Characteristics of the double-torsion test to determine the R-curve of ceramic materials

Double-torsion tests were carried out on a commercial ceramic floor tile to verify whether this test is suitable for determining the R-curve of ceramics. The instantaneous crack length was obtained by means of compliance calibration, and it was found that the experimental compliance underestimates the real crack length. The load vs. displacement curves were also found to drop after maximum loading, causing the stress intensity factor to decline. The R-curves were calculated by two methods: linear elastic fracture mechanics and the energetic method. It was obtained that the average values of crack resistance, R, and the double of the work of fracture, 2 · γwof, did not depend on notch length, a0, which is a highly relevant finding, indicating that these parameters were less dependent on the test specimen's geometry. The proposal was to use small notches, which produce long stable crack propagation paths that in turn are particularly important in the case of coarse microstructures.

Analytical model for the prediction of wrinkling of rear pressure bulkheads

In Airbus GmbH (Hamburg) has been developed a new design of Rear Pressure Bulkhead (RPB) for the A320-family. The new model has been formed with vacuum forming technology. During this process the wrinkling phenomenon occurs. In this thesis is described an analytical model for prediction of wrinkling based on the energetic method of Timoshenko. Large deflection theory has been used for analyze two cases of study: a simply supported circular thin plate stamped by a spherical punch and a simply supported circular thin plate formed with vacuum forming technique. If the edges are free to displace radially, thin plates will develop radial wrinkles near the edge at a central deflection approximately equal to four plate thicknesses w0/ℎ≈4 if they’re stamped by a spherical punch and w0/ℎ≈3 if they’re formed with vacuum forming technique. Initially, there are four symmetrical wrinkles, but the number increases if the central deflection is increased. By using experimental results, the “Snaptrhough” phenomenon is described.

Forest resources in Graciosa Island (Azores) : biomass availability for sustainable energetic use

Dissertação de Mestrado em Ambiente, Saúde e Segurança.

Forecasting the Earth"s radiation belts and modeling solar energetic particle events: Recent results from SPACECAST

High-energy charged particles in the van Allen radiation belts and in solar energetic particle events can damage satellites on orbit leading to malfunctions and loss of satellite service. Here we describe some recent results from the SPACECAST project on modelling and forecasting the radiation belts, and modelling solar energetic particle events. We describe the SPACECAST forecasting system that uses physical models that include wave-particle interactions to forecast the electron radiation belts up to 3 h ahead. We show that the forecasts were able to reproduce the >2 MeV electron flux at GOES 13 during the moderate storm of 7-8 October 2012, and the period following a fast solar wind stream on 25-26 October 2012 to within a factor of 5 or so. At lower energies of 10- a few 100 keV we show that the electron flux at geostationary orbit depends sensitively on the high-energy tail of the source distribution near 10 RE on the nightside of the Earth, and that the source is best represented by a kappa distribution. We present a new model of whistler mode chorus determined from multiple satellite measurements which shows that the effects of wave-particle interactions beyond geostationary orbit are likely to be very significant. We also present radial diffusion coefficients calculated from satellite data at geostationary orbit which vary with Kp by over four orders of magnitude. We describe a new automated method to determine the position at the shock that is magnetically connected to the Earth for modelling solar energetic particle events and which takes into account entropy, and predict the form of the mean free path in the foreshock, and particle injection efficiency at the shock from analytical theory which can be tested in simulations.

Forecasting the Earth"s radiation belts and modeling solar energetic particle events: Recent results from SPACECAST

High-energy charged particles in the van Allen radiation belts and in solar energetic particle events can damage satellites on orbit leading to malfunctions and loss of satellite service. Here we describe some recent results from the SPACECAST project on modelling and forecasting the radiation belts, and modelling solar energetic particle events. We describe the SPACECAST forecasting system that uses physical models that include wave-particle interactions to forecast the electron radiation belts up to 3 h ahead. We show that the forecasts were able to reproduce the >2 MeV electron flux at GOES 13 during the moderate storm of 7-8 October 2012, and the period following a fast solar wind stream on 25-26 October 2012 to within a factor of 5 or so. At lower energies of 10- a few 100 keV we show that the electron flux at geostationary orbit depends sensitively on the high-energy tail of the source distribution near 10 RE on the nightside of the Earth, and that the source is best represented by a kappa distribution. We present a new model of whistler mode chorus determined from multiple satellite measurements which shows that the effects of wave-particle interactions beyond geostationary orbit are likely to be very significant. We also present radial diffusion coefficients calculated from satellite data at geostationary orbit which vary with Kp by over four orders of magnitude. We describe a new automated method to determine the position at the shock that is magnetically connected to the Earth for modelling solar energetic particle events and which takes into account entropy, and predict the form of the mean free path in the foreshock, and particle injection efficiency at the shock from analytical theory which can be tested in simulations.

