Estimating Local Part Thickness in Midplane Meshes for Finite Element Analysis

Within the development of motor vehicles, crash safety (e.g. occupant protection, pedestrian protection, low speed damageability), is one of the most important attributes. In order to be able to fulfill the increased requirements in the framework of shorter cycle times and rising pressure to reduce costs, car manufacturers keep intensifying the use of virtual development tools such as those in the domain of Computer Aided Engineering (CAE). For crash simulations, the explicit finite element method (FEM) is applied. The accuracy of the simulation process is highly dependent on the accuracy of the simulation model, including the midplane mesh. One of the roughest approximations typically made is the actual part thickness which, in reality, can vary locally. However, almost always a constant thickness value is defined throughout the entire part due to complexity reasons. On the other hand, for precise fracture analysis within FEM, the correct thickness consideration is one key enabler. Thus, availability of per element thickness information, which does not exist explicitly in the FEM model, can significantly contribute to an improved crash simulation quality, especially regarding fracture prediction. Even though the thickness is not explicitly available from the FEM model, it can be inferred from the original CAD geometric model through geometric calculations. This paper proposes and compares two thickness estimation algorithms based on ray tracing and nearest neighbour 3D range searches. A systematic quantitative analysis of the accuracy of both algorithms is presented, as well as a thorough identification of particular geometric arrangements under which their accuracy can be compared. These results enable the identification of each technique’s weaknesses and hint towards a new, integrated, approach to the problem that linearly combines the estimates produced by each algorithm.

Application of a model updating technique for health condition monitoring and damage detection of flexible structures

This paper discusses the application of a damage detection methodology to monitor the location and extent of partial structural damage. The methodology combines, in an iterative way, the model updating technique based on frequency response functions (FRF) with monitoring data aiming at identifying the damage area of the structure. After the updating procedure reaches a good correlation between the models, it compares the parameters of the damage structure with those of the undamaged one to find the deteriorated area. The influence of the FEM mesh size on the evaluation of the extent of the damage has also been discussed. The methodology is applied using real experimental data from a spatial frame structure.

