Surface deformation studies of Tenerife Island, Spain from joint GPS-DInSAR observations

This work presents results for the three-dimensional displacement field at Tenerife Island calculated from campaign GPS and ascending and descending ENVISAT DInSAR interferograms. The goal of this work is to provide an example of the flexibility of the technique by fusing together new varieties of geodetic data, and to observe surface deformations and study precursors of potential activity in volcanic regions. Interferometric processing of ENVISAT data was performed with GAMMA software. All possible combinations were used to create interferograms and then stacking was used to increase signal-to-noise ratio. Decorrelated areas were widely observed, particularly for interferograms with large perpendicular baseline and large time span. Tropospheric signal was also observed which significantly complicated the interpretation. Subsidence signal was observed in the NW part of the island and around Mount Teide and agreed in some regions with campaign GPS data. It is expected that the technique will provide better results when more high quality DInSAR and GPS data is available

Advanced interpretation of subsidence in Murcia (SE Spain) using A-DInSAR data – modelling and validation

Subsidence is a natural hazard that affects wide areas in the world causing important economic costs annually. This phenomenon has occurred in the metropolitan area of Murcia City (SE Spain) as a result of groundwater overexploitation. In this work aquifer system subsidence is investigated using an advanced differential SAR interferometry remote sensing technique (A-DInSAR) called Stable Point Network (SPN). The SPN derived displacement results, mainly the velocity displacement maps and the time series of the displacement, reveal that in the period 2004–2008 the rate of subsidence in Murcia metropolitan area doubled with respect to the previous period from 1995 to 2005. The acceleration of the deformation phenomenon is explained by the drought period started in 2006. The comparison of the temporal evolution of the displacements measured with the extensometers and the SPN technique shows an average absolute error of 3.9±3.8 mm. Finally, results from a finite element model developed to simulate the recorded time history subsidence from known water table height changes compares well with the SPN displacement time series estimations. This result demonstrates the potential of A-DInSAR techniques to validate subsidence prediction models as an alternative to using instrumental ground based techniques for validation.

Relationship between piezometric level and ground deformations measured by means of DInSAR in the Vega Media of the Segura River (Spain)

Differential SAR Interferometry (DInSAR) is a remote sensing method with the well demonstrated ability to monitor geological hazards like earthquakes, landslides and subsidence. Among all these hazards, subsidence involves the settlement of the ground surface affecting wide areas. Frequently, subsidence is induced by overexploitation of aquifers and constitutes a common problem that affects developed societies. The excessive pumping of underground water decreases the piezometric level in the subsoil and, as a consequence, increases the effective stresses with depth causing a consolidation of the soil column. This consolidation originates a settlement of ground surface that must be withstood by civil structures built on these areas. In this paper we make use of an advanced DInSAR approach - the Coherent Pixels Technique (CPT) [1] - to monitor subsidence induced by aquifer overexploitation in the Vega Media of the Segura River (SE Spain) from 1993 to the present. 28 ERS-1/2 scenes covering a time interval of about 10 years were used to study this phenomenon. The deformation map retrieved with CPT technique shows settlements of up to 80 mm at some points of the studied zone. These values agree with data obtained by means of borehole extensometers, but not with the distribution of damaged buildings, well points and basements, because the occurrence of damages also depends on the structural quality of the buildings and their foundations. The most interesting relationship observed is the one existing between piezometric changes, settlement evolution and local geology. Three main patterns of ground surface and piezometric level behaviour have been distinguished for the study zone during this period: 1) areas where deformation occurs while ground conditions remain altered (recent deformable sediments), 2) areas with no deformation (old and non-deformable materials), and 3) areas where ground deformation mimics piezometric level changes (expansive soils). The temporal relationship between deformation patterns and soil characteristics has been analysed in this work, showing a delay between them. Moreover, this technique has allowed the measurement of ground subsidence for a period (1993-1995) where no instrument information was available.

DInSAR monitoring of aquifer compaction due to water withdrawal: Vegas Baja and Media of the Segura river (SE, Spain) case study

This study was partially financed by the Spanish Ministry of Education and Science and EU FEDER under project TEC2005-06863, by the Valencia Regional Government under projects GV006/179 and ACOMP07/087, and by the University of Alicante under projects VIGROB2004102, VIGROB-053, and VIGROB-114.

Monitorización de la subsidencia del terreno en la Vega Media del río Segura mediante Interferometría SAR diferencial (DInSAR)

Ground subsidence caused by aquifer exploitation is a geotechnical hazard that affects wide areas, causing important economic damages. This phenomenon is due to soil consolidation produced by the increase of effective stress caused by piezometric depletion. In this work a Remote Sensing Technique called Coherent Pixel (CPT) is applied to monitor subsidence in the Vega Media of the Segura River during a period of eleven years.

