Noise Figure Measurement of Differential Amplifiers Using non-Ideal Baluns

This paper analyzes the noise and gain measurement of microwave differential amplifiers using two passive baluns. A general model of the baluns is considered, including potential losses and phase/amplitude unbalances. This analysis allows de-embedding the actual gain and noise performance of the isolated amplifier by using single-ended measurements of the cascaded system and baluns. Finally, measured results from two amplifier prototypes are used to validate the theoretical principles.

Differential amplifier with improved gain-accuracy and linearity

A novel circuit design technique is presented which improves gain-accuracy and linearity in differential amplifiers. The technique employs negative impedance compensation and results demonstrate a significant performance improvement in precision, lowering sensitivity, and wide dynamic range. A theoretical underpinning is given together with the results of a demonstrator differential input/output amplifier with gain of 12 dB. The simulation results show that, with the novel method, both the gain-accuracy and linearity can be improved greatly. Especially, the linearity improvement in IMD can get to more than 23 dB with a required gain.

A De-Embedding Method to Characterize Differential

This paper analyses the noise and gain measurement of microwave differential amplifiers using two passive baluns. A model of the baluns that includes potential losses and unbalances has been considered. This analysis allows to de-embed the actual performance of the differential device from the single-ended measurements of the two-port cascaded system and the baluns. The method has been validated with measured results from a fully-differential amplifier prototype.

Design and application of a differential photo amplifier.

Thesis (M.S.)--University of Illinois.

High sensitivity low cost capacitive strain gage

This paper describes a high senstivity low cost capacitive strain gage sensor. The theory, design, and sensor construction details are presented. It consists of eight capacitive sensors connected in two full bridges. The capacitive strain gage sensor structure was designed in order to produce high sensitivity and low dependence with temperature. By using a simple signal conditioning circuit constituted by a differential amplifier, a band-pass filter, and a precision rectifier the device can measure forces with resolution of 0.009 N and precision of 98.7%. It is rugged, presents linear response, and good repeatability. It presents sensitivity of 8.7 V/N and fall time of 12 ms.

Método de desembebido para la caracterización de amplificadores diferenciales usando baluns pasivos

This paper analyses the noise and gain measurement of microwave differential amplifiers using two passive baluns. A model of the baluns that includes potential losses and unbalances has been considered. This analysis allows de-embedding actual performance of the differential device from the single-ended measurements of the two-port cascaded system and the baluns. The method has been validated with measured results from a fully-differential amplifier prototype.

Thermal stability and spectroscopic properties of Er3+-doped niobium tellurite glasses for broadband amplifiers

Three Er3+-doped tellurite glasses with compositions of 70TeO(2)-30ZnO, 70TeO(2)-20ZnO-10Nb(2)O(5) and 70TeO(2)-20ZnO-5BaO-5Nb(2)O(5) have been investigated for developing fiber and planar broadband amplifiers and lasers. The optical spectroscopic properties and thermal stability of Er3+-doped tellurite glasses have been discussed. The results show that the incorporation of Nb2O5 increases the thermal stability of Er3+-doped tellurite glasses significantly, Er3+-doped niobium tellurite glasses 70TeO(2)-20ZnO-10Nb(2)O(5) and 70TeO(2)-20ZnO-5BaO-5Nb(2)O(5) exhibit the good thermal stability (DeltaT > 150degreesC), the large emission cross-section (>10 x 10(-21) cm(2)) and broad full width at half maximum (similar to65 nm), will be preferable for broadband Er3+-doped fiber amplifiers. (C) 2004 Elsevier B.V. All rights reserved.

Numerical and theoretical analysis of the crosstalk in linear optical amplifiers

The dynamic characteristics, including the crosstalk and relaxation oscillation, of linear optical amplifiers (LOAs) are investigated by small-signal analysis under an averaging carrier density approximation and compared with the results of numerical simulation. The good agreement between the numerical simulation and the small-signal analysis indicated the averaging carrier density is an appropriate approximation for analyzing LOAs. Theoretical analyzes also show that the dynamic properties of the vertical laser fields dominate the dynamic performance of LOAs. Based on the small-signal analysis, a concise equation for the crosstalk under high bit rate was derived, which can be applied to measure the differential gain of LOAs.

Broadband active differential array for the mid-frequency SKA band

This paper presents the design and characterization process of an active array demonstrator for the mid-frequency range (i.e., 300 MHz-1000 MHz) of the future Square Kilometre Array (SKA) radio telescope. This demonstrator, called FIDA3 (FG-IGN: Fundación General Instituto Geográfico Nacional - Differential Active Antenna Array), is part of the Spanish contribution for the SKA project. The main advantages provided by this design include the use of a dielectric-free structure, and the use of a fully-differential receiver in which differential low-noise amplifiers (LNAs) are directly connected to the balanced tapered-slot antennas (TSAs). First, the radiating structure and the differential low-noise amplifiers were separately designed and measured, obtaining good results (antenna elements with low voltage standing-wave ratios, array scanning capabilities up to 45°, and noise temperatures better than 52 K with low-noise amplifiers at room temperature). The potential problems due to the differential nature of the proposed solution are discussed, so some effective methods to overcome such limitations are proposed. Second, the complete active antenna array receiving system was assembled, and a 1 m2 active antenna array tile was characterized.

RZ-DPSK transmission at 80 Gbit/s channel rate using in-line semiconductor optical amplifiers

We numerically demonstrate the feasibility of return-to-zero differential phase-shift keying transmission at 8.0 Gbit/s channel rate using cascaded in-line semiconductor optical amplifiers.

RZ-DPSK transmission at 80 Gbit/s channel rate using in-line semiconductor optical amplifiers

We numerically demonstrate the feasibility of return-to-zero differential phase-shift keying transmission at 80 Gbit/s channel rate using cascaded in-line semiconductor optical amplifiers.

RZ-DPSK transmission at 80 Gbit/s channel rate using in-line semiconductor optical amplifiers

We numerically demonstrate the feasibility of return-to-zero differential phase-shift keying transmission at 80 Gbit/s channel rate using cascaded in-line semiconductor optical amplifiers.