Desenvolvimento de embalagem biodegradável ativa a base de fécula de mandioca e agentes antimicrobianos naturais.

Aliado ao fato dos biomateriais ainda serem pouco explorados pelas indústrias alimentícias, este trabalho propôs o desenvolvimento de embalagens que sejam, além de biodegradáveis, também ativas através do uso de um agente antimicrobiano natural capaz de inibir a proliferação de fungos correntes em produtos de panificação (Penicillium commune e Eurotium amstelodami). Primeiramente, filmes biodegradáveis a base de fécula de mandioca foram elaborados pela técnica de casting, usando açúcares e glicerol como plastificantes. O aumento do conteúdo de glicerol causou diminuição da resistência máxima à tração e elevação dos valores de propriedades de barreira. Numa segunda etapa do trabalho, a introdução de nanopartículas de argila esmectita influenciou positivamente as propriedades de barreira dos filmes, devido à diminuição observada nos valores de permeabilidade ao vapor de água e coeficiente de permeabilidade ao oxigênio. Nesta fase, a variação do conteúdo de glicerol também afetou significativamente as propriedades mecânicas e de barreira dos filmes biodegradáveis. As concentrações inibitórias mínimas dos óleos essenciais de cravo e de canela contra os fungos estudados foram definidas e o óleo essencial de canela foi selecionado, para ser incorporado aos filmes biodegradáveis, em três conteúdos distintos, pois foi o composto que mostrou uma inibição mais eficiente. A atividade antimicrobiana dos filmes biodegradáveis com incorporação de óleo essencial de canela foi testada sobre os micro-organismos escolhidos através de testes de difusão em halo, cujos resultados foram suficientes para demonstrar o potencial ativo da embalagem desenvolvida. Como método alternativo de incorporação do agente antimicrobiano, gás carbônico (CO2) em estado supercrítico foi utilizado como solvente. Os resultados obtidos foram promissores, uma vez que se observou incorporação de agente antimicrobiano dentro da matriz polimérica em quantidade suficiente para inibir a proliferação dos fungos testados.

Avaliação energética e econômica da substituição de tubetes de plástico por tubetes biodegradáveis na produção de mudas de aroeira - Schinus terebinthifokius Raddi

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Características físicas de filmes biodegradáveis produzidos a partir de amidos modificados de mandioca

Amidos de mandioca podem ser matérias-primas para a obtenção de filmes biodegradáveis, sendo que para a formação destes é necessária a elaboração de suspensões filmogênicas. Alguns processos de modificação do amido podem torná-lo miscível em água fria, e outros processos de modificação podem alterar as propriedades dos filmes, tornando-os mais fortes e flexíveis. O objetivo deste trabalho foi verificar as características físicas de filmes biodegradáveis elaborados com amidos modificados de mandioca pelo processo de casting (desidratação de uma solução filmogênica sobre placas de Petri). Os amidos modificados utilizados foram: cross linked; carboximetilamido (CMA) de baixa viscosidade e alta viscosidade e esterificado. A viscosidade é fator importante para a elaboração da suspensão filmogênica e foi avaliada utilizando-se o equipamento Rapid Visco Analyser (RVA). Os filmes elaborados foram comparados a um filme de PVC comercial com espessura de 0,0208 a 0,0217 mm. Os amidos foram caracterizados por avaliação da composição físico-química, granulometria, microscopia eletrônica e viscosidade (Rapid Visco Analyser). A análise por microscopia eletrônica dos filmes ressaltou as diferenças entre os diferentes amidos utilizados. O RVA mostrou que, com exceção do cross linked, todos os amidos modificados apresentaram certa solubilidade a frio, o que facilita o preparo das soluções filmogênicas, entretanto, todos os amidos modificados apresentaram redução acentuada da tendência à retrogradação, propriedade geralmente associada à formação de filmes. As espessuras dos filmes de amido variaram de 0,0551 a 0,1279 mm, cujas espessuras mínimas foram a dos filmes de amido cross linked. Os filmes mostraram-se transparentes, manuseáveis e bem homogêneos. Não houve interferência da espessura na permeabilidade ao vapor d'água, e os filmes com 5% de matéria-seca, independente do tipo de amido modificado, foram mais permeáveis que o PVC. Porém, quando se compara o filme biodegradável de amidos modificados com o filme comercial de PVC, ainda há muito que se trabalhar na formulação para melhorar várias propriedades deste tipo de embalagem, que tem amplo uso atualmente.

