Caracterização morfológica e microestrutural da perovskita BaCexPr1-xO3 sintetizada a partir do método de complexação combinando EDTA/Citrato

In this study, binary perovskite (BaCexO3) were doped with praseodymium (Pr) to obtainment of the ternary material BaCexPr1-xO3. This material was synthesized by the complexation method combining EDTA/Citrate with the stoichiometric ratio of the element Praseodymium ranging from x = 0.1 to x = 0.9 in order to determine the influence of this rare earth element on the morphology and microstructure of the final powder. At first the material was synthesized based on the route proposed by literature (Santos, 2010), and then characterized by SEM and XRD, besides being refined by the Rietveld method. In the material that had lowest residual parameter, S, and lowest average size of crystal, pH variation of synthesis solution was made in order to identify the influence of this parameter on the morphology and microscopy of the final powder. The results show that addition of praseodymium did not directly influence the crystallographic and lattice parameters, keeping even the same orthorhombic structure of the binary material BaCexO3, according to Yamanaka et al (2003). Material type BaCe0,2Pr0,8O3 had lowest residual parameter (S=1.4) and lowest average size of crystallite (26.4 nm), being used as reference in the pH variation of synthesis solution for 9, 7, 5 and 3, respectively. Variation of this parameter showed that when the synthesis solution pH was decreased to below 11, there was an increase in the average size of crystals, for pH 9, about 58.3%, for pH 7 (30.3 %), for pH 2 (2.3%) and for pH 3 (42%), indicating that the value initially used and quoted by Santos (2010) was the most coherent

Obtenção de ferrita de cobalto através de dois métodos de síntese: método de complexação combinando EDTA/Citrato e método hidrotérmico

In this work it was synthesized and characterized the cobalt ferrite (CoFe2O4) by two methods: complexation combining EDTA/Citrate and hydrothermal investigating the influence of the synthesis conditions on phase formation and on the crystallite size. The powders were mainly characterized by x-ray diffraction. In specific cases, it was also used scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), x-ray fluorescence (XRF) and isotherms of adsorption and desorption of nitrogen (BET method). The study of the crystallite size was based on the interpretation of x-ray diffractograms obtained and estimated by the method of Halder-Wagner-Scherrer and Langford. An experimental design was made in order to assist in quantifying the influence of synthesis conditions on the response variables. The synthesis parameters evaluated in this study were: pH of the reaction medium (8, 9 and 10), the calcination temperature (combined complexation method EDTA/Citrate 600°C, 800°C and 1000°C), synthesis temperature (hydrothermal method 120°C, 140°C and 160°C), calcination time (combined complexation method EDTA/Citrate - 2, 4 and 6 hours) and time of synthesis (hydrothermal method 6, 15 and 24 hours). By the hydrothermal method was possible to produce mesoporous powders with high purity, with an average crystallite size up to 7 nm, with a surface area of 113.44 m²/g in the form of pellets with irregular morphology. By using the method of combined complexation EDTA/Citrate, mesoporous powders were produced with greater purity, crystallite size up to 22nm and 27.95 m²/g of surface area in the form of pellets with a regular morphology of plaques. In the experimental design was found that the hydrothermal method to all the studied parameters (pH, temperature and time) have significant effect on the crystallite size, while to the combined complexation method EDTA/Citrate, only temperature and time were significant

Easy fabrication of dense ceramic membrane for oxygen separation

A combined EDTA-citrate complexing method was developed for the easy preparation of mixed oxygen-ionic and electronic conducting dense ceramic membrane for oxygen separation. The nea method takes the advantage of lower calcination temperature for phase formation. lower membrane sintering temperature and higher relative density over the standard ceramic method.

Partial oxidation of methane over the perovskite oxides

Ba0.5Sr0.5Co0.8Fe0.2O3-delta and Ba0.5Sr0.5Co0.8Ti0.2O3-delta oxides were synthesized by a combined EDTA-citrate complexing method. The catalytic behavior of these two oxides with the perovskite structure was studied during the reaction of methane oxidation. The pre-treatment with methane has different effect on the catalytic activities of both the oxides. The methane pre-treatment has not resulted in the change of the catalytic activity of BSCFO owing to its excellent reversibility of the perovskite structure resulting from the excellent synergistic interaction between Co and Fe in the oxide. However, the substitution with Ti on Fe-site in the lattice makes the methane pre-treatment have an obvious influence on the activity of the formed BSCTO oxide.

