Effects of weld strength mismatch on J and CTOD estimation procedure for SE(B) specimens

This work examines the effect of weld strength mismatch on fracture toughness measurements defined by J and CTOD fracture parameters using single edge notch bend (SE(B)) specimens. A central objective of the present study is to enlarge on previous developments of J and CTOD estimation procedures for welded bend specimens based upon plastic eta factors (eta) and plastic rotational factors (r (p) ). Very detailed non-linear finite element analyses for plane-strain models of standard SE(B) fracture specimens with a notch located at the center of square groove welds and in the heat affected zone provide the evolution of load with increased crack mouth opening displacement required for the estimation procedure. One key result emerging from the analyses is that levels of weld strength mismatch within the range +/- 20% mismatch do not affect significantly J and CTOD estimation expressions applicable to homogeneous materials, particularly for deeply cracked fracture specimens with relatively large weld grooves. The present study provides additional understanding on the effect of weld strength mismatch on J and CTOD toughness measurements while, at the same time, adding a fairly extensive body of results to determine parameters J and CTOD for different materials using bend specimens with varying geometries and mismatch levels.

Nuclear incoherent photoproduction of pi(0) and eta from 4 to 12 GeV

The mechanism of incoherent pi(0) and eta photoproduction from complex nuclei is investigated from 4 to 12 GeV with an extended version of the multicollisional Monte Carlo (MCMC) intranuclear cascade model. The calculations take into account the elementary photoproduction amplitudes via a Regge model and the nuclear effects of photon shadowing, Pauli blocking, and meson-nucleus final-state interactions. The results for pi(0) photoproduction reproduced for the first time the magnitude and energy dependence of the measured rations sigma(gamma A)/sigma(gamma N) for several nuclei (Be, C, Al, Cu, Ag, and Pb) from a Cornell experiment. The results for eta photoproduction fitted the inelastic background in Cornell's yields remarkably well, which is clearly not isotropic as previously considered in Cornell's analysis. With this constraint for the background, the eta -> gamma gamma. decay width was extracted using the Primakoff method, combining Be and Cu data [Gamma(eta ->gamma gamma) = 0.476(62) keV] and using Be data only [Gamma(eta ->gamma gamma) = 0.512(90) keV]; where the errors are only statistical. These results are in sharp contrast (similar to 50-60%) with the value reported by the Cornell group [Gamma(eta ->gamma gamma). = 0.324(46) keV] and in line with the Particle Data Group average of 0.510(26) keV.

Nuclear incoherent photoproduction of pi(0) and eta from 4 to 12 GeV

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Rietveld refinement and optical properties of SrWO4:Eu3+ powders prepared by the non-hydrolytic sol-gel method

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

A search for an exotic meson in the gamma + P decaying to delta++ + pi- + eta reaction

A Partial Waves Analysis (PWA) of γp → Δ ++X → pπ+ π - (η) data taken with the CLAS detector at Jefferson Lab is presented in this work. This reaction is of interest because the Δ++ restricts the isospin of the possible X states, leaving the PWA with a smaller combination of partial waves, making it ideal to look for exotic mesons. It was proposed by Isgur and Paton that photoproduction is a plausible source for the Jpc=1–+ state through flux tube excitation. The π1(1400) is such a state that has been produced with the use of hadron production but it has yet to be seen in photoproduction. A mass independent amplitude analysis of this channel was performed, followed by a mass dependent fit to extract the resonance parameters. The procedure used an event-based maximum likelihood method to maintain all correlations in the kinematics. The intensity and phase motion is mapped out for the contributing signals without requiring assumptions about the underlying processes. The strength of the PWA is in the analysis of the phase motion, which for resonance behavior is well defined. In the data presented, the ηπ– invariant mass spectrum shows contributions from the a0(980) and a2(1320) partial waves. No π1 was observed under a clear a2 signal after the angular distributions of the decay products were analyzed using an amplitude analysis. In addition, this dissertation discusses trends in the data, along with the implemented techniques.