Desenvolvimento de nova embalagem para comercialização, transporte e liberação do parasitoide Cotesia flavipes (Cameron, 1891) (Hymenoptera: Braconidae)

Pós-graduação em Agronomia (Entomologia Agrícola) - FCAV

Desenvolvimento e otimização de um filme biodegradável à base de proteína do tremoço (Lupinus angustifolius)

Dissertação de Mestrado, Biologia Molecular e Microbiana, Faculdade de Ciências e Tecnologia, Universidade do Algarve, 2015

Avaliação de danos mecânicos causados em banana Nanicão durante as etapas de beneficiamento, transporte e embalagem

This study had as objective the evaluation of mechanical damages occurred in banana Nanicão during the improvement process, packing and distribution, identifying the probable critical points. The mechanical damages caused by transport, first cleaning; cleanness and sorting; preservation in the packing, transport, and mature were evaluated. The studied packing had been: torito wooden packing (18 kg), wood type ½ box, (13 kg) and cardboard (18 kg). The stage of preservation and transport of the fruits to the distribution center duplicated the light defects and quintupled the serious defects, causing rottenness after the acclimatization. The cardboard packing did not support the piling up and presented deformations, that resulted in the kneading the fruits of the inferior packing, causing a significant increase of the serious defects. The fruits conditioned in the involved packing of plastic bubble had presented an inferior number of serious damages when compared with the others packing, without the plastic.

Influência da embalagem de polietileno de baixa densidade e da temperatura na conservação do repolho minimamente processado

This research studied the effect of low density polyethylene packaging and storage temperature on the preservation of fresh-cut (minimally processed) cabbage. The cabbages, previously cooled to a temperature of 10 ºC, were selected, washed, cut in four parts (with the central stalk removed), sanitized, cut in strips, rinsed, put in the centrifuge, weighed and stored in plastic packaging of low density polyethylene (70 µm), and then stored in cold chambers at temperatures of 1 and 10 ºC for 20 days. The following aspects were evaluated: carbon dioxide, oxygen and ethylene in the internal atmosphere of the package as well as, pH, titratable acidity, total soluble solids, vitamin C, loss of fresh mass and the total soluble solids/acidity in the fresh-cut cabbage ratio. The experimental design was entirely casual, with three repetitions. The analysis parameters, except for the vitamin C, loss of fresh mass and ethylene, presented significant variation between the temperatures and days of storage. The cabbage stored at a temperature of 1 ºC presented a shelf life of around 15 days, significantly higher than that stored at 10 ºC. At this temperature, on the 8th day of storage, the product was completely decayed, unfit for commercialization or consumption.

Effect of casting atmosphere on the shear bond strength of a ceramic to Ni-Cr and Ni-Cr-Be alloys

The success of metal-ceramic restorations depends on an optimal bond between metal and ceramic. This study evaluated the effect of 3 casting atmospheres on the metal-ceramic bond strength (MCBS) of 2 Ni-Cr alloys, with beryllium (Fit Cast V) and without beryllium (Fit Cast SB). Sixty acrylic resin patterns (8 mm long and 5 mm diameter) were obtained using a fluorocarbon resin matrix. Wax was used to refine the surface of acrylic resin patterns that were invested and cast in an induction casting machine under normal, vacuum, and argon atmospheres at a temperature of 1340ºC. The castings were divested manually and airborne-particle abraded with 100-µm aluminum-oxide. Ten castings were obtained for each group. The IPS Classic V ceramic was applied (2 mm high and 5 mm diameter). The shear bond strength was tested in a mechanical testing machine with a crosshead speed of 2.0 mm/min. The MCBS data (MPa) were subjected to 2-way analysis of variance (α=0.05). There was no statistically significant difference (p>0.05) between the alloys or among the casting atmospheres. Within the limitations of this study, it may be concluded that the presence of beryllium and the casting atmosphere did not interfere in the MCBS of the evaluated metal-ceramic combinations

