Control system for actuation and sensing in digital microfluidics devices

Digital Microfluidics (DMF) is a second generation technique, derived from the conventional microfluidics that instead of using continuous liquid fluxes, it uses only individual droplets driven by external electric signals. In this thesis a new DMF control/sensing system for visualization, droplet control (movement, dispensing, merging and splitting) and real time impedance measurement have been developed. The software for the proposed system was implemented in MATLAB with a graphical user interface. An Arduino was used as control board and dedicated circuits for voltage switching and contacts were designed and implemented in printed circuit boards. A high resolution camera was integrated for visualization. In our new approach, the DMF chips are driven by a dual-tone signal where the sum of two independent ac signals (one for droplet operations and the other for impedance sensing) is applied to the electrodes, and afterwards independently evaluated by a lock-in amplifier. With this new approach we were able to choose the appropriated amplitudes and frequencies for the different proposes (actuation and sensing). The measurements made were used to evaluate the real time droplet impedance enabling the knowledge of its position and velocity. This new approach opens new possibilities for impedance sensing and feedback control in DMF devices.

A comparison of the performance and biological efficiency of new knapsack sprayers and a controlled droplet application (CDA) sprayer for the control of the diamondback moth, Plutella xylostella L. (Lepidoptera : Plutellidae)

Field trials and laboratory bioassays were undertaken to compare the performance and efficacy (mortality of diamondback moth larvae) of insecticides applied to cabbages with three high volume hydraulic knapsack sprayers (NS-16, PB-20 and Selecta 12V) and a controlled droplet application (CDA) sprayer. In field experiments, the high volume knapsack sprayers (application rate 500-600 L ha(-1)) provided better spray coverage on the upper and lower surfaces of inner leaves, the upper surfaces of middle and outer leaves, and greater biological efficacy than the CDA sprayer (application rate 20similar to40 L ha(-1)). The PB-20 provided better spray coverage on the upper surface of middle leaves and both surfaces of outer leaves when compared with the Selecta 12V. However, its biological efficacy in the field was not significantly different from that of the other high volume sprayers. Increasing the application rate from 20 to 40 L ha(-1) for the CDA sprayer significantly increased droplet density but had no impact on test insect mortality. Laboratory evaluations of biological efficacy yielded higher estimates than field evaluations and there was no significant difference between the performance of the PB-20 and the CDA sprayer. Significant positive relationships were detected between insect mortality and droplet density deposited for both the PB-20 and the CDA sprayers.

Dose response relationship of droplet applications for the leaf-specific weed control in vegetable crops

As a prelude to leaf-specific weed control using droplets targeted by a robotic weeder, amounts of herbicide required to control individual weed seedlings were estimated. Roundup Biactive was applied at doses equivalent to 1/128th to four times the recommended rate in addition to undiluted Roundup and water controls. Based on the mean ground cover of the seedlings, the recommended dose (1.5 l ha 1) was estimated and droplets were applied to individual plants by micropipette. All treatments contained 1% AS 500 SL, Agromix (adjuvant). Three weeks after application dry weights (DW) of each seedling was recorded. DW reductions of 50% were achieved in the five species tested at less than the recommended rate whereas only in one species was a 90% reduction obtained at that rate. In Galium aparine for example, 19.3 μg of glyphosate reduced DW per plant by 90% compared to the recommended dose of 8.4 μg.

