Extracts from pitanga (Eugenia uniflora L.) leaves: Influence of extraction process on antioxidant properties and yield of phenolic compounds

Different extraction processes were employed to extract the polyphenolic compounds from pitanga (Eugenia uniflora L) leaves: a one-step process using water, ethanol or supercritical CO(2) as solvents, and a two-step process using supercritical CO(2) followed by either water or ethanol. The total polyphenolic compounds, total flavonoids and antioxidant activity were determined in all the extracts obtained. The process performance was evaluated with respect to three variables: global extraction yield, concentration and yield of both polyphenols and flavonoids in the extracts. For the one-step extraction, the results showed that the extraction yield increased with solvent polarity. For the two-step process, the results suggested that water was more efficient in extracting the phenolic compounds from E. uniflora when the matrix was previously extracted with scCO(2). With respect to the antioxidant activity, the ethanolic extracts obtained from both processes, using either the DPPH radical scavenging method or the beta-carotene bleaching method, presented high antioxidant activities. (C) 2010 Elsevier B.V. All rights reserved.

Effects of the extraction conditions on the yield and composition of rice bran oil extracted with ethanol-A response surface approach

Rice bran oil was obtained from rice bran by solvent extraction using ethanol. The influence of process variables, solvent hydration (0-24% of water, on mass basis), temperature (60-90 degrees C), solvent-to-rice bran mass ratio (2.5:1 to 4.5:1) and stirrer speed (100-250 rpm) were analysed using the response surface methodology. The extraction yield was highly affected by the solvent water content, and it varied from 8.56 to 20.05 g of oil/100 g of fresh rice bran (or 42.7-99.9% of the total oil available) depending on the experimental conditions. It was observed that oryzanol and tocols behave in different ways during the extraction process. A larger amount of tocols is extracted from the solid matrix in relation to gamma-oryzanol. It was possible to obtain values from 123 to 271 mg of tocols/kg of fresh rice bran and 1527 to 4164 mg of oryzanol/kg of fresh rice bran, indicating that it is feasible to obtain enriched oil when this renewable solvent is used. No differences in the chemical composition of the extracted oils were observed when compared to the data cited in the literature. (C) 2011 The Institution of Chemical Engineers. Published by Elsevier B.V. All rights reserved.

Extraction behavior of Mo and W as homologs of Sg with α-benzoinoxime

Solvent extraction of molybdenum and tungsten as homologues of Sg with a-benzoinoxime from HCl solutions has been investigated. The extraction equilibration was achieved at 20s for Mo and W. Molybdenum was almost quantitatively extracted from 0.001 to 4M HCl solutions, and the extraction yields decreased at higher and lower acid concentrations due to the formation of anionic oxychloride complex and anionic species MO42-, respectively. The extraction yield of W was lower than that of Mo during the whole range of acid concentration. The composition of the extracted species was determined by using the slope method in present experiment. The elemental analysis, IR and 1H NMR spectra of the extracted species suggest that the extracted complex contain one MoO22+or WO22+ groups bonded with two a-benzoinoxime molecules.