Simulación eficiente de mecanismos flexibles mediante formulaciones topológicas

El objetivo de esta Tesis es presentar un método eficiente para la evaluación de sistemas multi-cuerpo con elementos flexibles con pequeñas deformaciones, basado en métodos topológicos para la simulación de sistemas tan complejos como los que se utilizan en la práctica y en tiempo real o próximo al real. Se ha puesto un especial énfasis en la resolución eficiente de aquellos aspectos que conllevan mayor coste computacional, tales como la evaluación de las ecuaciones dinámicas y el cálculo de los términos de inercia. Las ecuaciones dinámicas se establecen en función de las variables independientes del sistema, y la integración de las mismas se realiza mediante formulaciones implícitas de index-3. Esta Tesis se articula en seis Capítulos. En el Capítulo 1 se realiza una revisión bibliográfica de la simulación de sistemas flexibles y los métodos más relevantes de integración de las ecuaciones diferenciales del movimiento. Asimismo, se presentan los objetivos de esta Tesis. En el Capítulo 2 se presenta un método semi-recursivo para la evaluación de las ecuaciones de los sistemas multi-cuerpo con elementos flexibles basado en formulaciones topológicas y síntesis modal. Esta Tesis determina la posición de cada punto del cuerpo flexible en función de un sistema de referencia flotante que se mueve con dicho cuerpo y de las amplitudes de ciertos modos de deformación calculados a partir de un mallado obtenido mediante el Método de Elementos Finitos. Se presta especial atención en las condiciones de contorno que se han de tener en cuenta a la hora de establecer las variables que definen la deformación del cuerpo flexible. El Capítulo 3 se centra en la evaluación de los términos de inercia de los sistemas flexibles que generalmente conllevan un alto coste computacional. Se presenta un método que permite el cálculo de dichos términos basado en el uso de 24 matrices constantes que pueden ser calculadas previamente al proceso de integración. Estas matrices permiten evaluar la matriz de masas y el vector de fuerzas de inercia dependientes de la velocidad sin que sea necesario evaluar la posición deformada de todos los puntos del cuerpo flexible. Se realiza un análisis pormenorizado de dichas matrices con el objetivo de optimizar su cálculo estableciendo aproximaciones que permitan reducir el número de dichos términos y optimizar aún más su evaluación. Se analizan dos posibles simplificaciones: la primera utiliza una discretización no-consistente basada en elementos finitos en los que se definen únicamente los desplazamientos axiales de los nodos; en la segunda propuesta se hace uso de una matriz de masas concentradas (Lumped Mass). Basándose en la formulación presentada, el Capítulo 4 aborda la integración eficiente de las ecuaciones dinámicas. Se presenta un método iterativo para la integración con fórmulas de index-3 basado en la proyección de las ecuaciones dinámicas según las variables independientes del sistema multi-cuerpo. El cálculo del residuo del sistema de ecuaciones no lineales que se ha de resolver de modo iterativo se realiza mediante un proceso recursivo muy eficiente que aprovecha la estructura topológica del sistema. Se analizan tres formas de evaluar la matriz tangente del citado sistema no lineal: evaluación aproximada, numérica y recursiva. El método de integración presentado permite el uso de distintas fórmulas. En esta Tesis se analizan la Regla Trapezoidal, la fórmula BDF de segundo orden y un método híbrido TR-BDF2. Para este último caso se presenta un algoritmo de paso variable. En el Capítulo 5 plantea la implementación del método propuesto en un programa general de simulación de mecanismos que permita la resolución de cualquier sistema multi-cuerpo definiéndolo mediante un fichero de datos. La implementación de este programa se ha realizado tanto en C++ como en Java. Se muestran los resultados de las formulaciones presentadas en esta Tesis mediante la simulación de cuatro ejemplos de distinta complejidad. Mediante análisis concretos se comparan la formulación presentada con otras existentes. También se analiza el efecto del lenguaje de programación utilizado en la implementación y los efectos de las posibles simplificaciones planteadas. Por último, el Capítulo 6 resume las principales conclusiones alcanzadas en la Tesis y las futuras líneas de investigación que con ella se abren. ABSTRACT This Thesis presents an efficient method for solving the forward dynamics of a multi-body sys-tem formed by rigid and flexible bodies with small strains for real-time simulation of real-life models. It is based on topological formulations. The presented work focuses on the efficient solution of the most time-consuming tasks of the simulation process, such as the numerical integration of the motion differential equations and in particular the evaluation of the inertia terms corresponding to the flexible bodies. The dynamic equations are formulated in terms of independent variables of the muti-body system, and they are integrated by means of implicit index-3 formulae. The Thesis is arranged in six chapters. Chapter 1 presents a review of the most relevant and recent contributions related to the modelization of flexible multi-body systems and the integration of the corresponding dynamic equations. The main objectives of the Thesis are also presented in detail. Chapter 2 presents a semi-recursive method for solving the equations of a multi-body system with flexible bodies based on topological formulations and modal synthesis. This Thesis uses the floating frame approach and the modal amplitudes to define the position of any point at the flexible body. These modal deformed shapes are obtained by means of the Finite Element Method. Particular attention has been taken to the boundary conditions used to define the deformation of the flexible bodies. Chapter 3 focuses on the evaluation of the inertia terms, which is usually a very time-consuming task. A new method based on the use of 24 constant matrices is presented. These matrices are evaluated during the set-up step, before the integration process. They allow the calculation of the inertia terms in terms of the position and orientation of the local coordinate system and the deformation variables, and there is no need to evaluate the position and velocities of all the nodes of the FEM mesh. A deep analysis of the inertia terms is performed in order to optimize the evaluation process, reducing both the terms used and the number of arithmetic operations. Two possible simplifications are presented: the first one uses a non-consistent approach in order to define the inertia terms respect to the Cartesian coordinates of the FEM mesh, rejecting those corresponding to the angular rotations; the second approach makes use of lumped mass matrices. Based on the previously presented formulation, Chapter 4 is focused on the numerical integration of the motion differential equations. A new predictor-corrector method based on index-3 formulae and on the use of multi-body independent variables is presented. The evaluation of the dynamic equations in a new time step needs the solution of a set on nonlinear equations by a Newton-Raphson iterative process. The computation of the corresponding residual vector is performed efficiently by taking advantage of the system’s topological structure. Three methods to compute the tangent matrix are presented: an approximated evaluation that considers only the most relevant terms, a numerical approach based on finite differences and a recursive method that uses the topological structure. The method presented for integrating the dynamic equations can use a variety of integration formulae. This Thesis analyses the use of the trapezoidal rule, the 2nd order BDF formula and the hybrid TR-BDF2 method. A variable-time step strategy is presented for the last one. Chapter 5 describes the implementation of the proposed method in a general purpose pro-gram for solving any multibody defined by a data file. This program is implemented both in C++ and Java. Four examples are used to check the validity of the formulation and to compare this method with other methods commonly used to solve the dynamic equations of multi-body systems containing flexible bodies. The efficiency of the programming methodology used and the effect of the possible simplifications proposed are also analyzed. Chapter 6 summarizes the main Conclusions obtained in this Thesis and the new lines of research that have been opened.