Síntese e caracterização de tungstatos de cério e estrôncio para fins catalíticos

The main goal of this work was to produce nanosized ceramic materials of the family of the tungstates (tungstates of cerium and strontium), and test them for their catalytic activity in processes involving the transformation of methane (CH4). The methodology used for the synthesis of the ceramic powders involved the complexation combining EDTA-citrate. The materials characterization was performed using simple and differential thermogravimetry, x-ray diffraction, transmission electron microscopy, and energy dispersive spectroscopy (EDS). The microstructure analysis was performed using the refinement by the Rietveld method, and the crystallite size and distribution of the materials was elucidate by the Scherrer and Williamson-Hall methods. The conditions of the synthesis process for the three envisaged materials (SrWO4, SrWO4 using tungsten oxide concentrate as raw material, and Ce2(WO4)3) were adjusted to obtain a single phase crystalline material. The catalytic tests were carried out in the presence of methane and synthetic air, which is composed of 21% O2 and 79% N2. The analysis of the conversion of the reaction was done with the aid of an fourier transform infrared device (FTIR). The analysis showed that, structurally, the SrWO4 produced using raw materials of high and poor purity (99% and 92%, respectively) are similar. The ideal parameters of calcination, in the tested range, are temperature of 1000 °C and time of calcination 5 hours. For the Ce2(WO4)3, the ideal calcination time and are temperature 15 hours and 1000°C, respectively. The Williamson-Hall method provided two different distributions for the crystallite size of each material, whose values ranged between the nanometer and micrometer scales. According to method of Scherrer, all materials produced were composed of nanometric crystallites. The analyses of transmission electron microscopy confirmed the results obtained from the Williamson- Hall method for the crystallite size. The EDS showed an atomic composition for the metals in the SrWO4 that was different of the theoretical composition. With respect to the catalytic tests, all materials were found to be catalytically active, but the reaction process should be further studied and optimized.

Estudo dos óxidos A2B2O7 e ABO3 a base de terras raras, para aplicações térmicas e catalíticas a altas temperaturas

Rare earth elements have recently been involved in a range of advanced technologies like microelectronics, membranes for catalytic conversion and applications in gas sensors. In the family of rare earth elements like cerium can play a key role in such industrial applications. However, the high cost of these materials and the control and efficiencies associated processes required for its use in advanced technologies, are a permanent obstacle to its industrial development. In present study was proposed the creation of phases based on rare earth elements that can be used because of its thermal behavior, ionic conduction and catalytic properties. This way were studied two types of structure (ABO3 and A2B2O7), the basis of rare earths, observing their transport properties of ionic and electronic, as well as their catalytic applications in the treatment of methane. For the process of obtaining the first structure, a new synthesis method based on the use of EDTA citrate mixture was used to develop a precursor, which undergone heat treatment at 950 ° C resulted in the development of submicron phase BaCeO3 powders. The catalytic activity of perovskite begins at 450 ° C to achieve complete conversion at 675 ° C, where at this temperature, the catalytic efficiency of the phase is maximum. The evolution of conductivity with temperature for the perovskite phase revealed a series of electrical changes strongly correlated with structural transitions known in the literature. Finally, we can establish a real correlation between the high catalytic activity observed around the temperature of 650 ° C and increasing the oxygen ionic conductivity. For the second structure, showed clearly that it is possible, through chemical processes optimized to separate the rare earth elements and synthesize a pyrochlore phase TR2Ce2O7 particular formula. This "extracted phase" can be obtained directly at low cost, based on complex systems made of natural minerals and tailings, such as monazite. Moreover, this method is applied to matters of "no cost", which is the case of waste, making a preparation method of phases useful for high technology applications

Síntese e caracterização de pós Ba(x)Sr(1-x)Co0,8Fe0,2O3- através do método de coprecipitação via oxalato

