Numerical and experimental studies of cold-formed steel floor systems under standard fire conditions

Light gauge cold-formed steel frame (LSF) structures are increasingly used in industrial, commercial and residential buildings because of their non-combustibility, dimensional stability, and ease of installation. A floor-ceiling system is an example of its applications. LSF floor-ceiling systems must be designed to serve as fire compartment boundaries and provide adequate fire resistance. Fire rated floor-ceiling assemblies formed with new materials and construction methodologies have been increasingly used in buildings. However, limited research has been undertaken in the past and hence a thorough understanding of their fire resistance behaviour is not available. Recently a new composite panel in which an external insulation layer is used between two plasterboards has been developed at QUT to provide a higher fire rating to LSF floors under standard fire conditions. But its increased fire rating could not be determined using the currently available design methods. Research on LSF floor systems under fire conditions is relatively recent and the behaviour of floor joists and other components in the systems is not fully understood. The present design methods thus require the use of expensive fire protection materials to protect them from excessive heat increase during a fire. This leads to uneconomical and conservative designs. Fire rating of these floor systems is provided simply by adding more plasterboard sheets to the steel joists and such an approach is totally inefficient. Hence a detailed fire research study was undertaken into the structural and thermal performance of LSF floor systems including those protected by the new composite panel system using full scale fire tests and extensive numerical studies. Experimental study included both the conventional and the new steel floor-ceiling systems under structural and fire loads using a gas furnace designed to deliver heat in accordance with the standard time- temperature curve in AS 1530.4 (SA, 2005). Fire tests included the behavioural and deflection characteristics of LSF floor joists until failure as well as related time-temperature measurements across the section and along the length of all the specimens. Full scale fire tests have shown that the structural and thermal performance of externally insulated LSF floor system was superior than traditional LSF floors with or without cavity insulation. Therefore this research recommends the use of the new composite panel system for cold-formed LSF floor-ceiling systems. The numerical analyses of LSF floor joists were undertaken using the finite element program ABAQUS based on the measured time-temperature profiles obtained from fire tests under both steady state and transient state conditions. Mechanical properties at elevated temperatures were considered based on the equations proposed by Dolamune Kankanamge and Mahendran (2011). Finite element models were calibrated using the full scale test results and used to further provide a detailed understanding of the structural fire behaviour of the LSF floor-ceiling systems. The models also confirmed the superior performance of the new composite panel system. The validated model was then used in a detailed parametric study. Fire tests and the numerical studies showed that plasterboards provided sufficient lateral restraint to LSF floor joists until their failure. Hence only the section moment capacity of LSF floor joists subjected to local buckling effects was considered in this research. To predict the section moment capacity at elevated temperatures, the effective section modulus of joists at ambient temperature is generally considered adequate. However, this research has shown that it leads to considerable over- estimation of the local buckling capacity of joist subject to non-uniform temperature distributions under fire conditions. Therefore new simplified fire design rules were proposed for LSF floor joist to determine the section moment capacity at elevated temperature based on AS/NZS 4600 (SA, 2005), NAS (AISI, 2007) and Eurocode 3 Part 1.3 (ECS, 2006). The accuracy of the proposed fire design rules was verified with finite element analysis results. A spread sheet based design tool was also developed based on these design rules to predict the failure load ratio versus time, moment capacity versus time and temperature for various LSF floor configurations. Idealised time-temperature profiles of LSF floor joists were developed based on fire test measurements. They were used in the detailed parametric study to fully understand the structural and fire behaviour of LSF floor panels. Simple design rules were also proposed to predict both critical average joist temperatures and failure times (fire rating) of LSF floor systems with various floor configurations and structural parameters under any given load ratio. Findings from this research have led to a comprehensive understanding of the structural and fire behaviour of LSF floor systems including those protected by the new composite panel, and simple design methods. These design rules were proposed within the guidelines of the Australian/New Zealand, American and European cold- formed steel structures standard codes of practice. These may also lead to further improvements to fire resistance through suitable modifications to the current composite panel system.

Dimensionamento de Madres Enformadas a Frio Travadas por Painéis do Tipo Sandwich

