Classificação Automática de Modulação Digital com uso de Correntropia para Ambientes de Rádio Cognitivo

Modern wireless systems employ adaptive techniques to provide high throughput while observing desired coverage, Quality of Service (QoS) and capacity. An alternative to further enhance data rate is to apply cognitive radio concepts, where a system is able to exploit unused spectrum on existing licensed bands by sensing the spectrum and opportunistically access unused portions. Techniques like Automatic Modulation Classification (AMC) could help or be vital for such scenarios. Usually, AMC implementations rely on some form of signal pre-processing, which may introduce a high computational cost or make assumptions about the received signal which may not hold (e.g. Gaussianity of noise). This work proposes a new method to perform AMC which uses a similarity measure from the Information Theoretic Learning (ITL) framework, known as correntropy coefficient. It is capable of extracting similarity measurements over a pair of random processes using higher order statistics, yielding in better similarity estimations than by using e.g. correlation coefficient. Experiments carried out by means of computer simulation show that the technique proposed in this paper presents a high rate success in classification of digital modulation, even in the presence of additive white gaussian noise (AWGN)

Digitally-implemented naturally sampled PWM suitable for multilevel converter control

For dynamic closed loop control of a multilevel converter with a low pulse number (ratio of switching frequency to synthesized fundamental), natural sampled pulse-width modulation (PWM) is the best form of modulation. Natural sampling does not introduce distortion or a delayed response to the modulating signal. However previous natural sampled PWM implementations have generally been analog. For a modular multilevel converter, a digital implementation has advantages of accuracy and flexibility. Re-sampled uniform PWM is a novel digital modulation technique which approaches the performance of natural PWM. Both hardware and software implementations for a five level multilevel converter phase are presented, demonstrating the improvement over uniform PWM.

1.55 µm High-Speed QDs Lasers for Optical Telecommunication Applications

In this work investigation of the QDs formation and the fabrication of QD based semiconductor lasers for telecom applications are presented. InAs QDs grown on AlGaInAs lattice matched to InP substrates are used to fabricate lasers operating at 1.55 µm, which is the central wavelength for far distance data transmission. This wavelength is used due to its minimum attenuation in standard glass fibers. The incorporation of QDs in this material system is more complicated in comparison to InAs QDs in the GaAs system. Due to smaller lattice mismatch the formation of circular QDs, elongated QDs and quantum wires is possible. The influence of the different growth conditions, such as the growth temperature, beam equivalent pressure, amount of deposited material on the formation of the QDs is investigated. It was already demonstrated that the formation process of QDs can be changed by the arsenic species. The formation of more round shaped QDs was observed during the growth of QDs with As2, while for As4 dash-like QDs. In this work only As2 was used for the QD growth. Different growth parameters were investigated to optimize the optical properties, like photoluminescence linewidth, and to implement those QD ensembles into laser structures as active medium. By the implementation of those QDs into laser structures a full width at half maximum (FWHM) of 30 meV was achieved. Another part of the research includes the investigation of the influence of the layer design of lasers on its lasing properties. QD lasers were demonstrated with a modal gain of more than 10 cm-1 per QD layer. Another achievement is the large signal modulation with a maximum data rate of 15 Gbit/s. The implementation of optimized QDs in the laser structure allows to increase the modal gain up to 12 cm-1 per QD layer. A reduction of the waveguide layer thickness leads to a shorter transport time of the carriers into the active region and as a result a data rate up to 22 Gbit/s was achieved, which is so far the highest digital modulation rate obtained with any 1.55 µm QD laser. The implementation of etch stop layers into the laser structure provide the possibility to fabricate feedback gratings with well defined geometries for the realization of DFB lasers. These DFB lasers were fabricated by using a combination of dry and wet etching. Single mode operation at 1.55 µm with a high side mode suppression ratio of 50 dB was achieved.

