Catalytic ethanolysis of soybean oil with immobilized lipase from Candida antarctica and (1)H NMR and GC quantification of the ethyl esters (biodiesel) produced

The catalytic ethanolysis of soybean oil with commercial immobilized lipase type B from Candida antarctica to yield ethyl esters (biodiesel) has been investigated. Transesterification was monitored with respect to the following parameters: quantity of biocatalyst, reaction time, amount of water added and turnover of lipase. The highest yields of biodiesel (87% by (1)H NMR; 82.9% by GC) were obtained after a reaction time of 24 h at 32 degrees C in the presence of lipase equivalent to 5.0% (w/w) of the amount of soybean oil present. The production of ethyl esters by enzymatic ethanolysis was not influenced by the addition of water up to 4.0% (v/v) of the alcohol indicating that it is possible to use hydrated ethanol in the production of biodiesel catalyzed by lipase. The immobilized enzyme showed high stability under moderate reaction conditions and retained its activity after five production cycles. The (1)H NMR methodology elaborated for the quantification of biodiesel in unpurified reaction mixtures showed good correlations between the signal areas of peaks associated with the alpha-methylene groups of the ethyl esters and those of the triacyl-glycerides in residual soybean oil. Monoacylglycerides, diacylglycerides and triglycerides could also be detected and quantified in the crude biodiesel using (1)H NMR spectroscopic and GC-FID chromatographic methods. The biodiesel production by enzymatic catalysis was promising. In this case, was produced a low concentration of glycerol (0.74%) and easily removed by water extraction. (C) 2010 Elsevier B.V. All rights reserved.

Transesterification of fish oil to produce fatty acid ethyl esters using ultrasonic energy

This study evaluated the production of fatty acid ethyl esters from fish oil using ultrasonic energy and alkaline catalysts dissolved in ethanol. The feasibility of fatty acid ethyl ester production was determined using an ultrasonic bath and probe, and between 0.5 and 1% KOH (added to the fish oil). Furthermore, factors such as ultrasonic device (bath and probe), catalyst (KOH and C2H5ONa), temperature (20 and 60 °C), and duration of exposure (10–90 min) were assessed. Sodium ethoxide was found to be a more efficient catalyst than KOH when transesterifying fish oil. Ultrasonic energy applied for greater than 30 min at 60 °C using 0.8% of C2H5ONa as a catalyst transesterified over 98% fish oil triglycerides to fatty acid ethyl esters. It is reasonable to conclude that the yield of fatty acid ethyl esters produced by applying ultrasonic energy to fish oil is related to the sonication time. Due to increases in the surface area contact between the reactants and the catalyst, ultrasonic energy has the potential to reduce the production time required by a conventional large-scale commercial transesterification method that uses agitation as a way of mixing.

Potentialities of two solventless extraction approaches—Stir bar sorptive extraction and headspace solid-phase microextraction for determination of higher alcohol acetates, isoamyl esters and ethyl esters in wines

A stir bar sorptive extraction with liquid desorption followed by large volume injection coupled to gas chromatography–quadrupole mass spectrometry (SBSE-LD/LVI-GC–qMS) was evaluated for the simultaneous determination of higher alcohol acetates (HAA), isoamyl esters (IsoE) and ethyl esters (EE) of fatty acids. The method performance was assessed and compared with other solventless technique, the solid-phase microextraction (SPME) in headspace mode (HS). For both techniques, influential experimental parameters were optimised to provide sensitive and robust methods. The SBSE-LD/LVI methodology was previously optimised in terms of extraction time, influence of ethanol in the matrix, liquid desorption (LD) conditions and instrumental settings. Higher extraction efficiency was obtained using 60 min of extraction time, 10% ethanol content, n-pentane as desorption solvent, 15 min for the back-extraction period, 10 mL min−1 for the solvent vent flow rate and 10 °C for the inlet temperature. For HS-SPME, the fibre coated with 50/30 μm divinylbenzene/carboxen/polydimethylsiloxane (DVB/CAR/PDMS) afforded highest extraction efficiency, providing the best sensitivity for the target volatiles, particularly when the samples were extracted at 25 °C for 60 min under continuous stirring in the presence of sodium chloride (10% (w/v)). Both methodologies showed good linearity over the concentration range tested, with correlation coefficients higher than 0.984 for HS-SPME and 0.982 for SBES-LD approach, for all analytes. A good reproducibility was attained and low detection limits were achieved using both SBSE-LD (0.03–28.96 μg L−1) and HS-SPME (0.02–20.29 μg L−1) methodologies. The quantification limits for SBSE-LD approach ranging from 0.11 to 96.56 μg L−and from 0.06 to 67.63 μg L−1 for HS-SPME. Using the HS-SPME approach an average recovery of about 70% was obtained whilst by using SBSE-LD obtained average recovery were close to 80%. The analytical and procedural advantages and disadvantages of these two methods have been compared. Both analytical methods were used to determine the HAA, IsoE and EE fatty acids content in “Terras Madeirenses” table wines. A total of 16 esters were identified and quantified from the wine extracts by HS-SPME whereas by SBSE-LD technique were found 25 esters which include 2 higher alcohol acetates, 4 isoamyl esters and 19 ethyl esters of fatty acids. Generally SBSE-LD provided higher sensitivity with decreased analysis time.

