Desconnexió de la xarxa

Treball de recerca realitzat per un alumne d'ensenyament secundari i guardonat amb un Premi CIRIT per fomentar l'esperit cientí­fic del Jovent l'any 2009. Aquest treball es planteja com un repte la necessitat de connexió a una xarxa de subministrament elèctric i d'aigua. L'objectiu del treball ha estat comprovar si, tan tècnicament com econòmica, es pot aconseguir l'autosuficiència d'una casa de muntanya del Vallès Oriental tot aprofitant els recursos que ens ofereix el medi, però sense haver de renunciar al nivell de vida al qual ens hem acostumat durant els darrers anys. Després d'una recollida de dades i valoració del consum energètic mínim que volem imposar, hem dissenyat una instal·lació capaç d'aprofitar les energies renovables de l'entorn i de satisfer les nostres necessitats. La instal·lació inclou plaques fotovoltaiques, col·lectors solars, cisternes per a la recollida d'aigua, bombes, etc. Finalment, s'inclou un pressupost d'aquesta instal·lació, que indica que els diners que caldria invertir són massa. Es demostra, doncs, que l'autosuficiència d'aquesta casa és tècnicament viable, però econòmicament inviable (o gens rendible).

Production of Acetic Acid by Fermentation with Propionibacteria, HR-321, 1993

This project was undertaken jointly with a project supported by the Iowa Corn Promotion Board. Together the projects aimed at producing the organic acids, propionic acid and acetic acid, by fermentation. The impacts were to provide agriculturally-based alternatives to production of these acids, currently produced mainly as petrochemicals. The potentially high-demand use for acetic acid is as the "acetate" in Calcium Magnesium Acetate (CMA), the non-corrosive road deicer. Fermentation was, however, far from being an economically acceptable alternative. Gains were made in this work toward making this a feasible route. These advances included (1) development of a variant strain of propionibacteria capable of producing higher concentrations of acids; (2) comparison of conditions for several ways of cultivating free cells and establishment of the relative benefits of each; (3) achievement of the highest productivity in fermentations using immobilized cells; (4) identification of corn steep liquor as a lower cost substrate for the fermentation; (5) application of a membrane extraction system for acid recovery and reduction of product inhibition; and (6) initial use of more detailed economic analysis of process alternatives to guide in the identification of where the greatest payback potential is for future research. At this point, the fermentation route to these acids using the propionibacteria is technically feasible, but economically unfeasible. Future work with integration of the above process improvements can be expected to lead to further gains in economics. However, such work can not be expected to make CMA a less expensive deicer than common road salt.

Aspectos econômicos da adubação fosfatada para cultura do milho

Estudos econômicos da adubação fosfatada fazem-se necessários, em razão da sua participação expressiva no custo de produção da cultura do milho, especialmente em solos sob vegetação de cerrado e face à competitividade da atividade no mercado globalizado. Assim, objetivou-se avaliar alguns aspectos econômicos de modos de aplicação da adubação fosfatada a lanço e sulco simples comparados ao modo alternativo em sulco duplo, utilizando o híbrido de milho BR 3123. Os tratamentos foram constituídos pelos modos de aplicação em sulco duplo, sulco simples e a lanço nas doses: 0; 0,50; 0,75; 1,00; 1,25; 1,50 vez a dose recomendada para adubação de manutenção para o milho, ou seja, 90 kg de P2O5 ha-1. Para a análise, considerou-se o preço médio da década de 90 para a tonelada do milho e do superfosfato triplo em R$189,33 e R$494,32, respectivamente, e o custo operacional total de R$ 752,90 ha-1. O aumento das doses de adubo fosfatado, em geral, incrementou a produção, o valor da produção e a receita líquida por hectare; a aplicação do adubo fosfatado a lanço não se mostrou viável economicamente; o modo alternativo em sulco duplo permitiu maior receita líquida e uma relação benefício/custo 17,7% superior, em relação ao sulco simples.

Relações entre condutividade hidráulica, transmissividade, condutância longitudinal e sólidos totais dissolvidos para o aquífero livre de Caçapava do Sul (RS), Brasil

A água subterrânea é um importante recurso ao abastecimento público, principalmente para comunidades periféricas em grandes cidades ou pequenos municípios, onde a instalação ou prolongamento de sistemas de distribuição são economicamente inviáveis. Estudos voltados à análise da vulnerabilidade de aquíferos são relevantes para subsídio a políticas públicas em saneamento básico e preservação ambiental. Este estudo contou com o cadastro de 23 poços rasos localizados no município de Caçapava do Sul (RS), onde foram realizadas medidas de resistividade elétrica e cargabilidade por meio de geofísica, e medidas diretas de condutividade hidráulica e sólidos totais dissolvidos. A análise estatística dos dados demonstrou diversos graus de correlação entre parâmetros, basicamente condicionados a fatores geológicos como porosidade, permeabilidade e sólidos totais dissolvidos.

