Subsurface drip irrigation emitter spacing effects on soil water redistribution, corn yield and water productivity

Emitter spacings of 0.3 to 0.6 m are commonly used for subsurface drip irrigation (SDI) of corn on the deep, silt loam soils of the U.S. Great Plains. Subsurface drip irrigation emitter spacings of 0.3, 0.6, 0.9 and 1.2 m were examined for the resulting differences in soil water redistribution, corn grain yield, yield components, seasonal water use, and water productivity in a 4‐year field study (2005 through 2008) at the Kansas State University Northwest Research‐Extension Center, Colby, Kansas. The results indicate that there is increased preferential water movement along the dripline (parallel) as compared to perpendicular to the dripline and that this phenomenon partially compensates for wider emitter spacings in terms of soil water redistribution. Corn yield and water productivity (WP) were not significantly affected by the emitter spacing with application of a full irrigation regime

Subsurface drip irrigation emitter spacing effects on soil water redistribution, corn yield and water productivity

Emitter spacings of 0.3 to 0.6 m are commonly used for subsurface drip irrigation (SDI) of corn on the deep, silt loam soils of the U.S. Great Plains. Subsurface drip irrigation emitter spacings of 0.3, 0.6, 0.9 and 1.2 m were examined for the resulting differences in soil water redistribution, corn grain yield, yield components, seasonal water use, and water productivity in a 4‐year field study (2005 through 2008) at the Kansas State University Northwest Research‐Extension Center, Colby, Kansas. The results indicate that there is increased preferential water movement along the dripline (parallel) as compared to perpendicular to the dripline and that this phenomenon partially compensates for wider emitter spacings in terms of soil water redistribution. Corn yield and water productivity (WP) were not significantly affected by the emitter spacing with application of a full irrigation regime

Model to design drip hose lateral line using two spacing between emitters

The use of non-pressure compensating drip hose in horticultural and annual cycle fruits is growing in Brazil. In this case, the challenge for designers is getting longer lateral lines with high values of uniformity. The objective of this study was to develop a model to design longer lateral lines using non-pressure compensating drip hose. Using the developed model, the hypotheses to be evaluated were: a) the use of two different spacing between emitters in the same lateral line allows longer length; b) it is possible to get longer lateral lines using high values of pressure variation in the lateral lines since the distribution uniformity stays below allowable limits. A computer program was developed in Delphi based on the model developed and it is able to design lateral lines in level using non-pressure compensating drip hose. The input data are: desired distribution uniformity (DU); initial and final pressure in the lateral line; coefficients of relationship between emitter discharge and pressure head; hose internal diameter; pipe cross-sectional area with the dripper; and roughness coefficient for the Hazen-Williams equation. The program allows calculate the lateral line length with three possibilities: selecting two spacing between emitters and defining the exchange point; using two pre-established spacing between emitters and calculating the length of each section with different spacing; using one emitter spacing. Results showed that the use of two sections with different spacing between drippers in the lateral line didn't allow longer length but got better uniformity when compared with lateral line with one spacing between emitters. The adoption of two spacing increased the flow rate per meter in the final section which represented approximately 80% of the lateral line total length and this justifies their use. The software allowed DU above 90% with pressure head variation of 40% and the use of two spacing between emitters. The developed model/software showed to be accurate, easy to handle and useful for lateral line design using non-pressure compensating drip hose.

Uso de Dois Espaçamentos Entre Gotejadores na Mesma Linha Lateral e Seus Efeitos Sobre a Formação do Bulbo Molhado no Solo e Parâmetros Físicos de Rabanete

The use of irrigation systems that consume lower water and energy in agriculture is important to supply the growing global demand for food. In this way, it's important to develop techniques that will increase the uniformity of water application on drip irrigation systems. The aim of the work was to compare the provision of lateral lines in drip irrigation, through the formation of wet bulbs in soil and physical parameters of radish, composed of single spacing between drippers in relation to lateral lines composed of two segments, each one composed by different spacing between emitters. Two distributions of evaluation were carried out: 1) conventional drip lateral lines with 20 cm emitter spacing were compared to proposed drip lines, with 24 emitter spacing in the initial section and 20 cm emitter spacing in the final section; 2) conventional drip lateral lines with 30 cm emitter spacing were compared to proposed drip lines, with 36 emitter spacing in the initial section and 30 cm emitter spacing in the final section. The experiment was carried out in a greenhouse of the Sao Manuel Experimental Farm, located at Sao Manuel, SP. The experimental design was entirely randomized, with six treatments and four replications. Results showed no difference among treatments for the most of the evaluated variables. So it is possible to conclude that the use of different spacing between emitters in the same lateral line can be used to increase the line length.