O presente relatório de estágio foi elaborado no âmbito da Unidade Curricular de DIPRE, Dissertação/Projeto/Estágio, do 2.º ano de Mestrado em Engenharia Civil do Instituto Superior de Engenharia do Porto, do ramo de estruturas, tendo como principal foco, a análise e dimensionamento de madres de aço enformado a frio e sua utilização com painéis do tipo sandwich em coberturas. Seções enformadas a frio são cada vez mais utilizadas em construções modernas, especificamente como estrutura secundária em coberturas, onde geralmente são fixas a painéis através de ligações aparafusadas. A presença de painéis e fixações através de parafusos permitem a estabilização lateral e torsional de madres aumentando desta forma a capacidade resistente, mas por serem elementos estruturais de espessura reduzida, os enformados a frio são suscetíveis a fenómenos de instabilidade associados. Desta forma, a norma EN 1993-1-3 [4] permite a análise e dimensionamento deste tipo de elementos através das disposições regulamentares preconizadas nas partes 1-1 [3] e 1-5 [5] da mesma norma. Num primeiro estudo, o presente trabalho tem como objetivo o dimensionamento e verificação de segurança de elementos enformados a frio com base na seção efetiva determinada com o auxílio das normas EN 1993-1-1 (regras gerais) e EN 1993-1-5 (regras para elementos estruturais constituídos por placas). Numa segunda fase, este trabalho pretende apresentar um estudo do comportamento de interação entre os sistemas madres-painéis. Para tal, são quantificadas as rigidezes das conexões dos sistemas e dos painéis para se realizarem a análise relativamente à restrição lateral e restrição torsional de madres. Neste contexto, concluiu-se que os painéis, quando fixos de forma adequada às madres, contribuem para a estabilidade.

Elementos de apoio ao dimensionamento de secções compostas em light steel framing

Dissertação de Mestrado, Engenharia Civil, Especialização em Estruturas, Instituto Superior de Engenharia, Universidade do Algarve, 2016

Section 936 as a development resource in the Caribbean : suggestions for a more effective policy /

Cover title.

Property improvement loan insurance; administrative regulations under title I, section 2 of the National Housing Act, as amended, effective October 1, 1954.

"Title 24, chapter 11, subchapter B, part 201, Code of federal regulations, 1949."

IRS examination data reveal an effective administration of Section 482 regulations : report to the Associate Commissioner (Operations) /

Mode of access: Internet.

The clinical effectiveness of interventions to assist perioperative temperature management for women undergoing Cesarean Section : a systematic review

Background Women undergoing Cesarean Section (CS) are vulnerable to the adverse effects associated with perioperative core temperature drop, in part due to the tendency for CS to be performed under neuraxial anesthesia, blood and fluid loss, and vasodilation. Inadvertent perioperative hypothermia (IPH) is a common condition that affects patients undergoing surgery of all specialties and is detrimental to all age groups, including neonates. Previous systematic reviews on IPH prevention largely focus on either adult or all ages populations, and have mainly overlooked pregnant or CS patients as a distinct group. Not all recommendations made by systematic reviews targeting all adult patients may be transferable to CS patients. Alternative, effective methods for preventing or managing hypothermia in this group would be valuable. Objectives To synthesize the best available evidence in relation to preventing and/or treating hypothermia in mothers after CS surgery. Types of participants Adult patients over the age of 18 years, of any ethnic background, with or without co-morbidities, undergoing any mode of anesthesia for any type of CS (emergency or planned) at healthcare facilities who have received interventions to limit or manage perioperative core heat loss were included. Types of intervention(s) Active or passive warming methods versus usual care or placebo, that aim to limit or manage core heat loss as applied to women undergoing CS were included. Types of studies Randomized controlled trials (RCTs) that met the inclusion criteria, with reduction of perioperative hypothermia a primary or secondary outcome were considered. Types of outcomes Primary outcome: maternal core temperature measured during the preoperative, intraoperative and postoperative phases of care Secondary outcomes: newborn core temperature at birth, umbilical pH obtained immediately after birth, Apgar scores, length of Post Anesthetic Care Unit (PACU) stay, maternal thermal comfort. Search strategy A comprehensive search was undertaken of the following databases from their inception until May 2012: ProQuest, Web of Science, Scopus, Dissertation and Theses PQDT (via ProQuest), Current Contents, CENTRAL, Mednar, OpenGrey, Clinical Trials. There were no language restrictions. Methodological quality Retrieved papers were assessed for methodological quality by two independent reviewers prior to inclusion using JBI software. Disagreements were resolved via consultation with the third reviewer. An assessment of quality of the included papers was also made in relation to five key quality factors. Data collection Two independent reviewers extracted data from the included papers using a previously piloted customized data extraction tool. Results 12 studies with a combined total of 719 participants were included. Three broad intervention groups were identified; intravenous (IV) fluid warming, warming devices, leg wrapping. IV fluid warming, whether administered intraoperatively or preoperatively, was found to be effective at maintaining maternal (but not neonatal) temperature and preventing shivering, but does not improve thermal comfort. The effectiveness of IV fluid warming on Apgar scores and umbilical pH remains unclear. Warming devices, including forced air warming and under body carbon polymer mattresses, were effective at preventing hypothermia and reduced shivering, however were most effective if applied preoperatively. The effectiveness of warming devices to improve thermal comfort remains unclear. Preoperative forced air warming appears to aid maintenance of neonatal temperature, while intraoperative forced air warming does not. Forced air warming was not effective at improving Apgar scores and the effects for umbilical pH remain unclear. Conclusions Intravenous fluid warming, by any method, improves maternal temperature and reduces shivering for women undergoing CS. Preoperative body warming devices also improve maternal temperature, in addition to reducing shivering.

