Estudo paramétrico para um muro de gravidade submetido a carregamentos sísmicos.

A presente dissertação apresenta um estudo do comportamento de um muro de gravidade flexível submetido a carregamentos sísmicos. A influência do carregamento sísmico, e mais precisamente da variação da aceleração horizontal de pico é avaliada num estudo paramétrico, através da análise dos resultados obtidos para os deslocamentos e acelerações horizontais que ocorreram no paramento do muro de gravidade. Optou-se pela análise ao longo do tempo, introduzindo o carregamento sísmico ao modelo numérico do qual fazia parte o muro de gravidade através de 5 históricos temporais de acelerogramas horizontais normalizados em 0,05g, 0,10g, 0,15g, 0,20g e 0,25g. O evento sísmico de origem dos acelerogramas normalizados foi o terremoto ocorrido no Chile em 27 de fevereiro de 2010 e medido na estação em San Jose de Maipo, a 332,7km do epicentro do terremoto. Utiliza-se um software computacional aplicado à Geotecnia, o Plaxis, para a calibração de um modelo numérico em situação estática e posterior desenvolvimento das análises paramétricas em condições sísmicas. As análises realizadas para avaliação do comportamento do muro de gravidade em condição sísmica foram a verificação da influência da variação do acelerograma horizontal normalizada introduzido na base do modelo nos valores das acelerações e deslocamentos horizontais atuantes no muro e a verificação da influência do carregamento sísmico em comparação com a situação estática, comparando-se os valores dos deslocamentos horizontais obtidos na análise estática e nas análises dinâmicas. Os fatores que influenciam potencialmente nos resultados numéricos em condições sísmicas foram apresentados, destacando-se os aspectos relacionados à modelagem numérica em condição de sismo. Os modelos constitutivos oferecidos, a possibilidade de incorporação do carregamento sísmico na base do modelo e a possibilidade de consideração do amortecimento visco-elástico de Rayleigh nos materiais são as principais qualidades do Plaxis, utilizado na modelagem numérica. Avaliou-se positivamente a potencialidade do Plaxis, visto que o programa mostrou-se uma ferramenta capaz de simular o comportamento de muros de gravidade sujeitos a carregamentos sísmicos.

Modelação e estudo paramétrico do comportamento de vigas de betão armado com Varões de GFRP

A introdução de um novo material para a execução de estruturas, implica um amplo estudo sobre o mesmo, para que seja aceite como um material de utilização, ou solução, corrente na engenharia civil. Os varões plásticos reforçados com fibra de vidro, GFRP,apresentam-se com diversas vantagens para uma solução de substituição das tradicionais armaduras de aço no betão armado. Um Estado da Arte foi apurado para determinar o ponto de situação do conhecimento e dos estudos realizados por vários autores, desde o início das pesquisas até aos mais recentes estudos disponíveis. Neste seguimento, o presente estudo incide na análise do comportamento à flexão de vigas contínuas de betão armado com varões de GFRP, submetidas a um carregamento distribuído. O trabalho realiza-se com base em 18 modelos de elementos finitos para uma análise paramétrica, sendo os parâmetros estudados, o vão, a percentagem de armadura de flexão e a esbelteza da secção. Para validação do modelo foram, modeladas 7 vigas reais ensaiadas no âmbito de trabalhos de investigação de dois autores Os resultados das modelações das análises paramétricas foram comparados com uma análise elástica e uma análise plástica, utilizando a metodologia do ACI 440.1R-06, para a carga última de dimensionamento. Outras comparações foram feitas através dos limites de deformação do EN 1992-1-1, 2004. Analisa-se a distribuição de esforços, não elásticos, devido à perda de rigidez da viga. Os modelos das vigas mais esbeltas e com menor percentagem de armadura mostraram maior concordância com a análise realizada. As deformações comparadas com o limite L/250 mostram concordância de resultados.

