithms. Since a large amount of fixed and mobile sensors embedded is deployed into the environment, the Wireless Sensor Networks is one of the most relevant enabling technologies for AmI. WSN are complex systems made up of a number of sensor nodes which can be deployed in a target area to sense physical phenomena and communicate with other nodes and base stations. These simple devices typically embed a low power computational unit (microcontrollers, FPGAs etc.), a wireless communication unit, one or more sensors and a some form of energy supply (either batteries or energy scavenger modules). WNS promises of revolutionizing the interactions between the real physical worlds and human beings. Low-cost, low-computational power, low energy consumption and small size are characteristics that must be taken into consideration when designing and dealing with WSNs. To fully exploit the potential of distributed sensing approaches, a set of challengesmust be addressed. Sensor nodes are inherently resource-constrained systems with very low power consumption and small size requirements which enables than to reduce the interference on the physical phenomena sensed and to allow easy and low-cost deployment. They have limited processing speed,storage capacity and communication bandwidth that must be efficiently used to increase the degree of local ”understanding” of the observed phenomena. A particular case of sensor nodes are video sensors. This topic holds strong interest for a wide range of contexts such as military, security, robotics and most recently consumer applications. Vision sensors are extremely effective for medium to long-range sensing because vision provides rich information to human operators. However, image sensors generate a huge amount of data, whichmust be heavily processed before it is transmitted due to the scarce bandwidth capability of radio interfaces. In particular, in video-surveillance, it has been shown that source-side compression is mandatory due to limited bandwidth and delay constraints. Moreover, there is an ample opportunity for performing higher-level processing functions, such as object recognition that has the potential to drastically reduce the required bandwidth (e.g. by transmitting compressed images only when something ‘interesting‘ is detected). The energy cost of image processing must however be carefully minimized. Imaging could play and plays an important role in sensing devices for ambient intelligence. Computer vision can for instance be used for recognising persons and objects and recognising behaviour such as illness and rioting. Having a wireless camera as a camera mote opens the way for distributed scene analysis. More eyes see more than one and a camera system that can observe a scene from multiple directions would be able to overcome occlusion problems and could describe objects in their true 3D appearance. In real-time, these approaches are a recently opened field of research. In this thesis we pay attention to the realities of hardware/software technologies and the design needed to realize systems for distributed monitoring, attempting to propose solutions on open issues and filling the gap between AmI scenarios and hardware reality. The physical implementation of an individual wireless node is constrained by three important metrics which are outlined below. Despite that the design of the sensor network and its sensor nodes is strictly application dependent, a number of constraints should almost always be considered. Among them: • Small form factor to reduce nodes intrusiveness. • Low power consumption to reduce battery size and to extend nodes lifetime. • Low cost for a widespread diffusion. These limitations typically result in the adoption of low power, low cost devices such as low powermicrocontrollers with few kilobytes of RAMand tenth of kilobytes of program memory with whomonly simple data processing algorithms can be implemented. However the overall computational power of the WNS can be very large since the network presents a high degree of parallelism that can be exploited through the adoption of ad-hoc techniques. Furthermore through the fusion of information from the dense mesh of sensors even complex phenomena can be monitored. In this dissertation we present our results in building several AmI applications suitable for a WSN implementation. The work can be divided into two main areas:Low Power Video Sensor Node and Video Processing Alghoritm and Multimodal Surveillance . Low Power Video Sensor Nodes and Video Processing Alghoritms In comparison to scalar sensors, such as temperature, pressure, humidity, velocity, and acceleration sensors, vision sensors generate much higher bandwidth data due to the two-dimensional nature of their pixel array. We have tackled all the constraints listed above and have proposed solutions to overcome the current WSNlimits for Video sensor node. We have designed and developed wireless video sensor nodes focusing on the small size and the flexibility of reuse in different applications. The video nodes target a different design point: the portability (on-board power supply, wireless communication), a scanty power budget (500mW),while still providing a prominent level of intelligence, namely sophisticated classification algorithmand high level of reconfigurability. We developed two different video sensor node: The device architecture of the first one is based on a low-cost low-power FPGA+microcontroller system-on-chip. The second one is based on ARM9 processor. Both systems designed within the above mentioned power envelope could operate in a continuous fashion with Li-Polymer battery pack and solar panel. Novel low power low cost video sensor nodes which, in contrast to sensors that just watch the world, are capable of comprehending the perceived information in order to interpret it locally, are presented. Featuring such intelligence, these nodes would be able to cope with such tasks as recognition of unattended bags in airports, persons carrying potentially dangerous objects, etc.,which normally require a human operator. Vision algorithms for object detection, acquisition like human detection with Support Vector Machine (SVM) classification and abandoned/removed object detection are implemented, described and illustrated on real world data. Multimodal surveillance: In several setup the use of wired video cameras may not be possible. For this reason building an energy efficient wireless vision network for monitoring and surveillance is one of the major efforts in the sensor network community. Energy efficiency for wireless smart camera networks is one of the major efforts in distributed monitoring and surveillance community. For this reason, building an energy efficient wireless vision network for monitoring and surveillance is one of the major efforts in the sensor network community. The Pyroelectric Infra-Red (PIR) sensors have been used to extend the lifetime of a solar-powered video sensor node by providing an energy level dependent trigger to the video camera and the wireless module. Such approach has shown to be able to extend node lifetime and possibly result in continuous operation of the node.Being low-cost, passive (thus low-power) and presenting a limited form factor, PIR sensors are well suited for WSN applications. Moreover techniques to have aggressive power management policies are essential for achieving long-termoperating on standalone distributed cameras needed to improve the power consumption. We have used an adaptive controller like Model Predictive Control (MPC) to help the system to improve the performances outperforming naive power management policies.