Determination of the HMX and RDX content in synthesized energetic material by HPLC, FT-MIR, and FT-NIR spectroscopies

A new method has been developed for determining the content of mixtures of octahydro-1,3,5,7-tetranitro-1,3,5,7-tetrazocine (HMX) and hexahydro-1,3,5-trinitro-1,3,5-triazine (RDX), the HMX/RDX ratio, in explosive compositions by Fourier transform infrared spectroscopy (FT-IR), in the regions MIR (mid infrared) and NIR (near infrared) with reference values obtained by chromatographic analysis (HPLC). Plots of relative MIR (A917 / A783) or NIR absorbance values (A4412 / A4317) versus HMX/RDX ratio determined by HPLC analysis revealed good linear relationships.

Optimization of wind blade design including its energetic characteristics

The goal of the Master’s thesis is to develop and to analyze the optimization method for finding a geometry shape of classical horizontal wind turbine blades based on set of criteria. The thesis develops a technique that allows the designer to determine the weight of such factors as power coefficient, sound pressure level and the cost function in the overall process of blade shape optimization. The optimization technique applies the Desirability function. It was never used before in that kind of technical problems, and in this sense it can claim to originality of research. To do the analysis and the optimization processes more convenient the software application was developed.

A survey of gradual solar energetic particle events

We develop a database of 110 gradual solar energetic particle (SEP) events, over the period 1967–2006, providing estimates of event onset, duration, fluence, and peak flux for protons of energy E > 60 MeV. The database is established mainly from the energetic proton flux data distributed in the OMNI 2 data set; however, we also utilize the McMurdo neutron monitor and the energetic proton flux from GOES missions. To aid the development of the gradual SEP database, we establish a method with which the homogeneity of the energetic proton flux record is improved. A comparison between other SEP databases and the database developed here is presented which discusses the different algorithms used to define an event. Furthermore, we investigate the variation of gradual SEP occurrence and fluence with solar cycle phase, sunspot number (SSN), and interplanetary magnetic field intensity (Bmag) over solar cycles 20–23. We find that the occurrence and fluence of SEP events vary with the solar cycle phase. Correspondingly, we find a positive correlation between SEP occurrence and solar activity as determined by SSN and Bmag, while the mean fluence in individual events decreases with the same measures of solar activity. Therefore, although the number of events decreases when solar activity is low, the events that do occur at such times have higher fluence. Thus, large events such as the “Carrington flare” may be more likely at lower levels of solar activity. These results are discussed in the context of other similar investigations.

Analytical method for the design of a machine with aligned and skewed permanent magnets

This work aims to present the design and the evaluation of a standard multi-pole machine with permanent magnets inserted in the rotor by two different geometrical forms: aligned and skewed magnets. The design (new analytical method) was based on a standard 250 W three phase 12-pole induction motor (squirrel cage rotor type), beginning with the original stator constructive data to calculate the magnetic flux density to determine the permanent magnets. In the development of the work, a simple and modular rotor was built reusing the original 12-pole stator (concentrated windings). The machine was evaluated in a laboratory for the purpose of checking the quantity and quality of energy produced with the machine operating as a generator and its start, torque, and performance working as a motor. In conclusion, the modular skewed magnet is an option for electrical machines, for the generation of a reasonable quality, in the context of decentralized generation and a motor with high torque and low energetic consumption.

A bankable method for the field testingor a CPV plant

The bankability of CPV projects is an important issue to pave the way toward a swift and sustained growth in this technology. The bankability of a PV plant is generally addressed through the modeling of its energy yield under a b aseline loss scenario, followed by an on-site measurement campaign aimed at verifying its energetic behavior. The main difference between PV and CPV resides in the proper CPV modules, in particular in the inclusion of optical lements and III-V multijunction cells that are much more sensitive to spectral variations than xSi cells, while the rest of the system behaves in a way that possesses many common points with xSi technology. The modeling of the DC power output of a CPV system thus requires several impo rtant second order parameters to be considered, mainly related to optics, spectral direct solar radiation, wind speed, tracker accuracy and heat dissipation of cells.

