Period Continuous Tuning of an Efficient Mid-Infrared Optical Parametric Oscillator Based on a Fan-out Periodically Poled MgO-Doped Lithium Niobate

We report a period continuously tunable, efficient, mid-infrared optical parametric oscillator (OPO) based on a fan-out periodically poled MgO-doped congruent lithium niobate (PPMgLN). The OPO is pumped by a Nd:YAG laser and a maximum idler output average power of 1.65 W at 3.93 mu m is obtained with a pump average power of 10.5 W, corresponding to the conversion efficiency of about 16% from the pump to the idler. The output spectral properties of the OPO with the fan-out crystal are analyzed. The OPO is continuously tuned over 3.78-4.58 mu m (idler) when fan-out periods are changed from 27.0 to 29.4 mu m. Compared with temperature tuning, fan-out period continuous tuning has faster tuning rate and wider tuning range.

NOR network transduction procedures : "merging of gates" and "substitution of gates" for fan-in and fan-out restricted networks, NETTRA-G3-FIFO and NETTRA-PG1-FIFO /

"December 1974."--T.p.

NOR (NAND) network design : error-compensation procedures for fan-in and fan-out restricted networks (NETTRA-E1-FIFO and NETTRA-E2-FIFO /

Thesis (M. S.)--University of Illinois at Urbana-Champaign.

Network transduction programs based on connectable and disconnectable conditions with fan-in and fan-out restrictions : (a description of NETTRA-G1-FIFO and NETTRA-G2-FIFO) /

Includes bibliographical references.

The design of NOR networks under fan-in and fan-out const[r]aints : a programming manual for FIFOTRAN-G1 /

"Report No. UIUCDCS-R-74-661"

Directional solidification of aluminum-nickel eutectic alloys using electroslag remelting

Attempts were made to produce directionally solidified, specifically grain aligned Al-6 wt pct Ni eutectic alloy using a laboratory scale ESR unit. For this purpose sand cast alloy electrodes were electroslag remelted under different mold conditions. The grain structure of the ingots obtained from these meltings showed that insulated silica molds gave the best vertical alignment of grains along the length of the ingot. The NiAl3 fibers within the grains tended to fan out and there was only a preferred alignment of fibers along the growth direction under the conditions of our experiments. The ESR parameters most suitable for vertical alignment of eutectic grains have been identified. In some electroslag remelting trials ingots were grown on a seed ingot. This resulted in a fewer vertical grains compared to the case when no seed ingot was used. The sand cast specimen of the eutectic exhibited a maximum tensile strength of around 88.2 MN/m2 (9.0 kg/mm2) whereas conventional ESR using water cooled mold gave strength value of 98.0 MN/m2 (10 kg/mm2). The directionally solidified ESR material showed longitudinal tensile strength as high as 213.7 MN/m2 (21.8 kg/mm2) which could be further increased to 220.6 MN/m2 (22.5 kg/mm2) by using the seed ingot. The average growth rate was varied between 5 to 25 mm/min during electroslag remelting in this study. The flow stresses, tangent modulus and ultimate tensile strength of directionally solidified eutectic increased with increasing growth rates.

0.84 ps Resolution Clock Skew Measurement via Subsampling

An all-digital on-chip clock skew measurement system via subsampling is presented. The clock nodes are sub-sampled with a near-frequency asynchronous sampling clock to result in beat signals which are themselves skewed in the same proportion but on a larger time scale. The beat signals are then suitably masked to extract only the skews of the rising edges of the clock signals. We propose a histogram of the arithmetic difference of the beat signals which decouples the relationship of clock jitter to the minimum measurable skew, and allows skews arbitrarily close to zero to be measured with a precision limited largely by measurement time, unlike the conventional XOR based histogram approach. We also analytically show that the proposed approach leads to an unbiased estimate of skew. The measured results from a 65 nm delay measurement front-end indicate that for an input skew range of +/- 1 fan-out-of-4 (FO4) delay, +/- 3 sigma resolution of 0.84 ps can be obtained with an integral error of 0.65 ps. We also experimentally demonstrate that a frequency modulation on a sampling clock maintains precision, indicating the robustness of the technique to jitter. We also show how FM modulation helps in restoring precision in case of rationally related clocks.

Acoustic response of vortex breakdown modes in a coaxial isothermal unconfined swirling jet

