Experimental validation of a proposed single-phase five-level active rectifier operating with model predictive current control

This paper presents a model predictive current control applied to a proposed single-phase five-level active rectifier (FLAR). This current control strategy uses the discrete-time nature of the active rectifier to define its state in each sampling interval. Although the switching frequency is not constant, this current control strategy allows to follow the reference with low total harmonic distortion (THDF). The implementation of the active rectifier that was used to obtain the experimental results is described in detail along the paper, presenting the circuit topology, the principle of operation, the power theory, and the current control strategy. The experimental results confirm the robustness and good performance (with low current THDF and controlled output voltage) of the proposed single-phase FLAR operating with model predictive current control.

Simulation of OWES with five-Level converter linked to the grid: Harmonic assessment

This paper deals with a computing simulation for an offshore wind energy system taking into account the influence of the marine waves action throughout the floating platform. The wind energy system has a variable-speed turbine equipped with a permanent magnet synchronous generator and a full-power five level converter, injecting energy into the electric grid through a high voltage alternate current link. A reduction on the unbalance of the voltage in the DC-link capacitors of the five-level converter is proposed by a strategic selection of the output voltage vectors. The model for the drive train of the wind energy system is a two mass model, including the dynamics of the floating platform. A case study is presented and the assessment of the quality of the energy injected into the electric grid is discussed.

Single-phase active rectifier selection for fault tolerant machine

A fault tolerant, 5-phase PM generator has been developed for use on the low pressure (LP) shaft of an aircraft gas turbine engine. The machine operates at variable speed and therefore has a variable voltage, variable frequency electrical output (VVVF). The generator is to be used to provide a 350V DC bus for distribution throughout the aircraft, and a study has been carried out that identifies the most suitable AC-DC converter topology for this machine in terms of losses, electrical component ratings, filtering requirements and circuit complexity.

Blade pitch control malfunction simulation in a wind energy conversion system with MPC five-level converter

This paper is on a wind energy conversion system simulation of a transient analysis due to a blade pitch control malfunction. The aim of the transient analysis is the study of the behavior of a back-to-back multiple point clamped five-level full-power converter implemented in a wind energy conversion system equipped with a permanent magnet synchronous generator. An alternate current link connects the system to the grid. The drive train is modeled by a three-mass model in order to simulate the dynamic effect of the wind on the tower. The control strategy is based on fractional-order control. Unbalance voltages in the DC-link capacitors are lessen due to the control strategy, balancing the capacitor banks voltages by a selection of the output voltage vectors. Simulation studies are carried out to evaluate not only the system behavior, but also the quality of the energy injected into the electric grid.

Emotions in organizations: A multi-level perspective

Recent years have seen an upsurge of interest in the study of emotions in organizations. Research, however, has been hampered by the ephemeral nature of emotions and a lack of an integrated multi-level model. This article therefore presents a five-level model of emotions in organizations. At the lowest level is within-person variation, defined in terms of affective events theory. Levels of the model then proceed through individual, dyadic relationship, group, and organization-wide perspectives. The article also outlines the neurophysiological processes that underlie the experience, perception, and communication of emotion; it concludes with a discussion of implications for research and practice.

Fast optimum-predictive control and capacitor voltage balancing strategy for bipolar back-to-back NPC converters in high-voltage direct current transmission systems

Multilevel power converters have been introduced as the solution for high-power high-voltage switching applications where they have well-known advantages. Recently, full back-to-back connected multilevel neutral point diode clamped converters (NPC converter) have been used inhigh-voltage direct current (HVDC) transmission systems. Bipolar-connected back-to-back NPC converters have advantages in long-distance HVDCtransmission systems over the full back-to-back connection, but greater difficulty to balance the dc capacitor voltage divider on both sending and receiving end NPC converters. This study shows that power flow control and dc capacitor voltage balancing are feasible using fast optimum-predictive-based controllers in HVDC systems using bipolar back-to-back-connected five-level NPC multilevel converters. For both converter sides, the control strategytakes in account active and reactive power, which establishes ac grid currents in both ends, and guarantees the balancing of dc bus capacitor voltages inboth NPC converters. Additionally, the semiconductor switching frequency is minimised to reduce switching losses. The performance and robustness of the new fast predictive control strategy, and its capability to solve the DC capacitor voltage balancing problem of bipolar-connected back-to-back NPCconverters are evaluated.