An accurate model for simulating energetic behavior of PV grid connected inverters

This paper proposes a new model for characterizing the energetic behavior of grid connected PV inverters. The model has been obtained from a detailed study of main loss processes in small size PV inverters in the market. The main advantage of the used method is to obtain a model that comprises two antagonistic features, since both are simple, easy to compute and apply, and accurate. One of the main features of this model is how it handles the maximum power point tracking (MPPT) and the efficiency: in both parts the model uses the same approach and it is achieved by two resistive elements which simulate the losses inherent to each parameter. This makes this model easy to implement, compact and refined. The model presented here also includes other parameters, such as start threshold, standby consumption and islanding behavior. In order to validate the model, the values of all the parameters listed above have been obtained and adjusted using field measurements for several commercial inverters, and the behavior of the model applied to a particular inverter has been compared with real data under different working conditions, taken from a facility located in Madrid. The results show a good fit between the model values and the real data. As an example, the model has been implemented in PSPICE electronic simulator, and this approach has been used to teach grid-connected PV systems. The use of this model for the maintenance of working PV facilities is also shown.

Artefactos energéticos : de Fuller a Piñero (1961-1972) = Energetic artefacts : from Fuller to Piñero (1961-1972)

La obra de Emilio Pérez Piñero que se desarrolla entre los años 1961 y 1972 año en el que muere en un accidente de tráfico volviendo de Figueras, se centra principalmente en artefactos desplegables y desmontables, ejecutando prototipos que en el presente trabajo se han dividido en dos grupos; la cúpula reticular y la infraestructura. No pudo por tanto acudir al Congreso de 1972 de la UIA a recoger el premio Auguste Perret a la innovación tecnológica, que en años anteriores habían recibido Félix Candela, Jean Prouvé, Hans Scharoun o Frei Otto, y que en aquella ocasión tuvo que recoger su viuda. Parámetros como el de la movilidad, indeterminación, intercambiabilidad, obsolescencia y otros que se analizan en el presente trabajo, aparecen a lo largo de toda su obra ya que muchos de sus artefactos están ubicados en no-lugares y tienen un carácter itinerante y por tanto se hace indispensable su rápido montaje y desmontaje, que unas veces se resuelve mediante la desmontabilidad y otras con la plegabilidad de éstos. Aunque pueda parecer Piñero una figura autárquica, lo cierto es que durante la década donde concentra su trabajo se produce una explosión en torno a al arquetipo que será denominado de forma genérica `artefacto´, ligado conceptualmente a los parámetros que aquí se definen. Entendemos artefacto como objeto material realizado por una o varias personas para cumplir una función, es sinónimo de máquina y aparato y deriva de las palabras latinas ars o artis (técnica) y facto (hecho), para designar a los objetos cuya fabricación requiere alguna destreza. El término latino `ars´ engloba a las técnicas y a las artes, lo que no ocurre con el término castellano arte que deriva de él. Los movimientos utópicos que comparte la década con Piñero, utilizan el arquetipo infraestructural, ligero y high tech, para a través de una arquitectura más ligada a la ciencia ficción, realizar una crítica al Movimiento Moderno institucionalizado, todos ellos comparten cierta obsesión por la movilidad, ligada ésta a la idea de espacio flexible, dinámico, nómada. Este concepto de neo-nomadismo, que representa un habitar dinámico, aglutina las nuevas formas de vivir donde la movilidad social y geográfica son habituales. El nomadismo, por otra parte se entiende como sinónimo de democracia y libertad. La arquitectura pasa de ser pesada, estática, permanente a ser un elemento dinámico en continuo movimiento. A veces con connotaciones biológicas se asimilan los artefactos a organismos vivos y les confieren dichas propiedades de crecimiento y autonomía energética, acumulándose en torno a megaestructuras, donde quedan `enchufados´. En este intento de dotar movilidad a lo inmueble, se buscan estructuras vivas y modificables que crecen en una asimilación de las leyes naturales utilizando los parámetros de metamorfosis, simbiosis y cambio. Estos movimientos de vanguardia tienen también ciertas connotaciones políticas y sociales basadas en la libertad y la movilidad y reniegan del consumismo institucionalizado, de la arquitectura como instrumento de consumo, como objeto de usar en la cultura de masas. El carácter político de la autogestión, de la customización como parámetro proyectual, de la autosuficiencia energética, que anticipa la llegada de la crisis energética del año 1973. Objeto de este trabajo será relacionar los conceptos que aparecen fuertemente en