Estudo paramétrico da segregação gravitacional na injeção contínua de vapor

Steam injection is the most used method of additional recovery for the extraction of heavy oil. In this type procedure is common to happen gravitational segregation and this phenomenon can affect the production of oil and therefore, it shoulds be considered in the projects of continuous steam injection. For many years, the gravitational segregation was not adequately considered in the calculation procedures in Reservoir Engineering. The effect of the gravity causes the segregation of fluids inside the porous media according to their densities. The results of simulation arising from reservoirs could provide the ability to deal with the gravity, and it became apparent that the effects of the gravity could significantly affect the performance of the reservoir. It know that the gravitational segregation can happen in almost every case where there is injection of light fluid, specially the steam, and occurs with greater intensity for viscous oil reservoirs. This work discusses the influence of some parameters of the rock-reservoir in segregation as viscosity, permeability, thickness, cover gas, porosity. From a model that shows the phenomenon with greater intensity, optimized some operational parameters as the rate flow rate steam, distance between the wells injector-producer, and interval of completion which contributed to the reduction in gravity override, thus increasing the oil recovery. It was shown a greater technical-economic viability for the model of distance between the wells 100 m. The analysis was performed using the simulator of CMG (Computer Modeling Group-Stars 2007.11, in which was observed by iterating between studied variables in heavy oil reservoirs with similar characteristics to Brazilian Northeast

Estudo paramétrico da recuperação de óleo no processo de drenagem gravitacional com injeção de CO2

The gas injection has become the most important IOR process in the United States. Furthermore, the year 2006 marks the first time the gas injection IOR production has surpassed that of steam injection. In Brazil, the installation of a petrochemical complex in the Northeast of Brazil (Bahia State) offers opportunities for the injection of gases in the fields located in the Recôncavo Basin. Field-scale gas injection applications have almost always been associated with design and operational difficulties. The mobility ratio, which controls the volumetric sweep, between the injected gas and displaced oil bank in gas processes, is typically unfavorable due to the relatively low viscosity of the injected gas. Furthermore, the difference between their densities results in severe gravity segregation of fluids in the reservoirs, consequently leading to poor control in the volumetric sweep. Nowadays, from the above applications of gas injection, the WAG process is most popular. However, in attempting to solve the mobility problems, the WAG process gives rise to other problems associated with increased water saturation in the reservoir including diminished gas injectivity and increased competition to the flow of oil. The low field performance of WAG floods with oil recoveries in the range of 5-10% is a clear indication of these problems. In order to find na effective alternative to WAG, the Gas Assisted Gravity Drainage (GAGD) was developed. This process is designed to take advantage of gravity force to allow vertical segregation between the injected CO2 and reservoir crude oil due to their density difference. This process consists of placing horizontal producers near the bottom of the pay zone and injecting gás through existing vertical wells in field. Homogeneous models were used in this work which can be extrapolated to commercial application for fields located in the Northeast of Brazil. The simulations were performed in a CMG simulator, the STARS 2007.11, where some parameters and their interactions were analyzed. The results have shown that the CO2 injection in GAGD process increased significantly the rate and the final recovery of oil

Estudo paramétrico da injeção de vapor em reservatórios delgados

Exploration of heavy oil reservoirs is increasing every year in worldwide, because the discovery of light oil reservoirs is becoming increasingly rare. This fact has stimulated the research with the purpose of becoming viable, technically and economically, the exploration of such oil reserves. In Brazil, in special in the Northeast region, there is a large amount of heavy oil reservoir, where the recovery by the so called secondary methods Water injection or gas injection is inefficient or even impracticable in some reservoirs with high viscosity oils (heavy oils). In this scenario, steam injection appears as an interesting alternative for recover of these kinds of oil reservoirs. Its main mechanism consists of oil viscosity reduction through steam injection, increasing reservoir temperature. This work presents a parametric simulation study of some operational and reservoir variables that had influence on oil recovery in thin reservoirs typically found in Brazilian Northeast Basins, that use the steam injection as improved oil recovery method. To carry out simulations, it was used the commercial software STARS (Steam, Thermal, and Advanced Processes Reservoir Simulator) from CMG (Computer Modeling Group) version 2007.11. Reservoirs variables studied were horizontal permeability, vertical and horizontal permeability ratio, water zone and pay zone thickness ratio, pay zone thickness and thermal conductivity of the rock. Whereas, operational parameters studied were distance between wells and steam injection rate. Results showed that reservoir variables that had more influence on oil recovery were horizontal permeability and water zone and pay zone thickness ratio. In relation to operational variables, results showed that short distances between wells and low steam injection rates improved oil recovery

