Development and validation of an environmentally friendly attenuated total reflectance in the mid-infrared region method for the determination of ethanol content in used engine lubrication oil

Lubricating oils are crucial in the operation of automotive engines because they both reduce friction between moving parts and protect against corrosion. However, the performance of lubricant oil may be affected by contaminants, such as gasoline, diesel, ethanol, water and ethylene glycol. Although there are many standard methods and studies related to the quantification of contaminants in lubricant oil, such as gasoline and diesel oil, to the best of our knowledge, no methods have been reported for the quantification of ethanol in used Otto cycle engine lubrication oils. Therefore, this work aimed at the development and validation of a routine method based on partial least-squares multivariate analysis combined with attenuated total reflectance in the mid-infrared region to quantify ethanol content in used lubrication oil. The method was validated based on its figures of merit (using the net analyte signal) as follows: limit of detection (0.049%), limit of quantification (0.16%), accuracy (root mean square error of prediction=0.089% w/w), repeatability (0.05% w/w), fit (R 2 =0.9997), mean selectivity (0.047), sensitivity (0.011), inverse analytical sensitivity (0.016% w/w-1) and signal-to-noise ratio (max: 812.4 and min: 200.9). The results show that the proposed method can be routinely implemented for the quality control of lubricant oils. © 2013 Elsevier B.V. All rights reserved.

Spittlebug impacts on sugarcane quality and ethanol production

The objective of this work was to evaluate the impacts of spittlebug (Mahanarva fimbriolata) attack on sugarcane quality and ethanol production. Technological and microbiological parameters of juice and fermentation process were evaluated in ten fermentation cycles and two harvest seasons. Treatments consisted of different spittlebug stalk damage levels: control, with 100% of apparently healthy stalks; medium, with 15% of damaged or dry stalks (DDS); high, with 30% of DDS; and very high, with 60% of DDS. Spittlebug attack caused significant losses in cane quality, reducing total soluble solids, sucrose content, total reducing sugars, and pH, and increasing total phenolic compounds, and total and volatile juice acidity. The fermentation process was also significantly affected, resulting in lower ethanol content in wine. There was an increase in acetaldehyde concentration in the distillate. The spittlebug attack caused negative impacts on sugarcane quality and fermentation process, and these impacts are stronger in late season harvests.

Spittlebug impacts on sugarcane quality and ethanol production

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Ethanol intake of paediatric intensive care patients

Background - Limiting the amount of alcohol in children's medicines is advisable but as alcohol is the second most common solvent used in liquid preparations, paediatric patients with increased medication intake may be exposed to a considerable alcohol intake. Few medicines are specifically designed for children in Paediatric Intensive Care (PICU), and therefore adult formulations are frequently administered, with high medication use further exposing a PICU patient to undesired alcohol intake. Aims - This small pilot study aimed to examiine the intake of a sample of PICU patients, highlight common medicines used on PICU containing alcohol, provide alternatives where possible and where alternatives are not possible, provide the prescriber with a list of the higher alcohol containing medicines. Method - A retrospective medication chart review was undertaken as a two point snap shot. Data collected included age, weight, medications prescribed and the formulations used at time of the study. The patients' sedation score was recorded. The electronic medicine compendium (EMC) was consulted for any ethanol content for the commercially available products. The manufacturer was contacted for ethanol content of all ‘specials’ and any commercial products found to contain ethanol from the EMC. The PICU patient's daily intake of ethanol was calculated. The calculation was converted to an adult equivalent alcohol unit intake and although this method of conversion is crude and does not take physiological differences of adult and children into account, it was done in order to provide the clinician with commonly used terminology in deciding the risk to the patient. Results - Twenty-eight patients were prescribed a range of 69 different medications. Of the 69 medicines, 12 products were found to contain ethanol. Patient ages ranged from a 26 week premature infant to 15 years old, weights ranges from 0.7 kg to 45 kg. Only 2 out of the 28 patients did not receive ethanol containing medications, and most patients were prescribed at least two medicines containing ethanol. Daily ethanol intake uncorrected for weight ranged from 0.006 ml to 2.18 ml (median 0.26 ml). Converting this to adult units per week, alcohol intake ranged from 0.07 to 15.2 units (median 1.4 units). The two patients receiving above 15 units/week adult equivalent were prescribed an oral morphine weaning regimen, therefore the high alcohol exposure was short term. The most common drugs prescribed containing alcohol were found to be nystatin, ranitidine, furosemide and morphine. No commercially available alcohol-free oral liquid preparations were found for ranitidine, furosemide or morphine at the time of the study. Correlation of the sedation score against ethanol intake was difficult to analyse as most patients were actively sedated. Conclusions - Polypharmacy in PICU patients increases the exposure to alcohol. Some commercially available medicines provide excessive ethanol intake, providing the clinician with ethical, potentially economical dilemmas of prescribing an unlicensed medicine to minimise ethanol exposure. Further research is required to evaluate the scope of the problem, effects of exposure and provision of alcohol free formulations.