Determination of fatty acid ethyl esters in dried blood spots by LC-MS/MS as markers for ethanol intake: application in a drinking study.

The forensic utility of fatty acid ethyl esters (FAEEs) in dried blood spots (DBS) as short-term confirmatory markers for ethanol intake was examined. An LC-MS/MS method for the determination of FAEEs in DBS was developed and validated to investigate FAEE formation and elimination in a drinking study, whereby eight subjects ingested 0.66-0.84 g/kg alcohol to reach blood alcohol concentrations (BAC) of 0.8 g/kg. Blood was taken every 1.5-2 h, BAC was determined, and dried blood spots were prepared, with 50 μL of blood, for the determination of FAEEs. Lower limits of quantitation (LLOQ) were between 15 and 37 ng/mL for the four major FAEEs. Validation data are presented in detail. In the drinking study, ethyl palmitate and ethyl oleate proved to be the two most suitable markers for FAEE determination. Maximum FAEE concentrations were reached in samples taken 2 or 4 h after the start of drinking. The following mean peak concentrations (c̅ max) were reached: ethyl myristate 14 ± 4 ng/mL, ethyl palmitate 144 ± 35 ng/mL, ethyl oleate 125 ± 55 ng/mL, ethyl stearate 71 ± 21 ng/mL, total FAEEs 344 ± 91 ng/mL. Detectability of FAEEs was found to be on the same time scale as BAC. In liquid blood samples containing ethanol, FAEE concentrations increase post-sampling. This study shows that the use of DBS fixation prevents additional FAEE formation in blood samples containing ethanol. Positive FAEE results obtained by DBS analysis can be used as evidence for the presence of ethanol in the original blood sample. Graphical Abstract Time courses for fatty acid ethyl ester (FAEE) concentrations in DBS and ethanol concentrations for subject 1 over a period of 7 h. Ethanol ingestion occured during the first hour of the time course.

Hydrotelluration of acetylenic esters: structural characterization of stereoisomers of methyl/ethyl beta-(aryltelluro)acrylates

