Linearization of Drucker-Prager yield criterion for axisymmetric problems: implementation in lower-bound limit analysis

The linearization of the Drucker-Prager yield criterion associated with an axisymmetric problem has been achieved by simulating a sphere with the truncated icosahedron with 32 faces and 60 vertices. On this basis, a numerical formulation has been proposed for solving an axisymmetric stability problem with the usage of the lower-bound limit analysis, finite elements, and linear optimization. To compare the results, the linearization of the Mohr-Coulomb yield criterion, by replacing the three cones with interior polyhedron, as proposed earlier by Pastor and Turgeman for an axisymmetric problem, has also been implemented. The two formulations have been applied for determining the collapse loads for a circular footing resting on a cohesive-friction material with nonzero unit weight. The computational results are found to be quite convincing. (C) 2013 American Society of Civil Engineers.

Lower Bound Axisymmetric Limit Analysis Using Drucker-Prager Yield Cone and Simulation with Mohr-Coulomb Pyramid

This paper presents a lower bound limit analysis approach for solving an axisymmetric stability problem by using the Drucker-Prager (D-P) yield cone in conjunction with finite elements and nonlinear optimization. In principal stress space, the tip of the yield cone has been smoothened by applying the hyperbolic approximation. The nonlinear optimization has been performed by employing an interior point method based on the logarithmic barrier function. A new proposal has also been given to simulate the D-P yield cone with the Mohr-Coulomb hexagonal yield pyramid. For the sake of illustration, bearing capacity factors N-c, N-q and N-gamma have been computed, as a function of phi, both for smooth and rough circular foundations. The results obtained from the analysis compare quite well with the solutions reported from literature.

Ajuste del modelo de Drucker Prager extendido para la simulación de la respuesta mecánica de un vertisol mediante el método de elementos finitos

La mecanización de las labores del suelo es la causa, por su consumo energético e impacto directo sobre el medio ambiente, que más afecta a la degradación y pérdida de productividad de los suelos. Entre los factores de disminución de la productividad se deben considerar la compactación, la erosión, el encostramiento y la pérdida de estructura. Todo esto obliga a cuidar el manejo agrícola de los suelos tratando de mejorar las condiciones del suelo y elevar sus rendimientos sin comprometer aspectos económicos, ecológicos y ambientales. En el presente trabajo se adecuan los parámetros constitutivos del modelo de Drucker Prager Extendido (DPE) que definen la fricción y la dilatancia del suelo en la fase de deformación plástica, para minimizar los errores en las predicciones durante la simulación de la respuesta mecánica de un Vertisol mediante el Método de Elementos Finitos. Para lo cual inicialmente se analizaron las bases teóricas que soportan este modelo, se determinaron las propiedades y parámetros físico-mecánicos del suelo requeridos como datos de entrada por el modelo, se determinó la exactitud de este modelo en las predicciones de la respuesta mecánica del suelo, se estimaron mediante el método de aproximación de funciones de Levenberg-Marquardt los parámetros constitutivos que definen la trayectoria de la curva esfuerzo-deformación plástica. Finalmente se comprobó la exactitud de las predicciones a partir de las adecuaciones realizadas al modelo. Los resultados permitieron determinar las propiedades y parámetros del suelo, requeridos como datos de entrada por el modelo, mostrando que su magnitud está en función su estado de humedad y densidad, además se obtuvieron los modelos empíricos de estas relaciones exhibiendo un R2>94%. Se definieron las variables que provocan las inexactitudes del modelo constitutivo (ángulo de fricción y dilatancia), mostrando que las mismas están relacionadas con la etapa de falla y deformación plástica. Finalmente se estimaron los valores óptimos de estos ángulos, disminuyendo los errores en las predicciones del modelo DPE por debajo del 4,35% haciéndelo adecuado para la simulación de la respuesta mecánica del suelo investigado. ABSTRACT The mechanization using farming techniques is one of the main factors that affects the most the soil, causing its degradation and loss of productivity, because of its energy consumption and direct impact on the environment. Compaction, erosion, crusting and loss of structure should be considered among the factors that decrease productivity. All this forces the necessity to take care of the agricultural-land management trying to improve soil conditions and increase yields without compromising economic, ecological and environmental aspects. The present study was aimed to adjust the parameters of the Drucker-Prager Extended Model (DPE), defining friction and dilation of soil in plastic deformation phase, in order to minimize the error of prediction when simulating the mechanical response of a Vertisol through the fine element method. First of all the theoretic fundamentals that withstand the model were analyzed. The properties and physical-mechanical parameters of the soil needed as input data to initialize the model, were established. And the precision of the predictions for the mechanical response of the soil was assessed. Then the constitutive parameters which define the path of the plastic stress-strain curve were estimated through Levenberg-Marquardt method of function approximations. Lastly the accuracy of the predictions from the adequacies made to the model was tested. The results permitted to determine those properties and parameters of the soil, needed in order to initialize the model. It showed that their magnitude is in function of density and humidity. Moreover, the empirical models from these relations were obtained: R2>94%. The variables producing inaccuracies in the constitutive model (angle of repose and dilation) were defined, and there was showed that they are linked with the plastic deformation and rupture point. Finally the optimal values of these angles were established, obtaining thereafter error values for the DPE model under 4, 35%, and making it suitable for the simulation of the mechanical response of the soil under study.