Análise de viabilidade econômica de um aterro sanitário para cidade de pequeno porte

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Análise da sustentabilidade econômica e social na produção extensiva de ostras em uma região subtropical

Pós-graduação em Aquicultura - FCAV

LiDAR remote sensing applied to forest resources assessment

Disponer de información precisa y actualizada de inventario forestal es una pieza clave para mejorar la gestión forestal sostenible y para proponer y evaluar políticas de conservación de bosques que permitan la reducción de emisiones de carbono debidas a la deforestación y degradación forestal (REDD). En este sentido, la tecnología LiDAR ha demostrado ser una herramienta perfecta para caracterizar y estimar de forma continua y en áreas extensas la estructura del bosque y las principales variables de inventario forestal. Variables como la biomasa, el número de pies, el volumen de madera, la altura dominante, el diámetro o la altura media son estimadas con una calidad comparable a los inventarios tradicionales de campo. La presente tesis se centra en analizar la aplicación de los denominados métodos de masa de inventario forestal con datos LIDAR bajo diferentes condiciones y características de masa forestal (bosque templados puros y mixtos) y utilizando diferentes bases de datos LiDAR (información proveniente de vuelo nacionales e información capturada de forma específica). Como consecuencia de lo anterior, se profundiza en la generación de inventarios forestales continuos con LiDAR en grandes áreas. Los métodos de masa se basan en la búsqueda de relaciones estadísticas entre variables predictoras derivadas de la nube de puntos LiDAR y las variables de inventario forestal medidas en campo con el objeto de generar una cartografía continua de inventario forestal. El rápido desarrollo de esta tecnología en los últimos años ha llevado a muchos países a implantar programas nacionales de captura de información LiDAR aerotransportada. Estos vuelos nacionales no están pensados ni diseñados para fines forestales por lo que es necesaria la evaluación de la validez de esta información LiDAR para la descripción de la estructura del bosque y la medición de variables forestales. Esta información podría suponer una drástica reducción de costes en la generación de información continua de alta resolución de inventario forestal. En el capítulo 2 se evalúa la estimación de variables forestales a partir de la información LiDAR capturada en el marco del Plan Nacional de Ortofotografía Aérea (PNOA-LiDAR) en España. Para ello se compara un vuelo específico diseñado para inventario forestal con la información de la misma zona capturada dentro del PNOA-LiDAR. El caso de estudio muestra cómo el ángulo de escaneo, la pendiente y orientación del terreno afectan de forma estadísticamente significativa, aunque con pequeñas diferencias, a la estimación de biomasa y variables de estructura forestal derivadas del LiDAR. La cobertura de copas resultó más afectada por estos factores que los percentiles de alturas. Considerando toda la zona de estudio, la estimación de la biomasa con ambas bases de datos no presentó diferencias estadísticamente significativas. Las simulaciones realizadas muestran que las diferencias medias en la estimación de biomasa entre un vuelo específico y el vuelo nacional podrán superar el 4% en áreas abruptas, con ángulos de escaneo altos y cuando la pendiente de la ladera no esté orientada hacia la línea de escaneo. En el capítulo 3 se desarrolla un estudio en masas mixtas y puras de pino silvestre y haya, con un enfoque multi-fuente empleando toda la información disponible (vuelos LiDAR nacionales de baja densidad de puntos, imágenes satelitales Landsat y parcelas permanentes del inventario forestal nacional español). Se concluye que este enfoque multi-fuente es adecuado para realizar inventarios forestales continuos de alta resolución en grandes superficies. Los errores obtenidos en la fase de ajuste y de validación de los modelos de área basimétrica y volumen son similares a los registrados por otros autores (usando un vuelo específico y parcelas de campo específicas). Se observan errores mayores en la variable número de pies que los encontrados en la literatura, que pueden ser explicados por la influencia de la metodología de parcelas de radio variable en esta variable. En los capítulos 4 y 5 se evalúan los métodos de masa para estimar biomasa y densidad de carbono en bosques tropicales. Para ello se trabaja con datos del Parque Nacional Volcán Poás (Costa Rica) en dos situaciones diferentes: i) se dispone de una cobertura completa LiDAR del área de estudio (capitulo 4) y ii) la cobertura LiDAR completa no es técnica o económicamente posible y se combina una cobertura incompleta de LiDAR con imágenes Landsat e información auxiliar para la estimación de biomasa y carbono (capitulo 5). En el capítulo 4 se valida un modelo LiDAR general de estimación de biomasa aérea en bosques tropicales y se compara con los resultados obtenidos con un modelo ajustado de forma específica para el área de estudio. Ambos modelos están basados en la variable altura media de copas (TCH por sus siglas en inglés) derivada del modelo digital LiDAR de altura de la vegetación. Los resultados en el área de estudio muestran que el modelo general es una alternativa fiable al ajuste de modelos específicos y que la biomasa aérea puede ser estimada en una nueva zona midiendo en campo únicamente la variable área basimétrica (BA). Para mejorar la aplicación de esta metodología es necesario definir en futuros trabajos procedimientos adecuados de medición de la variable área basimétrica en campo (localización, tamaño y forma de las parcelas de campo). La relación entre la altura media de copas del LiDAR y el área basimétrica (Coeficiente de Stock) obtenida en el área de estudio varía localmente. Por tanto es necesario contar con más información de campo para caracterizar la variabilidad del Coeficiente de Stock entre zonas de vida y si estrategias como la estratificación pueden reducir los errores en la estimación de biomasa y carbono en bosques tropicales. En el capítulo 5 se concluye que la combinación de una muestra sistemática de