el entorno de la década de los años sesenta del siglo XX, en el trabajo de Emilio Pérez Piñero. Parámetros encontrados como conceptos en los grupos de vanguardia y utopía a su vez fuertemente influenciados por las figuras del ingeniero Richard Buckminster Fuller y del arquitecto Konrad Wachsmann. Se analizará que posible influencia tiene la obra de Fuller, principalmente el prototipo denominado cúpula reticular, en la obra de Pérez Piñero y sus coetáneos analizando sus pensamientos teóricos en torno a parámetros como la energía, principalmente en las teorías relativas a Synergetics. El término inventado por Richard B. Fuller es una contracción de otro más largo que en inglés agrupa tres palabras; synergetic-energetic geometry. La definición de sinergia es la cooperación, es decir es el resultado de la acción conjunta de dos o más causas, pero con un efecto superior a la suma de estas causas. El segundo término, energetics geometry, que traducido sería geometría energética hace referencia en primer lugar a la geometría; ya que desarrolla el sistema de referencia que utiliza la naturaleza para construir sus sistemas y en segundo lugar a la energía; ya que además debe ser el sistema que establezca las relaciones más económicas utilizando el mínimo de energía. Por otro lado se analiza la repercusión del prototipo denominado Infraestructura, término acuñado por Yona Friedman y basado estructuralmente y conceptualmente en los desarrollos sobre grandes estructuras de Konrad Wachsmann. El arquitecto alemán divulga su conocimiento en seminarios impartidos por todo el mundo como el que imparte en Tokio y se denomina Wachsmann´s Seminar donde participan algunos de los componentes del grupo Metabolista que sorprenderán al mundo con sus realizaciones en la exposición de Osaka de 1970. El intervalo temporal entre 1961 hasta 1972 hace referencia a la horquilla donde Pérez Piñero realiza su obra arquitectónica, que comienza en 1961 cuando gana el concurso convocado en Londres por la UIA (Unión Internacional de Arquitectos) con el proyecto conocido como Teatro Ambulante, hasta 1972 que es cuando fallece volviendo de Figueras donde está realizando dos encargos de Salvador Dalí; la cubrición del escenario del futuro Teatro-Museo Salvador Dalí y la Vidriera Hipercúbica que debía cerrar la boca de tal escenario. Bajo el título de `Artefactos energéticos. De Fuller a Piñero (1961-1972)´, se presenta esta Tesis doctoral, que tiene la intención de vincular la obra de Emilio Pérez Piñero con la de las neo vanguardias producidas por una serie de arquitectos que operan en el ámbito internacional. Estas vinculaciones se producen de una forma general, donde a través de una serie de estrategias según la metodología que posteriormente se describe se buscan relaciones de la obra del autor español con algunos de los movimientos más significativos que aparecen en dicha década y de manera específica estableciendo relaciones con las obras y pensamientos de los autores que pertenecen a estos movimientos y donde estas relaciones se hacen más evidentes. El objeto del presente trabajo es analizar y explicar la obra del arquitecto Emilio Pérez Piñero, que espacialmente se localiza en el territorio español, desde el punto de vista de estos movimientos para posteriormente poder determinar si existen puntos en común y si el arquitecto español no solo comparte la década temporalmente sino también conceptualmente y por tanto utiliza el ideario que utilizan sus coetáneos que forman parte de las neovanguardias de los años sesenta de siglo XX. ABSTRACT ABSTRACT The Work of Emilio Perez Piñero was developed between the years 1961 and 1972 when he died in a car accident coming back from Figueres, where he was building a geodesic dome to close the building that enclose the Dali’s museum. All his Work is mainly centered in artifact that could be collapsible and removable, taking the two prototypes that are described in this work as a recurrent element in all his creation. These are the reticular dome and the infrastructure that are very influenced by the work from Richard B. Fuller and Konrad Wachsmann. Emilio Pérez Piñero could not receive the Auguste Perret Prize in 1972 awarded by the UIA that years before have received architects as Felix Candela, Jean Prouvé, Hans Scharoun or Frei Otto, and this time Pérez Piñero´s wife will accept it because of his death. Parameters like mobility, changeability, expendability, indetermination and others appear currently in his Work. All the inventions that Piñero had been patented and all of the artifacts that he created are usually located in no-places, because they do have a shifting identity. This kind of building has to be quickly set on site, and this problem has to be solved in term of foldability or demounting. In the decade where his work focuses, an explosion has occurred around this archetype to be generally called artifact that is usually linked to mobility. We understand artifact as a material object made by one or more people to work in a particular way. It is sometimes