A Comparison of Deep Drawing and Ironing of Metal Alloy Strip Produced conventionally and Non-conventionally via Semi Solid Material Processing

A semi solid thin strip continuous casting process was used to obtain 50%wt Pb/50%wtSn strip by single and twin roll processing at speed of 15 m/min. A 50%wt Pb/50%wtSn plate ingot was also cast for rolling conventionally into strips of 1.4 mm thickness and 45 mm width for comparison with those achieved non-conventionally. This hypoeutectic alloy has a solidification interval and fusion temperature of approximately 31 degrees C and 215 degrees C respectively. The casting alloy temperature was around 280 degrees C as measured by a type K immersion thermocouple prior to pouring into a tundish designed to maintain a constant melt flow on the cooling slope during semi solid material production. A nozzle with a weir ensures that the semi solid material is dragged smoothly by the lower roll, producing strip with minimum contamination of slag/oxide. The temperatures of the cooling slope and the lower roll were also monitored using K type thermocouples. The coiled semi solid strip, which has a thickness of 1.5 mm and 45 mm width, was rolled conventionally in order to obtain 1.2 mm thick strip. The coiled thixorolled strip had a thickness of 1.2 mm and achieved practically the same width as the conventional strips. Blanks of 40 mm diameter were cut from the strips in a mechanical press, ready for deep drawing and ironing for mechanical characterization. All the strips achieved from non-conventional processing had the same mechanical performance as those achieved conventionally. The limiting drawing ratio (LDR) achieved was approximately 2.0 for all strips. Microscopy examination was made in order to observe phase segregation during processing.

微碳深冲钢板的非｛111｝织构特征及其对r,△r值的影响

From St15 micro-carbon deep drawing steel sheets, two sets of samples with (r) over bar variant and Deltar constant, and (r) over bar constant and Deltar variant, were selected to carry out texture measurement and ODF analysis. A description of the texture characteristics and an investigation on the effect of the main textures on the (r) over bar and Deltar values were given. The results show that in the tested steel sheets no desired gamma < 111 > parallel to ND orientation line appears but gamma' orientation line located at <()over bar>=0-90 degrees, theta =19 degrees and phi =45 degrees, and L orientation line located around gamma < 111 > parallel to ND orientation line which spirally rotates from Psi =0 degrees, theta =54.7 degrees and phi =62.7 degrees to Psi =90 degrees, theta =40 degrees and phi =45 degrees occur. Among them, the L orientation line has a main influence on the (r) over bar value and the stronger the texture density, the higher the (r) over bar value is, but is somewhat detrimental to the Deltar value; at the same time, the gamma' orientation line has a major effect on the Deltar value in an opposite way, but is somewhat deteriorative to the (r) over bar value. A strong L orientation line superposed by a relatively strong gamma' orientation line may produce fine (r) over bar and Deltar values.

Blade design and forming for fans using finite elements

The necessity of adapting the standardized fan models to conditions of higher temperature has emerged due to the growth of concerning referring to the consequences of the gas expelling after the Mont Blanc tunnel accident in Italy and France, where even though, with 100 fans in operation, 41 people died. However, since then, the defied solutions have pointed to aerodynamic disadvantages or have seemed nonappropriate in these conditions. The objective of this work is to present an alternative to the market standard fans considering a new technology in constructing blades. This new technology introduces the use of the stainless steel AISI 409 due to its good adaptation to temperatures higher than 400°C, particularly exposed to temperatures of gas exhaust from tunnels in fire situation. Furthermore, it presents a very good resistance to corrosion and posterior welding and pressing, due to its alloyed elements. The innovation is centered in the process of a deep drawing of metallic shells and posterior welding, in order to keep the ideal aerodynamic superficies for the fan ideal performance. On the other hand, the finite element method, through the elasto-plastic software COSMOS permitted the verification of the thickness and structural stability of the blade in relation to the aerodynamic efforts established in the project. In addition, it is not advisable the fabrication of blades with variable localized thickness not even, non-uniform ones, due to the verified concentration of tensions and the difficulties observed in the forming. In this way, this study recommends the construction of blades with uniform variations of thickness. © 2007 Springer.

