Tensile behaviour of a structural adhesive at high temperatures by the extended finite element method

Component joining is typically performed by welding, fastening, or adhesive-bonding. For bonded aerospace applications, adhesives must withstand high-temperatures (200°C or above, depending on the application), which implies their mechanical characterization under identical conditions. The extended finite element method (XFEM) is an enhancement of the finite element method (FEM) that can be used for the strength prediction of bonded structures. This work proposes and validates damage laws for a thin layer of an epoxy adhesive at room temperature (RT), 100, 150, and 200°C using the XFEM. The fracture toughness (G Ic ) and maximum load ( ); in pure tensile loading were defined by testing double-cantilever beam (DCB) and bulk tensile specimens, respectively, which permitted building the damage laws for each temperature. The bulk test results revealed that decreased gradually with the temperature. On the other hand, the value of G Ic of the adhesive, extracted from the DCB data, was shown to be relatively insensitive to temperature up to the glass transition temperature (T g ), while above T g (at 200°C) a great reduction took place. The output of the DCB numerical simulations for the various temperatures showed a good agreement with the experimental results, which validated the obtained data for strength prediction of bonded joints in tension. By the obtained results, the XFEM proved to be an alternative for the accurate strength prediction of bonded structures.

Inspeção e manutenção de torres de radiocomunicações

Relatório de Estágio para obtenção de grau de Mestre em Engenharia Civil Área de Especialização de Edificações

Feasibility of the extended finite element method for the simulation of composite bonded joints

Adhesive-bonding for the unions in multi-component structures is gaining momentum over welding, riveting and fastening. It is vital for the design of bonded structures the availability of accurate damage models, to minimize design costs and time to market. Cohesive Zone Models (CZM’s) have been used for fracture prediction in structures. The eXtended Finite Element Method (XFEM) is a recent improvement of the Finite Element Method (FEM) that relies on traction-separation laws similar to those of CZM’s but it allows the growth of discontinuities within bulk solids along an arbitrary path, by enriching degrees of freedom. This work proposes and validates a damage law to model crack propagation in a thin layer of a structural epoxy adhesive using the XFEM. The fracture toughness in pure mode I (GIc) and tensile cohesive strength (sn0) were defined by Double-Cantilever Beam (DCB) and bulk tensile tests, respectively, which permitted to build the damage law. The XFEM simulations of the DCB tests accurately matched the experimental load-displacement (P-d) curves, which validated the analysis procedure.

Strength improvement of adhesively-bonded joints using a reverse-bent geometry

Adhesive bonding of components has become more efficient in recent years due to the developments in adhesive technology, which has resulted in higher peel and shear strengths, and also in allowable ductility up to failure. As a result, fastening and riveting methods are being progressively replaced by adhesive bonding, allowing a big step towards stronger and lighter unions. However, single-lap bonded joints still generate substantial peel and shear stress concentrations at the overlap edges that can be harmful to the structure, especially when using brittle adhesives that do not allow plasticization in these regions. In this work, a numerical and experimental study is performed to evaluate the feasibility of bending the adherends at the ends of the overlap for the strength improvement of single-lap aluminium joints bonded with a brittle and a ductile adhesive. Different combinations of joint eccentricity were tested, including absence of eccentricity, allowing the optimization of the joint. A Finite Element stress and failure analysis in ABAQUS® was also carried out to provide a better understanding of the bent configuration. Results showed a major advantage of using the proposed modification for the brittle adhesive, but the joints with the ductile adhesive were not much affected by the bending technique.

