Desenvolvimento teórico e experimental de FSS com elementos fractais de Gosper em estruturas de multicamadas

The fractal self-similarity property is studied to develop frequency selective surfaces (FSS) with several rejection bands. Particularly, Gosper fractal curves are used to define the shapes of the FSS elements. Due to the difficulty of making the FSS element details, the analysis is developed for elements with up to three fractal levels. The simulation was carried out using Ansoft Designer software. For results validation, several FSS prototypes with fractal elements were fabricated. In the fabrication process, fractals elements were designed using computer aided design (CAD) tools. The prototypes were measured using a network analyzer (N3250A model, Agilent Technologies). Matlab software was used to generate compare measured and simulated results. The use of fractal elements in the FSS structures showed that the use of high fractal levels can reduce the size of the elements, at the same time as decreases the bandwidth. We also investigated the effect produced by cascading FSS structures. The considered cascaded structures are composed of two FSSs separated by a dielectric layer, which distance is varied to determine the effect produced on the bandwidth of the coupled geometry. Particularly, two FSS structures were coupled through dielectric layers of air and fiberglass. For comparison of results, we designed, fabricated and measured several prototypes of FSS on isolated and coupled structures. Agreement was observed between simulated and measured results. It was also observed that the use of cascaded FSS structures increases the FSSs bandwidths and, in particular cases, the number of resonant frequencies, in the considered frequency range. In future works, we will investigate the effects of using different types of fractal elements, in isolated, multilayer and coupled FSS structures for applications on planar filters, high-gain microstrip antennas and microwave absorbers

Polarisation independent bandpass FSS

The spectral transmittance of a frequency selective surface (FSS), which consists of two free-standing arrays of short-circuited nested annular slots, is presented. The FSS was designed to provide a minimum of 20 dB isolation between the frequency bands 316.5-325.5 and 349.5-358.5 GHz when the filter operates in the TE and TM planes at 45 degrees incidence. Experimental results, which are in close agreement with the computed transmission coefficients, show that the maximum insertion loss is 0.9 dB, and the minimum cross-polar discrimination is at least 21 dB in the passbands. The FSS yields virtually identical spectral responses in the two polarisation planes over the frequency range 315-359 GHz.

Single sideband FSS with high image rejection

The design of a quasi-optical single sideband filter, which provides more than 30 dB of isolation between the frequency bands 294-305.5 and 329.5-341.5 GHz in the TM plane at 45 degrees incidence, is described. The structure, which consists of three free-standing arrays of dipole slot elements, generates a bandpass spectral response with an insertion loss below 0.5 dB at resonance. Simulated and measured transmission coefficients in the range 250-400 GHz are shown to be in good agreement.

Two-layer mm-wave FSS of linear slot elements with low insertion loss

The performance of a very low loss frequency selective surface (FSS) comprising two air spaced planar arrays of linear slot elements is reported. The beamsplitter generates a low loss passband response with a very sharp transmission roll-off with frequency. Simulated and measured results in the 30 GHz and 300 GHz wavebands are used to quantify the performance improvement compared to a conventional multilayer dielectrically backed conducting ring FSS. The paper also discusses the effect of the array dimensions on the passband width and filter roll-off rate.

Characterisation of microwave phase conjugate signal generation using nonlinearly loaded wire frequency selective surface (FSS)

Both experimental and theoretical information regarding the scattering and phase conjugate mixing properties of a 2D double-periodic array of wires loaded with nonlinear/linear lumped elements have been provided. An experimental means for assessing the phase conjugate energy production capability for the array is given. These investigations enable identification of the fundamental operational characteristics and underlying mechanisms associated with the production of phase conjugate energy by this type of artificial electromagnetic media. Means for enhancing the phase conjugate energy production capability of the structure by using additional linear lumped loads is examined theoretically and limits on the production of phase conjugate energy established. Theoretical far-field prediction of the behaviour of the structure indicates that retro-directive reflector action as well as negative refraction should be possible.

A Modified Pole-Zero Technique for the Synthesis of Waveguide Leaky-Wave Antennas Loaded With Dipole-Based FSS

An extension of the pole-zero matching method proposed by Stefano Maci et al. for the analysis of electromagnetic bandgap (EBG) structures composed by lossless dipole-based frequency selective surfaces (FSS) printed on stratified dielectric media, is presented in this paper. With this novel expansion, the dipoles length appears as a variable in the analytical dispersion equation. Thus, modal dispersion curves as a function of the dipoles length can be easily obtained with the only restriction of single Floquet mode propagation. These geometry-dispersion curves are essential for the efficient analysis and design of practical EBG structures, such as waveguides loaded with artificial magnetic conductors (AMC) for miniaturization, or leaky-wave antennas (LWA) using partially reflective surfaces (PRS). These two practical examples are examined in this paper. Results are compared with full-wave 2D and 3D simulations showing excellent agreement, thus validating the proposed technique and illustrating its utility for practical designs.

325GHz Single Layer Sub-Millimeter Wave FSS Based Split Ring Linear to Circular Polarisation Convertor

A single layer, frequency selective surface based, sub-millimeter wave transmission polarizer is presented that converts incident slant linear 45° polarization into circular polarization upon transmission. The polarization convertor consists of a 30 mm diameter 10 thick silicon reinforced metalized screen containing 2700 resonator cells and perforated with nested split ring slot apertures. The screen was designed and optimized using CST Microwave Studio and predictions were validated experimentally by transmission measurements over the 250-365 GHz frequency range. This frequency range is used for remote environmental monitoring and 325 GHz represents a molecular emission line for H2O. The results obtained show good agreement between measured and modeled predictions. The measured 3 dB axial ratio bandwidth was 11.75%, measured minimum Axial Ratio was 0.19 dB and the measured insertion loss of the single layer screen was 3.38 dB