Droplet deposition during spray and leaf pH in aquatic weed control

A diversidade morfológica da superfície foliar existente entre as espécies de plantas e a presença de estruturas foliares como tricomas, estômatos, cutícula e ceras podem exercer grande influência na aderência e deposição das gotas de pulverização, assim como na absorção do herbicida. Desta forma, o objetivo do presente trabalho foi estudar, em quatro espécies de plantas daninhas aquáticas (Enhydra anagallis, Eichhornia crassipes, Heteranthera reniformis e Typha subulata), a área de molhamento de gotas de pulverização nas superfícies foliares adaxial e abaxial, bem como o pH foliar. O experimento foi realizado em Botucatu-SP. As plantas foram cultivadas em caixas d'água sob condições de campo, e quando atingiram seu pleno desenvolvimento (antes do florescimento), foram realizadas as avaliações de pH foliar e da área de molhamento de gotas de pulverização. As tensões superficiais das gotas aplicadas (0,5 mL), apresentadas pelas soluções de glyphosate aplicado isolado a 5,0% v v-1 (Rodeo 480 g L-1 e.a. produto comercial), glyphosate + Aterbane BR (5,0% + 0,5% v v-1), glyphosate + Silwet L-77 (5,0% + 0,05% v v-1), além das soluções com os adjuvantes isolados, Aterbane BR (0,5% v v-1) e Silwet L-77 (0,05% v v-1) foram respectivamente 72,1; 28,7; 23,3; 37,3 e 22,1 mN m-1. As médias obtidas de pH foliar variaram entre 5,50 e 7,50, destacando-se a espécie E. anagallis com valores de 6,68 e 7,02 para as faces adaxial e abaxial, respectivamente. Dentre as plantas daninhas aquáticas avaliadas T. subulata foi a espécie que apresentou as maiores médias de área de molhamento nas faces adaxial e abaxial da folha, proporcionada pelas as soluções de glyphosate + Aterbane BR, glyphosate + Silwet L-77 e Silwet L-77, com valores de 12,99-7,03; 20,04-17,95 e 31,81-25,91 mm², respectivamente.

Acyl-CoA synthetase 3 promotes lipid droplet biogenesis in ER microdomains.

Control of lipid droplet (LD) nucleation and copy number are critical, yet poorly understood, processes. We use model peptides that shift from the endoplasmic reticulum (ER) to LDs in response to fatty acids to characterize the initial steps of LD formation occurring in lipid-starved cells. Initially, arriving lipids are rapidly packed in LDs that are resistant to starvation (pre-LDs). Pre-LDs are restricted ER microdomains with a stable core of neutral lipids. Subsequently, a first round of"emerging" LDs is nucleated, providing additional lipid storage capacity. Finally, in proportion to lipid concentration, new rounds of LDs progressively assemble. Confocal microscopy and electron tomography suggest that emerging LDs are nucleated in a limited number of ER microdomains after a synchronized stepwise process of protein gathering, lipid packaging, and recognition by Plin3 and Plin2. A comparative analysis demonstrates that the acyl-CoA synthetase 3 is recruited early to the assembly sites, where it is required for efficient LD nucleation and lipid storage.

Acyl-CoA synthetase 3 promotes lipid droplet biogenesis in ER microdomains.

Control of lipid droplet (LD) nucleation and copy number are critical, yet poorly understood, processes. We use model peptides that shift from the endoplasmic reticulum (ER) to LDs in response to fatty acids to characterize the initial steps of LD formation occurring in lipid-starved cells. Initially, arriving lipids are rapidly packed in LDs that are resistant to starvation (pre-LDs). Pre-LDs are restricted ER microdomains with a stable core of neutral lipids. Subsequently, a first round of"emerging" LDs is nucleated, providing additional lipid storage capacity. Finally, in proportion to lipid concentration, new rounds of LDs progressively assemble. Confocal microscopy and electron tomography suggest that emerging LDs are nucleated in a limited number of ER microdomains after a synchronized stepwise process of protein gathering, lipid packaging, and recognition by Plin3 and Plin2. A comparative analysis demonstrates that the acyl-CoA synthetase 3 is recruited early to the assembly sites, where it is required for efficient LD nucleation and lipid storage.

Distribution pattern, surface tension and contact angle of herbicides associated to adjuvants on spraying and control of Ipomoea hederifolia under rainfall incidence

ABSTRACTScarlet Morning Glory is considered to be an infesting weed that affects several crops and causes serious damage. The application of chemical herbicides, which is the primary control method, requires a broad knowledge of the various characteristics of the solution and application technology for a more efficient phytosanitary treatment. Therefore this study aimed to characterize the effect of rainfall incidence on the control of Ipomoea hederifolia, considering droplet size, surface tension, contact angle of droplets formed by herbicides liquid on vegetal and artificial surfaces, associated to adjuvants and the volumetric distribution profile of the spray jet. The addition of the adjuvants to the herbicide spraying liquid improved the application quality, as it influenced the angle formed by the spray by broadening the deposition band of the spray nozzle and thus the possible distance between the nozzles on spray boom and due the changes at droplet size, which contribute to a safety application. The rainfall occurrence affected negatively the weed control with the different spraying liquids and also the dry matter weight, suggesting that the phytosanitary product applied was washed off.