Defects in ZnO nanoparticles laser-ablated in water-ethanol mixtures at different pressures

The effect of liquid medium and its pressure on the photoluminescence of ZnO nanoparticles prepared via laser ablation of Zn targets in various water-ethanol mixtures is studied. As the ethanol content increases, the photoluminescence of the product changes, while metallic zinc is observed to emerge in nanomaterials prepared in ethanol-rich environments. The applied pressure had a less profound effect, mainly affecting materials produced in water or water-ethanol, and much less those generated in pressurized ethanol. Tuning the reactivity of the liquid and pressurizing it during laser ablation is demonstrated to be promising for tailoring the emission properties of the product.

Valorização da Borra de Café: Otimização da Produção de Biodiesel por Catálise Enzimática

O decréscimo das reservas de petróleo e as consequências ambientais resultantes do recurso a combustíveis fósseis nos motores a diesel têm levado à procura de combustíveis alternativos. Esta pesquisa alicerçada nas fontes de energia renovável tornou-se essencial, face à crescente procura de energia e ao limitado fornecimento de combustíveis fósseis . Resíduos de óleo de cozinha, gordura animal, entre outros resíduos de origem biológica, tais como a borra de café, são exemplos de matérias-primas para a produção de biodiesel. A sua valorização tem interesse quer pela perspetiva ambiental, quer pela económica, pois aumenta não só a flexibilidade e diversificação das matérias-primas, mas também contribui para uma estabilidade de custos e alteração nas políticas agrícolas e de uso do solo. É neste contexto que se enquadra o biodiesel e a borra de café, pretendendo-se aqui efetuar o estudo da produção, à escala laboratorial, de biodiesel a partir da borra de café, por transesterificação enzimática, visando a procura das melhores condições reacionais. Iniciando-se com a caracterização da borra de café, foram avaliados antes e após a extração do óleo da borra de café, diversos parâmetros, de entre os quais se destacam: o teor de humidade (16,97% e 6,79%), teor de cinzas (1,91 e 1,57%), teor de azoto (1,71 e 2,30%), teor de proteínas (10,7 e 14,4%), teor de carbono (70,2 e 71,7%), teor de celulose bruta (14,77 e 18,48%), teor de lenhina (31,03% e 30,97%) e poder calorifico superior (19,5 MJ/kg e 19,9 MJ/kg). Sumariamente, constatou-se que os valores da maioria dos parâmetros não difere substancialmente dos valores encontrados na literatura, tendo sido evidenciado o potencial da utilização desta biomassa, como fonte calorifica para queima e geração de energia. Sendo a caracterização do óleo extraído da borra de café um dos objetivos antecedentes à produção do biodiesel, pretendeu-se avaliar os diferentes parâmetros mais significativos. No que diz respeito à caracterização do óleo extraído, distingue-se a sua viscosidade cinemática (38,04 mm2/s), densidade 0,9032 g/cm3, poder calorífico de 37,9 kcal/kg, índice de iodo igual a 63,0 gI2/ 100 g óleo, o teor de água do óleo foi de 0,15 %, o índice de acidez igual a 44,8 mg KOH/g óleo, ponto de inflamação superior a 120 ºC e teor em ácidos gordos de 82,8%. Inicialmente foram efetuados ensaios preliminares, a fim de selecionar a lipase (Lipase RMIM, TL 100L e CALB L) e álcool (metanol ou etanol puros) mais adequados à produção de biodiesel, pelo que o rendimento de 83,5% foi obtido através da transesterificação mediada pela lipase RMIM, utilizando como álcool o etanol. Sendo outro dos objetivos a otimização do processo de transesterificação enzimática, através de um desenho composto central a três variáveis (razão molar etanol: óleo, concentração de enzima e temperatura), recorrendo ao software JMP 8.0, determinou-se como melhores condições, uma razão molar etanol: óleo 5:1, adição de 4,5% (m/m) de enzima e uma temperatura de 45 ºC, que conduziram a um rendimento experimental equivalente a 96,7 % e teor de ésteres 87,6%. Nestas condições, o rendimento teórico foi de 99,98%. Procurou-se ainda estudar o efeito da adição de água ao etanol, isto é, o efeito da variação da concentração do etanol pela adição de água, para teores de etanol de 92%, 85% e 75%. Verificou-se que até 92% decorreu um aumento da transesterificação (97,2%) para um teor de ésteres de (92,2%), pelo que para teores superiores de água adicionada (75% e 85%) ocorreu um decréscimo no teor final em ésteres (77,2% e 89,9%) e no rendimento da reação (84,3% e 91,9%). Isto indica a ocorrência da reação de hidrólise em maior extensão, que leva ao desvio do equilíbrio no sentido contrário à reação de formação dos produtos, isto é, dos ésteres. Finalmente, relativamente aos custos associados ao processo de produção de biodiesel, foram estimados para o conjunto de 27 ensaios realizados neste trabalho, e que corresponderam a 767,4 g de biodiesel produzido, sendo o custo dos reagentes superior ao custo energético, de 156,16 € e 126,02 €, respetivamente. Naturalmente que não esperamos que, a nível industrial os custos sejam desta ordem de grandeza, tanto mais que há economia de escala e que as enzimas utilizadas no processo deveriam ser reutilizadas diversas vezes.