Uso de dois espaçamentos entre gotejadores na mesma linha lateral e seus efeitos sobre a formação do bulbo molhado, produtividade e qualidade de rabanete (raphanus sativus L.)

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Estudo da uniformidade de emissão de água utilizando diferentes espaçamentos entre gotejadores na linha lateral

Pós-graduação em Agronomia (Irrigação e Drenagem) - FCA

Increasing the lateral line length of drip irrigation systems

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Respuesta fisiológica, productiva y cualitativa del cultivar Syrah (Vitis vinifera L) con diferentes frecuencias de riego y densidad de goteros en suelos arcillosos

La disponibilidad hídrica es uno de los principales factores que determinan el rendimiento del viñedo en muchas regiones vitícolas, por lo que sus consecuencias han sido ampliamente estudiadas. Sin embargo, para una cantidad de agua de riego determinada, otros aspectos como la frecuencia de aplicación, o la combinación entre el caudal de los goteros y la distancia entre los mismos (es decir, el patrón de distribución de agua en el suelo), pueden jugar un papel relevante, pero estos factores han sido poco estudiados. El objetivo de este trabajo ha sido evaluar las implicaciones agronómicas y fisiológicas de dos frecuencias de riego (IrrF, cada 2 y 4 días) y dos patrones de distribución de agua (DisP, goteros de 2 L h-1 separados 0,6 m vs. goteros de 4 L h-1 separados 1,2 m). El experimento se llevó a cabo durante cuatro temporadas consecutivas en un viñedo cv. Syrah con un suelo arcilloso en el centro de España, y los dos factores fueron evaluados bajo dos condiciones de disponibilidad hídrica (Baja: 20% de ETo y Media: 40% de ETo). El efecto de la frecuencia de riego y el patrón de distribución de agua en la respuesta agronómica del cv. Syrah se ha estudiado en el capítulo 1. La frecuencia de riego y el patrón de distribución de agua en el suelo afectaron a algunos aspectos de los componentes de rendimiento y desarrollo vegetativo en las dos condiciones de disponibilidad hídrica, aunque los efectos observados no fueron los mismos todos los años. Los efectos fueron más evidentes para IrrF en condiciones de baja disponibilidad hídrica y para DisP en condiciones de disponibilidad hídrica media. Dos de los cuatro años del experimento, el pasar de frecuencia de riego de 2 días a 4 días causó un incremento medio de rendimiento del 20% para la situación de baja disponibilidad hídrica. La textura del suelo, sin duda ha condicionado los resultados obtenidos en los tratamientos regados con el 20% de la ETo, ya que regar cada dos días implicaba la aplicación de pequeñas cantidades de agua y se formaban bulbos de riego superficiales, probablemente favoreciendo las pérdidas por evaporación. En el capítulo 2, se ha analizado el efecto de la frecuencia de riego y del patrón de distribución de agua en el estado hídrico de la planta y el intercambio gaseoso a nivel de hoja con el fin de explicar las diferencias observadas en la respuesta agronómica. En lo que respecta a la frecuencia de riego, en condiciones de baja disponibilidad hídrica, las plantas regadas cada 4 días (plantas 4d), mostraron mayores tasas de asimilación neta y conductancia estomática que las plantas regadas cada 2 días (plantas 2d), lo que es consistente con la hipótesis de que con la frecuencia de riego de 2 días se produjo una pérdida de eficiencia del uso del agua, probablemente debido a una mayor evaporación como consecuencia del hecho de que el volumen de suelo mojado creado era pequeño y cerca de la superficie. En condiciones de disponibilidad hídrica media, las diferencias en el intercambio gaseoso a nivel de hoja fueron mucho más pequeñas. Al comienzo del verano cada frecuencia de riego se comportó mejor uno de los días de medida, compensando al final del ciclo de riego de 4 días. Sin embargo, a medida que avanzó el verano y el déficit de agua se hizo más alto, las diferencias significativas aparecieron sólo en el 'día 4' del ciclo de riego, cuando las plantas 2d se comportaron mejor que las plantas regadas 4d que llevaban tres días sin regarse. Estas diferencias fisiológicas fueron menores que en condiciones de baja disponibilidad hídrica y al parecer no suficientes para afectar el comportamiento agronómico. En cuanto al patrón de distribución de agua, el efecto fue poco significativo, pero la mayor densidad de goteros tendió a presentar un mayor intercambio gaseoso a nivel de hoja, especialmente a media mañana. El efecto fue más importante para las condiciones de disponibilidad hídrica media. En el capítulo 3, se han comparado las relaciones entre el intercambio gaseoso a nivel de hoja, el estado hídrico y la demanda atmosférica, con el fin de explicar los cambios en la intensidad de la respuesta fisiológica observados en el Capítulo 2. No se han encontrado diferencias en dichas relaciones para el patrón de distribución de agua, por lo que sólo se ha analizado el efecto de la frecuencia de riego. El estudio se ha centrado fundamentalmente en si las plantas mostraron una respuesta fisiológica diferente a los cambios en el estado hídrico y en la demanda