Ceramic powders based on oxides of perovskite-type structure is of fundamental interest nowadays, since they have important ionic-electronic conductivity in the use of materials with technological applications such as gas sensors, oxygen permeation membranes, catalysts and electrolytes for solid oxide fuel cells (SOFC). The main objective of the project is to develop nanostructured ceramic compounds quaternary-based oxide Barium (Br), Strontium (Sr), Cobalt (Co) and Iron (Fe). In this project were synthesized compounds BaxSr(1-x)Co0, 8Fe0,2O3- (x = 0.2, 0.5 and 0.8) through the oxalate co-precipitation method. The synthesized powders were characterized by thermogravimetric analysis and differential thermal analysis (TGADTA), X-ray diffraction (XRD) with the Rietveld refinement using the software MAUD and scanning electron microscopy (SEM). The results showed that the synthesis technique used was suitable for production of nanostructured ceramic solid solutions. The powders obtained had a crystalline phase with perovskite-type structure. The TGA-DTA results showed that the homogeneous phase of interest was obtained temperature above 1034°C. It was also observed that the heating rate of the calcination process did not affect the elimination of impurities present in the ceramic powder. The variation in the addition of barium dopant promoted changes in the average crystallite size in the nanometer range, the composition being BSCF(5582) obtained the lowest value (179.0nm). The results obtained by oxalate co-precipitation method were compared with those synthesis methods in solid state and EDTA-citrate method

Síntese e caracterização da cerâmica de [BaZr0,1Ce0,7Y0,1Yb0,1O3-δ] para uso como eletrólito de Células a Combustível de Cerâmicas Protônicas (PCFCs)

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Ba0.5Sr0.5Co0.8Fe0.2O3-delta ceramic hollow-fiber membranes for oxygen permeation

Setf-supported asymmetric hollow-fiber membranes of mixed oxygen-ionic and electronic conducting perovskite Ba0.5Sr0.5Co0.8Fe0.2O3-delta (BSCF) were prepared by a combined phase-inversion and sintering technique. The starting inorganic powder was synthesized by combined EDTA-citrate complexing process followed by thermal treatment at 600 degrees C. The powder was dispersed in a polymer solution and then extruded into hollow-fiber precursors through a spinneret. ne fiber precursors were sintered at elevated temperatures to form gastight membranes, which were characterized by SEM and gas permeation tests. Performance of the hollow fibers in air separation was both experimentally and theoretically studied at various conditions. The results reveal that the oxygen permeation process was controlled by the slow oxygen surface exchange kinetics under the investigated conditions. The porous inner surface of the prepared perovskite hollow-fiber membranes considerably favored the oxygen permeation. The maximum oxygen flux measured was 0.031 mol-m(-2).s(-1) at 950 degrees C with the sweep gas flow rate of 0.522 mol(.)m(-2).s(-1). To improve the oxygen flux of BSCF perovskite membranes, future work should be focused on surface modification rather than reduction of the membrane thickness. (c) 2006 American Institute of Chemical Engineers.

Desenvolvimento de material BaCexPr1-xO3 (0 ≤ X ≤ 1) com estrutura perovskita para oxidação catalítica do CO a CO2 em reator de leito fixo

Barium Cerate (BaCeO3) is perovskite type structure of ABO3, wherein A and B are metal cations. These materials, or doped, have been studied by having characteristics that make them promising for the application in fuel cells solid oxide, hydrogen and oxygen permeation, as catalysts, etc .. However, as the ceramic materials mixed conductivity have been produced by different synthesis methods, some conditions directly influence the final properties, one of the most important doping Site B, which may have direct influence on the crystallite size, which in turn directly influences their catalytic activity. In this study, perovskite-type (BaCexO3) had cerium gradually replaced by praseodymium to obtain ternary type materials BaCexPr1-xO3 and BaPrO3 binaries. These materials were synthesized by EDTA/Citrate complexing method and the material characterized via XRD, SEM and BET for the identification of their structure, morphology and surface area. Moreover were performed on all materials, catalytic test in a fixed bed reactor for the identification of that person responsible for complete conversion of CO to CO2 at low operating temperature, which step can be used as the subsequent production of synthesis gas (CO + H2) from methane oxidation. In the present work the crystalline phase having the orthorhombic structure was obtained for all compositions, with a morphology consisting of agglomerated particles being more pronounced with increasing praseodymium in the crystal structure. The average crystal size was between 100 nm and 142,2 nm. The surface areas were 2,62 m²g-1 for the BaCeO3 composition, 3,03 m²g-1 to BaCe0,5Pr0,5O3 composition and 2,37 m²g-1 to BaPrO3 composition. Regarding the catalytic tests, we can conclude that the optimal flow reactor operation was 50 ml / min and the composition regarding the maximum rate of conversion to the lowest temperature was BaCeO3 to 400° C. Meanwhile, there was found that the partially replaced by praseodymium, cerium, there was a decrease in the catalytic activity of the material.