Five-year evolution of drug prescribing in a university adult intensive care unit

Introduction: Drug prescription is difficult in ICUs as prescribers are many, drugs expensive and decisions complex. In our ICU, specialist clinicians (SC) are entitled to prescribe a list of specific drugs, negotiated with intensive care physicians (ICP). The objective of this investigation was to assess the 5-year evolution of quantity and costs of drug prescription in our adult ICU and identify the relative costs generated by ICP or SC. Methods: Quantities and costs of drugs delivered on a quarterly basis to the adult ICU of our hospital between 2004 and 2008 were extracted from the pharmacy database by ATC code, an international five-level classification system. Within each ATC first level, drugs with either high level of consumption, high costs or large variations in quantities and costs were singled out and split by type of prescriber, ICP or SC. Cost figures used were drug purchase prices by the hospital pharmacy. Results: Over the 5-year period, both quantities and costs of drugs increased, following a nonsteady, nonparallel pattern. Four ATC codes accounted for 80% of both quantities and costs, with ATC code B (blood and haematopoietic organs) amounting to 63% in quantities and 41% in costs, followed by ATC code J (systemic anti-infective, 20% of the costs), ATC code N (nervous system, 11% of the costs) and ATC code C (cardiovascular system, 8% of the costs). Prescription by SC amounted to 1% in drug quantities, but 19% in drug costs. The rate of increase in quantities and costs was seven times larger for ICP than for SC (Figure 1 overleaf ). Some peak values in costs and quantities were related to a very limited number of patients. Conclusions: A 5-year increase in quantities and costs of drug prescription in an ICU is a matter of concern. Rather unexpectedly, total costs and cost increases were generated mainly by ICP. A careful follow-up is necessary to try influencing this evolution through an institutional policy co-opted by all professional categories involved in the process.

A Wireless Charging System Applying Phase-Shift and Amplitude Control to Maximize Efficiency and Extractable Power

Wireless power transfer (WPT) is an emerging technology with an increasing number of potential applications to transfer power from a transmitter to a mobile receiver over a relatively large air gap. However, its widespread application is hampered due to the relatively low efficiency of current Wireless power transfer (WPT) systems. This study presents a concept to maximize the efficiency as well as to increase the amount of extractable power of a WPT system operating in nonresonant operation. The proposed method is based on actively modifying the equivalent secondary-side load impedance by controlling the phase-shift of the active rectifier and its output voltage level. The presented hardware prototype represents a complete wireless charging system, including a dc-dc converter which is used to charge a battery at the output of the system. Experimental results are shown for the proposed concept in comparison to a conventional synchronous rectification approach. The presented optimization method clearly outperforms state-of-the-art solutions in terms of efficiency and extractable power.

Analysis and improvement of performance in LCL filter-based PWM rectifier/inverter application using hybrid damping approach

A hybrid passive-active damping solution with improved system stability margin and enhanced dynamic performance is proposed for high power grid interactive converters. In grid connected active rectifier/inverter application, line side LCL filter improves the high frequency attenuation and makes the converter compatible with the stringent grid power quality regulations. Passive damping though offers a simple and reliable solution but it reduces overall converter efficiency. Active damping solutions do not increase the system losses but can guarantee the stable operation up to a certain speed of dynamic response which is limited by the maximum bandwidth of the current controller. This paper examines this limit and introduces a concept of hybrid passive-active damping solution with improved stability margin and high dynamic performance for line side LCL filter based active rectifier/inverter applications. A detailed design, analysis of the hybrid approach and trade-off between system losses and dynamic performance in grid connected applications are reported. Simulation and experimental results from a 10 kVA prototype demonstrate the effectiveness of the proposed solution. An analytical study on system stability and dynamic response with the variations of various controller and passive filter parameters is presented.

