Experimental study on bridge damage identification based on wavelet packet energy curvature difference method

Among those damage identification methods, the Wavelet Packet Energy Curvature Difference (WPECD) Method is an effective one. However, most of the existing methods rely on numerical simulation and are unverified via experiment, and very few of them have been applied to practice. In this paper, the validity of WPECD in structural damage identification is verified by a numerical example. A damage simulation experiment is taken on a real replaced girder at the Ziya River New Bridge in Cangzhou. Two damage cases are applied and the acceleration responses at the measuring points are obtained, based on which the damages are identified with the WPECD Method, and the influence of wavelet function and decomposition level is studied. The results show that the WPECD Method can identify structure damage efficiently and can be put into practice.

The variate difference method,

Commission's seal on t.-p.

Efetividade dos instrumentos de políticas públicas nos gastos privados de P&D no Brasil

Esse trabalho teve como objetivo contribuir para o debate sobre a importância das políticas de incentivo à inovação no Brasil. Os resultados esperados do uso que as empresas fizeram dos diferentes tipos de instrumentos sobre os gastos em pesquisa e desenvolvimento (P&D) foram avaliados pelo método de diferenças em diferenças. O método permitiu obter as diferenças de gastos entre empresas beneficiárias de instrumentos e as não-beneficiárias em três períodos consecutivos: 2005 em relação à 2003; 2008 em relação à 2005 e de 2011 em relação à 2008. Ao fazer isso, foi possível identificar se tais diferenças foram positivas e significativas, podendo ser atribuídas às influências dos instrumentos. Os instrumentos utilizados foram: incentivos fiscais, Lei de Informática, financiamentos em parcerias, financiamentos sem parcerias e subvenção. E a utilização dos mesmos pelas empresas teve maior relevância no âmbito de diversos programas de apoio à inovação vigentes no país a partir da retomada das políticas industriais e tecnológicas, nos anos 2000. O estudo concluiu que os efeitos positivos e significativos são limitados à determinados grupos tecnológicos e à poucos instrumentos, em geral, de caráter fiscal. Além disso, esses efeitos positivos surgem em apenas um período, sendo que para cada grupo tecnológico foram efetuadas estimativas para três períodos. Também não houve evidências de que os instrumentos financeiros exerçam efeitos significativos sobre as decisões de gastos em pesquisa e desenvolvimento, apesar da maior ênfase dada aos mesmos no período estudado. Os resultados sugerem fraca influência dos mecanismos de apoio à P&D no Brasil sobre o aumento dos gastos privados, apesar dos avanços recentes.

Valores da pressão arterial em cães pelos métodos oscilométrico e Doppler vascular

Foram comparados dois métodos não-invasivos de medida da pressão arterial, o Doppler vascular e o oscilométrico, com o objetivo de estabelecer parâmetros que possam auxiliar no diagnóstico seguro da hipertensão arterial. Para tal, foram utilizados 45 cães, machos e fêmeas, distribuídos em três grupos de acordo com o peso, pequeno, médio e grande porte. Em cada animal, procedeu-se a mensuração por meio do Doppler vascular e, em seguida, do oscilométrico. Na obtenção da pressão arterial sistólica, não houve diferença entre os métodos nos três grupos de animais, porém, na obtenção da pressão arterial diastólica, houve diferença estatística entre o Doppler vascular e o oscilométrico nos grupos de animais de pequeno e médio porte. Pôde-se concluir que valores confiáveis de pressão sistólica podem ser obtidos tanto por meio do Doppler vascular quanto do oscilométrico. Os valores da pressão arterial diastólica obtidos pelos dois métodos não se correlacionam, principalmente nos animais de pequeno e médio porte.