Effect of hole drilling at the overlap on the strength of single-lap joints

Bonded unions are gaining importance in many fields of manufacturing owing to a significant number of advantages to the traditional fastening, riveting, bolting and welding techniques. Between the available bonding configurations, the single-lap joint is the most commonly used and studied by the scientific community due to its simplicity, although it endures significant bending due to the non-collinear load path, which negatively affects its load bearing capabilities. The use of material or geometric changes in single-lap joints is widely documented in the literature to reduce this handicap, acting by reduction of peel and shear peak stresses at the damage initiation sites in structures or alterations of the failure mechanism emerging from local modifications. In this work, the effect of hole drilling at the overlap on the strength of single-lap joints was analyzed experimentally with two main purposes: (1) to check whether or not the anchorage effect of the adhesive within the holes is more preponderant than the stress concentrations near the holes, arising from the sharp edges, and modification of the joints straining behaviour (strength improvement or reduction, respectively) and (2) picturing a real scenario on which the components to be bonded are modified by some external factor (e.g. retrofitting of decaying/old-fashioned fastened unions). Tests were made with two adhesives (a brittle and a ductile one) varying the adherend thickness and the number, layout and diameter of the holes. Experimental testing showed that the joints strength never increases from the un-modified condition, showing a varying degree of weakening, depending on the selected adhesive and hole drilling configuration.

Adherend thickness effect on the tensile fracture toughness of a structural adhesive using an optical data acquisition method

Adhesive bonding is nowadays a serious candidate to replace methods such as fastening or riveting, because of attractive mechanical properties. As a result, adhesives are being increasingly used in industries such as the automotive, aerospace and construction. Thus, it is highly important to predict the strength of bonded joints to assess the feasibility of joining during the fabrication process of components (e.g. due to complex geometries) or for repairing purposes. This work studies the tensile behaviour of adhesive joints between aluminium adherends considering different values of adherend thickness (h) and the double-cantilever beam (DCB) test. The experimental work consists of the definition of the tensile fracture toughness (GIC) for the different joint configurations. A conventional fracture characterization method was used, together with a J-integral approach, that take into account the plasticity effects occurring in the adhesive layer. An optical measurement method is used for the evaluation of crack tip opening and adherends rotation at the crack tip during the test, supported by a Matlab® sub-routine for the automated extraction of these quantities. As output of this work, a comparative evaluation between bonded systems with different values of adherend thickness is carried out and complete fracture data is provided in tension for the subsequent strength prediction of joints with identical conditions.

Strap repairs using embedded patches: numerical analysis and experimental results

Adhesively bonded repairs offer an attractive option for repair of aluminium structures, compared to more traditional methods such as fastening or welding. The single-strap (SS) and double-strap (DS) repairs are very straightforward to execute but stresses in the adhesive layer peak at the overlap ends. The DS repair requires both sides of the damaged structures to be reachable for repair, which is often not possible. In strap repairs, with the patches bonded at the outer surfaces, some limitations emerge such as the weight, aerodynamics and aesthetics. To minimize these effects, SS and DS repairs with embedded patches were evaluated in this work, such that the patches are flush with the adherends. For this purpose, in this work standard SS and DS repairs, and also with the patches embedded in the adherends, were tested under tension to allow the optimization of some repair variables such as the overlap length (LO) and type of adhesive, thus allowing the maximization of the repair strength. The effect of embedding the patch/patches on the fracture modes and failure loads was compared with finite elements (FE) analysis. The FE analysis was performed in ABAQUS® and cohesive zone modelling was used for the simulation of damage onset and growth in the adhesive layer. The comparison with the test data revealed an accurate prediction for all kinds of joints and provided some principles regarding this technique.

Adhesive thickness effects of a ductile adhesive by optical measurement techniques

Adhesive bonding is an excellent alternative to traditional joining techniques such as welding, mechanical fastening or riveting. However, there are many factors that have to be accounted for during joint design to accurately predict the joint strength. One of these is the adhesive layer thickness (tA). Most of the results are for epoxy structural adhesives, tailored to perform best with small values of tA, and these show that the lap joint strength decreases with increase of tA (the optimum joint strength is usually obtained with tA values between 0.1 and 0.2 mm). Recently, polyurethane adhesives were made available in the market, designed to perform with larger tA values, and whose fracture behaviour is still not studied. In this work, the effect of tA on the tensile fracture toughness (View the MathML source) of a bonded joint is studied, considering a novel high strength and ductile polyurethane adhesive for the automotive industry. This work consists on the fracture characterization of the bond by a conventional and the J-integral techniques, which accurately account for root rotation effects. An optical measurement method is used for the evaluation of crack tip opening (δn) and adherends rotation at the crack tip (θo) during the test, supported by a Matlab® sub-routine for the automated extraction of these parameters. As output of this work, fracture data is provided in traction for the selected adhesive, enabling the subsequent strength prediction of bonded joints.