A finite element approach for predicting the ultimate rotation capacity of RC beams

This paper presents a numerical approach to model the complex failure mechanisms that define the ultimate rotational capacity of reinforced concrete beams. The behavior in tension and compression is described by a constitutive damage model derived from a combination of two specific damage models [1]. The nonlinear behavior of the compressed region is treated by the compressive damage model based on the Drucker-Prager criterion written in terms of the effective stresses. The tensile damage model employs a failure criterion based on the strain energy associated with the positive part the effective stress tensor. This model is used to describe the behavior of very thin bands of strain localization, which are embedded in finite elements to represent multiple cracks that occur in the tensioned region [2]. The softening law establishes dissipation energy compatible with the fracture energy of the concrete. The reinforcing steel bars are modeled by truss elements with elastic-perfect plastic behavior. It is shown that the resulting approach is able to predict the different stages of the collapse mechanism of beams with distinct sizes and reinforcement ratios. The tensile damage model and the finite element embedded crack approach are able to describe the stiffness reduction due to concrete cracking in the tensile zone. The truss elements are able to reproduce the effects of steel yielding and, finally, the compressive damage model is able to describe the non-linear behavior of the compressive zone until the complete collapse of the beam due to crushing of concrete. The proposed approach is able to predict well the plastic rotation capacity of tested beams [3], including size-scale effects.

The effect of friction on indenter force and pile-up in numerical simulations of bone nanoindentation

Nanoindentation is a useful technique for probing the mechanical properties of bone, and finite element (FE) modeling of the indentation allows inverse determination of elasto-plastic constitutive properties. However, FE simulations to date have assumed frictionless contact between indenter and bone. The aim of this study was to explore the effect of friction in simulations of bone nanoindentation. Two dimensional axisymmetric FE simulations were performed using a spheroconical indenter of tip radius 0.6m and angle 90°. The coefficient of friction between indenter and bone was varied between 0.0 (frictionless) and 0.3. Isotropic linear elasticity was used in all simulations, with bone elastic modulus E=13.56GPa and Poisson’s ratio =0.3. Plasticity was incorporated using both Drucker-Prager and von Mises yield surfaces. Friction had a modest effect on the predicted force-indentation curve for both von Mises and Drucker-Prager plasticity, reducing maximum indenter displacement by 10% and 20% respectively as friction coefficient was increased from zero to 0.3 (at a maximum indenter force of 5mN). However, friction has a much greater effect on predicted pile-up after indentation, reducing predicted pile-up from 0.27m to 0.11m with a von Mises model, and from 0.09m to 0.02m with Drucker-Prager plasticity. We conclude that it is important to include friction in nanoindentation simulations of bone.

The effect of friction on indenter force and pile-up in numerical simulations of bone nanoindentation

Nanoindentation is a useful technique for probing the mechanical properties of bone, and finite element (FE) modeling of the indentation allows inverse determination of elasto-plastic constitutive properties. However, all but one FE study to date have assumed frictionless contact between indenter and bone. The aim of this study was to explore the effect of friction in simulations of bone nanoindentation. Two dimensional axisymmetric FE simulations were performed using a spheroconical indenter of tip radius 0.6 m and angle 90°. The coefficient of friction between indenter and bone was varied between 0.0 (frictionless) and 0.3. Isotropic linear elasticity was used in all simulations, with bone elastic modulus E=13.56GPa and Poisson‟s ratio f 0.3. Plasticity was incorporated using both Drucker-Prager and von Mises yield surfaces. Friction had a modest effect on the predicted force-indentation curve for both von Mises and Drucker-Prager plasticity, reducing maximum indenter displacement by 10% and 20% respectively as friction coefficient was increased from zero to 0.3 (at a maximum indenter force of 5mN). However, friction has a much greater effect on predicted pile-up after indentation, reducing predicted pile-up from 0.27 to 0.11 m with a von Mises model, and from 0.09 to 0.02 m with Drucker-Prager plasticity. We conclude that it is potentially important to include friction in nanoindentation simulations of bone if pile-up is used to compare simulation results with experiment.

Numerical prediction of load-displacement behaviors of adhesively bonded joints at different extension rates and temperatures

The present work focuses on simulation of nonlinear mechanical behaviors of adhesively bonded DLS (double lap shear) joints for variable extension rates and temperatures using the implicit ABAQUS solver. Load-displacement curves of DLS joints at nine combinations of extension rates and environmental temperatures are initially obtained by conducting tensile tests in a UTM. The joint specimens are made from dual phase (DP) steel coupons bonded with a rubber-toughened adhesive. It is shown that the shell-solid model of a DLS joint, in which substrates are modeled with shell elements and adhesive with solid elements, can effectively predict the mechanical behavior of the joint. Exponent Drucker-Prager or Von Mises yield criterion together with nonlinear isotropic hardening is used for the simulation of DLS joint tests. It has been found that at a low temperature (-20 degrees C), both Von Mises and exponent Drucker-Prager criteria give close prediction of experimental load-extension curves. However. at a high temperature (82 degrees C), Von Mises condition tends to yield a perceptibly softer joint behavior, while the corresponding response obtained using exponent Drucker-Prager criterion is much closer to the experimental load-displacement curve.