Comparative study of two commercially pure titanium casting methods

The interest in using titanium to fabricate removable partial denture (RPD) frameworks has increased, but there are few studies evaluating the effects of casting methods on clasp behavior. OBJECTIVE: This study compared the occurrence of porosities and the retentive force of commercially pure titanium (CP Ti) and cobalt-chromium (Co-Cr) removable partial denture circumferential clasps cast by induction/centrifugation and plasma/vacuum-pressure. MATERIAL AND METHODS: 72 frameworks were cast from CP Ti (n=36) and Co-Cr alloy (n=36; control group). For each material, 18 frameworks were casted by electromagnetic induction and injected by centrifugation, whereas the other 18 were casted by plasma and injected by vacuum-pressure. For each casting method, three subgroups (n=6) were formed: 0.25 mm, 0.50 mm, and 0.75 mm undercuts. The specimens were radiographed and subjected to an insertion/removal test simulating 5 years of framework use. Data were analyzed by ANOVA and Tukey's to compare materials and cast methods (α=0.05). RESULTS: Three of 18 specimens of the induction/centrifugation group and 9 of 18 specimens of plasma/vacuum-pressure cast presented porosities, but only 1 and 7 specimens, respectively, were rejected for simulation test. For Co-Cr alloy, no defects were found. Comparing the casting methods, statistically significant differences (p<0.05) were observed only for the Co-Cr alloy with 0.25 mm and 0.50 mm undercuts. Significant differences were found for the 0.25 mm and 0.75 mm undercuts dependent on the material used. For the 0.50 mm undercut, significant differences were found when the materials were induction casted. CONCLUSION: Although both casting methods produced satisfactory CP Ti RPD frameworks, the occurrence of porosities was greater in the plasma/vacuum-pressure than in the induction/centrifugation method, the latter resulting in higher clasp rigidity, generating higher retention force values.

Microstructural characteristics and corrosion behavior of a super duplex stainless steel casting

The machining of super duplex stainless steel castings is usually complicated by the difficulty involved in maintaining the dimensional tolerances required for given applications. Internal stresses originating from the solidification process and from subsequent heat treatments reach levels that exceed the material`s yield strength, promoting plastic strain. Stress relief heat treatments at 520 degrees C for 2 h are an interesting option to solve this problem, but because these materials present a thermodynamically metastable condition, a few precautions should be taken. The main objective of this work was to demonstrate that, after solution annealing at 1130 degrees C and water quenching, stress relief at 520 degrees C for 2 h did not alter the duplex microstructure or impair the pitting corrosion resistance of ASTM A890/A890M Grade 6A steel. This finding was confirmed by microstructural characterization techniques, including light optical and scanning electron microscopy, and X-ray diffraction. Corrosion potential measurements in synthetic sea water containing 20,000 ppm of chloride ions were also conducted at three temperatures: 5 degrees C, 25 degrees C and 60 degrees C. (c) 2008 Elsevier Inc. All rights reserved.

Microstructure and texture assessment of Al-Mn-Fe-Si (3003) aluminum alloy produced by continuous and semicontinuous casting processes

Aluminum sheets are currently produced by the direct-chill process (DC). The need for low-cost aluminum sheets is a challenge for the development of new materials produced by the twin roll caster (TRC) process. It is expected that sheets produced from these different casting procedures will differ in their microstructure. These differences in microstructure and in the crystallographic texture have great impact on sheet mechanical properties and formability. The present study investigated microstructure and evaluated texture of two strips of Al-Mn-Fe-Si (3003) aluminum alloy produced by TRC and by hot-rolling processes. It was possible to notice that the microstructure, morphology, and grain size of the TRC sample were more homogenous than those found in hot-rolled samples. Both strips, obtained by the two processes, showed strong texture gradient across the thickness.