Estudo e otimização de juntas do tipo Tpeel soldadas, adesivas e híbridas

A necessidade de utilizar métodos de ligação que melhor satisfaçam as necessidades de projeto tem causado a crescente utilização das juntas adesivas, em detrimento dos métodos tradicionais tais como a soldadura, ligações aparafusadas e rebitadas. A sua utilização em diversas aplicações industriais justifica-se pela redução de peso, redução de concentrações de tensões, isolamento acústico e melhor resistência à corrosão. Contudo, também apresentam desvantagens, como a necessidade de preparação das juntas, a fraca resistência a esforços de arrancamento e a complexidade da previsão da sua resistência. As juntas híbridas são obtidas por combinação de uma técnica tradicional com uma ligação adesiva. As juntas híbridas adesivas-soldadas obtêm-se através da combinação da ligação adesiva com a ligação soldada, sendo a soldadura de resistência por pontos a técnica de soldadura mais usada no fabrico deste tipo de juntas. A sinergia entre ligação adesiva e soldadura por pontos oferece vantagens competitivas em relação às ligações adesivas, tais como superior resistência e rigidez, e maior resistência ao arrancamento e à fadiga. No presente trabalho é apresentado um estudo experimental e numérico de juntas T-peel soldadas, adesivas e híbridas (adesivas-soldadas) solicitadas ao arrancamento. Considerouse o adesivo frágil Araldite® AV138 e os adesivos dúcteis Araldite® 2015 e Sikaforce® 7752 e aderentes de aço (C45E). Foi realizada uma análise dos valores experimentais e efetuada uma comparação destes valores com os resultados obtidos pelo Método de Elementos Finitos (MEF) no software ABAQUS®, que incluiu uma análise de tensões na camada de adesivo e previsão do comportamento das juntas por MDC. Observou-se que, dos três adesivos em estudo, o adesivo Sikaforce® 7752 é o que apresenta o melhor desempenho na ligação de juntas T-peel. A boa concordância entre os resultados experimentais e numéricos permitiu validar a utilização de MDC para previsão da resistência de juntas T-peel adesivas e híbridas. Assim, o presente trabalho representa uma base para posterior aplicação no projeto deste tipo de ligação, com as vantagens decorrentes na redução do tempo de projeto e maior facilidade de otimização.

Estudo numérico da adequação de diferentes tipos de leis coesivas na previsão da resistência de juntas adesivas por Modelos de Dano Coesivo

O uso de ligações adesivas aumentou significativamente nos últimos anos e é hoje em dia uma técnica de ligação dominante na indústria aeronáutica e automóvel. As ligações adesivas visam substituir os métodos tradicionais de fixação mecânicos na união de estruturas. A melhoria ao longo dos anos de vários modelos de previsão de dano, nomeadamente através do Método de Elementos Finitos (MEF), tem ajudado ao desenvolvimento desta técnica de ligação. Os Modelos de Dano coesivo (MDC), usados em conjunto com MEF, são uma ferramenta viável para a previsão de resistência de juntas adesivas. Os MDC combinam critérios da resistência dos materiais para a iniciação do dano e conceitos da mecânica da fratura para a propagação da fenda. Existem diversas formas de leis coesivas possíveis de aplicar em simulações por MDC, em função do comportamento expectável dos materiais que estão a ser simulados. Neste trabalho, estudou-se numericamente o efeito de diversas formas de leis coesivas na previsão no comportamento de juntas adesivas, nomeadamente nas curvas forçadeslocamento (P-) de ensaios Double-Cantilever Beam para caracterização à tração e ensaios End-Notched Flexure para caraterização ao corte. Também se estudou a influência dos parâmetros coesivos à tração e corte nas curvas P- dos referidos ensaios. Para o Araldite®AV138 à tração e ao corte, a lei triangular é a que melhor prevê o comportamento do adesivo. Para a previsão da resistência de ambos os adesivos Araldite® 2015 e SikaForce® 7752, a lei trapezoidal é a que melhor se adequa, confirmando assim que esta lei é a que melhor caracteriza o comportamento de dano de adesivos tipicamente dúcteis. O estudo dos parâmetros revelou influência distinta na previsão do comportamento das juntas, embora com bastantes semelhanças entre os diferentes tipos de adesivos.