Building distributed leadership for effective supervision of creative practice higher research degrees : final report 2014

Building distributed leadership for effective supervision of creative practice higher research degrees is an Office for Learning and Teaching (OLT) funded project, conducted in partnership between Queensland University of Technology, The University of Melbourne, Auckland University of Technology, University of New South Wales and University of Western Sydney. The project was initiated to develop a cooperative approach to establishing an understanding of the contextual frameworks of the emergent field of creative practice higher degrees by research (HDRs); capturing early insights of administrators and supervisors; gathering exemplars of good practices; and establishing an in-common understanding of effective approaches to supervision. To this end, the project has produced: • A literature review, to provide a research foundation for creative practice higher research degree supervision (Chapter 3). • A contextual review of disciplinary frameworks for HDR programs, produced through surveys of postgraduate research administrators (Section 4.1), and an analysis of institutional materials and academic development programs for supervisors (Section 4.2). • A National Symposium, Effective Supervision of Creative Arts Research Degrees (ESCARD), at QUT in Brisbane in February 2013, with 62 delegates from 20 Australasian Universities, at which project findings were disseminated, and delegates presented case studies and position papers, and participated in discussions on key issues for supervisors (Appendix 1). • Resources, including a booklet for supervisors: 12 Principles for the Effective Supervision of Creative Practice Higher Research Degrees, which encapsulates attitudes, insights and good practices of experienced and new supervisors. It was produced through a content analysis of interviews with twenty-five supervisors in creative disciplines (visual and performing arts, music, new media, creative writing and design) (Printed booklet, PDF, Appendix 3). • A project website to disseminate project outcomes , which holds project findings, relevant references, and a repository of case studies and position papers by supervisors and program administrators. • A call for papers for a special issue ‘Supervising Practice: Perspectives on the Supervision of Creative Practice Research Higher Degrees’ of ACCESS Journal: Critical Perspectives on Communication, Cultural & Policy Studies (ERA ranked A quality) in 2014 (Appendix 2). • A community of supervisory practice initiated through project partnerships, a national symposium where supervisors from across Australasia met in dialogue for the first time, resource sharing, and joint publishing opportunities. • A set of recommendations for supervision capacity building and academic development, produced through the triangulation of literature and contextual reviews, analysis of institutional frameworks, interviews with supervisors and national dialogues. It is anticipated that the project’s outcomes will support experienced and new supervisors in this emergent field, and so benefit HDR students, and will enable creative disciplines to build supervision capacity, and so to accommodate growth in postgraduate enrolments. Funded as a pilot project, the project set out to establish a robust research base to provide a foundation for future work involving sharing good practices, resource building, and designing effective approaches to academic development for supervisors. Recommendations that were produced out of this project include the need to extend beyond generic, formal training for supervisors to academic development that harnesses and extends distributed leadership; focuses on local, disciplinary contexts; has a strong emphasis on case studies; provides diverse resources; and facilitates dialogue between supervisors. Recommendations also include developing frameworks for mentoring new supervisors and building a national network to facilitate cross-institutional discourse, disseminate good practices, and share insights into the management of risk factors, ethical issues, and preparing candidates for examination. As a pilot investigation, the outcomes of this project lay the ground for this future work.

Preventing infections following caesarean section

Surgical site infections following caesarean section are a serious and costly adverse event for Australian hospitals. In the United Kingdom, 9% of women are diagnosed with a surgical site infection following caesarean section either in hospital or post-discharge (Wloch et al 2012, Ward et al 2008). Additional staff time, pharmaceuticals and health supplies, and increased length of stay or readmission to hospital are often required (Henman et al 2012). Part of my PhD investigated the economics of preventing post-caesarean infection. This paper summarises a review of relevant infection prevention strategies. Administering antibiotic prophylaxis 15 to 60 minutes pre-incision, rather than post cordclamping, is probably the most important infection prevention strategy for caesarean section (Smaill and Gyte2010, Liu et al 2013, Dahlke et al 2013). However the timing of antibiotic administration is reportedly inconsistent in Australian hospitals. Clinicians may be taking advice from the influential, but out-dated RANZCOG and United States Centers for Disease Control and Prevention guidelines (Royal Australian and New Zealand College of Obstetricians and Gynaecologists 2011, Mangram et al 1999). A number of other important international clinical guidelines, including Australia's NHMRC guidelines, recommend universal prophylactic antibiotics pre-incision for caesarean section (National Health and Medical Research Council 2010, National Collaborating Centre for Women's and Children's Health 2008, Anderson et al 2008, National Collaborating Centre for Women's and Children's Health 2011, Bratzler et al 2013, American College of Obstetricians and Gynecologists 2011a, Antibiotic Expert Group 2010). We need to ensure women receive preincision antibiotic prophylaxis, particularly as nurses and midwives play a significant role in managing an infection that may result from sub-optimal practice. It is acknowledged more explicitly now that nurses and midwives can influence prescribing and administration of antibiotics through informal approaches (Edwards et al 2011). Methods such as surgical safety checklists are a more formal way for nurses and midwives to ensure that antibiotics are administered pre-incision (American College of Obstetricians and Gynecologists 2011 b). Nurses and midwives can also be directly responsible for other infection prevention strategies such as instructing women to not remove pubic hair in the month before the expected date of delivery and wound management education (Ng et al 2013). Potentially more costly but effective strategies include using a Chlorhexidine-gluconate (CHG) sponge preoperatively (in addition to the usual operating room skin preparation) and vaginal cleansing with a povidone-iodine solution (Riley et al 2012, Rauk 2010, Haas, Morgan, and Contreras 2013).