equated with the terms machinery and apparatus and it is derived from the Latin word `ars´ or `artis´, what means techniques and `facto´ (fact). And we use this term to refer to objects whose manufacture requires the same skill, in fact the Latin word `ars´ covers the techniques and arts, which does not occur with the Castillan term `arte´ that derives from it and means only art. The term neo-nomadic is a relatively new name used for a dynamic life, commonly referred to new forms of life where social and geographical mobility are common. On the other hand nomadic could be understood as a synonymous for democracy and freedom. The architecture is not going to be hard and static anymore but a dynamic element in the move. The Neo-avant-garde movement that shares the decade with Piñero uses this infrastructural archetype, which is light and high-tech, to criticize the institutionalized Modern Movement through architecture linked to science fiction. They all share an obsession with mobility, a concept that is connected to the terms `dynamic´, `nomadic´, `flexibile´, etc. Sometimes, with biological connotations, the utopian assimilate the artifacts to living organisms and give them these properties of growth and energy autonomy, and they apparently grow around megastructures where they are plugged. In this attempt to provide mobility to the inertness, living structures and possibility of change are sought in order to make them grow like a living organism and to assimilate the natural laws of growth. According to a definition from architecture provided by Fernández- Galiano who calls it `exosomatic artifact´, he understand architecture as artifact of the human environment that regulates natural energy flows and channels the energy stored in fuels for the benefit of living beings that inhabit. It is also true that during the sixties a new environmental awareness in public opinion is formed and that is due to the exploitation and disproportionate use of energy resources, acceleration of technological processes and mass consumption. Consequently a new concept is born: energy autonomy, it is very close to rational use of natural energy. Such a concept will be culturally assimilated with the requirement of independence not only in the management but also in the building construction until we arrive at energy autonomy. The individuals become energy consumer, which in turn can enter the energy produced in the system to `life in an eco-mode way´. The objectives of this research are analyzing all of these parameters and concepts that are coming into view in the surrounding of the decade and relate them with the Work of Pérez Piñero. Terms strongly present in the avant-garde movements around the decade, a young architect’s generation strongly influenced by Richard B. Fuller and Konrad Wachsmann. However, it will be analyzed how important the influence of Buckminster Fuller's Work was and his theoretical text about energy on the Work of Pérez Piñero and his fellows of the decade. The term Synergetic was invented by Fuller and came from the words synergy and energetic geometry. Synergy is the cooperation or interaction of two or more agents to produce a greater effect than the sum of their separate effects. Energetic geometry is related to the geometries that the Nature is using to build their construction but always using low energy consumption. On the other hand, the influences from Wachsmann around the prototype called Infrastructure have been analyzed. The German architect has developed knowledge around huge structures that he has spread all around the world through seminars that he has been conducted. One of these was the Wachsmann´s seminar in Tokyo, where same of the members of the Metabolist group were taking part of. Later these young architects will surprise the world with his artifacts at the World Exposition in Osaka in 1970. Between 1961 and 1972 Pérez Piñero produced his architectural work. It began in 1961 when he received the first prize with his project Mobile Theatre in the competition organized by the UIA in London. In 1972 the Auguste Perret Prize was granted by the UIA too. He could not accept it because he died before in a car accident when he was coming from Figueres, when he was designing two projects for Dali. With the title `Energetic Artifacts. From Fuller to Piñero (1961- 1972)´, this thesis relates the Work of Emilio Pérez Piñero with the neo avant-garde made by a young architects’ generation who is sharing the time with him. Several strategies have been used to formed relationships between them. They are described in the present work to set up a method that allows us to relate the work and ideas of the architects of the neo avant-garde with the ones from Piñero. This work is intended to analyze and explained the work of Pérez Piñero from the point of view of the international architects’ generation who is operating at the same time and finally to determinate if Piñero is not sharing the time with them but the concepts, ideas and architectural parameters.

