Conduction of electricity through gases and radio-activity; a text-book with experiments,

Mode of access: Internet.

The determination of the helium discharge detector response to fixed gases

The Beckman Helium Discharge Detector has been found to be sensitive to the fixed gases oxygen, nitrogen, and hydrogen at detection levels 10-100 times more sensitive than possible with a Bow-Mac Thermal Conductivity Detector. Detection levels o~ approximately 1.9 E-4 ~ v/v oxygen, 3.1 E-4 ~ v/v nitrogen, and 3.0 E-3 ~ v/v hydrogen are estimated. Response of the Helium Discharge Detector was not linear, but is useable for quantitation over limited ranges of concentration using suitably prepared working standards. Cleanliness of the detector discharge electrodes and purity of the helium carrier and discharge gas were found to be critical to the operation of the detector. Higher sensitivities of the Helium Discharge Detector may be possible by the design and installation of a sensitive, solid-state electrometer.

Investigation of current-voltage and flow characteristics of an electric discharge across the exit of the AFFDL 1-Mw arc air heater

"Sponsored by the Air Force Flight Dynamics Laboratory ... under Contract AF 33(615)-1835."

Oscillatory phenomena in spark discharges

At head of title: Office of Naval Research. Contract N6 onr 243. Task order IV. Technical report no. 2.

An electric discharge as a trap for diffusion pump vacuum systems /

An electrical discharge is used as a trap for a diffusion pump using DC-704 silicone pump fluid. The discharge cracks the pump fluid vapor thus taking it out of the system. In the process much hydrogen and some other lighter gases are evolved.

The moving striations in argon glow discharges

Office of Naval Research. Contract N6 onr-243. Task order IV. Technical report no. 3.

Oscillatory phenomena in direct current glow discharges

Office of Naval Research. Contract ONR 243. Task order V. Technical report no. 1.

Electricity in gases,

Bibliographical foot-notes.

A study of plasma stability in microwave cavities by a frequency-shift analog.

"Prepared for the Air Force Ballistic Missile Division, Headquarters Air Research and Development Command, under contract AF 04 (647)-309, Thermonuclear Propulsion Research."

The use of low impedance transmission lines in plasma heating and confinement studies,

"Prepared for the Air Force Ballistic Missile Division, Headquarters Air Research and Development Command, under Contract AF 04(647)-309, Thermonuclear Propulsion Research."

Yield of metastable atoms from a rare gas discharge in a longitudinal magnetic field

Atomic beam experiments are limited by intensity. Intensity limitations are specially critical in the measurements of metastable atoms, since their relative population is several order of magnitude smaller than the beam population. This thesis provides a method for increasing the intensity of metastable argon and neon beams effusing from a hot cathode, glow discharge by use of a longitudinal magnetic field. The argon and neon metastable atom intensities have been measured for a range of discharge pressure, voltage, and current for a magnetic field strengths from 0 to 31 mT. For both argon and neon, the metastable atom beam intensity rises to a maximum value about one order of magnitude above the zero field case. A qualitative discussion of the theory of this phenomenon is also presented.

Vapour layer formation by electrical discharges through electrically conducting liquids-modelling and experiment

Experimental and finite element modelling methods are used to study the formation of vapour layers in electrical discharges through saline solutions. The experiments utilize shadowgraphic and photometric methods to observe the time dependence of thin vapour layers and plasma formation around electrodes driven by moderate voltage (<500 V) pulses, applied to an electrode immersed in a conducting saline solution. Finite element multiphysics software, coupling thermal and electrical effects, is employed to model the vapour layer formation. All relevant electrical and thermal properties of the saline are incorporated into the model, but hydrodynamic and surface tension effects are ignored. Experimental shadowgraph and modelling images are compared, as are current histories, and the agreement is very good. The comparison of experiment and modelling gives insight into both vapour layer production and subsequent plasma production. We show that, for example, superheating of the saline above its normal vaporization temperature may be playing a significant role in vapour formation. We also show that electric fields of approaching 10(7) V m(-1) can be achieved in the vapour layer.

Growth of aligned single-walled carbon nanotubes under ac electric fields through floating catalyst chemical vapour deposition

Through floating catalyst chemical vapour deposition(CVD) method, well-aligned isolated single-walled carbon nanotubes (SWCNTs) and their bundles were deposited on the metal electrodes patterned on the SiO2/Si surface under ac electric fields at relatively low temperature(280 degrees C). It was indicated that SWCNTs were effectively aligned under ac electric fields after they had just grown in the furnace. The time for a SWCNT to be aligned in the electric field and the effect of gas flow were estimated. Polarized Raman scattering was performed to characterize the aligned structure of SWCNTs. This method would be very useful for the controlled fabrication and preparation of SWCNTs in practical applications.

Intelligent management of end consumers loads including electric vehicles through a SCADA system

The large penetration of intermittent resources, such as solar and wind generation, involves the use of storage systems in order to improve power system operation. Electric Vehicles (EVs) with gridable capability (V2G) can operate as a means for storing energy. This paper proposes an algorithm to be included in a SCADA (Supervisory Control and Data Acquisition) system, which performs an intelligent management of three types of consumers: domestic, commercial and industrial, that includes the joint management of loads and the charge/discharge of EVs batteries. The proposed methodology has been implemented in a SCADA system developed by the authors of this paper – the SCADA House Intelligent Management (SHIM). Any event in the system, such as a Demand Response (DR) event, triggers the use of an optimization algorithm that performs the optimal energy resources scheduling (including loads and EVs), taking into account the priorities of each load defined by the installation users. A case study considering a specific consumer with several loads and EVs is presented in this paper.

On the variations of the photo-electric current due to heating and the occlusion and emission of gases ...

Thesis t.-p. attached to the cover of the issue reprinted from the Physical review, n.s., vol. xii, no. 4, October 1918.