Advanced handover procedure for cellular communication systems

Third Generation cellular communication systems are expected to support mixed cell architecture in which picocells, microcells and macrocells are used to achieve full coverage and increase the spectral capacity. Supporting higher numbers of mobile terminals and the use of smaller cells will result in an increase in the number of handovers, and consequently an increase in the time delays required to perform these handovers. Higher time delays will generate call interruptions and forced terminations, particularly for time sensitive applications like real-time multimedia and data services. Currently in the Global System for Mobile communications (GSM), the handover procedure is initiated and performed by the fixed part of the Public Land Mobile Network (PLMN). The mobile terminal is only capable of detecting candidate base stations suitable for the handover; it is the role of the network to interrogate a candidate base station for a free channel. Handover signalling is exchanged via the fixed network and the time delay required to perform the handover is greatly affected by the levels of teletraffic handled by the network. In this thesis, a new handover strategy is developed to reduce the total time delay for handovers in a microcellular system. The handover signalling is diverted from the fixed network to the air interface to prevent extra delays due to teletraffic congestion, and to allow the mobile terminal to exchange signalling directly with the candidate base station. The new strategy utilises Packet Reservation Multiple Access (PRMA) technique as a mechanism to transfer the control of the handover procedure from the fixed network to the mobile terminal. Simulation results are presented to show a dramatic reduction in the handover delay as compared to those obtained using fixed channel allocation and dynamic channel allocation schemes.

Análise do desempenho da tecnologia 4G LTE

O objectivo deste trabalho passa pelo desenvolvimento de uma ferramenta de simulação dinâmica de recursos rádio em LTE no sentido descendente, com recurso à Framework OMNeT++. A ferramenta desenvolvida permite realizar o planeamento das estações base, simulação e análise de resultados. São descritos os principais aspectos da tecnologia de acesso rádio, designadamente a arquitectura da rede, a codificação, definição dos recursos rádio, os ritmos de transmissão suportados ao nível de canal e o mecanismo de controlo de admissão. Foi definido o cenário de utilização de recursos rádio que inclui a definição de modelos de tráfego e de serviços orientados a pacotes e circuitos. Foi ainda considerado um cenário de referência para a verificação e validação do modelo de simulação. A simulação efectua-se ao nível de sistema, suportada por um modelo dinâmico, estocástico e orientado por eventos discretos de modo a contemplar os diferentes mecanismos característicos da tecnologia OFDMA. Os resultados obtidos permitem a análise de desempenho dos serviços, estações base e sistema ao nível do throughput médio da rede, throughput médio por eNodeB e throughput médio por móvel para além de permitir analisar o contributo de outros parâmetros designadamente, largura de banda, raio de cobertura, perfil dos serviços, esquema de modulação, entre outros. Dos resultados obtidos foi possível verificar que, considerando um cenário com estações base com raio de cobertura de 100 m obteve-se um throughput ao nível do utilizador final igual a 4.69494 Mbps, ou seja, 7 vezes superior quando comparado a estações base com raios de cobertura de 200m.

Avaliação do impacto energético resultante da utilização de repetidores em sistema LTE

Actualmente uma grande preocupação global refere-se ao continuo aumento do custo da energia, resultante da procura e do impacto ambiental. A escalada do custo da energia obriga a procura sistemática de melhores sistemas que permitam diminuir esse custo. Nas comunicações móveis sem fios a economia de energia obtida pelo aumento da eficiência do equipamento das estaçõesbase é insuficiente, pelo qual é necessário também encontrar soluções ao nível da arquitectura. O LTE define os repetidores como um recurso de baixo consumo para aumentar a cobertura e ou capacidade da rede. Nesta dissertação é avaliado um método de economia de energia baseado na substituição de uma estação-base central, circundada por outras estações-base, por um determinado número de repetidores. A cobertura e a capacidade resultante é avaliada assim como a energia poupada. Os resultados obtidos permitem verificar que se pode poupar até 1 000,00 € anuais e 20 kW diários com a substituição de uma estação-base, completamente rodeada por outras estações, por um número de repetidores compreendido entre 1 e 9 dependendo da ISD (até 1750 m). Verifica-se ainda um ganho de eficiência energética de até 13% ao nível do sistema.