A finite element analysis of quasistatic crack growth in a pressure sensitive constrained ductile layer

Polymeric adhesive layers are employed for bonding two components in a wide variety of technological applications, It has been observed that, unlike in metals, the yield behavior of polymers is affected by the state of hydrostatic stress. In this work, the effect of pressure sensitivity of yielding and layer thickness on quasistatic interfacial crack growth in a ductile adhesive layer is investigated. To this end, finite deformation, finite element analyses of a cracked sandwiched layer are carried out under plane strain, small-scale yielding conditions for a wide range of mode mixities. The Drucker-Prager constitutive equations are employed to represent the behavior of the layer. Crack propagation is simulated through a cohesive zone model, in which the interface is assumed to follow a prescribed traction-separation law. The results show that for a given mode mixity, the steady state Fracture toughness [K](ss) is enhanced as the degree of pressure sensitivity increases. Further, for a given level of pressure sensitivity, [K](ss) increases steeply as mode Il loading is approached. (C) 2000 Elsevier Science Ltd. All rights reserved.

Solving Axisymmetric Stability Problems by Using Upper Bound Finite Elements, Limit Analysis, and Linear Optimization

A numerical formulation has been proposed for solving an axisymmetric stability problem in geomechanics with upper bound limit analysis, finite elements, and linear optimization. The Drucker-Prager yield criterion is linearized by simulating a sphere with a circumscribed truncated icosahedron. The analysis considers only the velocities and plastic multiplier rates, not the stresses, as the basic unknowns. The formulation is simple to implement, and it has been employed for finding the collapse loads of a circular footing placed over the surface of a cohesive-frictional material. The formulation can be used to solve any general axisymmetric geomechanics stability problem.

爆炸排淤填石法中岩土介质的本构模型

以爆炸排淤填石法为背景，对相关岩土介质的本构模型进行了探讨。分析认为，在以LS.DYNA 动态有限元分析程序对爆炸排淤填石法的数值模拟中，岩土介质不适于采用Mohr.Coulomb 模型，堆石体宜采用Drucker-Prager 模型，淤泥宜采用Prandtl-Reuss 模型；利用LS-DYNA 程序对淤泥的本构模型进行了验证和确认，计算表明：在形成爆炸空腔的高应变率阶段，淤泥表现为理想不可压缩流体的性质；在小药量小抵抗线条件下，在淤泥自重作用下的低应变率变形阶段，其粘性效应可以忽略不计。

三维弹塑性模型在桩端土体性状分析中的应用

用三维弹塑性模型分析桩端部土体的性状。首先,将半元限土体中的轴对称问题归结为求解双调和方程,运用Hankel变换可以给出圆型均布载荷作用下的解析解。而后,使用德鲁克—普拉格(Drucker-Prager)准则分析土介质塑性屈服的性状。本文在给出解析解的同时,用电子计算机计算了泊桑比v=1/4±介质中的位移场。二者比较,结果十分接近。在上述分析的基础上建立了“刚性圆锥”的力学模型,并给出了形成“刚性圆锥”的临界载荷与圆锥顶角对土性参数依赖关系的计算公式。

海底管线地基土体塑性及剪切破坏分析

提出一种分析管线地基极限承载力的平面应变有限元模拟方法,采用自适应网格技术和接触对算法模拟管线嵌入土体的准静态过程,利用修正Drucker-Prager/Cap本构模型模拟土体塑性。研究不同土性和管土界面摩擦条件下,管线地基土体的塑性变形及位移场特性。利用载荷沉降曲线并结合地基塑性应变分布图和位移矢量图,可判别管线地基的剪切破坏型式、确定地基极限承载力。

Analysis and modeling of heaping behavior of granular mixtures within a computational mechanics framework

This paper presents a continuum model of the flow of granular material during filling of a silo, using a viscoplastic constitutive relation based on the Drucker-Prager plasticity yield function. The performed simulations demonstrate the ability of the model to realistically represent complex features of granular flows during filling processes, such as heap formation and non-zero inclination angle of the bulk material-air interface. In addition, micro-mechanical parametrizations which account for particle size segregation are incorporated into the model. It is found that numerical predictions of segregation phenomena during filling of a binary granular mixture agree well with experimental results. Further numerical tests indicate the capability of the model to cope successfully with complex operations involving granular mixtures.

A computational study of segregation in granular material during heaping

A continuum model of the flow of granular material during silo filling using a viscoplastic constitutive relation is presented in this paper. The constitutive model is based on the Drucker-Prager plasticity yield function. The simulation results give a realistic representation of complex features of granular flows during filling processes, such as heap formation and non-zero inclination angle of the material-air interface. The model is also coupled within the same framework with novel micro-mechanical parametrisations and the process of segregation during filling of granular mixtures can also be modelled.