Synthesis and complete characterization of some ester functionalized vinylic tellurides bearing an aryl ligand with varying steric and electronic effects bound to tellurium is described. Hydrotelluration of methyl propiolate using Ar2Te2/NaBH4 in methanol results in a mixture of stereoisomers of methyl β-(aryltelluro)acrylates, ArTeCH[double bond, length as m-dash]CHCOOMe (Ar = 4-MeOC6H4, 1A; 1-C10H7, 2A; 2,4,6-Me3C6H2, 3A; C5H5FeC5H4, 4A; 4-Me2NC6H4, 5A; and 2-C4H3S, 6A). The same reaction in ethanol provides isomeric mixtures of the ethyl esters ArTeCH[double bond, length as m-dash]CHCOOEt (1B–6B). However, in the reactions between methyl propiolate and Ar2Te2 (Ar = 2,4,6-Me3C6H2, 4-Me2NC6H4) in isopropanol or t-butanol, no exchange of alkyl groups between the parent ester and the solvent is observed, instead detelluration of the Ar2Te2 to Ar2Te is a competing reaction along with almost exclusive formation of the (Z)-isomers (3Aa, 5Aa). The geometry of the separated stereoisomers is established in solution, with the help of 1H, 13C and 125Te NMR spectrometry. Of particular interest is the observation that 125Te chemical shifts {deshielded in (Z) compared to (E); Δδ = 106–136 ppm} and the geminal heteronuclear coupling constants {2J(1H–125Te) values for (E) are more than seven times that of the corresponding (Z) isomer} can be used to distinguish between liquid isomers. Structural characterization in the solid state by single-crystal X-ray diffraction for the 2Ba, 3Aa, 3Ba, 5Aa, 8 (Z)-isomers as well as for both stereoisomers of 4-Me2NC6H4TeCH[double bond, length as m-dash]CHCOOEt (5Ba and 5Bb) is also presented. The carbonyl O atom of the ester group is invariably involved, at least in the solid state, in a secondary bonding interaction with the Te(II) atom. While an intermolecular Te⋯O interaction gives rise to one-dimensional supramolecular arrays in the crystal lattice of 5Bb with (E) configuration, it is realized intramolecularly in the case of the (Z)-isomers due to the cis position of the chalcogen atoms.

Anisochrony of O-methylene protons of ethyl ester functions and structural factors in the connected chiral entities

(i) Incistrans pairs of cyclic 1,3-dicarboxylic acid ethyl esters thecis-foms exhibit higher O-methylene proton (HA, HB) anisochrony than thetrans-forms; (ii) anisochrony, easily observed in certain decalin-10-carboxylic ethyl esters, ‘disappears’ on one of the rings attaining the possibility of transforming into a ‘twist’ form; (iii) in certain pairs of chiralsecethyl esters and theirtert-methylated analogues anisochrony is higher in the latter, contrary to expectation, while, in certain others, the reverse is observed. Attempted explanations are based on assessments whether H A and H B are or are not in highly different magnetic environments in confomers regarded as preferred. This subsumes the possibility thatXYZC-CO2H A H B Me chiral ethyl acetates differ fromXYZC-CH A H B Me ethanes because intervention by the carboxyl group insulates the prochiral centre and allows anisotropic effects to gain somewhat in importance among mechanisms that discriminate between H A and H B so long as rotamerpopulation inequalities persist. Background information on why rotamer-population inequalities will always persist and on a heuristic that attempts to generalize the effects ofXYZ inXYZC - CU AUB V is provided. Possible effects when connectivity exists between a pair amongX, Y, Z or when specific interactions occur betweenV andX, Y orZ are considered. An interpretation in terms of ‘increasing conformational mobility’ has been suggested for the observed increase in the rate of temperature-dependence of O-methylene anisochrony down a series of chiral ethyl esters.

Ethyl biodiesel: Microwave irradiation aiding ethanolysis of waste cooking oil.

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Production of methyl and ethyl biodiesel fuel from pequi oil (Caryocar brasiliensis Camb.)

We studied the physical and chemical characteristics of methyl and ethyl esters (biodiesel) produced by transesterification of pequi oil (Caryocar brasiliensis Camb.) in the presence of potassium hydroxide. The oil extracted from pequi seed comprises 60% of the fruit content. Such characteristics as density, acidity, viscosity, and carbon residue of the biodiesel meet ANP (Brazilian National Petroleum Agency) standards. Our tests demonstrated the feasibility of utilizing pequi oil for biodiesel production.

Purification of pharmaceuticals and nutraceutical compounds by sub- and supercritical extraction and chromatography