Fabricação e caracterização metalográfica e mecânica de tiras de ligas metálicas fundidas e tixolaminadas no estado semi-sólido de diferentes intervalos de solidificação

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Desenvolvimento de um programa paramétrico para simulação do processo de estampagem utilizando elementos finitos

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Análise da estampagem de chapas metálicas utilizando elementos finitos

Pós-graduação em Engenharia Mecânica - FEG

Análise da reversão do fundo de latas de alumínio para bebidas - Buckle

This work approaches the main methods of plastic deformation of metals, with a focus on the deep drawing process. The mechanical properties were evaluated with the tension tests. It is presented the aluminum alloys designation, followed by applying heat treatments and the designation of tempers. The manufacture of aluminum beverage cans is described step by step, in general terms. The main objective is to analyze how different cans background geometries have great influence on the dome reversal. To be able to achieve the goal it was necessary to use cans of different manufacturers, which were used in buckle tests to obtain the reversal pressures, tensile tests and geometric analysis. Finally empirical equations were obtained correlating these variables, and it was observed that the conformation of reforming change significantly it's behavior

Analysis of a Non-Traditional Micro Tube Hydroforming Process

As the demand for miniature products and components continues to increase, the need for manufacturing processes to provide these products and components has also increased. To meet this need, successful macroscale processes are being scaled down and applied at the microscale. Unfortunately, many challenges have been experienced when directly scaling down macro processes. Initially, frictional effects were believed to be the largest challenge encountered. However, in recent studies it has been found that the greatest challenge encountered has been with size effects. Size effect is a broad term that largely refers to the thickness of the material being formed and how this thickness directly affects the product dimensions and manufacturability. At the microscale, the thickness becomes critical due to the reduced number of grains. When surface contact between the forming tools and the material blanks occur at the macroscale, there is enough material (hundreds of layers of material grains) across the blank thickness to compensate for material flow and the effect of grain orientation. At the microscale, there may be under 10 grains across the blank thickness. With a decreased amount of grains across the thickness, the influence of the grain size, shape and orientation is significant. Any material defects (either natural occurring or ones that occur as a result of the material preparation) have a significant role in altering the forming potential. To date, various micro metal forming and micro materials testing equipment setups have been constructed at the Michigan Tech lab. Initially, the research focus was to create a micro deep drawing setup to potentially build micro sensor encapsulation housings. The research focus shifted to micro metal materials testing equipment setups. These include the construction and testing of the following setups: a micro mechanical bulge test, a micro sheet tension test (testing micro tensile bars), a micro strain analysis (with the use of optical lithography and chemical etching) and a micro sheet hydroforming bulge test. Recently, the focus has shifted to study a micro tube hydroforming process. The intent is to target fuel cells, medical, and sensor encapsulation applications. While the tube hydroforming process is widely understood at the macroscale, the microscale process also offers some significant challenges in terms of size effects. Current work is being conducted in applying direct current to enhance micro tube hydroforming formability. Initially, adding direct current to various metal forming operations has shown some phenomenal results. The focus of current research is to determine the validity of this process.

Estudio del efecto del procesamiento termo mecánico sobre los parámetros de formabilidad en aceros IF para aplicaciones automotrices

En el presente trabajo de investigación se analizó un acero libre de elementos intersticiales estabilizado con Titanio o mejor conocido como acero IF (por sus siglas en inglés Interstitial Free), denominado por la empresa EDDS (Extra Deep Drawing Steel) el cual se utiliza en partes exteriores de los vehículos en donde se requiere que la lámina a estampar cumpla con propiedades muy altas de ductilidad y baja resistencia. Se obtuvo acero IF en sus distintas etapas de procesamiento termo mecánico comenzando por material laminado en caliente, material laminado en frio y por ultimo material recocido y galvanizado en planta, esto con el objetivo de caracterizar y evaluar las propiedades mecánicas de cada etapa. De la etapa final del acero (recocido y galvanizado de planta) se obtuvieron los parámetros de formabilidad (n y R) mediante una prueba de tensión para poder establecer las condiciones a superar con las experimentaciones. El objetivo principal en el laboratorio fue el mejorar, mediante diferentes variables de recocido (tiempo y temperatura) en los tratamientos térmicos, los parámetros n= 0.23 y R=1.56 producidos en planta, y lograr obtener mediante nuevos tratamientos térmicos valores de R> 1.56 al igual que valores de n>0.23. Para simular las temperaturas con tiempos cortos de recocido se implementó un calentamiento por inducción en la bobina del laboratorio. Se pudieron realizar solo 2 pruebas debido al material disponible para este experimento. Ambos experimentos resultaron en una notable mejoría del valor de Lankford R (utilizado como un indicador en la formabilidad de hojas de acero), así como del exponente de endurecimiento por deformación (n), y se logró mantener un poco por encima sus propiedades de esfuerzo de cedencia, esfuerzo último y por ciento de elongación a las obtenidas por el proceso de recocido realizado en planta.