atmosférica según el tiempo transcurrido desde el último riego. Las diferencias observadas explican los resultados obtenidos en los capítulos anteriores, y sugieren la existencia de procesos de aclimatación vinculados a la frecuencia de riego y a la disponibilidad hídrica. Las plantas bajo condiciones de baja disponibilidad hídrica se mostraron más aclimatadas al estrés hídrico que aquellas en condiciones de disponibilidad hídrica media. La frecuencia de riego afectó claramente la relación entre los parámetros de intercambio gaseoso a nivel de hoja, el estado hídrico de la planta y las condiciones atmosféricas, y junto con la cantidad de agua aplicada tuvo implicaciones en el desarrollo de mecanismos de aclimatación que afectaron a la respuesta fisiológica de la planta, afectando a la eficiencia del riego. ABSTRACT Water availability is one of the major factors that determine vineyard performance in many grape growing regions, so its implications have been widely studied before. However, for a given irrigation water amount, other aspects such as application frequency, or emitter spacing and flow rate (i.e., distribution pattern), may play a relevant role, but these factors have been scarcely studied. The aim of this work was to evaluate the agronomic and physiological implications of two irrigation frequencies (IrrF, every 2 and 4 days) and two water distribution patterns (DisP, 2 L h−1 emitters every 0.6 m vs. 4 L h−1 emitters every 1.2 m). The experiment was carried out during four consecutive seasons in a cv. Syrah vineyard with a clay soil in central Spain, and the two factors were evaluated under two water availability conditions (LOW WA: 20% of ETo and MEDIUM WA: 40% of ETo). The effect of irrigation frequency and water distribution pattern on the agronomical response of cv. Syrah was studied in Chapter 1. IrrF and DisP affected some aspects of vegetative development and yield components under both water availability conditions, although the effects observed were not the same every year. The effects were more evident for IrrF under low water availability and for DisP under medium water availability. Two out of the four years of the experiment, the change of irrigation frequency from 2 days to 4 days promoted an average yield increase of 20% for the LOW WA situation. Soil texture certainly conditioned the results obtained under LOW WA conditions, since high frequency irrigation implied applying small amounts of water that resulted in limited superficial water bulbs, which probably favored water evaporation. In Chapter 2, the effect of irrigation frequency and water distribution pattern on plant water status and leaf gas exchange was analyzed to explain the differences observed in the agronomical response. Concerning irrigation frequency, under LOW WA conditions, applying irrigation every 4 days, resulted in higher net assimilation rates and stomatal conductance than doing it every 2 days, supporting the hypothesis that the latter frequency resulted in a water use efficiency loss, probably due to higher evaporation as a consequence of the fact the wetted soil volume created was small and close to the surface. Under MEDIUM WA conditions, differences in leaf gas exchange were much smaller. At the beginning of the summer each irrigation frequency behaved better one of the measurements days, compensating at the end of the 4-day irrigation cycle. However, as the summer progressed and water deficit became higher, significant differences appeared only on ‘day 4’ of the irrigation cycle, when 2d plants behaved better than 4d plants. These physiological differences were smaller than under LOW WA conditions and apparently not sufficient to affect agronomical performance. Regarding water distribution pattern, the effect was less significant but the closest emitter spacing resulted in general terms in a higher leaf gas exchange, especially at midmorning. The effect was more noticeable for MEDIUM WA conditions. In Chapter 3, the relationships between leaf gas exchange and leaf water status and atmospheric demand were compared to explain the changes in the intensity of the physiological response observed in Chapter 2. No differences were found in the relationships for water distribution pattern, so only the effect of irrigation frequency was analyzed focusing on whether the plants have a different physiological response to changes in water status and atmospheric demand according to the time elapsed since the last irrigation. Differences observed in the relationships explained the results obtained in the previous chapters, and point at the occurrence of acclimation processes linked to irrigation frequency and to water availability. Plants under LOW WATER AVAILABILITY conditions seemed to be more acclimated to water stress than those under MEDIUM WATER AVAILABILITY conditions. Irrigation frequency clearly affected the relationship between leaf gas exchange parameters, plant water status and atmospheric conditions, and together with the amount of water applied had implications in the development of acclimation mechanisms that affected plant physiological response, thus affecting irrigation efficiency.