A escolha da faixa espectral no uso combinado de métodos espectroscópicos e quimiométricos

A method is presented for the choice of spectral regions when absorption measurements are coupled to chemometric tools to perform quantitative analyses. The method is based on the spectral distribution of the relative standard deviation of concentration (s c/c). It has been applied to the development of PLS-FTNIR calibration models for the determination of density and MON of gasoline, and ethanol content and density of ethanol fuel. The new method was also compared with the correlation (R²) method and has proved to generate PLS calibration models that present better accuracy and precision than those based on R².

Avaliação de laboratórios brasileiros na determinação de alguns parâmetros de qualidade de biocombustíveis

This work shows the results of a Proficiency Testing performed by a partnership between INMETRO and ANP. The performance of 49 Brazilian laboratories (using the z-score statistical test) in determining 10 quality parameters of ethanol fuel and biodiesel was evaluated. The certified reference values were provided by INMETRO, allowing a more rigorous assessment of the laboratories. For hydrous ethanol, the acidity parameter showed the lowest number of laboratories with satisfactory results (48%), while 85% of the laboratories presented satisfactory results for ethanol content. For biodiesel, the percentage of laboratories with satisfactory results ranged from 46% (kinematic viscosity) to 92% (acid number).

A sensitive microextraction by packed sorbent-based methodology combined with ultra-high pressure liquid chromatography as a powerful technique for analysis of biologically active flavonols in wines

A new approach based on microextraction by packed sorbent (MEPS) and reversed-phase high-throughput ultra high pressure liquid chromatography (UHPLC) method that uses a gradient elution and diode array detection to quantitate three biologically active flavonols in wines, myricetin, quercetin, and kaempferol, is described. In addition to performing routine experiments to establish the validity of the assay to internationally accepted criteria (selectivity, linearity, sensitivity, precision, accuracy), experiments are included to assess the effect of the important experimental parameters such as the type of sorbent material (C2, C8, C18, SIL, and C8/SCX), number of extraction cycles (extract-discard), elution volume, sample volume, and ethanol content, on the MEPS performance. The optimal conditions of MEPS extraction were obtained using C8 sorbent and small sample volumes (250 μL) in five extraction cycle and in a short time period (about 5 min for the entire sample preparation step). Under optimized conditions, excellent linearity View the MathML source(Rvalues2>0.9963), limits of detection of 0.006 μg mL−1 (quercetin) to 0.013 μg mL−1 (myricetin) and precision within 0.5–3.1% were observed for the target flavonols. The average recoveries of myricetin, quercetin and kaempferol for real samples were 83.0–97.7% with relative standard deviation (RSD, %) lower than 1.6%. The results obtained showed that the most abundant flavonol in the analyzed samples was myricetin (5.8 ± 3.7 μg mL−1). Quercetin (0.97 ± 0.41 μg mL−1) and kaempferol (0.66 ± 0.24 μg mL−1) were found in a lower concentration. The optimized MEPSC8 method was compared with a reverse-phase solid-phase extraction (SPE) procedure using as sorbent a macroporous copolymer made from a balanced ratio of two monomers, the lipophilic divinylbenzene and the hydrophilic N-vinylpyrrolidone (Oasis HLB) were used as reference. MEPSC8 approach offers an attractive alternative for analysis of flavonols in wines, providing a number of advantages including highest extraction efficiency (from 85.9 ± 0.9% to 92.1 ± 0.5%) in the shortest extraction time with low solvent consumption, fast sample throughput, more environmentally friendly and easy to perform.