Total cross-section at LHC from minijets and soft gluon resummation in the infrared region

A model for total cross-sections incorporating QCD jet cross-sections and soft gluon resummation is described and compared with present data on pp and pp cross-sections. Predictions for LHC are presented for different parameter sets. It is shown that they differ according to the small x-behaviour of available parton density functions.

The fluorescence of Nd3+ in lead borate and bismuth borate glasses with large stimulated emission cross section

The stimulated emission cross section σp for the 1060 nm transition of Nd3+ in lead borate and bismuth borate glasses has been determined from fluorescence measurements. The compositional dependence of σp, which has been evaluated using radiative transition probability, refractive index of the host glass, effective fluorescence linewidth, and position of the band, with PbO/Bi2O3 content is investigated. The σp values of the 1060 nm band of Nd3+ for lead borate and bismuth borate glasses are found to be in the range 2.6–5.7×10−20 cm2 at 298 K and 3.0–6.3×10−20 cm2 at 4.2 K. The σp values are comparatively large suggesting the possible utilization of these materials in laser applications.

A generalized self-consistent method accounting for fiber section shape

A three-phase confocal elliptical cylinder model is proposed for fiber-reinforced composites, in terms of which a generalized self-consistent method is developed for fiber-reinforced composites accounting for variations in fiber section shapes and randomness in fiber section orientation. The reasonableness of the fiber distribution function in the present model is shown. The dilute, self-consistent, differential and Mori-Tanaka methods are also extended to consider randomness in fiber section orientation in a statistical sense. A full comparison is made between various micromechanics methods and with the Hashin and Shtrikman's bounds. The present method provides convergent and reasonable results for a full range of variations in fiber section shapes (from circular fibers to ribbons), for a complete spectrum of the fiber volume fraction (from 0 to 1, and the latter limit shows the correct asymptotic behavior in the fully packed case) and for extreme types of the inclusion phases (from voids to rigid inclusions). A very different dependence of the five effective moduli on fiber section shapes is theoretically predicted, and it provides a reasonable explanation on the poor correlation between previous theory and experiment in the case of longitudinal shear modulus.

Genetic improvement and effective dissemination: keys to prosperous and sustainable aquaculture industries

There is an increasing demand for fish in the world due to a growing population, better economic situation in some sectors, and greater awareness of health issues in relation to food. Since capture fisheries have stagnated, fish farming has become a very fast growing food production system. In this presentation, the author gives an overview of the technologies that are available for genetic improvement of fish, and briefly discuss their merit in the context of a sustainable development. He also discusses the essential prerequisites for effective dissemination of improved stock to farmers. It is concluded that genetic improvement programs based on selective breeding can substantially contribute to sustainable fish production systems. Furthermore, if such genetic improvement programs are followed up with effective dissemination strategies, they can result in a positive impact on farmers' incomes.

Temperature dependence of the 1.03 mu m stimulated emission cross section of Cr : Yb : YAG crystal

The fluorescence emission spectra of Cr:Yb:YAG crystal are measured and the effective stimulated emission cross section of the crystal are obtained from -80 degrees C to +80 degrees C. A linear temperature dependence between -80 degrees C and +80 degrees C is reported for the 1.03 mu m peak stimulated emission cross section of Cr:Yb:YAG crystal. (c) 2004 Elsevier B.V. All rights reserved.

Temperature dependence of the 1.064-mu m stimulated emission cross-section of Cr : Nd : YAG crystal

The fluorescence emission spectra of Cr:Nd:YAG crystal are measured and the effective stimulated emission cross-section of the crystal is obtained from -80 to +80 degrees C. A linear temperature dependence between -80 and +80 degrees C is reported for the 1.064-mu m peak stimulated emission cross-section of Cr:Nd:YAG crystal. (C) 2005 Elsevier Ltd. All rights reserved.