Integrating open source codes for solid modeling and automatic mesh generation in FEM applications

The applications of the Finite Element Method (FEM) for three-dimensional domains are already well documented in the framework of Computational Electromagnetics. However, despite the power and reliability of this technique for solving partial differential equations, there are only a few examples of open source codes available and dedicated to the solid modeling and automatic constrained tetrahedralization, which are the most time consuming steps in a typical three-dimensional FEM simulation. Besides, these open source codes are usually developed separately by distinct software teams, and even under conflicting specifications. In this paper, we describe an experiment of open source code integration for solid modeling and automatic mesh generation. The integration strategy and techniques are discussed, and examples and performance results are given, specially for complicated and irregular volumes which are not simply connected. © 2011 IEEE.

A simple way to introduce fibers into FEM models

This communication proposes a simple way to introduce fibers into finite element modelling. This is a promising formulation to deal with fiber-reinforced composites by the finite element method (FEM), as it allows the consideration of short or long fibers placed arbitrarily inside a continuum domain (matrix). The most important feature of the formulation is that no additional degree of freedom is introduced into the pre-existent finite element numerical system to consider any distribution of fiber inclusions. In other words, the size of the system of equations used to solve a non-reinforced medium is the same as the one used to solve the reinforced counterpart. Another important characteristic is the reduced work required by the user to introduce fibers, avoiding `rebar` elements, node-by-node geometrical definitions or even complex mesh generation. An additional characteristic of the technique is the possibility of representing unbounded stresses at the end of fibers using a finite number of degrees of freedom. Further studies are required for non-linear applications in which localization may occur. Along the text the linear formulation is presented and the bounded connection between fibers and continuum is considered. Four examples are presented, including non-linear analysis, to validate and show the capabilities of the formulation. Copyright (c) 2007 John Wiley & Sons, Ltd.

Simulation and material calibration of ultra high strength steel (UHSS) S960 welded joint under static tensile test utilizing finite element method (FEM)