Solution of a heterogeneous modeling of a horizontal-flow anaerobic immobilized biomass (HAIB) reactor by the sequencing method

A modeling study was completed to develop a methodology that combines the sequencing and finite difference methods for the simulation of a heterogeneous model of a tubular reactor applied in the treatment of wastewater. The system included a liquid phase (convection diffusion transport) and a solid phase (diffusion reaction) that was obtained by completing a mass balance in the reactor and in the particle, respectively. The model was solved using a pilot-scale horizontal-flow anaerobic immobilized biomass (HAIB) reactor to treat domestic sewage, with the concentration results compared with the experimental data. A comparison of the behavior of the liquid phase concentration profile and the experimental results indicated that both the numerical methods offer a good description of the behavior of the concentration along the reactor. The advantage of the sequencing method over the finite difference method is that it is easier to apply and requires less computational time to model the dynamic simulation of outlet response of HAIB.

Geomorphological method in the elaboration of hazard maps for flash-floods in the municipality of Jucuarán (El Salvador)

This work deals with the elaboration of flood hazard maps. These maps reflect the areas prone to floods based on the effects of Hurricane Mitch in the Municipality of Jucuarán of El Salvador. Stream channels located in the coastal range in the SE of El Salvador flow into the Pacific Ocean and generate alluvial fans. Communities often inhabit these fans can be affected by floods. The geomorphology of these stream basins is associated with small areas, steep slopes, well developed regolite and extensive deforestation. These features play a key role in the generation of flash-floods. This zone lacks comprehensive rainfall data and gauging stations. The most detailed topographic maps are on a scale of 1:25 000. Given that the scale was not sufficiently detailed, we used aerial photographs enlarged to the scale of 1:8000. The effects of Hurricane Mitch mapped on these photographs were regarded as the reference event. Flood maps have a dual purpose (1) community emergency plans, (2) regional land use planning carried out by local authorities. The geomorphological method is based on mapping the geomorphological evidence (alluvial fans, preferential stream channels, erosion and sedimentation, man-made terraces). Following the interpretation of the photographs this information was validated on the field and complemented by eyewitness reports such as the height of water and flow typology. In addition, community workshops were organized to obtain information about the evolution and the impact of the phenomena. The superimposition of this information enables us to obtain a comprehensive geomorphological map. Another aim of the study was the calculation of the peak discharge using the Manning and the paleohydraulic methods and estimates based on geomorphologic criterion. The results were compared with those obtained using the rational method. Significant differences in the order of magnitude of the calculated discharges were noted. The rational method underestimated the results owing to short and discontinuous periods of rainfall data with the result that probabilistic equations cannot be applied. The Manning method yields a wide range of results because of its dependence on the roughness coefficient. The paleohydraulic method yielded higher values than the rational and Manning methods. However, it should be pointed out that it is possible that bigger boulders could have been moved had they existed. These discharge values are lower than those obtained by the geomorphological estimates, i.e. much closer to reality. The flood hazard maps were derived from the comprehensive geomorphological map. Three categories of hazard were established (very high, high and moderate) using flood energy, water height and velocity flow deduced from geomorphological and eyewitness reports.