Extraction and purification of triterpenic acids from eucalypt bark

A indústria da pasta e do papel é um sector importante da economia mundial, particularmente a que assenta em espécies de Eucalyptus. No entanto, essas indústrias geram quantidades significativas de correntes secundárias de subprodutos e resíduos de biomassa que podem ser exploradas em aplicações de valor acrescentado em vez de serem queimadas para produção de energia. Um exemplo nobre pode ser a produção de ácidos triterpénicos com estruturas dos tipos lupano, oleanano e ursano, dada a sua abundância em alguns destes resíduos, em particular na casca, adotando o conceito de biorrefinaria integrada numa fábrica de pasta. Estes compostos são conhecidos pelas suas inúmeras actividades biológicas, por exemplo, antioxidante, anti-inflamatória e antitumoral, e podem encontrar aplicações em produtos de elevado valor, tais como cosméticos, nutracêuticos ou farmacêuticos. Neste sentido, o estudo das potencialidades das cascas das espécies de eucalipto mais exploradas enquanto fontes de compostos triterpénicos é um tópico relevante. Por conseguinte, foram analisados e comparados em pormenor os teores e composições em ácidos triterpénicos (TTAs) das cascas externas de várias espécies de eucalipto (E. globulus, E. grandis, E. urograndis, E. maidenii e E. nitens). Os teores dos principais TTAs identificados nestas espécies variaram entre 4.5 g/kg no E. urograndis e 21.6 g/kg no E. nitens. Observou-se que as cascas externas de Eucalyptus de zonas temperadas e Mediterrânicas, nomeadamente E. nitens e E. globulus, são mais ricas em TTAs que as espécies de regiões tropicais e subtropicais. Além disso, a casca externa do E. globulus é claramente a mais rica em ácidos com estruturas do tipo ursano enquanto a do E. nitens é a mais rica em ácidos do tipo oleanano e lupano. Estes resultados levaram-nos a estudar a extração dos TTAs da casca de Eucalyptus, bem como a sua posterior concentração e purificação, a qual foi efetuada por extração sólido-líquido convencional combinada com a precipitação de solutos, e por extração com fluidos supercríticos (SFE). No que diz respeito à primeira abordagem referida, foi desenvolvido neste trabalho um método patenteado que permite obter extratos enriquecidos em TTAs das cascas de eucalipto baseado em tecnologias disponíveis no imediato. Em relação à segunda abordagem, e de forma a apostar em processos de baixo impacto ambiental exigidos pelas biorrefinarias do futuro, a SFE surge como uma opção natural. Assim, foi efetuada a SFE da casca caduca do E. globulus com dióxido de carbono puro e modificado para recuperar a fração de TTAs, e os resultados foram comparados com os obtidos por extração em Soxhlet com diclorometano. Foram realizados estudos preliminares sobre a influência da pressão (100-200 bar), a adição de co-solvente (0, 5 e 8% m/m de etanol), e operação em múltiplos passos a fim de avaliar a aplicabilidade da alternativa supercrítica para a sua produção eficiente e selectiva. Os resultados destacaram a influência da pressão e o importante papel resumo (cont.) desempenhado pelo co-solvente neste processo, cujo efeito foi mais relevante do que o aumento da pressão em várias dezenas de bar. Este trabalho foi depois otimizado, usando o planeamento factorial de experiências e a metodologia de superfícies de resposta, para analisar a influência da temperatura (40-60 ºC), pressão (100-200 bar), e teor de etanol (0.0-5.0% m/m) na recuperação dos TTAs e respectiva concentração nos extractos. Nestes intervalos, as melhores condições de operação encontradas foram 200 bar, 40 °C e 5% de etanol, para as quais os modelos de regressão estatisticamente validados previram um rendimento de extração de 1.2% com 50% de concentração em TTAs, correspondendo ao rendimento em TTAs de 5.1 g/kg de casca e uma recuperação de 79.2% comparativamente ao valor do Soxhlet. Os TTAs livres e acetilados apresentaram tendências de extracção bastante distintas devido às suas diferentes afinidades para o CO2 causadas pelas diferentes polaridades: os derivados acetilados aproximam-se de um patamar máximo a cerca de 200 bar e 5% de etanol, enquanto a extração dos TTAs livres apresenta uma tendência sempre crescente no intervalo de condições estudado. Foram também medidas curvas cumulativas de SFE da casca do E. globulus de forma a analisar o comportamento cinético do processo em termos de rendimento total, rendimento em TTAs, rendimento em TTAs livres, rendimento em TTAs acetilados, e concentração dos TTAs nos extractos. Foi analisada a influência da pressão, temperatura, teor de co-solvente e caudal do dióxido de carbono sobre as respostas anteriores. Os dados experimentais foram modelados com os modelos Logístico, de Dessorção, de Placa Plana Simples, e de Difusão. Na globalidade, os resultados confirmaram que a pressão e o teor de etanol têm um efeito significativo sobre as curvas de extração, os rendimentos finais e as concentrações dos extratos, e mostraram a presença de limitações externas à transferência de massa em alguns ensaios. Mais uma vez, as famílias individuais de TTAs livres e acetilados apresentaram diferentes tendências de extracção. A modelação permitiu-nos confirmar não só o importante papel desempenhado pela difusão intraparticular na SFE, mas também a contribuição da resistência no filme em alguns ensaios. Após a análise de todos os resultados, foi efetuado um ensaio em duas etapas em série, possibilitando o enriquecimento do teor em TTAs no extracto devido às diferentes condições adotadas em cada etapa. Por último, um éster metílico de um ácido triterpénico do tipo oleanano - morolato de metilo - foi identificado pela primeira vez enquanto componente da casca de Eucalyptus na casca externa do Eucalyptus grandis x globulus, onde ocorre em teores elevados. A sua extração com CO2 supercrítico foi também realizada, visando a conceção de uma alternativa de extração ambientalmente benigna para este composto. A 200 bar e 60 ºC, a remoção do morolato de metilo atingiu um patamar às 6 h para 5.1 kg h-1 de CO2 / kg de casca. Em geral, e de forma semelhante à SFE da casca do E. globulus, os TTAs acetilados foram mais significativamente extraídos quando comparados com os seus ácidos livres, o que está diretamente relacionado com a natureza menos polar destas moléculas. O trabalho apresentado nesta tese é uma contribuição para a valorização de uma corrente de biomassa com baixo valor na indústria de pasta em duas vertentes complementares. Por um lado, aumentou o conhecimento da composição lipofílica das cascas de Eucalyptus spp. com interesse comercial para a produção de pasta, destacando o seu potencial enquanto fontes de ácidos triterpénicos. Por outro lado, foram desenvolvidos dois processos alternativos e facilmente integráveis numa fábrica de pasta para a sua exploração a partir da casca: um baseado em tecnologias convencionais bem estabelecidas a nível industrial, prevendo a sua aplicação a curto prazo, e um outro baseado na SFE, seguindo as tendências das futuras biorrefinarias.