The aim of this work was to calibrate the material properties including strength and strain values for different material zones of ultra-high strength steel (UHSS) welded joints under monotonic static loading. The UHSS is heat sensitive and softens by heat due to welding, the affected zone is heat affected zone (HAZ). In this regard, cylindrical specimens were cut out from welded joints of Strenx® 960 MC and Strenx® Tube 960 MH, were examined by tensile test. The hardness values of specimens’ cross section were measured. Using correlations between hardness and strength, initial material properties were obtained. The same size specimen with different zones of material same as real specimen were created and defined in finite element method (FEM) software with commercial brand Abaqus 6.14-1. The loading and boundary conditions were defined considering tensile test values. Using initial material properties made of hardness-strength correlations (true stress-strain values) as Abaqus main input, FEM is utilized to simulate the tensile test process. By comparing FEM Abaqus results with measured results of tensile test, initial material properties will be revised and reused as software input to be fully calibrated in such a way that FEM results and tensile test results deviate minimum. Two type of different S960 were used including 960 MC plates, and structural hollow section 960 MH X-joint. The joint is welded by BöhlerTM X96 filler material. In welded joints, typically the following zones appear: Weld (WEL), Heat affected zone (HAZ) coarse grained (HCG) and fine grained (HFG), annealed zone, and base material (BaM). Results showed that: The HAZ zone is softened due to heat input while welding. For all the specimens, the softened zone’s strength is decreased and makes it a weakest zone where fracture happens while loading. Stress concentration of a notched specimen can represent the properties of notched zone. The load-displacement diagram from FEM modeling matches with the experiments by the calibrated material properties by compromising two correlations of hardness and strength.

Three-dimensional modeling and highly refined mesh generation of the aorta artery and its tunics

This paper describes strategies and techniques to perform modeling and automatic mesh generation of the aorta artery and its tunics (adventitia, media and intima walls), using open source codes. The models were constructed in the Blender package and Python scripts were used to export the data necessary for the mesh generation in TetGen. The strategies proposed are able to provide meshes of complicated and irregular volumes, with a large number of mesh elements involved (12,000,000 tetrahedrons approximately). These meshes can be used to perform computational simulations by Finite Element Method (FEM). © Published under licence by IOP Publishing Ltd.

Modeling of a Heat-Induced Buckling of Plates Using the Mesh-free Method

In the process of engineering design of structural shapes, the flat plate analysis results can be generalized to predict behaviors of complete structural shapes. In this case, the purpose of this project is to analyze a thin flat plate under conductive heat transfer and to simulate the temperature distribution, thermal stresses, total displacements, and buckling deformations. The current approach in these cases has been using the Finite Element Method (FEM), whose basis is the construction of a conforming mesh. In contrast, this project uses the mesh-free Scan Solve Method. This method eliminates the meshing limitation using a non-conforming mesh. I implemented this modeling process developing numerical algorithms and software tools to model thermally induced buckling. In addition, convergence analysis was achieved, and the results were compared with FEM. In conclusion, the results demonstrate that the method gives similar solutions to FEM in quality, but it is computationally less time consuming.

The optical analysis of the abdominal wall using the biospeckle after implants of polypropylene mesh in rats

PURPOSE: To evaluate an experimental animal model to study the abdominal tissue activity considering its interaction with a polypropylene mesh, through the use of one of the optical phenomena of light Laser, the biospeckle. METHODS: Fifty Wistar male rats were divided into four groups: Group 1: ten animals not submitted to surgery; Group 2: ten animals submitted to surgery without polypropylene mesh; Group 3: 20 animals submitted to surgery followed by the mesh placement; Group 4: (sham) with ten animals. None of the animals presented post surgical complications being submitted to the optical tests at the 20th postoperative day. RESULTS: The analysis from the biospeckle tests, comparing the medians and standard deviations with T Student test, indicated that no significative difference was observed on the abdominal wall tissue activity in the four groups considered, with and without polypropylene mesh prosthesis implantation. CONCLUSION: The animal model is viable and the biospeckle open ways for a great number of experiments to be developed in evaluating tissue activity.

Two dimensional analysis of inflatable structures by the positional FEM

This paper presents a, simple two dimensional frame formulation to deal with structures undergoing large motions due to dynamic actions including very thin inflatable structures, balloons. The proposed methodology is based on the minimum potential energy theorem written regarding nodal positions. Velocity, acceleration and strain are achieved directly from positions, not. displacements, characterizing the novelty of the proposed technique. A non-dimensional space is created and the deformation function (change of configuration) is written following two independent mappings from which the strain energy function is written. The classical New-mark equations are used to integrate time. Dumping and non-conservative forces are introduced into the mechanical system by a rheonomic energy function. The final formulation has the advantage of being simple and easy to teach, when compared to classical Counterparts. The behavior of a bench-mark problem (spin-up maneuver) is solved to prove the formulation regarding high circumferential speed applications. Other examples are dedicated to inflatable and very thin structures, in order to test the formulation for further analysis of three dimensional balloons.