Dynamic Model of a Small Once-Through Boiler

In this study, a model for the unsteady dynamic behaviour of a once-through counter flow boiler that uses an organic working fluid is presented. The boiler is a compact waste-heat boiler without a furnace and it has a preheater, a vaporiser and a superheater. The relative lengths of the boiler parts vary with the operating conditions since they are all parts of a single tube. The present research is a part of a study on the unsteady dynamics of an organic Rankine cycle power plant and it will be a part of a dynamic process model. The boiler model is presented using a selected example case that uses toluene as the process fluid and flue gas from natural gas combustion as the heat source. The dynamic behaviour of the boiler means transition from the steady initial state towards another steady state that corresponds to the changed process conditions. The solution method chosen was to find such a pressure of the process fluid that the mass of the process fluid in the boiler equals the mass calculated using the mass flows into and out of the boiler during a time step, using the finite difference method. A special method of fast calculation of the thermal properties has been used, because most of the calculation time is spent in calculating the fluid properties. The boiler was divided into elements. The values of the thermodynamic properties and mass flows were calculated in the nodes that connect the elements. Dynamic behaviour was limited to the process fluid and tube wall, and the heat source was regarded as to be steady. The elements that connect the preheater to thevaporiser and the vaporiser to the superheater were treated in a special way that takes into account a flexible change from one part to the other. The model consists of the calculation of the steady state initial distribution of the variables in the nodes, and the calculation of these nodal values in a dynamic state. The initial state of the boiler was received from a steady process model that isnot a part of the boiler model. The known boundary values that may vary during the dynamic calculation were the inlet temperature and mass flow rates of both the heat source and the process fluid. A brief examination of the oscillation around a steady state, the so-called Ledinegg instability, was done. This examination showed that the pressure drop in the boiler is a third degree polynomial of the mass flow rate, and the stability criterion is a second degree polynomial of the enthalpy change in the preheater. The numerical examination showed that oscillations did not exist in the example case. The dynamic boiler model was analysed for linear and step changes of the entering fluid temperatures and flow rates.The problem for verifying the correctness of the achieved results was that there was no possibility o compare them with measurements. This is why the only way was to determine whether the obtained results were intuitively reasonable and the results changed logically when the boundary conditions were changed. The numerical stability was checked in a test run in which there was no change in input values. The differences compared with the initial values were so small that the effects of numerical oscillations were negligible. The heat source side tests showed that the model gives results that are logical in the directions of the changes, and the order of magnitude of the timescale of changes is also as expected. The results of the tests on the process fluid side showed that the model gives reasonable results both on the temperature changes that cause small alterations in the process state and on mass flow rate changes causing very great alterations. The test runs showed that the dynamic model has no problems in calculating cases in which temperature of the entering heat source suddenly goes below that of the tube wall or the process fluid.

Solution of the Hartree-Fock equations for atoms and diatomic molecules with the finite element method

The finite element method (FEM) is now developed to solve two-dimensional Hartree-Fock (HF) equations for atoms and diatomic molecules. The method and its implementation is described and results are presented for the atoms Be, Ne and Ar as well as the diatomic molecules LiH, BH, N_2 and CO as examples. Total energies and eigenvalues calculated with the FEM on the HF-level are compared with results obtained with the numerical standard methods used for the solution of the one dimensional HF equations for atoms and for diatomic molecules with the traditional LCAO quantum chemical methods and the newly developed finite difference method on the HF-level. In general the accuracy increases from the LCAO - to the finite difference - to the finite element method.

Accurate Hartree-Fock-Slater calculations on small diatomic molecules with the finite-element method

We report on the self-consistent field solution of the Hartree-Fock-Slater equations using the finite-element method for the three small diatomic molecules N_2, BH and CO as examples. The quality of the results is not only better by two orders of magnitude than the fully numerical finite difference method of Laaksonen et al. but the method also requires a smaller number of grid points.

Gender differences in early accommodation and vergence development

A remote haploscopic photorefractor was used to assess objective binocular vergence and accommodation responses in 157 full-term healthy infants aged 1-6 months while fixating a brightly coloured target moving between fixation distances at 2, 1, 0.5 and 0.33 m. Vergence and accommodation response gain matured rapidly from 'flat' neonatal responses at an intercept of approximately 2 dioptres (D) for accommodation and 2.5 metre angles(MA) for vergence, reaching adult-like values at 4 months. Vergence gain was marginally higher in females (p = 0.064), but accommodation gain (p = 0.034) was higher and accommodative intercept closer to zero (p = 0.004) in males in the first 3 months as they relaxed accommodation more appropriately for distant targets. More females showed flat accommodation responses (p = 0.029). More males behaved hypermetropically in the first two months of life, but when these hypermetropic infants were excluded from the analysis, the gender difference remained. Gender differences disappeared after three months. Data showed variable responses and infants could behave appropriately and simultaneously on both, neither or only one measure at all ages. If accommodation was appropriate (gain between 0.7 and 1.3; r(2) > 0.7) but vergence was not, males over- and under-converged equally, while the females who accommodated appropriately were more likely to overconverge (p = 0.008). The apparent earlier maturity of the male accommodative responses may be due to refractive error differences but could also reflect gender-specific male preference for blur cues while females show earlier preference for disparity, which may underpin the earlier emerging, disparity dependent, stereopsis and full vergence found in females in other studies.