Estimating water application efficiency for drip irrigation emitter patterns on banana

The objective of this work was to evaluate root and water distribution in irrigated banana (Musa sp.), in order to determine the water application efficiency for different drip irrigation emitter patterns. Three drip emitter patterns were studied: two 4-L h-1 emitters per plant (T1), four 4-L h-1 emitters per plant (T2), and five 4-L h-1 emitters per plant (T3). The emitters were placed in a lateral line. In the treatment T3, the emitters formed a continuous strip. The cultivated area used was planted with banana cultivar BRS Tropical, with a 3-m spacing between rows and a 2.5-m spacing between plants. Soil moisture and root length data were collected during the first production cycle at five radial distances and depths, in a 0.20x0.20 m vertical grid. The experiment was carried out in a sandy clay loam Xanthic Hapludox. Soil moisture data were collected every 10 min for a period of five days using TDR probes. Water application efficiency was of 83, 88 and 92% for the systems with two, four and five emitters per plant, respectively. It was verified that an increase in the number of emitters in the lateral line promoted better root distribution, higher water extraction, and less deep percolation losses.

Load Ratio Estimation Through Striation Height and Spacing Analysis of an Aerospace Al Alloy 7475-T7351

It is well known that striation spacing may be related to the crack growth rate, da/dN, through Paris equation, as well as the maximum and minimum loads under service loading conditions. These loads define the load ratio, R, and are considered impossible to be evaluated from the inter-spacing striations analysis. In this way, this study discusses the methodology proposed by Furukawa to evaluate the maximum and minimum loads based on the experimental fact that the relative height of a striation, H, and the striation spacing, s, are strongly influenced by the load ratio, R. Fatigue tests in C(T) specimens were conducted on SAE 7475-T7351 Al alloy plates at room temperature and the results showed a straightforward correlation between the parameters H, s, and R. Measurements of striation height, H, were performed using scanning electron microscopy and field emission gun (FEG) after sectioning the specimen at a large inclined angle to amplify the height of the striations. The results showed that for increasing R the values of H/s tend to increase. Striation height, striation spacing, and load ratio correlations were obtained, which allows one to estimate service loadings from fatigue fracture surface survey.

Possible states in the flow around two circular cylinders in tandem with separations in the vicinity of the drag inversion spacing

The possible states in the flow around two identical circular cylinders in tandem arrangements are investigated for configurations in the vicinity of the drag inversion separation. By means of numerical simulations, the hysteresis in the transition between the shedding regimes is studied and the relationship between (three-dimensional) secondary instabilities and shedding regime determination is addressed. The differences observed in the behavior of two- and three-dimensional flows are analyzed, and the regions of bistable flow are delimited. Very good agreement is found between the proposed scenario and results available in the literature. (C) 2010 American Institute of Physics. [doi: 10.1063/1.3420111]

Dendritic Arm Spacing Affecting Mechanical Properties and Wear Behavior of Al-Sn and Al-Si Alloys Directionally Solidified under Unsteady-State Conditions

Alloys of Al-Sn and Al-Si are widely used in tribological applications such as cylinder liners and journal bearings. Studies of the influence of the as-cast microstructures of these alloys on the final mechanical properties and wear resistance can be very useful for planning solidification conditions in order to permit a desired level of final properties to be achieved. The aim of the present study was to contribute to a better understanding about the relationship between the scale of the dendritic network and the corresponding mechanical properties and wear behavior. The Al-Sn (15 and 20 wt pct Sn) and Al-Si (3 and 5 wt pct Si) alloys were directionally solidified under unsteady-state heat flow conditions in water-cooled molds in order to permit samples with a wide range of dendritic spacings to be obtained. These samples were subjected to tensile and wear tests, and experimental quantitative expressions correlating the ultimate tensile strength (UTS), yield tensile strength, elongation, and wear volume to the primary dendritic arm spacing (DAS) have been determined. The wear resistance was shown to be significantly affected by the scale of primary dendrite arm spacing. For Al-Si alloys, the refinement of the dendritic array improved the wear resistance, while for the Al-Sn alloys, an opposite effect was observed, i.e., the increase in primary dendrite arm spacing improved the wear resistance. The effect of inverse segregation, which is observed for Al-Sn alloys, on the wear resistance is also discussed.