The present experimental work is concerned with the study of amplitude dependent acoustic response of an isothermal coaxial swirling jet. The excitation amplitude is increased in five distinct steps at the burner's Helmholtz resonator mode (i.e., 100 Hz). Two flow states are compared, namely, sub-critical and super-critical vortex breakdown (VB) that occur before and after the critical conical sheet breakdown, respectively. The geometric swirl number is varied in the range 2.14-4.03. Under the influence of external pulsing, global response characteristics are studied based on the topological changes observed in time-averaged 2D flow field. These are obtained from high resolution 2D PIV (particle image velocimetry) in the longitudinal-mid plane. PIV results also illustrate the changes in the normalized vortex core coordinates (r(vcc)/(r(vcc))(0) (Hz), y(vcc)/(y(vcc))(0) (Hz)) of internal recirculation zone (IRZ). A strong forced response is observed at 100 Hz (excitation frequency) in the convectively unstable region which get amplified based on the magnitude of external forcing. The radial extent of this forced response region at a given excitation amplitude is represented by the acoustic response region (b). The topological placement of the responsive convectively unstable region is a function of both the intensity of imparted swirl (characterized by swirl number) and forcing amplitude. It is observed that for sub-critical VB mode, an increase in the excitation amplitude till a critical value shifts the vortex core centre (particularly, the vortex core moves downstream and radially outwards) leading to drastic fanning-out/widening of the IRZ. This is accompanied by similar to 30% reduction in the recirculation velocity of the IRZ. It is also observed that b < R (R: radial distance from central axis to outer shear layer-OSL). At super-critical amplitudes, the sub-critical IRZ topology transits back (the vortex core retracts upstream and radially inwards) and finally undergoes a transverse shrinkage ((r(vcc))/(r(vcc))(0 Hz) decreases by similar to 20%) when b >= R. In contrast, the vortex core of super-critical breakdown mode consistently spreads radially outwards and is displaced further downstream. Finally, the IRZ fans-out at the threshold excitation amplitude. However, the acoustic response region b is still less than R. This is explained based on the characteristic geometric swirl number (S-G) of the flow regimes. The super-critical flow mode with higher S-G (hence, higher radial pressure drop due to rotational effect which scales as Delta P similar to rho u theta(2) and acts inwards towards the center line) compared to sub-critical state imposes a greater resistance to the radial outward spread of b. As a result, the acoustic energy supplied to the super-critical flow mode increases the degree of acoustic response at the pulsing frequency and energizes its harmonics (evident from power spectra). As a disturbance amplifier, the stronger convective instability mode within the flow structure of super-critical VB causes the topology to widen/fan-out severely at threshold excitation amplitude. (C) 2015 AIP Publishing LLC.

Ivory Victorian Day Planner

The planner has an ivory cover and 6 celluloid pages which fan out. The days of the week were stamped on each page, except Sunday. In this case, the days of the week are faded away and someone has rewritten them and included Sunday on the back cover. The front cover has a metal escutcheon engraved with the letter C and it closes with a metal latch. The front ivory cover is cracked down the middle and the front page is also cracked. R. Band has written on the “Monday” page that this belonged to Dr. Cleveland, this note is dated June 6, 2004. The “Tuesday” page has the title “Julia’s house” and gives the numbers of doors, lights, windows and water closets etc. within the house. On the back of the “Friday” page is the number 4784 and on the back of the Saturday page is the name and address of Dr. Mafarlan [?] of Pennsylvania.

Paper dimensional stability in sheet-fed offset printing : Papperets dimensionsstabilitet i en arkoffsetpress

In offset printing, dampening solution is used to create a good balance in the process. If too much water is transferred to the paper, the sheet can change its size between the printing units, due to water absorption, and cause a problem with the colour register. This phenomenon is usually referred to as fanout. In this degree project, an investigation was made to see if the paper dimensions changed through its way in the sheet-fed printing process. The instrument Luchs Register Measuring Systems (Lynx) was used, and a method for measuring if the paper changed its dimensions with this instrument, was developed. Paper qualities with three different grammages were used, 90, 130 and 250 gsm. This investigation showed that all paper qualities changed their size with widening in the gripper edge in the range of 10 - 70 µm and in the trailing edge the increase was 10 - 130 µm. The elongations of the papers were in the range of 10- 300 µm. The papers with lowest grammage changed more than the heavier. To see if the print had been affected of the widening and elongation, print quality parameters like relative contrast, dot gain and mottle were correlated with the Lynx data from the sheets. The group of papers that gave correlations were in 130 gsm. The sheets had visual doubling and the combined standard deviation from the Lynx marks K3, K5 and K21 correlated with dot gain. When the variations increased so did the dot gain and this indicates that the doubling was due to the widening. There was also a correlation between the standard deviation from K3 and Mottle. The sheets widened with an average of 30 µm in the gripper edge and since there probably were doubling due to widening it also affected the Mottle values. What the widening depends on is hard to tell. Since widening was so small, it could be due to water absorption, papers being ironed out or maybe the sheets have been flattened out. It probably needs a more detailed investigation to find out what causes the widening. Further investigations about how print quality is affected by the register accuracy of a printing machine should include a print form with measuring areas close to the Lynx marks. The measuring areas should contain fine hairlines, negative text printed with at least two colours and some pictures to evaluate together with standard measuring should give a good knowledge about the subject.