Supercritical carbon dioxide extraction of bioactive compounds from microalgae and volatile oils from aromatic plants

A discussion of the most interesting results obtained in our laboratories, during the supercritical CO(2) extraction of bioactive compounds from microalgae and volatile oils from aromatic plants, was carried out. Concerning the microalgae, the studies on Botryococcus braunii and Chlorella vulgaris were selected. Hydrocarbons from the first microalgae, which are mainly linear alkadienes (C(23)-C(31)) with an odd number of carbon atoms, were selectively extracted at 313 K increasing the pressure up to 30.0 MPa. These hydrocarbons are easily extracted at this pressure, since they are located outside the cellular walls. The extraction of carotenoids, mainly canthaxanthin and astaxanthin, from C. vulgaris is more difficult. The extraction yield of these components at 313 K and 35.0 MPa increased with the degree of crushing of the microalga, since they are not extracellular. On the other hand, for the extraction of volatile oils from aromatic plants, studies on Mentha pulegium and Satureja montana L were chosen. For the first aromatic plant, the composition of the volatile and essential oils was similar, the main components being the pulegone and menthone. However, this volatile oil contained small amounts of waxes, which content decreased with decreasing particle size of the plant matrix. For S. montana L it was also observed that both oils have a similar composition, the main components being carvacrol and thymol. The main difference is the relative amount of thymoquinone, which content can be 15 times higher in volatile oil. This oxygenated monoterpene has important biological activities. Moreover, experimental studies on anticholinesterase activity of supercritical extracts of S. montana were also carried out. The supercritical nonvolatile fraction, which presented the highest content of the protocatechuic, vanilic, chlorogenic and (+)-catechin acids, is the most promising inhibitor of the enzyme butyrylcholinesterase. In contrast, the Soxhlet acetone extract did not affect the activity of this enzyme at the concentrations tested. (C) 2011 Elsevier B.V. All rights reserved.

Supercritical CO(2) extraction of carotenoids from pitanga fruits (Eugenia uniflora L.)