Otimização do método QuEChERS para determinação de agrotóxicos, fármacos e produtos de cuidado pessoal em lodo de ETA por LC-ESI-MS/MS

O lodo gerado em Estação de Tratamento de Água (ETA) durante as etapas de floculação e decantação é classificado como resíduo não inerte. Estudos recentes apontam para uma diminuição na concentração de agrotóxicos, fármacos e Produtos de Cuidado Pessoal (PCP) em águas, após o seu tratamento. Uma possível explicação seja que estes compostos possam estar ficando aderidos ao lodo; entretanto, a investigação desses compostos no lodo de ETA é bastante reduzida. Neste trabalho, foi realizada a otimização do método QuEChERS com determinação por Cromatografia Líquida acoplada a Espectrometria de Massas sequencial para analisar agrotóxicos (atrazina, simazina, clomazona e tebuconazol), fármacos (amitriptilina, cafeína, diclofenaco e ibuprofeno) e PCP (metilparabeno, propilparabeno, triclocarban e bisfenol A) em lodo de ETA, uma matriz bastante complexa, constituída basicamente de compostos inorgânicos (areia, argila e silte) e orgânicos (substâncias húmicas). Após otimizado, o método apresentou limites de quantificação ente 1 e 50 µg kg-1 e as curvas analíticas apresentaram valores de r maiores que 0,98. As recuperações variaram entre 50 e 120% com RSD ≤ 15%. O efeito matriz foi avaliado e observou-se a supressão do sinal para a maioria dos compostos, sendo o efeito compensado utilizando a quantificação por superposição na matriz. O método foi aplicado em amostras de lodo de ETA e foram identificados tebuconazol e metilparabeno em concentrações

Arku fazial birtualaren balidazioa eta optimizazioa

[EU]"Arku fazial birtualaren balidazioa eta optimizazioa". Odontologian eta, oro har, medikuntzan, prozesu birtualek geroz eta indar handiagoa hartzen dabiltza, bai espezialista baita pazienteei erraztasuna emateko asmoz. Ildo horretatik jarraituz, protesien eta hortz-errestaurazioen kasuan, ikerketa sakonak burutu dira, prozesuaren ahalik eta zatirik handiena digitalizatzeko. Digitalizazio prozesu honetan CAD/CAM sistemaren aurrerapenek ere zeresan handia izan dute; izan ere, protesi eta errestaurazioen prozesu tradizionala ordezkatzea ahalbidetu du. Prozesu digitalek hainbat onura suposatu arren, zein fidagarriak diren konprobatzea ezinbestekoa da, prozesuarentzat metodologiarik egokiena aukeratu ahal izateko. Horretan zentratzen da hain zuzen proiektu hau. Protesien diseinu birtuala egin ahal izateko, beharrezkoa da horzduren kokapen birtuala lortzea, artikulagailu birtualean kokatu ahal izateko. Horretarako arku fazial birtuala erabiliko da, baina oraindik ez da metodologiarik egokiena zein den konprobatu. Beraz, proiektu honen helburua arku fazial birtual egokiena zein den zehaztea da, horretarako metodologia ezberdinak konparatuko direlarik bai modelo ez-erreala erabiliz (in vitro) baita paziente errealekin (in vivo). Horrela, prozesu ezberdinen zehaztasuna zein den konprobatu ahal izango da, bakoitzaren egiazkotasuna eta doitasuna aztertuz. Emaitzetan oinarrituz, arku fazial birtual gisa metodologiarik egokiena zein den ondorioztatu ahal izango da.

Iraupen luzeko irakasleriaren garapenaren inpaktu-mailak: kontzepzioetan, hezkuntza hurbilketan eta kultura instituzionalean

[EUS]Unibertsitateko irakasleriaren garapenaren(IG) kontzeptu konprentsibotik abiatuta, doktorego tesi honek iraupen luzeko IG programen inpaktua du aztergai, bai maila indibidualean (kontzepzio eta hurbilketan) eta baita maila organizazional zein instituzionalean ere. Azterketa hau burutzeko metodologia aktiboen (arazoetan, proiektuetan eta kasuetan oinarritutako ikaskuntza) ERAGIN programaren lehendabiziko promozioa hartuko da kasu gisa. Iraupen luzeko estrategiaren (350 ordu) bidez eta ko-mentoria taldeen funtzionamenduan oinarrituz, ikerlan enpirikoak IG-ak irakasleriaren ikas-irakaskuntza kontzepzioetan eta hurbilketan izandako inpaktuaz ageriko ebidentziak ematen ditu, baina baita ikas-irakaskuntzaren inguruan ikertzeko (scholarship of teaching and learning) eta irakaskuntza eremuetan liderra izateko gaitasunaz ere. Honako alderdiok aldaketa organizazionalean murgiltzen gaituzte eta curriculum hibridoaren pausokako gauzapenaren alde lan egiten dute.