Estudo paramétrico da recuperação de petróleo pesado por aquecimento eletromagnético resistivo

Electrical resistive heating (ERH) is a thermal method used to improve oil recovery. It can increase oil rate and oil recovery due to temperature increase caused by electrical current passage through oil zone. ERH has some advantage compared with well-known thermal methods such as continuous steam flood, presenting low-water production. This method can be applied to reservoirs with different characteristics and initial reservoir conditions. Commercial software was used to test several cases using a semi-synthetic homogeneous reservoir with some characteristics as found in northeast Brazilian basins. It was realized a sensitivity analysis of some reservoir parameters, such as: oil zone, aquifer presence, gas cap presence and oil saturation on oil recovery and energy consumption. Then it was tested several cases studying the electrical variables considered more important in the process, such as: voltage, electrical configurations and electrodes positions. Energy optimization by electrodes voltage levels changes and electrical settings modify the intensity and the electrical current distribution in oil zone and, consequently, their influences in reservoir temperature reached at some regions. Results show which reservoir parameters were significant in order to improve oil recovery and energy requirement in for each reservoir. Most significant parameters on oil recovery and electrical energy delivered were oil thickness, presence of aquifer, presence of gas cap, voltage, electrical configuration and electrodes positions. Factors such as: connate water, water salinity and relative permeability to water at irreducible oil saturation had low influence on oil recovery but had some influence in energy requirements. It was possible to optimize energy consumption and oil recovery by electrical variables. Energy requirements can decrease by changing electrodes voltages during the process. This application can be extended to heavy oil reservoirs of high depth, such as offshore fields, where nowadays it is not applicable any conventional thermal process such as steam flooding

Estudo paramétrico do processo de injeção de solventes em poços horizontais para reservatórios de óleos pesados

The world has many types of oil that have a range of values of density and viscosity, these are characteristics to identify whether an oil is light, heavy or even ultraheavy. The occurrence of heavy oil has increased significantly and pointing to a need for greater investment in the exploitation of deposits and therefore new methods to recover that oil. There are economic forecasts that by 2025, the heavy oil will be the main source of fossil energy in the world. One such method is the use of solvent vaporized VAPEX which is known as a recovery method which consists of two horizontal wells parallel to each other, with a gun and another producer, which uses as an injection solvent that is vaporized in order to reduce the viscosity of oil or bitumen, facilitating the flow to the producing well. This method was proposed by Dr. Roger Butler, in 1991. The importance of this study is to analyze how the influence some operational reservoir and parameters are important in the process VAPEX, such as accumulation of oil produced in the recovery factor in flow injection and production rate. Parameters such as flow injection, spacing between wells, type of solvent to be injected, vertical permeability and oil viscosity were addressed in this study. The results showed that the oil viscosity is the parameter that showed statistically significant influence, then the choice of Heptane solvent to be injected showed a greater recovery of oil compared to other solvents chosen, considering the spacing between the wells was shown that for a greater distance between the wells to produce more oil

Estudo paramétrico da injeção de polímeros em reservatórios de petróleo

Developing an efficient methodology for oil recovery is extremely important . Within the range of enh anced oil recovery, known as EOR, the injection of polymer solutions becomes effective in controlling the mobility of displacing fluid . This method consists of adding polymers to the injection water to increase its viscosity, so that more water diffuses in to the porous medium and increasing the sweep efficiency in the reservoir. This work is studied by numerical simulation , application of the injection polymer solution in a homogeneous reservoir , semisynthetic with similar characteristics to the reservoirs of the Brazilian Northeast , numerical simulations were performed using thermal simulator STARS from CMG (Computer Modelling Group ). The study aimed to analyze the influence of some parameters on the behavior of reservoir oil production, with the response to cumulative production. Simulations were performed to analyze the influence of water injection, polymer solution and alternating injection of water banks and polymer solution, comparing the results for each simulated condition. The primary outcomes were: oil viscosity, percentage of injected polymer, polymer viscosity and flow rate of water injection. The evaluation of the influence of variables consisted of a complete experimental design followed a Pareto analysis for the purpose of pointing out which va riables would be most influential on the response represented b y the cumulative oil production . It was found that all variables significantly influenced the recovery of oil and the injection of polymer solution on an ongoing basis is more efficient for the cumulative production compared to oil recovery by continuous water injection. The primary recovery show ed low levels of oil production , water injection significantly improves the pro duction of oil in the reservoir , but the injection of polymer solution em erges as a new methodology to increase the production of oil, increasing the life of the well and possible reduction of water produced.