Technical and economical evaluation of a harvester, working under different spacing and planting arrangement conditions in eucalypts plantations

Plantation spacing selection has the primary objective of assigning each tree enough space for maximum growth and best quality to be attained with a minimum cost. From the harvest standpoint, an increase in stand density directly implies a decrease of individual tree volume, reducing also harvester productive capacity. The objective of this research is to assess the effects of several initial spacings and arrangements in eucalyptus plantations on production capacity, operational capacity and costs of forest harvester. Real operational data were collected from two eucalypt plantations at different initial spacing of 6.0, 7.5, 9.0, 12 and 18 m(2) per tree. Simulation data were obtained from a forest harvester simulator. Using spacing (E), mean tree volume (MV), diameter at breast height (DBH) and height (H) values, a stepwise regression test procedure was run, and correlations computed in order to measure their participation in operational capacity. Operational costs were computed with an accounting method proposed by FAO. Mean tree volume (MV) explained 88% of forest harvester operational capacity. Spacing (E) affected 8.5% of harvester operational capacity; wider spacings were related to higher individual tree volumes. Harvesting operation costs were lower in wider spaced treatments.

Spacing, population density and nitrogen fertilization in corn grown in an Oxisoil

The objective of this study was to evaluate yield components, leaf nitrogen content and grain yield in corn as affected by row spacing, plant density and nitrogen topdressing. The experiment was conducted with the single-cross hybrid AG 8021, in the municipality of Toledo-PR, in an Oxisoil under no-tillage system, in the crop year 2005/ 2006. The experiment was arranged in a randomized block design and treatments in split-split-plots, with four replications. The two row spacings (0.45 and 0.90 m) were allocated in the main plots, the two plant densities (60,000 and 80,000 plants ha-1) were allocated in the subplots and the three nitrogen rates (80, 100, 120 and 140 kg ha-1 N) were allocated in the sub-subplots. Topdress nitrogen was applied using urea as N source. The rise of the plant population from 60,000 to 80,000 plants ha-1 and the application of topdress nitrogen resulted in increased production components. The application of topdress fertilization provided increase in leaf N content and grain yield for the spacings 0.45 m and 0.90 m. Yield was higher in the spacing 0.45 m than 0.90 m. Yield was higher with 60,000 plants than with 80,000 plants at 0.90 m, while at 0.45 m there was no difference in relation to the plant density.

Effect of the acoustic impedance in ultrasonic emitter transducers using digital modulations

In an underwater environment it is difficult to implement solutions for wireless communications. The existing technologies using electromagnetic waves or lasers are not very efficient due to the large attenuation in the aquatic environment. Ultrasound reveals a lower attenuation, and thus has been used in underwater long-distance communications. The much slower speed of acoustic propagation in water (about 1500 m/s) compared with that of electromagnetic and optical waves, is another limiting factor for efficient communication and networking. For high data-rates and real-time applications it is necessary to use frequencies in the MHz range, allowing communication distances of hundreds of meters with a delay of milliseconds. To achieve this goal, it is necessary to develop ultrasound transducers able to work at high frequencies and wideband, with suitable responses to digital modulations. This work shows how the acoustic impedance influences the performance of an ultrasonic emitter transducer when digital modulations are used and operating at frequencies between 100 kHz and 1 MHz. The study includes a Finite Element Method (FEM) and a MATLAB/Simulink simulation with an experimental validation to evaluate two types of piezoelectric materials: one based on ceramics (high acoustic impedance) with a resonance design and the other based in polymer (low acoustic impedance) designed to optimize the performance when digital modulations are used. The transducers performance for Binary Amplitude Shift Keying (BASK), On-Off Keying (OOK), Binary Phase Shift Keying (BPSK) and Binary Frequency Shift Keying (BFSK) modulations with a 1 MHz carrier at 125 kbps baud rate are compared.