Fabrication and characterization of a nanostructured TiO2/In2S3-Sb2S3/CuSCN extremely thin absorber (eta) solar cell

CuSCN extremely thin absorber solar cell. Nanostructured TiO2 deposited by screen printing on an ITO substrate was used as an n-type electrode. An ∼80 nm extremely thin layer of the system In2S3-Sb2S3 deposited by successive ionic layer adsorption and a reaction (silar) method was used as an absorber. The voids were filled with p-type CuSCN and the entire assembly was completed with a gold contact. The solar cell fabricated with this heterostructure showed an energy conversion efficiency of 4.9%, which is a promising result in the development of low cost and simple fabrication of solar cells.

A Highly Improved Method For Sensitive Determination Of Amitriptyline In Pharmaceutical Formulations Using An Unmodified Carbon Nanotube Electrode In The Presence Of Sulfuric Acid.

The present paper describes a novel, simple and reliable differential pulse voltammetric method for determining amitriptyline (AMT) in pharmaceutical formulations. It has been described for many authors that this antidepressant is electrochemically inactive at carbon electrodes. However, the procedure proposed herein consisted in electrochemically oxidizing AMT at an unmodified carbon nanotube paste electrode in the presence of 0.1 mol L(-1) sulfuric acid used as electrolyte. At such concentration, the acid facilitated the AMT electroxidation through one-electron transfer at 1.33 V vs. Ag/AgCl, as observed by the augmentation of peak current. Concerning optimized conditions (modulation time 5 ms, scan rate 90 mV s(-1), and pulse amplitude 120 mV) a linear calibration curve was constructed in the range of 0.0-30.0 μmol L(-1), with a correlation coefficient of 0.9991 and a limit of detection of 1.61 μmol L(-1). The procedure was successfully validated for intra- and inter-day precision and accuracy. Moreover, its feasibility was assessed through analysis of commercial pharmaceutical formulations and it has been compared to the UV-vis spectrophotometric method used as standard analytical technique recommended by the Brazilian Pharmacopoeia.

Influence Of Delivery Method On Neuroprotection By Bone Marrow Mononuclear Cell Therapy Following Ventral Root Reimplantation With Fibrin Sealant.

The present work compared the local injection of mononuclear cells to the spinal cord lateral funiculus with the alternative approach of local delivery with fibrin sealant after ventral root avulsion (VRA) and reimplantation. For that, female adult Lewis rats were divided into the following groups: avulsion only, reimplantation with fibrin sealant; root repair with fibrin sealant associated with mononuclear cells; and repair with fibrin sealant and injected mononuclear cells. Cell therapy resulted in greater survival of spinal motoneurons up to four weeks post-surgery, especially when mononuclear cells were added to the fibrin glue. Injection of mononuclear cells to the lateral funiculus yield similar results to the reimplantation alone. Additionally, mononuclear cells added to the fibrin glue increased neurotrophic factor gene transcript levels in the spinal cord ventral horn. Regarding the motor recovery, evaluated by the functional peroneal index, as well as the paw print pressure, cell treated rats performed equally well as compared to reimplanted only animals, and significantly better than the avulsion only subjects. The results herein demonstrate that mononuclear cells therapy is neuroprotective by increasing levels of brain derived neurotrophic factor (BDNF) and glial derived neurotrophic factor (GDNF). Moreover, the use of fibrin sealant mononuclear cells delivery approach gave the best and more long lasting results.

Uv-vis Spectra As An Alternative To The Lowry Method For Quantify Hair Damage Induced By Surfactants.