A positional FEM Formulation for geometrical non-linear analysis of shells

This work presents a fully non-linear finite element formulation for shell analysis comprising linear strain variation along the thickness of the shell and geometrically exact description for curved triangular elements. The developed formulation assumes positions and generalized unconstrained vectors as the variables of the problem, not displacements and finite rotations. The full 3D Saint-Venant-Kirchhoff constitutive relation is adopted and, to avoid locking, the rate of thickness variation enhancement is introduced. As a consequence, the second Piola-Kirchhoff stress tensor and the Green strain measure are employed to derive the specific strain energy potential. Curved triangular elements with cubic approximation are adopted using simple notation. Selected numerical simulations illustrate and confirm the objectivity, accuracy, path independence and applicability of the proposed technique.

Use of Medical Subject Headings (MeSH) in Portuguese for categorizing web-based healthcare content

Introduction: Internet users are increasingly using the worldwide web to search for information relating to their health. This situation makes it necessary to create specialized tools capable of supporting users in their searches. Objective: To apply and compare strategies that were developed to investigate the use of the Portuguese version of Medical Subject Headings (MeSH) for constructing an automated classifier for Brazilian Portuguese-language web-based content within or outside of the field of healthcare, focusing on the lay public. Methods: 3658 Brazilian web pages were used to train the classifier and 606 Brazilian web pages were used to validate it. The strategies proposed were constructed using content-based vector methods for text classification, such that Naive Bayes was used for the task of classifying vector patterns with characteristics obtained through the proposed strategies. Results: A strategy named InDeCS was developed specifically to adapt MeSH for the problem that was put forward. This approach achieved better accuracy for this pattern classification task (0.94 sensitivity, specificity and area under the ROC curve). Conclusions: Because of the significant results achieved by InDeCS, this tool has been successfully applied to the Brazilian healthcare search portal known as Busca Saude. Furthermore, it could be shown that MeSH presents important results when used for the task of classifying web-based content focusing on the lay public. It was also possible to show from this study that MeSH was able to map out mutable non-deterministic characteristics of the web. (c) 2010 Elsevier Inc. All rights reserved.

Phase fraction distribution measurement of oil-water flow using a capacitance wire-mesh sensor

In this paper, a novel wire-mesh sensor based on permittivity (capacitance) measurements is applied to generate images of the phase fraction distribution and investigate the flow of viscous oil and water in a horizontal pipe. Phase fraction values were calculated from the raw data delivered by the wire-mesh sensor using different mixture permittivity models. Furthermore, these data were validated against quick-closing valve measurements. Investigated flow patterns were dispersion of oil in water (Do/w) and dispersion of oil in water and water in oil (Do/w&w/o). The Maxwell-Garnett mixing model is better suited for Dw/o and the logarithmic model for Do/w&w/o flow pattern. Images of the time-averaged cross-sectional oil fraction distribution along with axial slice images were used to visualize and disclose some details of the flow.

Alternative positional FEM applied to thermomechanical impact of truss structures

This paper presents a formulation to deal with dynamic thermomechanical problems by the finite element method. The proposed methodology is based on the minimum potential energy theorem written regarding nodal positions, not displacements, to solve the mechanical problem. The thermal problem is solved by a regular finite element method. Such formulation has the advantage of being simple and accurate. As a solution strategy, it has been used as a natural split of the thermomechanical problem, usually called isothermal split or isothermal staggered algorithm. Usual internal variables and the additive decomposition of the strain tensor have been adopted to model the plastic behavior. Four examples are presented to show the applicability of the technique. The results are compared with other authors` numerical solutions and experimental results. (C) 2010 Elsevier B.V. All rights reserved.