Rheological behaviour of the mushy zone and its effect on the formation of casting defects during solidification

A new conceptual framework has been developed which explains the formation of shear-related casting defects such as porosity, segregation and tears. The theory relates defect formation to the mechanical behaviour of the partially solidified microstructure when shear stresses are developed during the filling of a casting and by the subsequent feeding processes during solidification. Two transition points, the dendrite coherency point and the maximum packing solid fraction, divide the mushy zone into three regions of different mechanical and feeding behaviours. The response of the mush to shear is related to the presence of these zones during solidification of a casting. The resulting defects are rationalized by considering the governing local shear stress and shear rate, local strength and time available for fluid flow. The design of the casting, the casting process used and the alloy composition all influence the relative importance of shearing on defect formation. (C) 1998 Acta Metallurgica Inc. Published by Elsevier Science Ltd. All rights reserved.

Influence of Mg content on the microstructure and solid solution chemistry of Al-7%Si-Mg casting alloys during solution treatment

The solution treatment stage of the T6 heat-treatment of Al-7%Si-Mg foundry alloys influences microstructural features such as Mg2Si dissolution, and eutectic silicon spheroidisation and coarsening. Microstructural and microanalytical studies have been conducted across a range of Sr-modified Al-7%Si alloys, with an Fe content of 0.12% and Mg contents ranging from 0.3-0.7wt%. Qualitative and quantitative metallography have shown that, in addition to the above changes, solution treatment also results in changes to the relative proportions of iron-containing intermetallic particles and that these changes are composition-dependent. While solution treatment causes a substantial transformation of pi phase to beta phase in low Mg alloys (0.3-0.4%), this change is not readily apparent at higher Mg levels (0.6-0.7%). The pi to beta transformation is accompanied by a release of Mg into the aluminum matrix over and above that which arises from the rapid dissolution of Mg2Si. Since the level of matrix Mg retained after quenching controls an alloy's subsequent precipitation hardening response, a proper understanding of this phase transformation is crucial if tensile properties are to be maximised.

Semisolid casting of AlSi7Mg0.35 alloy produced by low-temperature pouring

AlSi7Mg0.35 alloy was cast into permanent moulds using different pouring temperatures (725 to 625degreesC). As the pouring temperature decreased, the as-cast microstructure changed from a coarse dendritic structure, through fine equiaxed grains to fine rosette-like grains. The as-cast materials were then partially remelted and isothermally held at 580degreesC prior to semisolid casting into a stepped die. The feedstock material cast from a high temperature filled only half the die, with severe segregation and other defects. The low-temperature-poured material completely filled the die with negligible porosity. The quality of semisolid castings is significantly affected by the microstructure of the semisolid feedstock material that arises from a combination of as-cast and subsequent thermal treatment conditions. The paper describes (a) the influence of pouring temperature on the microstructure of feedstock; (b) microstructure evolution through remelting and (c) the quality of semisolid castings produced with this material. For A17Si0.35Mg alloy, low temperature pouring in the range of 625-650degreesC followed by suitable isothermal holding treatment can result in good quality semisolid casting.

Improved VDC casting of aluminium alloys through an understanding of the surface properties of the molten metal

Vertical direct chill (VDC) casting of aluminium alloys is a mature process that has evolved over many decades through gradual change to both equipment design and casting practice. Today, air-pressurised, continuous lubrication, hot top mould systems with advanced station automation are selected as the process of choice for producing extrusion billet. Specific sets of operating parameters are employed on these stations for each alloy and size combination to produce optimal billet quality. The designs and parameters are largely derived from past experience and accumulated know-how. Recent experimental work at the University of Queensland has concentrated on understanding the way in which the surface properties of liquid aluminium alloys, e.g., surface tension, wetting angle and oxide skin strength, influence the size and shape of the naturally-stab le meniscus for a given alloy, temperature and atmosphere. The wide range of alloy-and condition-dependent values measured has led to the consideration of how these properties impact the stability of the enforced molten metal meniscus within the hot top mould cavity. The actual shape and position of the enforced meniscus is controlled by parameters such as the upstream conduction distance (UCD) from sub-mould cooling and the molten metal head. The degree of deviation of this actual meniscus from the predicted stable meniscus is considered to be a key driver in surface defect formation. This paper reports on liquid alloy property results and proposes how this knowledge might be used to better design VDC mould systems and casting practices.