It is well known that long term use of shampoo causes damage to human hair. Although the Lowry method has been widely used to quantify hair damage, it is unsuitable to determine this in the presence of some surfactants and there is no other method proposed in literature. In this work, a different method is used to investigate and compare the hair damage induced by four types of surfactants (including three commercial-grade surfactants) and water. Hair samples were immersed in aqueous solution of surfactants under conditions that resemble a shower (38 °C, constant shaking). These solutions become colored with time of contact with hair and its UV-vis spectra were recorded. For comparison, the amount of extracted proteins from hair by sodium dodecyl sulfate (SDS) and by water were estimated by the Lowry method. Additionally, non-pigmented vs. pigmented hair and also sepia melanin were used to understand the washing solution color and their spectra. The results presented herein show that hair degradation is mostly caused by the extraction of proteins, cuticle fragments and melanin granules from hair fiber. It was found that the intensity of solution color varies with the charge density of the surfactants. Furthermore, the intensity of solution color can be correlated to the amount of proteins quantified by the Lowry method as well as to the degree of hair damage. UV-vis spectrum of hair washing solutions is a simple and straightforward method to quantify and compare hair damages induced by different commercial surfactants.

Graded Meshes In Bio-thermal Problems With Transmission-line Modeling Method.

In this study, the transmission-line modeling (TLM) applied to bio-thermal problems was improved by incorporating several novel computational techniques, which include application of graded meshes which resulted in 9 times faster in computational time and uses only a fraction (16%) of the computational resources used by regular meshes in analyzing heat flow through heterogeneous media. Graded meshes, unlike regular meshes, allow heat sources to be modeled in all segments of the mesh. A new boundary condition that considers thermal properties and thus resulting in a more realistic modeling of complex problems is introduced. Also, a new way of calculating an error parameter is introduced. The calculated temperatures between nodes were compared against the results obtained from the literature and agreed within less than 1% difference. It is reasonable, therefore, to conclude that the improved TLM model described herein has great potential in heat transfer of biological systems.

Trichomes Related To An Unusual Method Of Water Retention And Protection Of The Stem Apex In An Arid Zone Perennial Species.

It is well known that trichomes protect plant organs, and several studies have investigated their role in the adaptation of plants to harsh environments. Recent studies have shown that the production of hydrophilic substances by glandular trichomes and the deposition of this secretion on young organs may facilitate water retention, thus preventing desiccation and favouring organ growth until the plant develops other protective mechanisms. Lychnophora diamantinana is a species endemic to the Brazilian 'campos rupestres' (rocky fields), a region characterized by intense solar radiation and water deficits. This study sought to investigate trichomes and the origin of the substances observed on the stem apices of L. diamantinana. Samples of stem apices, young and expanded leaves were studied using standard techniques, including light microscopy and scanning and transmission electron microscopy. Histochemical tests were used to identify the major groups of metabolites present in the trichomes and the hyaline material deposited on the apices. Non-glandular trichomes and glandular trichomes were observed. The material deposited on the stem apices was hyaline, highly hydrophilic and viscous. This hyaline material primarily consists of carbohydrates that result from the partial degradation of the cell wall of uniseriate trichomes. This degradation occurs at the same time that glandular trichomes secrete terpenoids, phenolic compounds and proteins. These results suggest that the non-glandular trichomes on the leaves of L. diamantinana help protect the young organ, particularly against desiccation, by deposition of highly hydrated substances on the apices. Furthermore, the secretion of glandular trichomes probably repels herbivore and pathogen attacks.

Tissue Microarray Is A Reliable Method For Immunohistochemical Analysis Of Pleomorphic Adenoma.

To determine the most adequate number and size of tissue microarray (TMA) cores for pleomorphic adenoma immunohistochemical studies. Eighty-two pleomorphic adenoma cases were distributed in 3 TMA blocks assembled in triplicate containing 1.0-, 2.0-, and 3.0-mm cores. Immunohistochemical analysis against cytokeratin 7, Ki67, p63, and CD34 were performed and subsequently evaluated with PixelCount, nuclear, and microvessel software applications. The 1.0-mm TMA presented lower results than 2.0- and 3.0-mm TMAs versus conventional whole section slides. Possibly because of an increased amount of stromal tissue, 3.0-mm cores presented a higher microvessel density. Comparing the results obtained with one, two, and three 2.0-mm cores, there was no difference between triplicate or duplicate TMAs and a single-core TMA. Considering the possible loss of cylinders during immunohistochemical reactions, 2.0-mm TMAs in duplicate are a more reliable approach for pleomorphic adenoma immunohistochemical study.