Détermination de la spéciation du samarium dans l'environnement

Les éléments de terres rares (REEs) sont de plus en plus utilisés dans une multitude d’applications, notamment la fabrication d’aimants, de batteries rechargeables et les écrans de téléviseurs. Ils sont pour la plupart des métaux trivalents peu solubles dans les eaux naturelles. Comme pour les métaux divalents, le risque écologique des REEs est très probablement étroitement lié à leurs spéciations chimiques. Cependant, le comportement du samarium (Sm) dans les matrices environnementales est très peu connu et il n'existe actuellement aucune technique pour évaluer sa spéciation chimique. Dans cette optique, la technique d'échange d'ions (IET) sur la résine Dowex a été optimisée pour mesurer le samarium libre en solution. Les temps d'équilibre ont d'abord été déterminés pour des solutions tamponnées de samarium (Sm 6,7x10-8 M ; MES 1,0 mM M ; pH 6,0) en présence du nitrate de sodium (de 0,01M à 0,5 M). Pour ces diverses forces ioniques, l’équilibre thermodynamique n’est atteint que pour NaNO3 0,5M. Un autre mode d’utilisation de la résine (mode dynamique) a donc été développé pour tenir compte des conditions environnementales et évaluer efficacement le samarium libre. Les impacts des ligands organiques tels le NTA, l’EDTA, le citrate, l’acide malique et l’acide fulvique Suwannee River Standard I (SRFA) ont été étudiés par l’IET en mode dynamique. Une grande corrélation a été trouvée plus entre les taux d’accumulation de samarium sur la résine d’échange pour différents rapports NTA : Sm, EDTA : Sm, SRFA : Sm et le samarium libre. Par contre, aucune corrélation significative n’a été observée pour les ligands citrate et acide malique compte tenu des complexes qu’ils forment avec le samarium et qui s’adsorbent aussi sur la résine Dowex. Les concentrations Sm3+ mesurées par la technique IET ont été fortement corrélées avec celles prédites par le modèle WHAM 7.0 en utilisant la constante de stabilité obtenue par titration de SRFA par extinction de la fluorescence. Par ailleurs, la formation de colloïdes de samarium en fonction du pH influe grandement sur la détermination du samarium libre et doit être prise en compte dans la spéciation du samarium. L'IET assisté par des techniques auxiliaires comme le dosage par extinction de la fluorescence et le SP-ICPMS pourrait être une technique utile pour évaluer les concentrations de Sm biodisponible dans les eaux naturelles.