Identificando interesses transversais em modelos de requisitos PL-AOVgraph

The occurrence of problems related to the scattering and tangling phenomenon, such as the difficulty to do system maintenance, increasingly frequent. One way to solve this problem is related to the crosscutting concerns identification. To maximize its benefits, the identification must be performed from early stages of development process, but some works have reported that this has not been done in most of cases, making the system development susceptible to the errors incidence and prone to the refactoring later. This situation affects directly to the quality and cost of the system. PL-AOVgraph is a goal-oriented requirements modeling language which offers support to the relationships representation among requirements and provides separation of crosscutting concerns by crosscutting relationships representation. Therefore, this work presents a semi-automatic method to crosscutting concern identification in requirements specifications written in PL-AOVgraph. An adjacency matrix is used to identify the contributions relationships among the elements. The crosscutting concern identification is based in fan-out analysis of contribution relationships from the informations of adjacency matrix. When identified, the crosscutting relationships are created. And also, this method is implemented as a new module of ReqSys-MDD tool

Neural Processing Unit based on the Optical Bistable Properties of Semiconductor Laser Amplifiers

This paper analyzes the behavior of a neural processing unit based on the optical bistable properties of semiconductor laser amplifiers. A similar unit to the reported here was previously employed in the simulation of the mammalian retina. The main advantages of the present cell are its larger fan-out and the possibility of different responses according to the light wavelength impinging onto the cell. These properties allow to work with larger structures as well as to obtain different behaviors according to the light characteristics. This new approach gives a possible modeling closer to the real biological configurations. Moreover, a more detailed analysis of the basic cell internal behavior is reported

Fan activism on Twitter: online sport fandom communities and the campaign #ForaRicardoTeixeira [Fã-ativismo no Twitter: comunidades online de fãs de esporte e a campanha #ForaRicardoTeixeira]

This paper approaches a particular type of fandom practice, what I am calling fan activism. Fan activism is a topic that has historically received little attention in the fandom studies area. Here, I analyse the #ForaRicardoTeixeira campaign from a sample of 15,000 tweets posted at the time of his re¬signation from CBF. This paper combines quantitative and qualitative methods to investigate a) the com¬munity dynamics and b) the content of the conversations. The dynamics analysis pointed out, for instance, patterns of users and information sources, and the content analysis revealed how users framed the case. Future implications of the results for the study of online sport fandom practices are discussed at last.

The art of being a fan : complicity and criticality in contemporary art and fandom

This practice-led research project aims to use contemporary art processes and concepts of fandom to construct a space for the critical and creative exploration of the relationship between them. Much of the discourse addressing the intersection of these spaces over the last three decades tends to treat art and fan studies as separate areas of critical and theoretical research. There has also been very little consideration of the critical interface that art practice and fandom share in their engagement with one another – or how the artist as fan might creatively exploit this relationship. Approaching these issues through a practice-led methodology that combines studio based explorations and traditional modes of research, the project aims to demonstrate how my 'fannish' engagements with popular culture can generate new responses to, and understandings of, the relationship between fandom, affect and visual art. The research acts as a performative and creative investigation of fandom as I document the complicit tendencies that arise out of my affective relationship with pop cultural artefacts. It does this through appropriating and reconfiguring content from film, television and print media, to create digital video installations aimed at engendering new experiences and critical interpretations of screen culture. This approach promotes new possibilities for creative engagements with art and popular culture, and these are framed through the lens of what I term the digital-bricoleur. The research will be primarily contextualised by examining other artists' practices as well as selected theoretical frameworks that traverse my investigative terrain. The key artists that are discussed include Douglas Gordon, Candice Brietz, Pierre Huyghe, Paul Pfieffer, and Jennifer and Kevin McCoy. The theoretical developments of the project are drawn from a pluralistic range of ideas ranging from Johanna Drucker's discussion of critical complicity in contemporary art, Matt Hills' discussion of subjectivity in fandom and academia, Nicolas Bourriaud's discussion of Postproduction art practices, and Jacques Rancière's ideas about aesthetics and politics. The methodology and artworks developed over the course of this project will also demonstrate how digital-bricolage leads to new understandings of the relationships between contemporary art and entertainment. The research aims to exploit these apparently contradictory positions to generate a productive site for rethinking the relationship between the creative and critical possibilities of art and fandom. The outcomes of the research consists of a body of artworks – 75% – that demonstrate new contributions to knowledge, and an exegetical component – 25% – that acts to reflect on, analyse and critically contextualise the practice-led findings.

Detached-eddy simulation of transonic flow past a fan-blade section

Detached-eddy simulation of transonic flow past a thin section of a fan blade has been carried out. The inflow Mach number is 1.03, and a bow shock forms upstream of the blade. The shock (corresponding to an adjacent blade) impinges on the suction-side boundary layer which causes separation and rapid transition to turbulence. The boundary layer later re-attaches near the trailing edge. The pressure-side boundary layer transitions near the leading edge and remains attached. Mean surface pressure shows basic agreement with a steady RANS calculation; strong shock motion in the DES is the major cause of discrepancy. Surface pressure spectra are investigated, and low-frequency two-dimensional disturbances associated with the shock motion are dominant. Removing the two-dimensional component from the spectra, the pressure-side three-dimensional spectra reproduce the spectral shape given by a correlation for flat-plate boundary layer wall-pressure spectra developed by Goody. 1 The suction-side disturbances produce similar high- and intermediate-frequency scalings despite substantially different boundary layer development. Near-wake results show that disturbance kinetic energy peaks at the suction-side inflection point of the mean profile, and that the energy is concentrated at low frequencies relative to the near-trailing edge surface pressure. Copyright © 2009 by the authors.