información LiDAR con una cobertura completa de imagen satelital de moderada resolución (e información auxiliar) es una alternativa efectiva para la realización de inventarios continuos en bosques tropicales. Esta metodología permite estimar altura de la vegetación, biomasa y carbono en grandes zonas donde la captura de una cobertura completa de LiDAR y la realización de un gran volumen de trabajo de campo es económica o/y técnicamente inviable. Las alternativas examinadas para la predicción de biomasa a partir de imágenes Landsat muestran una ligera disminución del coeficiente de determinación y un pequeño aumento del RMSE cuando la cobertura de LiDAR es reducida de forma considerable. Los resultados indican que la altura de la vegetación, la biomasa y la densidad de carbono pueden ser estimadas en bosques tropicales de forma adecuada usando coberturas de LIDAR bajas (entre el 5% y el 20% del área de estudio). ABSTRACT The availability of accurate and updated forest data is essential for improving sustainable forest management, promoting forest conservation policies and reducing carbon emissions from deforestation and forest degradation (REDD). In this sense, LiDAR technology proves to be a clear-cut tool for characterizing forest structure in large areas and assessing main forest-stand variables. Forest variables such as biomass, stem volume, basal area, mean diameter, mean height, dominant height, and stem number can be thus predicted with better or comparable quality than with costly traditional field inventories. In this thesis, it is analysed the potential of LiDAR technology for the estimation of plot-level forest variables under a range of conditions (conifer & broadleaf temperate forests and tropical forests) and different LiDAR capture characteristics (nationwide LiDAR information vs. specific forest LiDAR data). This study evaluates the application of LiDAR-based plot-level methods in large areas. These methods are based on statistical relationships between predictor variables (derived from airborne data) and field-measured variables to generate wall to wall forest inventories. The fast development of this technology in recent years has led to an increasing availability of national LiDAR datasets, usually developed for multiple purposes throughout an expanding number of countries and regions. The evaluation of the validity of nationwide LiDAR databases (not designed specifically for forest purposes) is needed and presents a great opportunity for substantially reducing the costs of forest inventories. In chapter 2, the suitability of Spanish nationwide LiDAR flight (PNOA) to estimate forest variables is analyzed and compared to a specifically forest designed LiDAR flight. This study case shows that scan angle, terrain slope and aspect significantly affect the assessment of most of the LiDAR-derived forest variables and biomass estimation. Especially, the estimation of canopy cover is more affected than height percentiles. Considering the entire study area, biomass estimations from both databases do not show significant differences. Simulations show that differences in biomass could be larger (more than 4%) only in particular situations, such as steep areas when the slopes are non-oriented towards the scan lines and the scan angles are larger than 15º. In chapter 3, a multi-source approach is developed, integrating available databases such as nationwide LiDAR flights, Landsat imagery and permanent field plots from SNFI, with good resultos in the generation of wall to wall forest inventories. Volume and basal area errors are similar to those obtained by other authors (using specific LiDAR flights and field plots) for the same species. Errors in the estimation of stem number are larger than literature values as a consequence of the great influence that variable-radius plots, as used in SNFI, have on this variable. In chapters 4 and 5 wall to wall plot-level methodologies to estimate aboveground biomass and carbon density in tropical forest are evaluated. The study area is located in the Poas Volcano National Park (Costa Rica) and two different situations are analyzed: i) available complete LiDAR coverage (chapter 4) and ii) a complete LiDAR coverage is not available and wall to wall estimation is carried out combining LiDAR, Landsat and ancillary data (chapter 5). In chapter 4, a general aboveground biomass plot-level LiDAR model for tropical forest (Asner & Mascaro, 2014) is validated and a specific model for the study area is fitted. Both LiDAR plot-level models are based on the top-of-canopy height (TCH) variable that is derived from the LiDAR digital canopy model. Results show that the pantropical plot-level LiDAR methodology is a reliable alternative to the development of specific models for tropical forests and thus, aboveground biomass in a new study area could be estimated by only measuring basal area (BA). Applying this methodology, the definition of precise BA field measurement procedures (e.g. location, size and shape of the field plots) is decisive to achieve reliable results in future studies. The relation between BA and TCH (Stocking Coefficient) obtained in our study area in Costa Rica varied locally. Therefore, more field work is needed for assessing Stocking Coefficient variations between different life zones and the influence of the stratification of the study areas in tropical forests on the reduction of uncertainty. In chapter 5, the combination of systematic LiDAR information sampling and full coverage Landsat imagery (and ancillary data) prove to be an effective alternative for forest inventories in tropical areas. This methodology allows estimating wall to wall vegetation height, biomass and carbon density in large areas where full LiDAR coverage and traditional field work are technically and/or economically unfeasible. Carbon density prediction using Landsat imaginery shows a slight decrease in the determination coefficient and an increase in RMSE when harshly decreasing LiDAR coverage area. Results indicate that feasible estimates of vegetation height, biomass and carbon density can be accomplished using low LiDAR coverage areas (between 5% and 20% of the total area) in tropical locations.