Estudo paramétrico da segregação gravitacional na injeção contínua de vapor

Steam injection is the most used method of additional recovery for the extraction of heavy oil. In this type procedure is common to happen gravitational segregation and this phenomenon can affect the production of oil and therefore, it shoulds be considered in the projects of continuous steam injection. For many years, the gravitational segregation was not adequately considered in the calculation procedures in Reservoir Engineering. The effect of the gravity causes the segregation of fluids inside the porous media according to their densities. The results of simulation arising from reservoirs could provide the ability to deal with the gravity, and it became apparent that the effects of the gravity could significantly affect the performance of the reservoir. It know that the gravitational segregation can happen in almost every case where there is injection of light fluid, specially the steam, and occurs with greater intensity for viscous oil reservoirs. This work discusses the influence of some parameters of the rock-reservoir in segregation as viscosity, permeability, thickness, cover gas, porosity. From a model that shows the phenomenon with greater intensity, optimized some operational parameters as the rate flow rate steam, distance between the wells injector-producer, and interval of completion which contributed to the reduction in gravity override, thus increasing the oil recovery. It was shown a greater technical-economic viability for the model of distance between the wells 100 m. The analysis was performed using the simulator of CMG (Computer Modeling Group-Stars 2007.11, in which was observed by iterating between studied variables in heavy oil reservoirs with similar characteristics to Brazilian Northeast

Estudo paramétrico da recuperação de óleo no processo de drenagem gravitacional com injeção de CO2

The gas injection has become the most important IOR process in the United States. Furthermore, the year 2006 marks the first time the gas injection IOR production has surpassed that of steam injection. In Brazil, the installation of a petrochemical complex in the Northeast of Brazil (Bahia State) offers opportunities for the injection of gases in the fields located in the Recôncavo Basin. Field-scale gas injection applications have almost always been associated with design and operational difficulties. The mobility ratio, which controls the volumetric sweep, between the injected gas and displaced oil bank in gas processes, is typically unfavorable due to the relatively low viscosity of the injected gas. Furthermore, the difference between their densities results in severe gravity segregation of fluids in the reservoirs, consequently leading to poor control in the volumetric sweep. Nowadays, from the above applications of gas injection, the WAG process is most popular. However, in attempting to solve the mobility problems, the WAG process gives rise to other problems associated with increased water saturation in the reservoir including diminished gas injectivity and increased competition to the flow of oil. The low field performance of WAG floods with oil recoveries in the range of 5-10% is a clear indication of these problems. In order to find na effective alternative to WAG, the Gas Assisted Gravity Drainage (GAGD) was developed. This process is designed to take advantage of gravity force to allow vertical segregation between the injected CO2 and reservoir crude oil due to their density difference. This process consists of placing horizontal producers near the bottom of the pay zone and injecting gás through existing vertical wells in field. Homogeneous models were used in this work which can be extrapolated to commercial application for fields located in the Northeast of Brazil. The simulations were performed in a CMG simulator, the STARS 2007.11, where some parameters and their interactions were analyzed. The results have shown that the CO2 injection in GAGD process increased significantly the rate and the final recovery of oil