Empirical models for quantification of machining damage in composite materials

Dissertação para obtenção do Grau de Doutor em Engenharia Mecânica

Preparation with fasting and acipimox increases myocardial glucose uptake in mice during cardiac 18F-FDG microPET

Purpose: Cardiac 18F-FDG PET is considered as the gold standard to assess myocardial metabolism and infarct size. The myocardial demand for glucose can be influenced by fasting and/or following pharmacological preparation. In the rat, it has been previously shown that fasting combined with preconditioning with acipimox, a nicotinic acid derivate and lipidlowering agent, increased dramatically 18F-FDG uptake in the myocardium. Strategies aimed at reducing infarct scar are evaluated in a variety of mouse models. PET would particularly useful for assessing cardiac viability in the mouse. However, prior knowledge of the best preparation protocol is a prerequisite for accurate measurement of glucose uptake in mice. Therefore, we studied the effect of different protocols on 18F-FDG uptake in the mouse heart.Methods: Mice (n = 15) were separated into three treatment groups according to preconditioning and underwent a 18FDG PET scan. Group 1: No preconditioning (n = 3); Group 2: Overnight fasting (n = 8); and Group 3: Overnight fasting and acipimox (25mg/kg SC) (n = 4). MicroPET images were processed with PMOD to determine 18F-FDG mean standard uptake value (SUV) at 30 min for the whole left ventricle (LV) and for each region of the 17-segments AHA model. For comparisons, we used Mann-Whitney test and multilevel mixed-effects linear regression (Stata 11.0).Results: In total, 27 microPET were performed successfully in 15 animals. Overnight fasting led to a dramatic increase in LV-SUV compared to mice without preconditioning (8.6±0.7g/mL vs. 3.7±1.1g/mL, P<0.001). In addition, LV-SUV was slightly but not significantly higher in animals treated with acipimox compared to animals with overnight fasting alone (10.2±0.5 g/mL, P = 0.06). Fastening increased segmental SUV by 5.1±0.5g/mL as compared to free-feeding mice (from 3.7±0.8g/mL to 8.8±0.4g/mL, P<0.001); segmental-SUV also significantly increased after administration of acipimox (from 8.8±0.4g/mL to 10.1±0.4g/mL, P<0.001).Conclusion: Overnight fasting led to myocardial glucose deprivation and increases 18F-FDG myocardial uptake. Additional administration of acipimox enhances myocardial 18F-FDG uptake, at least at the segmental level. Thus, preconditioning with acipimox may provide better image quality that may help for assessing segmental myocardial metabolism.

Calceology : an introduction to North Western European archaeological leather footwear (Neolithic period to c. AD 1600)