Estudo comparativo de utilização de SER, MIG/MAG e Friction Surfacing na reparação de braços de suspensão de VBTP-M113

Nas últimas décadas Friction Surfacing despertou bastante interesse por permitir revestir metais no estado sólido desenvolvendo-se a temperaturas inferiores às de fusão, evitando assim as afetações que dai advém. No presente trabalho existem dois blocos principais, um primeiro onde se caraterizou o material do braço de suspensão do M113, e um segundo onde se produziram revestimentos recorrendo às três técnicas de revestimento em estudo (FS, Fios Fluxados e SER), com o objetivo de se proceder ao seu estudo e comparação. No processo de caraterização do aço do braço, foram realizados diversos ensaios, dos quais se salientam os ensaios de durezas Vickers e os ensaios de faiscamento, concluindo-se que o aço que mais se assemelha com o do braço é o AISI 4140. Para a caraterização dos revestimentos foram definidos diferentes tipos de ensaios, Metalúrgicos e Mecânicos, com a finalidade principal de abranger uma ampla gama de solicitações semelhantes às que são requeridas ao componente em serviço. Nos ensaios Metalúrgicos foram avaliadas as ligações, a existência de defeitos, as ZTA e as alterações metalográficas. A avaliação das propriedades mecânicas foi obtida através de ensaios de dureza, desgaste, flexão em três pontos e Push-Pull. Da realização destes ensaios verificou-se que os revestimentos obtidos por FS apresentam melhores propriedades, tanto Metalúrgicas como Mecânicas Por fim, foi elaborada uma avaliação dos custos operacionais envolvidos na realização da reparação de um braço de suspensão, concluindo-se que FS, apesar de apresentar os revestimentos com melhores propriedades, é ainda uma tecnologia pouco viável economicamente, fato que se deve á baixa eficiência apresentada.

Thermotolerant fermenting yeasts for simultaneous saccharification fermentation of lignocellulosic biomass

Lignocellulosic biomass is the most abundant renewable source of energy that has been widely explored as second-generation biofuel feedstock. Despite more than four decades of research, the process of ethanol production from lignocellulosic (LC) biomass remains economically unfeasible. This is due to the high cost of enzymes, end-product inhibition of enzymes, and the need for cost-intensive inputs associated with a separate hydrolysis and fermentation (SHF) process. Thermotolerant yeast strains that can undergo fermentation at temperatures above 40°C are suitable alternatives for developing the simultaneous saccharification and fermentation (SSF) process to overcome the limitations of SHF. This review describes the various approaches to screen and develop thermotolerant yeasts via genetic and metabolic engineering. The advantages and limitations of SSF at high temperatures are also discussed. A critical insight into the effect of high temperatures on yeast morphology and physiology is also included. This can improve our understanding of the development of thermotolerant yeast amenable to the SSF process to make LC ethanol production commercially viable.