Energetic considerations of ciliary beating and the advantage of metachronal coordination

The internal mechanism of cilia is among the most ancient biological motors on an evolutionary scale. It produces beat patterns that consist of two phases: during the effective stroke, the cilium moves approximately as a straight rod, and during the recovery stroke, it rolls close to the surface in a tangential motion. It is commonly agreed that these two phases are designed for efficient functioning: the effective stroke encounters strong viscous resistance and generates thrust, whereas the recovery stroke returns the cilium to starting position while avoiding viscous resistance. Metachronal coordination between cilia, which occurs when many of them beat close to each other, is believed to be an autonomous result of the hydrodynamical interactions in the system. Qualitatively, metachronism is perceived as a way for reducing the energy expenditure required for beating. This paper presents a quantitative study of the energy expenditure of beating cilia, and of the energetic significance of metachronism. We develop a method for computing the work done by model cilia that beat in a viscous fluid. We demonstrate that for a single cilium, beating in water, the mechanical work done during the effective stroke is approximately five times the amount of work done during the recovery stroke. Investigation of multicilia configurations shows that having neighboring cilia beat metachronally is energetically advantageous and perhaps even crucial for multiciliary functioning. Finally, the model is used to approximate the number of dynein arm attachments that are likely to occur during the effective and recovery strokes of a beat cycle, predicting that almost all of the available dynein arms should participate in generating the motion.

Application of density functional theory to analysis of energetic heterogeneity and pore size distribution of activated carbons

A new approach based on the nonlocal density functional theory to determine pore size distribution (PSD) of activated carbons and energetic heterogeneity of the pore wall is proposed. The energetic heterogeneity is modeled with an energy distribution function (EDF), describing the distribution of solid-fluid potential well depth (this distribution is a Dirac delta function for an energetic homogeneous surface). The approach allows simultaneous determining of the PSD (assuming slit shape) and EDF from nitrogen or argon isotherms at their respective boiling points by using a set of local isotherms calculated for a range of pore widths and solid-fluid potential well depths. It is found that the structure of the pore wall surface significantly differs from that of graphitized carbon black. This could be attributed to defects in the crystalline structure of the surface, active oxide centers, finite size of the pore walls (in either wall thickness or pore length), and so forth. Those factors depend on the precursor and the process of carbonization and activation and hence provide a fingerprint for each adsorbent. The approach allows very accurate correlation of the experimental adsorption isotherm and leads to PSDs that are simpler and more realistic than those obtained with the original nonlocal density functional theory.

Facile synthesis and proposed mechanism of α,ω‐oxetanyl-telechelic poly(3-nitratomethyl-3-methyl oxetane) by an SN2(i) nitrato displacement method in basic media

The synthesis of a novel heterocyclic–telechelic polymer, α,ω-oxetanyl-telechelic poly(3-nitratomethyl-3-methyl oxetane), is described. Infrared spectroscopy (IR), gel permeation chromatography (GPC), and nuclear magnetic resonance (NMR) spectroscopy have been used to confirm the successful synthesis, demonstrating the presence of the telechelic-oxetanyl moieties. Synthesis of the terminal functionalities has been achieved via displacement of nitrato groups, in a manner similar to that employed with other leaving groups such as azido, bromo, and nitro, initiated by nucleophiles. In the present case, displacement occurs on the ends of a nitrato-functionalized polymer driven by the formation of sodium nitrate, which is supported by the polar aprotic solvent N,N-dimethyl formamide. The formation of an alkoxide at the polymer chain ends is favored and allows internal back-biting to the nearest carbon bearing the nitrato group, intrinsically in an SN2(i) reaction, leading to α,ω-oxetanyl functionalization. The telechelic-oxetanyl moieties have the potential to be cross-linked by chemical (e.g., acidic) or radiative (e.g., ultraviolet) curing methods without the use of high temperatures, usually below 100°C. This type of material was designed for future use as a contraband simulant, whereby it would form the predominant constituent of elastomeric composites comprising rubbery polymer with small quantities of solids, typically crystals of contraband substances, such as explosives or narcotics. This method also provides an alternative approach to ring closure and synthesis of heterocycles.