Small acts of resistance : the role of intergenerational collaborative drawing in early childhood teaching and learning

This chapter focuses on ‘intergenerational collaborative drawing’, a particular process of drawing whereby adults and children draw at the same time on a blank paper space. Such drawings can be produced for a range of purposes, and based on different curriculum or stimulus subjects. Children of all ages, and with a range of physical and intellectual abilities are able to draw with parents, carers and teachers. Intergenerational collaborative drawing is a highly potent method for drawing in early childhood contexts because it brings adults and children together in the process of thinking and theorizing in order to create visual imagery and this exposes in deep ways to adults and children, the ideas and concepts being learned about. For adults, this exposure to a child’s thinking is a far more effective assessment tool than when they are presented with a finished drawing they know little about. This chapter focuses on drawings to examine wider issues of learning independence and how in drawing, preferred schema in the form of hand-out worksheets, the suggestive drawings provided by adults, and visual material seen in everyday life all serve to co-opt a young child into making particular schematic choices. I suggest that intergenerational collaborative drawing therefore serves to work as a small act of resistance to that co-opting, in that it helps adults and children to collectively challenge popular creativity and learning discourses.

Res Communis? A critical legal geography of outer space, Antarctica, and the deep seabed

This chapter provides a critical legal geography of outer Space, charting the topography of the debates and struggles around its definition, management, and possession. As the emerging field of critical legal geography demonstrates, law is not a neutral organiser of space, but is instead a powerful cultural technology of spatial production. Drawing on legal documents such as the Outer Space Treaty and the Moon Treaty, as well as on the analogous and precedent-setting legal geographies of Antarctica and the deep seabed, the chapter addresses key questions about the legal geography of outer Space, questions which are of growing importance as Space’s available satellite spaces in the geostationary orbit diminish, Space weapons and mining become increasingly viable, Space colonisation and tourism emerge, and questions about Space’s legal status grow in intensity. Who owns outer Space? Who, and whose rules, govern what may or may not (literally) take place there? Is the geostationary orbit the sovereign property of the equatorial states it supertends, as these states argued in the 1970s? Or is it a part of the res communis, or common property of humanity, which currently legally characterises outer Space? Does Space belong to no one, or to everyone? As challenges to the existing legal spatiality of outer Space emerge from spacefaring states, companies, and non-spacefaring states, it is particularly critical that the current spatiality of Space is understood and considered.

The Systematics, Distribution and Bionomics of Deep sea fishes beyond depth 200m along the South west coast of India

Reducing fishing pressure in coastal waters is the need of the day in the Indian marine fisheries sector of the country which is fast changing from a mere vocational activity to a capital intensive industry. It requires continuous monitoring of the resource exploitation through a scientifically acceptable methodology, data on production of each species stock, the number and characteristics of the fishing gears of the fleet, various biological characteristics of each stock, the impact of fishing on the environment and the role of fishery—independent on availability and abundance. Besides this, there are issues relating to capabilities in stock assessment, taxonomy research, biodiversity, conservation and fisheries management. Generation of reliable data base over a fixed time frame, their analysis and interpretation are necessary before drawing conclusions on the stock size, maximum sustainable yield, maximum economic yield and to further implement various fishing regulatory measures. India being a signatory to several treaties and conventions, is obliged to carry out assessments of the exploited stocks and manage them at sustainable levels. Besides, the nation is bound by its obligation of protein food security to people and livelihood security to those engaged in marine fishing related activities. Also, there are regional variabilities in fishing technology and fishery resources. All these make it mandatory for India to continue and strengthen its marine capture fisheries research in general and deep sea fisheries in particular. Against this background, an attempt is made to strengthen the deep sea fish biodiversity and also to generate data on the distribution, abundance, catch per unit effort of fishery resources available beyond 200 m in the EEZ of southwest coast ofIndia and also unravel some of the aspects of life history traits of potentially important non conventional fish species inhabiting in the depth beyond 200 m. This study was carried out as part of the Project on Stock Assessment and Biology of Deep Sea Fishes of Indian EEZ (MoES, Govt. of India).

Box Corer (engineering detail drawing of the large version)

The Box corer is a marine geological and biological sampling tool for soft sediments in lakes or oceans. It is deployed from a research vessel with a deep sea wire and suitable for any water depth. It is designed for a minimum of disturbance of the sediment surface by bow wave effects which is important for quantitative investigations of the benthos micro- to macrofauna, geochemical processes, sampling of bottom water or sedimentology. The large box corer version with an area of 2,500 cm? is frequently used on research vessels since the 1980th years. This data set is a publication of the engeneering drawings.