Détermination de la spéciation du samarium dans l'environnement

Les éléments de terres rares (REEs) sont de plus en plus utilisés dans une multitude d’applications, notamment la fabrication d’aimants, de batteries rechargeables et les écrans de téléviseurs. Ils sont pour la plupart des métaux trivalents peu solubles dans les eaux naturelles. Comme pour les métaux divalents, le risque écologique des REEs est très probablement étroitement lié à leurs spéciations chimiques. Cependant, le comportement du samarium (Sm) dans les matrices environnementales est très peu connu et il n'existe actuellement aucune technique pour évaluer sa spéciation chimique. Dans cette optique, la technique d'échange d'ions (IET) sur la résine Dowex a été optimisée pour mesurer le samarium libre en solution. Les temps d'équilibre ont d'abord été déterminés pour des solutions tamponnées de samarium (Sm 6,7x10-8 M ; MES 1,0 mM M ; pH 6,0) en présence du nitrate de sodium (de 0,01M à 0,5 M). Pour ces diverses forces ioniques, l’équilibre thermodynamique n’est atteint que pour NaNO3 0,5M. Un autre mode d’utilisation de la résine (mode dynamique) a donc été développé pour tenir compte des conditions environnementales et évaluer efficacement le samarium libre. Les impacts des ligands organiques tels le NTA, l’EDTA, le citrate, l’acide malique et l’acide fulvique Suwannee River Standard I (SRFA) ont été étudiés par l’IET en mode dynamique. Une grande corrélation a été trouvée plus entre les taux d’accumulation de samarium sur la résine d’échange pour différents rapports NTA : Sm, EDTA : Sm, SRFA : Sm et le samarium libre. Par contre, aucune corrélation significative n’a été observée pour les ligands citrate et acide malique compte tenu des complexes qu’ils forment avec le samarium et qui s’adsorbent aussi sur la résine Dowex. Les concentrations Sm3+ mesurées par la technique IET ont été fortement corrélées avec celles prédites par le modèle WHAM 7.0 en utilisant la constante de stabilité obtenue par titration de SRFA par extinction de la fluorescence. Par ailleurs, la formation de colloïdes de samarium en fonction du pH influe grandement sur la détermination du samarium libre et doit être prise en compte dans la spéciation du samarium. L'IET assisté par des techniques auxiliaires comme le dosage par extinction de la fluorescence et le SP-ICPMS pourrait être une technique utile pour évaluer les concentrations de Sm biodisponible dans les eaux naturelles.

Effects of EDTA and Sodium Citrate on hormone measurements by fluorometric (FIA) and immunofluorometric (IFMA) methods

Abstract Background Measurements of hormonal concentrations by immunoassays using fluorescent tracer substance (Eu3+) are susceptible to the action of chemical agents that may cause alterations in its original structure. Our goal was to verify the effect of two types of anticoagulants in the hormone assays performed by fluorometric (FIA) or immunofluorometric (IFMA) methods. Methods Blood samples were obtained from 30 outpatients and were drawn in EDTA, sodium citrate, and serum separation Vacutainer®Blood Collection Tubes. Samples were analyzed in automatized equipment AutoDelfia™ (Perkin Elmer Brazil, Wallac, Finland) for the following hormones: Luteinizing hormone (LH), Follicle stimulating homone (FSH), prolactin (PRL), growth hormone (GH), Sex hormone binding globulin (SHBG), thyroid stimulating hormone (TSH), insulin, C peptide, total T3, total T4, free T4, estradiol, progesterone, testosterone, and cortisol. Statistical analysis was carried out by Kruskal-Wallis method and Dunn's test. Results No significant differences were seen between samples for LH, FSH, PRL and free T4. Results from GH, TSH, insulin, C peptide, SHBG, total T3, total T4, estradiol, testosterone, cortisol, and progesterone were significant different between serum and EDTA-treated samples groups. Differences were also identified between serum and sodium citrate-treated samples in the analysis for TSH, insulin, total T3, estradiol, testosterone and progesterone. Conclusions We conclude that the hormonal analysis carried through by FIA or IFMA are susceptible to the effects of anticoagulants in the biological material collected that vary depending on the type of assay.

Glucose and citrate reduce the permeability changes caused by indomethacin in humans

Nonsteroidal anti-inflammatory drug (NSAID)-induced increased intestinal permeability appears to be a prerequisite for NSAID enteropathy. It has been suggested that early metabolic events leading to the permeability changes may involve inhibition of glycolysis and the tricarboxylic acid cycle, in which case the coadministration of glucose and citrate (the substrates for these metabolic pathways) with indomethacin may afford some protection. The present study, using a combined intestinal absorption-permeability test including 3-O-methyl-D-glucose, D-xylose, L-rhamnose, and [51Cr]ethylene-diaminetetraacetic acid (EDTA) as test probes and the differential urine excretion ratio of [51Cr]-EDTA/L-rhamnose, showed that indomethacin (50 + 75 mg) increased intestinal permeability. A formulation of indomethacin containing 15 mg glucose and 15 mg citrate to each milligram of indomethacin did not increase intestinal permeability significantly above baseline values. When given alone with indomethacin, neither glucose nor citrate (45 mg to each milligram of indomethacin) had any protective effects. Pharmokinetic studies showed that the effects of glucose and citrate cannot be explained on the basis of altered drug absorption. These results suggest a new approach to reducing the small intestinal side effects of NSAIDs.