Supercritical carbon dioxide (SC-CO(2)) extraction was employed to extract carotenoids from the freeze-dried pulp of pitanga fruits (Eugenia uniflora L.), an exotic fruit, rich in carotenoids and still little explored commercially. The SC-CO(2) extraction was carried out at two temperatures, 40 and 60 degrees C, and seven pressures, 100, 150, 200, 250, 300, 350 and 400 bar. The carotenoids were determined by high-performance liquid chromatography connected to photodiode array and mass spectrometry detectors. Lycopene, rubixanthin and P-cryptoxanthin were the main carotenoids present in the freeze-dried pitanga pulp, whereas beta-cryptoxanthin concentration was negligible in the SC-CO(2) extracts, for all the investigated state conditions. The maximum recovery of carotenoids was obtained at 60 degrees C and 250 bar, extracting 55% of the total carotenoid content, 74% of the rubixanthin and 78% of the lycopene from the pulp. Under these state conditions, the total carotenoid concentration in the extract was 5474 mu g/g, represented by 66% lycopene and 32% rubixanthin. The experimental state conditions produced different SC-CO(2) extracts with respect to the extraction yield and concentration of different carotenoids, indicating that the supercritical carbon dioxide was selective in the extraction of the pitanga carotenoids as a function of temperature and pressure. (C) 2008 Elsevier B.V. All rights reserved.

Thermodynamic and statistical analysis of soybean oil extraction process using renewable solvent

The main goal of this work was to evaluate thermodynamic parameters of the soybean oil extraction process using ethanol as solvent. The experimental treatments were as follows: aqueous solvents with water contents varying from 0 to 13% (mass basis) and extraction temperature varying from 50 to 100 degrees C. The distribution coefficients of oil at equilibrium have been used to calculate enthalpy, entropy and free energy changes. The results indicate that oil extraction process with ethanol is feasible and spontaneous, mainly under higher temperature. Also, the influence of water level in the solvent and temperature were analysed using the response surface methodology (RSM). It can be noted that the extraction yield was highly affected by both independent variables. A joint analysis of thermodynamic and RSM indicates the optimal level of solvent hydration and temperature to perform the extraction process.

A mass transfer model applied to the supercritical extraction with CO2 of curcumins from turmeric rhizomes (Curcuma longa L)

ABSTRACT: Increasing restrictions on the use of artificial pigments in the food industry, imposed by the international market, have increased the importance of raw materials containing natural pigments. Of those natural substances with potential applications turmeric rhizomes (Curcuma longa L), are one of the most important natural sources of yellow coloring. Three different pigments (curcumin, desmetoxycurcumin, and bis-desmetoxycurcumin) constitute the curcuminoids. These pigments are largely used in the food industry as substitutes for synthetic dyes like tartrazin. Extraction of curcuminoids from tumeric rhizomes with supercritical CO2 can be applied as an alternative method to obtain curcuminoids, as natural pigments are in general unstable, and hence degrade when submitted to extraction with organic solvents at high temperatures. Extraction experiments were carried out in a supercritical extraction pilot plant at pressures between 25 and 30 MPa and a temperature of 318 K. The influence of drying pretreatment on extraction yield was evaluated by analyzing the mass transfer kinetics and the content of curcuminoids in the extracts during the course of extraction. The chemical identification of curcuminoids in both the extract and the residual solid was performed by spectrophotometry. Mass transfer within the solid matrix was described by a linear first-order desorption model, while that in the gas phase was described by a convective mass transfer model. Experimental results showed that the concentration profile for curcuminoids during the supercritical extraction process was higher when the turmeric rhizomes were submitted to a drying pretreatment at 343 K.

Supercritical CO2 extraction of phenolic compounds from Baccharis dracunculifolia

Extracts from Baccharis dracunculifolia leaves were obtained using the following solvents: supercritical carbon dioxide (SC-CO2), ethanol and methanol. Supercritical extraction was carried out at temperatures of 40, 50 and 60 degrees C and pressures of 20, 30 and 40 MPa. Four phenolic compounds were analysed in the extracts by high-performance liquid chromatography: 3,5-diprenyl-4-hydroxycinnamic acid (DHCA or artepillin C); 3-prenyl-4-hydroxycinnamic acid (PHCA); 4-hydroxycinnamic acid (p-coumaric acid) and 4-methoxy-3,5,7-trihydroxyflavone (kaempferide). The global extraction yields (X-0) obtained by the conventional methods with ethanol and methanol were higher than those obtained by SC-CO2. However on analysing the components of interest extracted at 60 degrees C and 40 MPa, the extraction yields of kaempferide, DHCA and PHCA were 156%, 98% and 64% higher, respectively, than in the ethanolic extracts. Only the p-coumaric acid extraction yield was better when extracted using the conventional method. (C) 2008 Elsevier B.V. All rights reserved.