Modelado de la propagación acústica submarina para comunicaciones PtP

El objetivo principal del proyecto es el desarrollo de un simulador de comunicaciones submarinas, que permite la caracterización del canal a través de datos reales que son usados para establecer la comunicación entre dos puntos, empleando diferentes técnicas de modulación. Dicho simulador, ofrece un interfaz gráfico sencillo de usar y ha sido desarrollado en MatLab, basado en Bellhop [14] y Simulink. Dicho simulador desarrollado se ha usado para realizar simulaciones en diferentes escenarios, con datos reales del océano extraídos de la base de datos WOD [2]. Se ha divido el proyecto en seis partes: INTRODUCCIÓN, MARCO TEÓRICO, IMPLEMENTACIÓN, CONCLUSIONES, MANUAL y PROPUESTA DE PRÁCTICA. Se describen a continuación: En la primera parte, se realiza una introducción al proyecto, indicando las motivaciones que llevaron a desarrollarlo, una breve introducción, los objetivos fijados y un análisis de la evolución histórica de las comunicaciones submarinas, hasta llegar al estado del arte existente. En la segunda parte se describen los fundamentos teóricos necesarios para el desarrollo del proyecto, por una parte lo relativo a las ondas acústicas y su propagación, y por otra lo relativo a las técnicas de modulación digital empleadas. En la tercera parte se describe la implementación del simulador, explicando las funcionalidades existentes y un resumen de cómo fue desarrollado y su arquitectura lo que facilita su uso para proyectos futuros. La cuarta parte analiza las simulaciones realizadas en diversos escenarios, empleando datos reales y datos artificiales para la temperatura y salinidad del agua. En la quinta parte se proporciona un manual de usuario del simulador desarrollado, para que pueda ser usado correctamente. Se describe también el procesado de extracción de datos de WOD para que sean compatibles. Por último, en propuesta didáctica se propone un guión de práctica para desarrollar en la asignatura P.A.S. ABSTRACT. The main goal of this project is the development of an underwater communication simulator, that allows the determination of the underwater channel through real data, using different modulation techniques. The simulator, offers a graphic interface, easy to use and developed in MatLab, based on Bellhop [14] and Simulink. The simulator was given the name of UWACOMSIM and it was used to simulate different scenarios, using data from the WOD [2]. The project is divided into six parts: INTRODUCTION, THEORETICAL FRAMEWORK, IMPLEMENTATION, CONCLUSIONS, MANUAL and DIDACTAL PROPOSAL. These parts are described bellow: In the first part an introduction is given, remarking the motivations that lead to develop the project. Also objectives are explained, a historical analysis of the underwater communications is given, and finish with the state of the art. Secondly, theoretical part is described. First, everything related with acoustics and wave propagation throgh water, secondly, digital modulation techniques are explained. In the third part, the simulation implementation is explained. Main functionalities are highlighted and a brief overview of the architecture is given. This part can be useful for related works. Simulations and conclusions about the results, are done in the fourth part. In this section, different significant scenarios are chosen, and many simulations are launched in order to analyse the data. In the fifth parth, a user manual is provided in order to show the user how to use the simulator and how to download data from WOD if needed. In the final part of the project, a laboratory session is proposed for the subject P.A.S.

Notes on analogue and digital amplitude modulation

Notes on AM, DSBSC, QAM, BPSK, 4QAM, 8PSK, 16QAM

Are distortion levels a problem with digital signal processing hearing aids and frequency modulation (FM) systems?

The purpose of this study was to examine objective and subjective distortion present when frequency modulation (FM) systems were coupled with four digital signal processing (DSP) hearing aids. Electroacoustic analysis and subjective listening tests by experienced audiologists revealed that distortion levels varied across hearing aids and channels.

Digital Coherent Receivers and Advanced Optical Modulation Formats in 100 and 200 Gb/s DWDM Systems

Recent advances in coherent optical receivers is reviewed. Digital-Signal-Processing (DSP) based phase and polarization management techniques make coherent detection robust and feasible. With coherent detection, the complex field of the received optical signal is fully recovered, allowing compensation of linear and nonlinear optical impairments including chromatic dispersion (CD) and polarization-mode dispersion (PMD) using digital filters. Coherent detection and advanced optical modulation formats have become a key ingredient to the design of modern dense wavelength-division multiplexed (DWDM) optical broadband networks. In this paper, firstly we present the different subsystems of a digital coherent optical receiver, and secondly, we will compare the performance of some multi-level and multi-dimensional modulation formats in some physical impairments and in high spectral-efficiency (SE) and high-capacity DWDM transmissions, simulating the DSP with Matlab and the optical network performance with OptiSystem software.

A new joint coding and modulation scheme for channels with clipping

A major limitation in any high-performance digital communication system is the linearity region of the transmitting amplifier. Nonlinearities typically lead to signal clipping. Efficient communication in such conditions requires maintaining a low peak-to-average power ratio (PAR) in the transmitted signal while achieving a high throughput of data. Excessive PAR leads either to frequent clipping or to inadequate resolution in the analog-to-digital or digital-to-analog converters. Currently proposed signaling schemes for future generation wireless communications suffer from a high PAR. This paper presents a new signaling scheme for channels with clipping which achieves a PAR as low as 3. For a given linear range in the transmitter's digital-to-analog converter, this scheme achieves a lower bit-error rate than existing multicarrier schemes, owing to increased separation between constellation points. We present the theoretical basis for this new scheme, approximations for the expected bit-error rate, and simulation results. (C) 2002 Elsevier Science (USA).

Digital radiography detector performance

The characterization of physical properties of digital imaging systems requires the determination and measurement of detectors’ physical performance. Those measures such as modulation transfer function (MTF), noise power spectra (NPS), and detective quantum efficiency (DQE) provide objective evaluations of digital detectors’ performance. To provide an MTF, NPS, and DQE calculation from raw-data images it is necessary to implement a method that is undertaken by two major steps: (1) image acquisition and (2) quantitative measure determination method. In this chapter a comprehensive description about a method to provide the measure of performance of digital radiography detectors is provided.

Modulation of Ca 2+ dependent inactivation of Ca 2+ channels by intracellular signalling

Magdeburg, Univ., Fak. für Naturwiss., Diss., 2009

Modulation des kanonischen Wnt/[Beta]-Catenin-Signalweges in der Helicobacter pylori-Infektion

Magdeburg, Univ., Fak. für Naturwiss., Diss., 2010

Modulation of the activity of the mitochondrial BK-channel and the permeability transition pore by hypoxia and apoptotic factors

Magdeburg, Univ., Fak. für Naturwiss., Diss., 2010

Modulation of [My]-opioid receptor signal transduction and endocytosis by ADP-ribosylation factor proteins

Magdeburg, Univ., Fak. für Naturwiss., Diss., 2010

Modulation funktioneller Plastizität in der hippokampalen CA1 Region der frei beweglichen Ratte

Magdeburg, Univ., Fak. für Naturwiss., Diss., 2011