TTCN testing of WCDMA base station operation and maintenance software

TTCN-kieltä käytetään testitapausten määrittelemiseen tietoliikennejärjestelmissä. Nykyään TTCN:stä on tullut yhä suositumpi tapa toteuttaa testitapauksia. TTCN tarjoaa hyvän ja yksinkertaisen tavan muuntaa käsin testattavat testitapaukset automatisoiduiksi. Tämän diplomityön yhteydessä toteutettiin TTCN testitapaukset WCDMA -tukiaseman käyttö- ja kunnossapito- (O&M) ohjelmistolle. Ohjelmistoa on käytetty myös toisen sukupolven tukiasemissa, mutta kolmannen sukupolven tukiasemissa sillä on huomattavasti isompi rooli. WCDMA -tukiasemassa O&M käsittelee muun muassa tukiaseman käynnistyksen, virhetilanteet ja valvoo tukiaseman komponentteja. Ensimmäisiä tehtäviä diplomityötä tehdessä oli valita ne testitapaukset, jotka olisivat mahdollisia ja hyödyllisiä toteuttaa TTCN:n avulla. Testitapaukset valittiin valmiina olleista testitapausten kuvauksista. Valitut testitapaukset toteutettiin käyttäen rinnakkaista ja modulaarista TTCN-kieltä ja testattiin WCDMA -tukiasemaa vasten käyttäen TTCN Tester ohjelmistoa. Tämän diplomityön yhteydessä toteutettuja testitapauksia käytetään varmistamaan, että tukiasema voi toipua erilaisista virhetilanteista O&M ohjelmiston avulla. Testitapauksia WCDMA -tukiasemaa vasten ajettaessa varmistetaan myös, että O&M ohjelmisto toimii määrittelyn mukaisesti eri tilanteissa. Toteutetut testi tapaukset korvaavat nykyään käsin testatut O&M testi tapaukset tukiaseman O&M ohjelmistoa testatessa. Automatisoidut testi tapaukset tekevät O&M ohjelmiston testaamisen merkittävästi nopeammaksi ja helpommaksi.

Green-Markov models - new optimization strategies: a case study for user allocation in co-channel macro/femto networks

ABSTRACT: The femtocell concept aims to combine fixed-line broadband access with mobile telephony using the deployment of low-cost, low-power third and fourth generation base stations in the subscribers' homes. While the self-configuration of femtocells is a plus, it can limit the quality of service (QoS) for the users and reduce the efficiency of the network, based on outdated allocation parameters such as signal power level. To this end, this paper presents a proposal for optimized allocation of users on a co-channel macro-femto network, that enable self-configuration and public access, aiming to maximize the quality of service of applications and using more efficiently the available energy, seeking the concept of Green networking. Thus, when the user needs to connect to make a voice or a data call, the mobile phone has to decide which network to connect, using the information of number of connections, the QoS parameters (packet loss and throughput) and the signal power level of each network. For this purpose, the system is modeled as a Markov Decision Process, which is formulated to obtain an optimal policy that can be applied on the mobile phone. The policy created is flexible, allowing different analyzes, and adaptive to the specific characteristics defined by the telephone company. The results show that compared to traditional QoS approaches, the policy proposed here can improve energy efficiency by up to 10%.

Estudo comparativo de sistemas de rádio digital sobre fibra aplicado a C-RAN

O objetivo deste trabalho é comparar aspectos relacionados ao uso de Multiplexação por Subportadora (SCM) em um sistema de transmissão de Rádio Digital sobre Fibra (DRoF) aplicado à Arquitetura de Acesso a Rádio Centralizado (C-RAN). Para isso, foram criados dois cenários que fazem uso da tecnologia DRoF, onde no primeiro, três subportadoras são transmitidas em um comprimento de onda e, para o segundo cenário, três comprimentos de onda são transmitidos, onde cada um possui uma única subportadora. Para ambas configurações é visado alimentar unidades de rádio remoto (RRH) localizadas na torre de transmissão. São analisados aspectos de desempenho da recepção, alcance das redes e complexidade do sistema para cada um dos cenários propostos. Além disso, são mostrados passo a passo como os sistemas foram construídos utilizando o software de simulação VPITransmissionMaker. Foram considerados para cada subportadora uma taxa de 250 Mbps, modulação 16-QAM, centrados na frequência de 5GHz. Os resultados obtidos demonstram que, para SCM-DRoF, uma Taxa de Erro de Bit (BER) de 10^-6 é mantida constante para enlaces de até 20 km. No segundo modelo, sem uso de SCM, um desempenho similar foi verificado, contudo com alcance de até 40 km. Dado o contexto da aplicação, os fatores desempenho e distância levam a crer que ambos cenários de transmissão podem ser utilizadas para C-RAN. Contudo, levando em consideração o custo e a complexidade no domínio óptico, o sistema utilizando SCM, comparativamente, possui mais vantagens. Conclui-se então que o uso de SCM apresenta-se como uma forte opção para aplicações no contexto das novas tecnologias de redes de acesso móvel.