Ultrasound and microwave assisted extraction of ergosterol from Agaricus bisporus L.: optimization through response surface methodology

There is scientific evidence demonstrating the benefits of mushrooms ingestion due to their richness in bioactive compounds such as mycosterols, in particular ergosterol [I]. Agaricus bisporus L. is the most consumed mushroom worldwide presenting 90% of ergosterol in its sterol fraction [2]. Thus, it is an interesting matrix to obtain ergosterol, a molecule with a high commercial value. According to literature, ergosterol concentration can vary between 3 to 9 mg per g of dried mushroom. Nowadays, traditional methods such as maceration and Soxhlet extraction are being replaced by emerging methodologies such as ultrasound (UAE) and microwave assisted extraction (MAE) in order to decrease the used solvent amount, extraction time and, of course, increasing the extraction yield [2]. In the present work, A. bisporus was extracted varying several parameters relevant to UAE and MAE: UAE: solvent type (hexane and ethanol), ultrasound amplitude (50 - 100 %) and sonication time (5 min-15 min); MAE: solvent was fixed as ethanol, time (0-20 min), temperature (60-210 •c) and solid-liquid ratio (1-20 g!L). Moreover, in order to decrease the process complexity, the pertinence to apply a saponification step was evaluated. Response surface methodology was applied to generate mathematical models which allow maximizing and optimizing the response variables that influence the extraction of ergosterol. Concerning the UAE, ethanol proved to be the best solvent to achieve higher levels of ergosterol (671.5 ± 0.5 mg/100 g dw, at 75% amplitude for 15 min), once hexane was only able to extract 152.2 ± 0.2 mg/100 g dw, in the same conditions. Nevertheless, the hexane extract showed higher purity (11%) when compared with the ethanol counterpart ( 4% ). Furthermore, in the case of the ethanolic extract, the saponification step increased its purity to 21%, while for the hexane extract the purity was similar; in fact, hexane presents higher selectivity for the lipophilic compounds comparatively with ethanol. Regarding the MAE technique, the results showed that the optimal conditions (19 ± 3 min, 133 ± 12 •c and 1.6 ± 0.5 g!L) allowed higher ergosterol extraction levels (556 ± 26 mg/100 g dw). The values obtained with MAE are close to the ones obtained with conventional Soxhlet extraction (676 ± 3 mg/100 g dw) and UAE. Overall, UAE and MAE proved to he efficient technologies to maximize ergosterol extraction yields.

Flowers of Gomphrena globosa L. as an alternatve source of betacyanins: optimization of the extraction using response surface methodology