This thesis discusses the use of sub- and supercritical fluids as the medium in extraction and chromatography. Super- and subcritical extraction was used to separate essential oils from herbal plant Angelica archangelica. The effect of extraction parameters was studied and sensory analyses of the extracts were done by an expert panel. The results of the sensory analyses were compared to the analytically determined contents of the extracts. Sub- and supercritical fluid chromatography (SFC) was used to separate and purify high-value pharmaceuticals. Chiral SFC was used to separate the enantiomers of racemic mixtures of pharmaceutical compounds. Very low (cryogenic) temperatures were applied to substantially enhance the separation efficiency of chiral SFC. The thermodynamic aspects affecting the resolving ability of chiral stationary phases are briefly reviewed. The process production rate which is a key factor in industrial chromatography was optimized by empirical multivariate methods. General linear model was used to optimize the separation of omega-3 fatty acid ethyl esters from esterized fish oil by using reversed-phase SFC. Chiral separation of racemic mixtures of guaifenesin and ferulic acid dimer ethyl ester was optimized by using response surface method with three variables per time. It was found that by optimizing four variables (temperature, load, flowate and modifier content) the production rate of the chiral resolution of racemic guaifenesin by cryogenic SFC could be increased severalfold compared to published results of similar application. A novel pressure-compensated design of industrial high pressure chromatographic column was introduced, using the technology developed in building the deep-sea submersibles (Mir 1 and 2). A demonstration SFC plant was built and the immunosuppressant drug cyclosporine A was purified to meet the requirements of US Pharmacopoeia. A smaller semi-pilot size column with similar design was used for cryogenic chiral separation of aromatase inhibitor Finrozole for use in its development phase 2.

Produção de biodiesel por transesterificação enzimática de óleo de soja

Neste trabalho, foi investigada a alcoólise do óleo de soja com álcool utilizando uma lipase comercial imobilizada (Lipozyme RM IM). As reações foram realizadas em um reator batelada fechado acoplado a um condensador e com constante agitação. Foi determinada a influência do álcool (metanol ou etanol), quantidade de enzima, razão molar álcool/óleo de soja, solvente e temperatura na produção de biodiesel. A etanólise do óleo de soja por sucessivas adições de álcool foi investigada. As melhores condições foram obtidas em um sistema livre de solvente com razão molar etanol/óleo igual a 3,0, temperatura de 50C e concentração de enzima de 7% em massa. A etanólise em batelada com 3 adições sucessivas foi a mais eficiente para a produção de biodiesel. Nessas condições, o rendimento em ésteres etílicos foi cerca de 55% após 2h de reação. A alcoólise de óleo de soja com metanol e etanol também foi estudada com KOH. O efeito do álcool (metanol ou etanol), concentração do catalisador e razão molar entre álcool e óleo de soja foi determinada. O maior rendimento (92%) na alcoólise do óleo de soja com KOH foi obtido com metanol

Carboxilesterase na adaptação do metabolismo de lipídios do pacu à hipoxia

Os peixes são vertebrados que vivem em vários habitats. Adaptações de sua fisiologia e de sua bioquímica são estudadas para entender como conseguem sobreviver aos desafios presentes em cada ambiente. A diminuição da concentração de oxigênio dissolvido na água é um fenômeno natural cíclico em águas do Pantanal e da Amazônia. A crescente poluição antrópica dos rios da Amazônia e do Pantanal pode, somada à hipoxia, oferecer ameaça à permanência de muitas espécies de peixes. Ao estudarmos a carboxilesterase (CarbE), enzima importante para a biotransformação de xenobióticos, observamos que sua atividade diminuía em plasma de pacu, um peixe típico do Pantanal, mantido em hipoxia durante 42 horas. As carboxilesterases participam de inúmeras reações químicas no organismo, incluindo uma transesterificação capaz de produzir ésteres etílicos tóxicos de ácido graxo (FAEE, fatty acid ethyl esters) a partir de etanol e ésteres de ácidos graxos. Já que a diminuição da atividade de CarbE poderia ser uma vantagem, pois que o etanol (um produto da glicólise em peixes sob hipoxia) seria menos esterificado, resolvemos saber mais sobre a bioquímica da CarbE do plasma e do fígado de pacus. Os pacus foram submetidos à hipoxia por diminuição da concentração até 0,5 mg O2/L por meio de borbulhamento de nitrogênio na água. Os animais ficaram nessas condições por 42 horas, quando então coletamos sangue e retiramos seus fígados. A atividade de CarbE ensaiada foi 50% menor no soro e 25% menor nos microssomos de fígado se comparada com a de peixes sob 6 mg O2/L. A CarbE isolada do soro dos pacus em normoxia possui massa molecular relativa de 56.000. A eletroforese em gel desnaturante com a fração purificada rendeu três bandas, mas o gel nativo apresentou só duas bandas com atividades sobre α-naftil acetato. Inferimos que mais do que uma isoforma da enzima está no plasma dos pacus. A CarbE isolada do soro não possui atividade de lipase sobre o Tween 20, mas os microssomos dos fígados dos animais em normoxia e hipoxia possuem. No entanto, a CarbE possui atividade sobre acil-CoA assim como o microssomo de fígado. A enzima pura apresenta Vmáx três vezes maior e uma KM quatro vezes maior do que a atividade presente nos microssomos. Além disso, os microssomos do fígado dos pacus em normoxia podem hidrolisar acil-CoA com o dobro da velocidade daqueles em hipoxia. A atividade clássica de CarbE do soro foi inibida por 4-HNE a 4 mM. A atividade de acil-CoA dos microssomos de fígado também foi sensível a 4-HNE a 4 mM, enquanto 2 mM de 4-HNE inibiu metade desta atividade do soro.