Estudo paramétrico da injeção de vapor em reservatórios delgados

Exploration of heavy oil reservoirs is increasing every year in worldwide, because the discovery of light oil reservoirs is becoming increasingly rare. This fact has stimulated the research with the purpose of becoming viable, technically and economically, the exploration of such oil reserves. In Brazil, in special in the Northeast region, there is a large amount of heavy oil reservoir, where the recovery by the so called secondary methods Water injection or gas injection is inefficient or even impracticable in some reservoirs with high viscosity oils (heavy oils). In this scenario, steam injection appears as an interesting alternative for recover of these kinds of oil reservoirs. Its main mechanism consists of oil viscosity reduction through steam injection, increasing reservoir temperature. This work presents a parametric simulation study of some operational and reservoir variables that had influence on oil recovery in thin reservoirs typically found in Brazilian Northeast Basins, that use the steam injection as improved oil recovery method. To carry out simulations, it was used the commercial software STARS (Steam, Thermal, and Advanced Processes Reservoir Simulator) from CMG (Computer Modeling Group) version 2007.11. Reservoirs variables studied were horizontal permeability, vertical and horizontal permeability ratio, water zone and pay zone thickness ratio, pay zone thickness and thermal conductivity of the rock. Whereas, operational parameters studied were distance between wells and steam injection rate. Results showed that reservoir variables that had more influence on oil recovery were horizontal permeability and water zone and pay zone thickness ratio. In relation to operational variables, results showed that short distances between wells and low steam injection rates improved oil recovery

Estudo paramétrico da recuperação de petróleo pesado por aquecimento eletromagnético resistivo

Electrical resistive heating (ERH) is a thermal method used to improve oil recovery. It can increase oil rate and oil recovery due to temperature increase caused by electrical current passage through oil zone. ERH has some advantage compared with well-known thermal methods such as continuous steam flood, presenting low-water production. This method can be applied to reservoirs with different characteristics and initial reservoir conditions. Commercial software was used to test several cases using a semi-synthetic homogeneous reservoir with some characteristics as found in northeast Brazilian basins. It was realized a sensitivity analysis of some reservoir parameters, such as: oil zone, aquifer presence, gas cap presence and oil saturation on oil recovery and energy consumption. Then it was tested several cases studying the electrical variables considered more important in the process, such as: voltage, electrical configurations and electrodes positions. Energy optimization by electrodes voltage levels changes and electrical settings modify the intensity and the electrical current distribution in oil zone and, consequently, their influences in reservoir temperature reached at some regions. Results show which reservoir parameters were significant in order to improve oil recovery and energy requirement in for each reservoir. Most significant parameters on oil recovery and electrical energy delivered were oil thickness, presence of aquifer, presence of gas cap, voltage, electrical configuration and electrodes positions. Factors such as: connate water, water salinity and relative permeability to water at irreducible oil saturation had low influence on oil recovery but had some influence in energy requirements. It was possible to optimize energy consumption and oil recovery by electrical variables. Energy requirements can decrease by changing electrodes voltages during the process. This application can be extended to heavy oil reservoirs of high depth, such as offshore fields, where nowadays it is not applicable any conventional thermal process such as steam flooding

Estudo paramétrico do processo de injeção de solventes em poços horizontais para reservatórios de óleos pesados

The world has many types of oil that have a range of values of density and viscosity, these are characteristics to identify whether an oil is light, heavy or even ultraheavy. The occurrence of heavy oil has increased significantly and pointing to a need for greater investment in the exploitation of deposits and therefore new methods to recover that oil. There are economic forecasts that by 2025, the heavy oil will be the main source of fossil energy in the world. One such method is the use of solvent vaporized VAPEX which is known as a recovery method which consists of two horizontal wells parallel to each other, with a gun and another producer, which uses as an injection solvent that is vaporized in order to reduce the viscosity of oil or bitumen, facilitating the flow to the producing well. This method was proposed by Dr. Roger Butler, in 1991. The importance of this study is to analyze how the influence some operational reservoir and parameters are important in the process VAPEX, such as accumulation of oil produced in the recovery factor in flow injection and production rate. Parameters such as flow injection, spacing between wells, type of solvent to be injected, vertical permeability and oil viscosity were addressed in this study. The results showed that the oil viscosity is the parameter that showed statistically significant influence, then the choice of Heptane solvent to be injected showed a greater recovery of oil compared to other solvents chosen, considering the spacing between the wells was shown that for a greater distance between the wells to produce more oil