Betacyanins are betalain pigments that display a red-violet colour which have been reported to be three times stronger than the red-violet dye produced by anthocyanins [1]. The applications of betacyanins cover a wide range of matrices, mainly as additives or ingredients in the food industry, cosmetics, pharmaceuticals and livestock feed. Although, being less commonly used than anthocyanins and carotenoids, betacyanins are stable between pH 3 to 7 and suitable for colouring in low acid matrices. In addition, betacyanins have been reported to display interesting medicinal character as powerful antioxidant and chemopreventive compounds either in vitro or in vivo models [2]. Betacyanins are obtained mainly from the red beet of Beta vulgaris plant (between I 0 to 20 mg per I 00 g pulp) but alternative primary sources are needed [3]. In addition, independently of the source used, the effect of the variables that affect the extraction of betacyanins have not been properly described and quantified. Therefore, the aim of this study was to identifY and optimize the conditions that maximize betacyanins extraction using the tepals of Gomphrena globosa L. flowers as an alternative source. Assisted by the statistical technique of response surface methodology, an experimental design was developed for testing the significant explanatory variables of the extraction (time, temperature, solid-liquid ratio and ethanolwater ratio). The identification was performed using high-performance liquid chromatography coupled with a photodiode array detector and mass spectrometry with electron spray ionization (HPLC-PDAMS/ ESI) and the response was measured by the quantification of these compounds using HPLC-PDA. Afterwards, a response surface analysis was performed to evaluate the results. The major betacyanin compounds identified were gomphrenin 11 and Ill and isogomphrenin IJ and Ill. The highest total betacyanins content was obtained by using the following conditions: 45 min of extraction. time, 35•c, 35 g/L of solid-liquid ratio and 25% of ethanol. These values would not be found without optimizing the conditions of the betacyanins extraction, which moreover showed contrary trends to what it has been described in the scientific bibliography. More specifically, concerning the time and temperature variables, an increase of both values (from the common ones used in the bibliography) showed a considerable improvement on the betacyanins extraction yield without displaying any type of degradation patterns.

A micro-extraction technique using a new digitally controlled syringe combined with UHPLC for assessment of urinary biomarkers of oxidatively damaged DNA

The formation of reactive oxygen species (ROS) within cells causes damage to biomolecules, including membrane lipids, DNA, proteins and sugars. An important type of oxidative damage is DNA base hydroxylation which leads to the formation of 8-oxo-7,8-dihydro-29-deoxyguanosine (8-oxodG) and 5-hydroxymethyluracil (5-HMUra). Measurement of these biomarkers in urine is challenging, due to the low levels of the analytes and the matrix complexity. In order to simultaneously quantify 8-oxodG and 5-HMUra in human urine, a new, reliable and powerful strategy was optimised and validated. It is based on a semi-automatic microextraction by packed sorbent (MEPS) technique, using a new digitally controlled syringe (eVolH), to enhance the extraction efficiency of the target metabolites, followed by a fast and sensitive ultrahigh pressure liquid chromatography (UHPLC). The optimal methodological conditions involve loading of 250 mL urine sample (1:10 dilution) through a C8 sorbent in a MEPS syringe placed in the semi-automatic eVolH syringe followed by elution using 90 mL of 20% methanol in 0.01% formic acid solution. The obtained extract is directly analysed in the UHPLC system using a binary mobile phase composed of aqueous 0.1% formic acid and methanol in the isocratic elution mode (3.5 min total analysis time). The method was validated in terms of selectivity, linearity, limit of detection (LOD), limit of quantification (LOQ), extraction yield, accuracy, precision and matrix effect. Satisfactory results were obtained in terms of linearity (r2 . 0.991) within the established concentration range. The LOD varied from 0.00005 to 0.04 mg mL21 and the LOQ from 0.00023 to 0.13 mg mL21. The extraction yields were between 80.1 and 82.2 %, while inter-day precision (n=3 days) varied between 4.9 and 7.7 % and intra-day precision between 1.0 and 8.3 %. This approach presents as main advantages the ability to easily collect and store urine samples for further processing and the high sensitivity, reproducibility, and robustness of eVolHMEPS combined with UHPLC analysis, thus retrieving a fast and reliable assessment of oxidatively damaged DNA.

Extracção supercrítica de óleo de grainha de uva combinada com pré-tratamentos enzimáticos