Emergence of multidrug-resistant tuberculosis in a community-based directly observed treatment programme in rural South Africa

OBJECTIVE: Although little studied in developing countries, multidrug-resistant tuberculosis (MDR-TB) is considered a major threat. We report the molecular epidemiology, clinical features and outcome of an emerging MDR-TB epidemic. METHODS: In 1996 all tuberculosis suspects in the rural Hlabisa district, South Africa, had sputum cultured, and drug susceptibility patterns of mycobacterial isolates were determined. Isolates with MDR-TB (resistant to both isoniazid and rifampicin) were DNA fingerprinted by restriction fragment length polymorphism (RFLP) using IS6110 and polymorphic guanine-cytosine-rich sequence-based (PGRS) probes. Patients with MDR-TB were traced to determine outcome. Data were compared with results from a survey of drug susceptibility done in 1994. RESULTS: The rate of MDR-TB among smear-positive patients increased six-fold from 0.36% (1/275) in 1994 to 2.3% (13/561) in 1996 (P = 0.04). A further eight smear-negative cases were identified in 1996 from culture, six of whom had not been diagnosed with tuberculosis. MDR disease was clinically suspected in only five of the 21 cases (24%). Prevalence of primary and acquired MDR-TB was 1.8% and 4.1%, respectively. Twelve MDR-TB cases (67%) were in five RFLP-defined clusters. Among 20 traced patients, 10 (50%) had died, five had active disease (25%) and five (25%) were apparently cured. CONCLUSIONS: The rate of MDR-TB has risen rapidly in Hlabisa, apparently due to both reactivation disease and recent transmission. Many patients were not diagnosed with tuberculosis and many were not suspected of drug-resistant disease, and outcome was poor.

Digitally-implemented naturally sampled PWM suitable for multilevel converter control

For dynamic closed loop control of a multilevel converter with a low pulse number (ratio of switching frequency to synthesized fundamental), natural sampled pulse-width modulation (PWM) is the best form of modulation. Natural sampling does not introduce distortion or a delayed response to the modulating signal. However previous natural sampled PWM implementations have generally been analog. For a modular multilevel converter, a digital implementation has advantages of accuracy and flexibility. Re-sampled uniform PWM is a novel digital modulation technique which approaches the performance of natural PWM. Both hardware and software implementations for a five level multilevel converter phase are presented, demonstrating the improvement over uniform PWM.

Aktiivisen verkkosillan tuottaman yhteismuotoisen jännitteen vaimentaminen kaksitasoisessa, jännitevälipiirillisessä, taajuusmuuttajatopologiassa

Pulssinleveysmoduloidun vaihtosuuntaajan hyötysuhteen parantaminen ja kytkentätaajuuden suurentaminen ovat johtaneet lähtöjännitteen suuritaajuiseen taajuussisältöön kaksitasoisessa, jännitevälipiirillisessä taajuusmuuttajatopologiassa. Kasvava tarve siirtää tehoa myös verkkoon päin on lisännyt aktiivisen verkkosillan käyttöä. Kaksitasoisen aktiivisen verkkosillan vaikutuksesta DC-välipiirin keskipisteen ja kolmivaiheisen kuorman tähtipisteen välinen jännite on nollasta poikkeava aiheuttaen suurentuneen yhteismuotoisen jännitteen taajuusmuuttajan lähtöön ja verkon puolelle. Lisäksi yhteismuotoisten jännitteiden aiheuttamat kytkentätaajuiset häiriövirrat voivat aiheuttaa vikavirtasuojien tahatonta laukeamista, vaikeuttaa EMC-standardien vaatimusten täyttämistä, lisätä moottorin käämieristyksien rasitusta ja mahdollisuutta moottorin laakerivaurioille. Diplomityössä tutkitaan aktiivisen ja passiivisen verkkosillan tuottamaa yhteismuotoista jännitettä simuloinneilla. Esitellään aikaisempaa tutkimustietoa yhteismuotoisen jännitteen ja virran vaimennusratkaisuista aktiivista verkkosiltaa käytettäessä. Tutkimustiedon pohjalta suunnitellaan koelaitteistolle soveltuva suodin. Suotimen toiminta testataan simuloinnein sekä kokeellisin mittauksin. Tehdyt mittaukset osoittavat, että suunniteltu suodin vaimentaa yhteismuotoista jännitettä noin 20 dB verkkosillan kytkentätaajuudella ja tämän jälkeen yli 20 dB/dekadi taajuuteen 100 kHz asti. Lisäksi yhteismuotoisen virran suuruus syöttökaapelin kautta pieneni ehdotetun suotimen vaikutuksesta.