Application Volumes and Sizes of Droplets for the Application of Diquat Herbicide in the Control of Eichhornia crassipes

The objective of this study was to evaluate the efficiency of application and the efficacy of control of water hyacinth (Eichhornia crassipes) with the use of the diquat herbicide done with two application volumes associated to three droplets classes. Three experiments were conducted; in the first, the application efficiency was evaluated; in the second, the control efficiency and; in the third, the droplet spectrum. They were conducted in a completely randomized design with five, four and six replicates, respectively. The treatments were arranged in a 2 x 3 factorial design, with two application volumes (100 and 200 L ha-1) and three droplets classes (fine, extremely coarse and ultra-coarse) to the first and second experiment and the third comprised two diquat concentrations in spray solution (2 and 4 g i.a. L-1) and three droplets classes (fine, extremely coarse and ultra-coarse). The application efficiency was determined by the coverage by droplets, spray deposition and active ingredient of the herbicide (diquat). The efficacy was measured by the control and the percentage of plants with regrowth at 50 days after application. The spectrum of droplets produced per each nozzle model used to obtain the droplets classes were analyzed. According to the parameters analyzed, using the droplets classes extremely thick and ultra thick can provide greater certainty in the application of diquat in the aquatic environment associated with the deposition of the active and sufficient coverage to control Eichhornia crassipes with both application volumes

Control of nanomaterial self-assembly in ultrasonically levitated droplets

We demonstrate that acoustic trapping can be used to levitate and manipulate droplets of soft matter, in particular, lyotropic mesophases formed from selfassembly of different surfactants and lipids, which can be analyzed in a contact-less manner by X-ray scattering in a controlled gas-phase environment. On the macroscopic length scale, the dimensions and the orientation of the particle are shaped by the ultrasonic field, while on the microscopic length scale the nanostructure can be controlled by varying the humidity of the atmosphere around the droplet. We demonstrate levitation and in situ phase transitions of micellar, hexagonal, bicontinuous cubic, and lamellar phases. The technique opens up a wide range of new experimental approaches of fundamental importance for environmental, biological, and chemical research.

Precision emulsification for droplet and capsule production

Emulsions and microcapsules are typical structures in various dispersion formulations for pharmaceutical, food, personal and house care applications. Precise control over size and size distribution of emulsion droplets and microcapsules are important for effective use and delivery of active components and better product quality. Many emulsification technologies have been developed to meet different formulation and processing requirements. Among them, membrane and microfluidic emulsification as emerging technologies have the feature of being able to precisely manufacture droplets in a drop-by-drop manner to give subscribed sizes and size distributions with lower energy consumption. This paper reviews fundamental sciences and engineering aspects of emulsification, membrane and microfluidic emulsification technologies and their use for precision manufacture of emulsions for intensified processing. Generic application examples are given for single and double emulsions and microcapsules with different structure features. © 2013 The Society of Powder Technology Japan. Published by Elsevier B.V.

Continuous property measurement techniques and physics based mathematical model for frost growth control

The development of a new set of frost property measurement techniques to be used in the control of frost growth and defrosting processes in refrigeration systems was investigated. Holographic interferometry and infrared thermometry were used to measure the temperature of the frost-air interface, while a beam element load sensor was used to obtain the weight of a deposited frost layer. The proposed measurement techniques were tested for the cases of natural and forced convection, and the characteristic charts were obtained for a set of operational conditions. ^ An improvement of existing frost growth mathematical models was also investigated. The early stage of frost nucleation was commonly not considered in these models and instead an initial value of layer thickness and porosity was regularly assumed. A nucleation model to obtain the droplet diameter and surface porosity at the end of the early frosting period was developed. The drop-wise early condensation in a cold flat plate under natural convection to a hot (room temperature) and humid air was modeled. A nucleation rate was found, and the relation of heat to mass transfer (Lewis number) was obtained. It was found that the Lewis number was much smaller than unity, which is the standard value usually assumed for most frosting numerical models. The nucleation model was validated against available experimental data for the early nucleation and full growth stages of the frosting process. ^ The combination of frost top temperature and weight variation signals can now be used to control the defrosting timing and the developed early nucleation model can now be used to simulate the entire process of frost growth in any surface material. ^