Development of a novel microextraction by packed sorbent-based approach followed by ultrahigh pressure liquid chromatography as a powerful technique for quantification phenolic constituents of biological interest in wines

A novel analytical approach, based on a miniaturized extraction technique, the microextraction by packed sorbent (MEPS), followed by ultrahigh pressure liquid chromatography (UHPLC) separation combined with a photodiode array (PDA) detection, has been developed and validated for the quantitative determination of sixteen biologically active phenolic constituents of wine. In addition to performing routine experiments to establish the validity of the assay to internationally accepted criteria (linearity, sensitivity, selectivity, precision, accuracy), experiments are included to assess the effect of the important experimental parameters on the MEPS performance such as the type of sorbent material (C2, C8, C18, SIL, and M1), number of extraction cycles (extract-discard), elution volume, sample volume, and ethanol content, were studied. The optimal conditions of MEPS extraction were obtained using C8 sorbent and small sample volumes (250 μL) in five extraction cycle and in a short time period (about 5 min for the entire sample preparation step). The wine bioactive phenolics were eluted by 250 μL of the mixture containing 95% methanol and 5% water, and the separation was carried out on a HSS T3 analytical column (100 mm × 2.1 mm, 1.8 μm particle size) using a binary mobile phase composed of aqueous 0.1% formic acid (eluent A) and methanol (eluent B) in the gradient elution mode (10 min of total analysis). The method gave satisfactory results in terms of linearity with r2-values > 0.9986 within the established concentration range. The LOD varied from 85 ng mL−1 (ferulic acid) to 0.32 μg mL−1 ((+)-catechin), whereas the LOQ values from 0.028 μg mL−1 (ferulic acid) to 1.08 μg mL−1 ((+)-catechin). Typical recoveries ranged between 81.1 and 99.6% for red wines and between 77.1 and 99.3% for white wines, with relative standard deviations (RSD) no larger than 10%. The extraction yields of the MEPSC8/UHPLC–PDA methodology were found between 78.1 (syringic acid) and 99.6% (o-coumaric acid) for red wines and between 76.2 and 99.1% for white wines. The inter-day precision, expressed as the relative standard deviation (RSD%), varied between 0.2% (p-coumaric and o-coumaric acids) and 7.5% (gentisic acid) while the intra-day precision between 0.2% (o-coumaric and cinnamic acids) and 4.7% (gallic acid and (−)-epicatechin). On the basis of analytical validation, it is shown that the MEPSC8/UHPLC–PDA methodology proves to be an improved, reliable, and ultra-fast approach for wine bioactive phenolics analysis, because of its capability for determining simultaneously in a single chromatographic run several bioactive metabolites with high sensitivity, selectivity and resolving power within only 10 min. Preliminary studies have been carried out on 34 real whole wine samples, in order to assess the performance of the described procedure. The new approach offers decreased sample preparation and analysis time, and moreover is cheaper, more environmentally friendly and easier to perform as compared to traditional methodologies.

Potentialities of two solventless extraction approaches—Stir bar sorptive extraction and headspace solid-phase microextraction for determination of higher alcohol acetates, isoamyl esters and ethyl esters in wines