Calceology is the study of recovered archaeological leather footwear and is comprised of conservation, documentation and identification of leather shoe components and shoe styles. Recovered leather shoes are complex artefacts that present technical, stylistic and personal information about the culture and people that used them. The current method in calceological research for typology and chronology is by comparison with parallel examples, though its use poses problems by an absence of basic definitions and the lack of a taxonomic hierarchy. The research findings of the primary cutting patterns, used for making all leather footwear, are integrated with the named style method and the Goubitz notation, resulting in a combined methodology as a basis for typological organisation for recovered footwear and a chronology for named shoe styles. The history of calceological research is examined in chapter two and is accompanied by a review of methodological problems as seen in the literature. Through the examination of various documentation and research techniques used during the history of calceological studies, the reasons why a standard typology and methodology failed to develop are investigated. The variety and continual invention of a new research method for each publication of a recovered leather assemblage hindered the development of a single standard methodology. Chapter three covers the initial research with the database through which the primary cutting patterns were identified and the named styles were defined. The chronological span of each named style was established through iterative cross-site sedation and named style comparisons. The technical interpretation of the primary cutting patterns' consistent use is due to constraints imposed by the leather and the forms needed to cover the foot. Basic parts of the shoe patterns and the foot are defined, plus terms provided for identifying the key points for pattern making. Chapter four presents the seventeen primary cutting patterns and their sub-types, these are divided into three main groups: six integral soled patterns, four hybrid soled patterns and seven separately soled patterns. Descriptions of the letter codes, pattern layout, construction principle, closing seam placement and list of sub-types are included in the descriptions of each primary cutting pattern. The named shoe styles and their relative chronology are presented in chapter five. Nomenclature for the named styles is based on the find location of the first published example plus the primary cutting pattern code letter. The named styles are presented in chronological order from Prehistory through to the late 16th century. Short descriptions of the named styles are given and illustrated with examples of recovered archaeological leather footwear, reconstructions of archaeological shoes and iconographical sources. Chapter six presents documentation of recovered archaeological leather using the Goubitz notation, an inventory and description of style elements and fastening methods used for defining named shoe styles, technical information about sole/upper constructions and the consequences created by the use of lasts and sewing forms for style identification and fastening placement in relation to the instep point. The chapter concludes with further technical information about the implications for researchers about shoemaking, pattern making and reconstructive archaeology. The conclusion restates the original research question of why a group of primary cutting patterns appear to have been used consistently throughout the European archaeological record. The quantitative and qualitative results from the database show the use of these patterns but it is the properties of the leather that imposes the use of the primary cutting patterns. The combined methodology of primary pattern identification, named style and artefact registration provides a framework for calceological research.

A support system for evaluating a suitable joining method in the production of sheet metal goods

This report illustrates a comparative study of various joining methods involved in sheet metal production. In this report it shows the selection of joining methods, which includes comparing the advantages and disadvantages of a method over the other ones and choosing the best method for joining. On the basis of various joining process from references, a table is generated containing set of criterion that helps in evaluation of various sheet metal joining processes and in selecting the most suitable process for a particular product. Three products are selected and a comprehensive study of the joining methods is analyzed with the help of various parameters. The table thus is the main part of the analysis process of this study and can be advanced with the beneficial results. It helps in a better and easy understanding and comparing the various methods, which provides the foundation of this study and analysis. The suitability of the joining method for various types of cases of different sheet metal products can be tested with the help of this table. The sections of the created table display the requirements of manufacturing. The important factor has been considered and given focus in the table, as how the usage of these parameters is important in percentages according to particular or individual case. The analysis of the methods can be extended or altered by changing the parameters according to the constraint. The use of this table is demonstrated by pertaining the cases from sheet metal production.

Tuulivoimalan generaattorin roottorin valmistuksen ja valmistuskustannusten arviointi

Diplomityössä on käsitelty tuulivoimalan generaattorin roottorin valmistusta ja magneettien kiinnitystä. Työ on osa projektia, jonka tarkoituksena on ollut tuottaa kohdeyritykselle vaihtoehtoinen tuulivoimalan generaattorin roottorirakenne. Työhön on koottu projektissa käsitellyt asiat roottorin valmistustekniikan osalta. Työssä on selvitetty kustannuksien kannalta paras vaihtoehto roottorin valmistamiseksi sisältäen kuljetukset ja magneettien kokoonpanon. Valmistusmenetelminä on vertailtu hitsausta ja valamista. Magneettien osalta tarkasteltiin uuden vaihtoehtoisen kiinnitysmenetelmän tuomia säästöjä nykyiseen ratkaisuun verrattuna. Uusien roottorien kustannuksia on verrattu nykyiseen rakenteeseen. Tutkimusmenetelminä on käytetty projektiryhmän palavereja, haastatteluja ja kirjallisuusselvityksiä. Lopputuloksena kohdeyritykselle luotiin uusi roottorikonsepti, jossa yhdistyvät edullisempi roottorin valmistus ja magneettien kiinnitys. Roottorin valmistaminen valamalla osoittautui selvästi edullisemmaksi kuin hitsaaminen levyistä. Magneettien kiinnitystä yksinkertaistettiin käyttämällä seostettuja magneetteja ja magneettikehyksiä. Roottorin konstruktiomuutoksien avulla mahdollistettiin suurempi magneettien määrä, joka mahdollistaa suuremman tehontuoton.