Optimisation of chemoenzymatic processes in asymmetric synthesis

This thesis describes the optimisation of chemoenzymatic methods in asymmetric synthesis. Modern synthetic organic chemistry has experienced an enormous growth in biocatalytic methodologies; enzymatic transformations and whole cell bioconversions have become generally accepted synthetic tools for asymmetric synthesis. Biocatalysts are exceptional catalysts, combining broad substrate scope with high regio-, enantio- and chemoselectivities enabling the resolution of organic substrates with superb efficiency and selectivity. In this study three biocatalytic applications in enantioselective synthesis were explored and perhaps the most significant outcome of this work is the excellent enantioselectivity achieved through optimisation of reaction conditions improving the synthetic utility of the biotransformations. In the first chapter a summary of literature discussing the stereochemical control of baker’s yeast (Saccharomyces Cerevisae) mediated reduction of ketones by the introduction of sulfur moieties is presented, and sets the work of Chapter 2 in context. The focus of the second chapter was the synthesis and biocatalytic resolution of (±)-trans-2-benzenesulfonyl-3-n-butylcyclopentanone. For the first time the practical limitations of this resolution have been addressed providing synthetically useful quantities of enantiopure synthons for application in the total synthesis of both enantiomers of 4-methyloctanoic acid, the aggregation pheromone of the rhinoceros beetles of the genus Oryctes. The unique aspect of this enantioselective synthesis was the overall regio- and enantioselective introduction of the methyl group to the octanoic acid chain. This work is part of an ongoing research programme in our group focussed on baker’s yeast mediated kinetic resolution of 2-keto sulfones. The third chapter describes hydrolase-catalysed kinetic resolutions leading to a series of 3-aryl alkanoic acids. Hydrolysis of the ethyl esters with a series of hydrolases was undertaken to identify biocatalysts that yield the corresponding acids in highly enantioenriched form. Contrary to literature reports where a complete disappearance of efficiency and, accordingly enantioselection, was described upon kinetic resolution of sterically demanding 3-arylalkanoic acids, the highest reported enantiopurities of these acids was achieved (up to >98% ee) in this study through optimisation of reaction conditions. Steric and electronic effects on the efficiency and enantioselectivity of the biocatalytic transformation were also explored. Furthermore, a novel approach to determine the absolute stereochemistry of the enantiopure 3-aryl alkanoic acids was investigated through combination of co-crystallisation and X-ray diffraction linked with chiral HPLC analysis. The fourth chapter was focused on the development of a biocatalytic protocol for the asymmetric Henry reaction. Efficient kinetic resolution in hydrolase-mediated transesterification of cis- and trans- β-nitrocyclohexanol derivatives was achieved. Combination of a base-catalysed intramolecular Henry reaction coupled with the hydrolase-mediated kinetic resolution with the view to selective acetylation of a single stereoisomer was investigated. While dynamic kinetic resolution in the intramolecular Henry was not achieved, significant progress in each of the individual elements was made and significantly the feasibility of this process has been demonstrated. The final chapter contains the full experimental details, including spectroscopic and analytical data of all compounds synthesised in this project, while details of chiral HPLC analysis are included in the appendix. The data for the crystal structures are contained in the attached CD.