A new set of microsatellite markers for the genetic characterization of Ceratocystis fimbriata, an economically important plant pathogen

Ceratocystis fimbriata is a fungal pathogen which attacks several economically important plants, but occurs in host-associated, morphologically indistinguishable forms. In Brazil, this fungus seriously attacks mango trees (Mangifera indica), causing severe loss of yield. This work aimed to develop and characterize a novel set of microsatellite markers for this important pathogen, providing researchers with new molecular tools for the characterization of isolates. Twenty polymorphic primer pairs were designed from a microsatellite-enriched library. We tested the usefulness of these markers through genotyping thirteen isolates of the fungus. On average, 6.65 alleles per locus were detected, revealing the ability of this set of markers to characterize C. fimbriata isolates associated to mango and to other plant species.

Are virtual planning and guided surgery for head and neck reconstruction economically viable?

PURPOSE: Virtual planning and guided surgery with or without prebent or milled plates are becoming more and more common for mandibular reconstruction with fibular free flaps (FFFs). Although this excellent surgical option is being used more widely, the question of the additional cost of planning and cutting-guide production has to be discussed. In capped payment systems such additional costs have to be offset by other savings if there are no special provisions for extra funding. Our study was designed to determine whether using virtual planning and guided surgery resulted in time saved during surgery and whether this time gain resulted in self-funding of such planning through the time saved. MATERIALS AND METHODS: All consecutive cases of FFF surgery were evaluated during a 2-year period. Institutional data were used to determine the price of 1 minute of operative time. The time for fibula molding, plate adaptation, and insetting was recorded. RESULTS: During the defined period, we performed 20 mandibular reconstructions using FFFs, 9 with virtual planning and guided surgery and 11 freehand cases. One minute of operative time was calculated to cost US $47.50. Multiplying this number by the time saved, we found that the additional cost of virtual planning was reduced from US $5,098 to US $1,231.50 with a prebent plate and from US $6,980 to US $3,113.50 for a milled plate. CONCLUSIONS: Even in capped health care systems, virtual planning and guided surgery including prebent or milled plates are financially viable.

Respecting the deal: Economically sustainable management of open innovation among co-opeting companies

Platforms like eBay allow product seekers and providers to meet and exchange goods. On eBay, consumers can return a product if it does not correspond to expectations; eBay is the third-party firm in charge of assuring that the agreement among seekers and providers will be respected. Who provides the same service for what concerns open innovation, where specifications might not fully defined? This paper describes the business model of an organizational structure to support the elicitation and respect of agreements among agents, who have conflicting interests but that gain from cooperating together. Extending previous studies, our business model takes into account the economic dimensions concerning the needs of knowledge share and mutual control to allow a third-party to sustainably reinforce trust among untrusted partners and to lower their overall relational risk.

Comparisons between two economically valuable forest species (Eucalyptus grandis and Pinus taeda) in relation to seed behaviour under controlled deterioration

The objectives of this work were to analyze seed behaviour under controlled deterioration and estimate viability equations for forest species Eucalyptus grandis and Pinus taeda. Desired moisture content levels were achieved from initial values after either rehydration over water or drying over silica gel, both at 25 ºC. Seed sub samples with 8 moisture contents each for E. grandis (1.2 to 18.1%, initial value of 11.3%) and P. taeda (1.5 to 19.5%, initial value of 12.9%) were sealed in laminate aluminium-foil packets and stored in incubators maintained at 40, 50 and 65 ºC. The seeds from these species exhibited true orthodox and sub-orthodox storage behaviour, respectively, however E. grandis showed higher seed storability, probably due to a different seed chemical composition. Lowest moisture content limits estimated for application of the viability equations at 65 ºC were 4.9 and 4.1 mc for E. grandis and P. taeda, on equilibrium with ±20% RH. The viability equation estimated quantified the response of seed longevity to storage environment well with K E = 9.661 and 8.838; C W = 6.467 and 5.981; C H = 0.03498 and 0.10340; C Q = 0.0002330 and 0.0005476, for E. grandis and P. taeda, respectively.