An implicit technique for solving 3D low Reynolds number moving free surface flows

This paper describes the development of an implicit finite difference method for solving transient three-dimensional incompressible free surface flows. To reduce the CPU time of explicit low-Reynolds number calculations, we have combined a projection method with an implicit technique for treating the pressure on the free surface. The projection method is employed to uncouple the velocity and the pressure fields, allowing each variable to be solved separately. We employ the normal stress condition on the free surface to derive an implicit technique for calculating the pressure at the free surface. Numerical results demonstrate that this modification is essential for the construction of methods that are more stable than those provided by discretizing the free surface explicitly. In addition, we show that the proposed method can be applied to viscoelastic fluids. Numerical results include the simulation of jet buckling and extrudate swell for Reynolds numbers in the range [0.01, 0.5]. (C) 2008 Elsevier Inc. All rights reserved.

Textual Differences in Game Reviews Written by Men and Women

The aim of this essay is to examine the differences in language use between the genders in game reviews, to find whether there are differences in the use of the language depending on gender. Both sexist language and technical aspects are examined, the technical aspects of writing have been chosen from previous research about gendered differences in writing. The reviews are randomly chosen but the games are selected. There is an equal amount of games with male and female main characters, and the number of reviews is chosen according to the number of reviews written by females, as there are fewer of them, and thus easier to find a matching number of reviews written by males rather than vice versa. The reviews are then examined to find sexist language and differences. This essay finds that there is sexist language in the writing of both genders, such as marked language, but only when the main character of the game is female. Both genders tend to focus on the appearance of female characters and the characteristics of male characters, but there is no known previous research about male and female game characters to compare these results to. However, the technical differences remain consistent with previous research on the same subject, such as female reviewers using more pronouns than male reviewers, and male reviewers using fewer verbs than female reviewers.

Critical points in logistic growth curves and treatment comparisons

Several biological phenomena have a behavior over time mathematically characterized by a strong increasing function in the early stages of development, then by a less pronounced growth, sometimes showing stability. The separation between these phases is very important to the researcher, since the maintenance of a less productive phase results in uneconomical activity. In this report we present methods of determining critical points in logistic functions that separate the early stages of growth from the asymptotic phase, with the aim of establishing a stopping critical point in the growth and on this basis determine differences in treatments. The logistic growth model is fitted to experimental data of imbibition of arariba seeds (Centrolobium tomentosum). To determine stopping critical points the following methods were used: i) accelerating growth function, ii) tangent at the inflection point, iii) segmented regression; iv) modified segmented regression; v) non-significant difference; and vi) non-significant difference by simulation. The analysis of variance of the abscissas and ordinates of the breakpoints was performed with the objective of comparing treatments and methods used to determine the critical points. The methods of segmented regression and of the tangent at the inflection point lead to early stopping points, in comparison with other methods, with proportions ordinate/asymptote lower than 0.90. The non-significant difference method by simulation had higher values of abscissas for stopping point, with an average proportion ordinate/asymptote equal to 0.986. An intermediate proportion of 0.908 was observed for the acceleration function method.

MORPHOLOGICAL CASTE DIFFERENCES IN POLYBIA AEQUATORIALIS (HYMENOPTERA: VESPIDAE: POLISTINAE: EPIPONINI), A SOCIAL WASP of THE HIGHLANDS of COSTA RICA

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Bose-Einstein condensation dynamics in three dimensions by the pseudospectral and finite-difference methods

We suggest a pseudospectral method for solving the three-dimensional time-dependent Gross-Pitaevskii (GP) equation, and use it to study the resonance dynamics of a trapped Bose-Einstein condensate induced by a periodic variation in the atomic scattering length. When the frequency of oscillation of the scattering length is an even multiple of one of the trapping frequencies along the x, y or z direction, the corresponding size of the condensate executes resonant oscillation. Using the concept of the differentiation matrix, the partial-differential GP equation is reduced to a set of coupled ordinary differential equations, which is solved by a fourth-order adaptive step-size control Runge-Kutta method. The pseudospectral method is contrasted with the finite-difference method for the same problem, where the time evolution is performed by the Crank-Nicholson algorithm. The latter method is illustrated to be more suitable for a three-dimensional standing-wave optical-lattice trapping potential.