Limittelymenetelmän hyödyntäminen verkkovaihtosuuntaajassa: LCL-suotimen mitoitus

Teollisuudessa yleinen trendi on saada entistä tehokkaampia, halvempia, hyötysuhteeltaan parempia ja fyysisiltä mitoiltaan pienempiä sähkökäyttöjä. Luonnollisesti nämä vaatimukset ovat samoja myös taajuusmuuttajilla. Näiden vaatimusten välillä täytyy aina tehdä kompromisseja ja kehittää uusia menetelmiä. Monissa teollisuuden sähkökäytöissä tarvitaan verkkovaihtosuuntaajaa syöttämään tehoa generaattorilta tai jarrutettavalta moottorilta sähköverkkoon. Verkkovaihtosuuntaajassa käytännössä tarvitaan aina LCL-suodin, joka on fyysisesti järjestelmän suurin ja kallein yksittäinen komponentti, ja luonnollisesti suuritehoinen laite vaatii suuren LCL-suotimen. LCL-Suotimen fyysinen koko on kääntäen verrannollinen kytkentätaajuuteen. Tässä diplomityössä esitellään interleaving eli limittelymenetelmä, jonka avulla pystytään kasvattamaan verkkovaihtosuuntaajan ekvivalenttista kytkentätaajuutta ja pienentämään virran värettä sekä kokonaisharmonista säröä. Menetelmästä aiheutuu myös merkittävä haaste, kiertovirrat, joiden suodatusta tutkitaan kahdella eri menetelmällä. Käytetyt suodatustavat ovat LCL-suodin, jossa on lisäksi CM-kuristin ja LCL-suodin, jossa käytetään solujen välistä muuntajaa, ICT:tä. Työ suoritettiin teoriatutkimuksena ja simuloimalla. Tulokset osoittavat, että molemmat suodatustavat voivat toimia todellisessa sovelluksessa. Kuitenkin vain ICT:n omaava suodin on selkeästi vastaavan kokoista kaksitasoista verkkovaihtosuuntaajan suodinta pienempi. Tutkimus osoittaa myös sen, että tutkitussa sovelluskohteessa pelkkä fyysinen suodin ei riitä suodattamaan kiertovirtoja, vaan säätimeen täytyy tehdä myös muutoksia.

Crystal growth, Raman scattering and optical properties of the superconductor Cd2Re2O7(16O, 18O)/

Using the Physical Vapor Transport method, single crystals of Cd2Re207 have been grown, and crystals of dimensions up to 8x6x2 mm have been achieved. X-ray diffraction from a single crystal of Cd2Re207 has showed the crystal growth in the (111) plane. Powder X-ray diffraction measurements were performed on ^^O and ^^O samples, however no difference was observed. Assigning the space group Fd3m to Cd2Re207 at room temperature and using structure factor analysis, the powder X-ray diffraction pattern of the sample was explained through systematic reflection absences. The temperatiure dependence of the resistivity measurement of ^^O has revealed two structural phase transitions at 120 and 200 K, and the superconducting transition at 1.0 K. Using Factor Group Analysis on three different structiures of Cd2Re207, the number of IR and Raman active phonon modes close to the Brillouin zone centre have been determined and the results have been compared to the temperature-dependence of the Raman shifts of ^^O and ^*0 samples. After scaling (via removing Bose-Einstein and Rayleigh scattering factors from the scattered light) all spectra, each spectrum was fitted with a number of Lorentzian peaks. The temperature-dependence of the FWHM and Raman shift of mode Eg, shows the effects of the two structurjil phase transitions above Tc. The absolute reflectance of Cd2Re207 - '^O single crystals in the far-infrared spectral region (7-700 cm~^) has been measured in the superconducting state (0.5 K), right above the superconducting state (1.5 K), and in the normal state (4.2 K). Thermal reflectance of the sample at 0.5 K and 1.5 K indicates a strong absorption feature close to 10 cm~^ in the superconducting state with a reference temperature of 4.2 K. By means of Kramers-Kronig analysis, the absolute reflectance was used to calculate the optical conductivity and dielectric function. The real part of optical conductivity shows five distinct active phonon modes at 44, 200, 300, 375, and 575 cm~' at all temperatures including a Drude-like behavior at low frequencies. The imaginary part of the calculated dielectric function indicates a mode softening of the mode 44 cm~' below Tc.