Neste trabalho estudou-se a extracção supercrítica do óleo de grainha de uva, usando dióxido de carbono, e combinou-se este processo com um prétratamento enzimático da semente para aumentar o rendimento global da extracção. A qualidade dos extractos obtidos foi avaliada pelo seu conteúdo em triacilglicerídeos, perfil de ácidos gordos e capacidade antioxidante. Realizaram-se também alguns estudos exploratórios sobre a aplicação de um pré-tratamento de alta pressão (HPP) à grainha da uva. Adicionalmente, efectuou-se o estudo da extracção, fraccionamento e caracterização estrutural das procianidinas da grainha da uva, bem como a avaliação da sua capacidade antioxidante. A extracção de procianidinas da grainha da uva foi efectuada sequencialmente com metanol e acetona/água, tendo sido posteriormente fraccionadas por adição sucessiva de misturas metanol/clorofórmio progressivamente mais concentradas em clorofórmio. A caracterização das procianidinas foi feita por HPLC-UV e LC–MS, antes e depois de sujeitar as amostras a uma tiólise, e também por ESI-MS e ESI-MS/MS. Este estudo permitiu reportar, pela primeira vez, a ocorrência de procianidinas do tipo-A galoiladas na grainha da uva. Os resultados de HPLC-UV permitiram determinar o grau médio de polimerização das procianidinas e a sua composição monomérica em (+)- catequina, (-)-epicatequina e (-)-epicatequina-O-galato. Mostrou-se que a (+)- catequina é o flavan-3-ol terminal mais abundante e a (-)-epicatequina predomina largamente como unidade de extensão. No caso de procianidinas do tipo A, a ligação interflavânica C2-C7 encontra-se essencialmente nas unidades terminais. O grau médio de polimerização das diversas fracções varia entre 1.0 e 10.8. A sua capacidade antioxidante, medida pelo método espectrofotométrico de DPPH•, mostrou-se ser equivalente à de uma amostra comercial de (+)-catequina usada como referência. A partir dos graus médios de polimerização experimentais e das análises de FTIR das fracções correspondentes foi possível obter um modelo preditivo O-PLS com apenas uma variável latente. O pré-tratamento enzimático justificou-se pelo conhecimento existente acerca do uso de enzimas específicas que destroem parcialmente as paredes celulares. Atendendo à composição das paredes celulares da grainha da uva preparou-se uma suspensão contendo protease, xilanase, pectinase e celulase. Para determinar as condições experimentais do pré-tratamento que maximizam o rendimento da extracção, estudou-se o efeito do tempo de reacção, temperatura, pH, diâmetro médio das partículas de grainha moída e a concentração das enzimas. Os incrementos do rendimento da extracção de óleo observados atingiram 163.2%. O estudo da extracção supercrítica (SFE) do óleo da grainha de uva tratada e não-tratada permitiu obter as curvas de extracção correspondentes, bem com analisar a influência das condições operatórias sobre o seu andamento. Montou-se uma instalação laboratorial onde se realizaram experiências com dióxido de carbono a 160, 180, 200 e 220 bar e temperaturas de 313.15 e 323.15 K. Os rendimentos obtidos por SFE foram semelhantes aos de Soxhlet com n-hexano. As curvas de extracção medidas compreendem um primeiro período de extracção, onde se remove cerca de 92-97% do óleo disponível, e um segundo período, essencialmente difusional, com pouco impacto no rendimento final. Os vários extractos recolhidos e o óleo global obtido foram caracterizados para avaliar a sua qualidade e relacioná-la com as condições operatórias de SFE. Determinaram-se o conteúdo total em triacilglicerídeos, o seu perfil de ácidos gordos e a capacidade antioxidante (AOC). Os resultados mostraram que a AOC aumenta com a elevação da pressão e, acentuadamente, com o acréscimo da temperatura. Ao longo da curva de extracção, a AOC é mais pronunciada nos extractos iniciais, nomeadamente nos primeiros 30 a 40% da extracção. A modelação efectuada considerou que o óleo extractável se reparte entre células rompidas, predominantes na periferia da semente, e células intactas, mais interiores. Admitiu-se que o transporte de massa ocorre em série, i.e. das células intactas para as rompidas e destas para o solvente; mostrou-se que a dispersão axial era desprezável. Os balanços materiais à fase fluida e aos volumes de células rompidas e intactas, combinados com os fluxos interno, externo e a relação de equilíbrio foram resolvidos numericamente pelo método das linhas combinado com diferenças finitas atrasadas. O modelo reproduziu bem as curvas experimentais e permitiu simular curvas de eluição e os três perfis de concentração no leito.

Development of new technologies for the selective removal of volatile compounds with applications in forensic science and natural aromas

Tese de doutoramento, Farmácia (Química Farmacêutica e Terapêutica), Universidade de Lisboa, Faculdade de Farmácia, 2015