A stir bar sorptive extraction with liquid desorption followed by large volume injection coupled to gas chromatography–quadrupole mass spectrometry (SBSE-LD/LVI-GC–qMS) was evaluated for the simultaneous determination of higher alcohol acetates (HAA), isoamyl esters (IsoE) and ethyl esters (EE) of fatty acids. The method performance was assessed and compared with other solventless technique, the solid-phase microextraction (SPME) in headspace mode (HS). For both techniques, influential experimental parameters were optimised to provide sensitive and robust methods. The SBSE-LD/LVI methodology was previously optimised in terms of extraction time, influence of ethanol in the matrix, liquid desorption (LD) conditions and instrumental settings. Higher extraction efficiency was obtained using 60 min of extraction time, 10% ethanol content, n-pentane as desorption solvent, 15 min for the back-extraction period, 10 mL min−1 for the solvent vent flow rate and 10 °C for the inlet temperature. For HS-SPME, the fibre coated with 50/30 μm divinylbenzene/carboxen/polydimethylsiloxane (DVB/CAR/PDMS) afforded highest extraction efficiency, providing the best sensitivity for the target volatiles, particularly when the samples were extracted at 25 °C for 60 min under continuous stirring in the presence of sodium chloride (10% (w/v)). Both methodologies showed good linearity over the concentration range tested, with correlation coefficients higher than 0.984 for HS-SPME and 0.982 for SBES-LD approach, for all analytes. A good reproducibility was attained and low detection limits were achieved using both SBSE-LD (0.03–28.96 μg L−1) and HS-SPME (0.02–20.29 μg L−1) methodologies. The quantification limits for SBSE-LD approach ranging from 0.11 to 96.56 μg L−and from 0.06 to 67.63 μg L−1 for HS-SPME. Using the HS-SPME approach an average recovery of about 70% was obtained whilst by using SBSE-LD obtained average recovery were close to 80%. The analytical and procedural advantages and disadvantages of these two methods have been compared. Both analytical methods were used to determine the HAA, IsoE and EE fatty acids content in “Terras Madeirenses” table wines. A total of 16 esters were identified and quantified from the wine extracts by HS-SPME whereas by SBSE-LD technique were found 25 esters which include 2 higher alcohol acetates, 4 isoamyl esters and 19 ethyl esters of fatty acids. Generally SBSE-LD provided higher sensitivity with decreased analysis time.

Effects of corn meal and sulphuric acid on the production of cachaça

Avaliou-se o efeito da adição do fubá de milho no mosto de xarope de cana e o tratamento ácido do pé-de-cuba sobre a microbiota do processo fermentativo, acidez do vinho, grau alcoólico, rendimento e composição da cachaça. O delineamento experimental utilizado foi o de blocos casualizados, no esquema fatorial 2x3 e cinco repetições. A metodologia empregada e as análises foram as recomendadas pelo setor aguardenteiro. Os resultados permitiram concluir que a adição do ácido sulfúrico no pé-de-cuba transferiu a acidez para o vinho, não influenciando na viabilidade das leveduras, rendimento e composição da cachaça. Por outro lado, a acidificação do meio controlou as bactérias láticas no pé-de-cuba. A adição do fubá aumentou a concentração de bactérias lácticas ao final do processo fermentativo e dos álcoois homólogos superiores na cachaça, particularmente, os álcoois propílico e isobutílico.

Influência da utilização de aditivos químicos no perfil da fermentação, no valor nutritivo e nas perdas de silagens de cana-de-açúcar

Avaliou-se o efeito do uso de aditivos químicos nas perdas de matéria seca, no perfil fermentativo e no valor nutritivo de silagens de cana-de-açúcar. O experimento foi realizado em delineamento inteiramente casualizado com quatro repetições por tratamento (sete tratamentos). Os seguintes aditivos foram utilizados na confecção das silagens: controle (sem aditivo), L. buchneri, óxido e carbonato de cálcio em doses de 1,0 e 1,5% da massa verde e sulfato de cálcio a 1,0% da massa verde, diluídos em 40 litros de água por tonelada de forragem. As variáveis analisadas foram: perdas totais e gasosas, produção de efluente, recuperação de matéria seca, composição química e valor nutritivo. As menores perdas fermentativas e gasosas foram observadas nas silagens com óxido ou carbonato de cálcio, que resultaram em maior taxa de recuperação de matéria seca. da mesma forma, as silagens tratadas com estes aditivos apresentaram maior teor de carboidratos solúveis residuais e de ácido lático e reduzida fermentação alcoólica. As silagens tratadas com óxido e carbonato apresentaram, no momento da abertura, maior teor de cinzas, menor concentração de componentes fibrosos e maiores coeficientes digestibilidade da matéria seca e da matéria orgânica. O teor de proteína encontrado nessas silagens foi semelhante ao observado na forragem fresca. A ensilagem de cana-de-açúcar com L. buchneri e sulfato de cálcio possibilitou a obtenção de desempenho similar ao determinado com a silagem sem aditivos. Silagens tratadas com carbonato e óxido de cálcio apresentam maior desempenho durante o processo fermentativo.

Desenvolvimento de método analítico para determinação do teor de etanol em óleo lubrificante usado proveniente de motores ciclo Otto

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Fermentação de mosto com alto teor de sacarose para a produção de bioetanol combustível por diferentes linhagens de Saccharomyces cerevisiae usando alta densidade celular

Pós-graduação em Biotecnologia - IQ