Estudo do comportamento de um solo mole tratado com cal, visando seu uso em fundações superficiais

Neste trabalho foi analisada a melhoria nas características de um solo mole quando tratado com cal, bem como a viabilidade técnica de se utilizar este novo material como uma camada suporte de fundações superficiais. O solo estudado classifica-se pedologicamente como Gley Húmico e a jazida localiza-se no município de Canoas/RS, às margens da BR 386. O trabalho teve as seguintes finalidades: realizar um estudo da influência dos diferentes teores de cal sobre as características tensão x deformação do solo tratado; verificar o ganho de resistência com o tempo de cura; modelar o comportamerito tensão x deformação do material tratado; realizar simulações numéricas, através do Método dos Elementos Finitos, do comportamento carga x recalque de fundações continuas flexíveis assentes sobre o novo material. Adotou-se o teor ótimo de cal (obtido pelo método de Eades & Grim, 1966) de 9% e dois valores inferiores de 7% e 5%. Realizaram-se os seguintes ensaios sobre o solo natural e as misturas de solo-cal: limites de Atterberg, compactação, granulometria, difratograma de raio X, permeabilidade (triaxial) e ensaios triaxiais adensados não drenados(CIU). Todos os ensaios foram realizados para três tempos de cura (7, 28 e 90 dias) e os corpos de prova foram curados em câmara úmida. Para modelar o comportamento tensão x deformação do solo melhorado, adotou-se o Modelo Hiperbólico e para o solo natural o Modelo Cam-Clay Modificado. O Modelo Hiperbólico foi implementado no software CRISPSO, desenvolvido na Universidade de Cambridge, Inglaterra. O software foi utilizado em um estudo paramétrico para determinar a influência do processo de estabilização no comportamento carga x recalque de fundações superficiais. Dos resultados obtidos, concluiu-se: que o método de Eades & Grim (1966) não mostrou-se adequado para determinação do teor ótimo de cal; houve, de maneira geral, melhora nas características físicas com o tratamento com cal; não houve ganho de resistência com o tempo de cura; o modelo hiperbólico representou bem o comportamento das misturas de solo cal e a colocação de uma camada de solo tratado apresenta melhoras no comportamento carga x recalque de fundações superficiais contínuas flexíveis.

Estudo crítico das metodologias de cálculo para perfis dobrados a frio de vigas tipo canal sem enrijecedores de borda

Neste trabalho é realizada uma análise crítica sobre as formas de dimensionamento de estruturas de chapa dobrada, apresentando as metodologias utilizadas pelas principais normas modernas de cálculo, juntamente com metodologias não convencionais. Para realizar dita análise concentrou se a atenção num tipo de perfil simples (perfis não enrijecidos), e submetido a dois tipos de carregamento: carga axial concentrada no centro de gravidade; barra trabalhando como viga em balanço com carga aplicada no centro de corte. Foi realizado um estudo comparativo, entre as normas de cálculo NBR 14762, AISI e Eurocode 3, com outros métodos de dimensionamento, que são: o método direto desenvolvido por Schafer (1997); e duas formulações de análise por elementos finitos: uma considerando a carga de flambagem elástica; e outra empregando uma análise não linear física e geométrica, para perfis submetidos à compressão centrada e à flexão. Neste trabalho realizou-se um estudo paramétrico, registrando em gráficos e tabelas a influência de parâmetros tais como: comprimento do elemento analisado; da relação entre a alma e a mesa; da relação alma e a espessura. Através destes gráficos é possível observar as diversas formas de colapso (flambagem local, flambagem global, colapso plástico entre outras) se apresentando como críticas e interagindo entre si. Realizaram-se também dois experimentos de perfis submetidos à flexão, com o objetivo de verificar a grandeza dos valores obtidos através das diversas metodologias de cálculo. Para aplicação prática dos conceitos e métodos apresentados fez-se a verificação do dimensionamento de uma estrutura utilizada como prateleira em um almoxarifado de uma empresa metalúrgica situada na grande Porto Alegre, a qual apresentou flambagem lateral de seus elementos horizontais.