Subsidence activity maps derived from DInSAR data: Orihuela case study

A new methodology is proposed to produce subsidence activity maps based on the geostatistical analysis of persistent scatterer interferometry (PSI) data. PSI displacement measurements are interpolated based on conditional Sequential Gaussian Simulation (SGS) to calculate multiple equiprobable realizations of subsidence. The result from this process is a series of interpolated subsidence values, with an estimation of the spatial variability and a confidence level on the interpolation. These maps complement the PSI displacement map, improving the identification of wide subsiding areas at a regional scale. At a local scale, they can be used to identify buildings susceptible to suffer subsidence related damages. In order to do so, it is necessary to calculate the maximum differential settlement and the maximum angular distortion for each building of the study area. Based on PSI-derived parameters those buildings in which the serviceability limit state has been exceeded, and where in situ forensic analysis should be made, can be automatically identified. This methodology has been tested in the city of Orihuela (SE Spain) for the study of historical buildings damaged during the last two decades by subsidence due to aquifer overexploitation. The qualitative evaluation of the results from the methodology carried out in buildings where damages have been reported shows a success rate of 100%.

Twenty-year advanced DInSAR analysis of severe land subsidence: The Alto Guadalentín Basin (Spain) case study

A twenty-year period of severe land subsidence evolution in the Alto Guadalentín Basin (southeast Spain) is monitored using multi-sensor SAR images, processed by advanced differential interferometric synthetic aperture radar (DInSAR) techniques. The SAR images used in this study consist of four datasets acquired by ERS-1/2, ENVISAT, ALOS and COSMO-SkyMed satellites between 1992 and 2012. The integration of ground surface displacement maps retrieved for different time periods allows us to quantify up to 2.50 m of cumulated displacements that occurred between 1992 and 2012 in the Alto Guadalentín Basin. DInSAR results were locally compared with global positioning system (GPS) data available for two continuous stations located in the study area, demonstrating the high consistency of local vertical motion measurements between the two different surveying techniques. An average absolute error of 4.6 ± 4 mm for the ALOS data and of 4.8 ± 3.5 mm for the COSMO-SkyMed data confirmed the reliability of the analysis. The spatial analysis of DInSAR ground surface displacement reveals a direct correlation with the thickness of the compressible alluvial deposits. Detected ground subsidence in the past 20 years is most likely a consequence of a 100–200 m groundwater level drop that has persisted since the 1970s due to the overexploitation of the Alto Guadalentín aquifer system. The negative gradient of the pore pressure is responsible for the extremely slow consolidation of a very thick (> 100 m) layer of fine-grained silt and clay layers with low vertical hydraulic permeability (approximately 50 mm/h) wherein the maximum settlement has still not been reached.

Application of multi-sensor advanced DInSAR analysis to severe land subsidence recognition: Alto Guadalentín Basin (Spain)

Multi-sensor advanced DInSAR analyses have been performed and compared with two GPS station measurements, in order to evaluate the land subsidence evolution in a 20-year period, in the Alto Guadalentín Basin where the highest rate of man-induced subsidence (> 10 cm yr−1) of Europe had been detected. The control mechanisms have been examined comparing the advanced DInSAR data with conditioning and triggering factors (i.e. isobaths of Plio-Quaternary deposits, soft soil thickness and piezometric level).

Mapping surface deformation in open pit iron mines of Carajas Province (Amazon Region) using an integrated SAR analysis

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Finite element models of coseismic deformation due to the 2009 L'Aquila (Italy) and 2008 Wenchuan(China) earthquakes

The topic of my Ph.D. thesis is the finite element modeling of coseismic deformation imaged by DInSAR and GPS data. I developed a method to calculate synthetic Green functions with finite element models (FEMs) and then use linear inversion methods to determine the slip distribution on the fault plane. The method is applied to the 2009 L’Aquila Earthquake (Italy) and to the 2008 Wenchuan earthquake (China). I focus on the influence of rheological features of the earth's crust by implementing seismic tomographic data and the influence of topography by implementing Digital Elevation Models (DEM) layers on the FEMs. Results for the L’Aquila earthquake highlight the non-negligible influence of the medium structure: homogeneous and heterogeneous models show discrepancies up to 20% in the fault slip distribution values. Furthermore, in the heterogeneous models a new area of slip appears above the hypocenter. Regarding the 2008 Wenchuan earthquake, the very steep topographic relief of Longmen Shan Range is implemented in my FE model. A large number of DEM layers corresponding to East China is used to achieve the complete coverage of the FE model. My objective was to explore the influence of the topography on the retrieved coseismic slip distribution. The inversion results reveals significant differences between the flat and topographic model. Thus, the flat models frequently adopted are inappropriate to represent the earth surface topographic features and especially in the case of the 2008 Wenchuan earthquake.

InSAR deformation measurements of the earthquake cycle in transcurrent tectonic domains, analytical and analog modeling

I applied the SBAS-DInSAR method to the Mattinata Fault (MF) (Southern Italy) and to the Doruneh Fault System (DFS) (Central Iran). In the first case, I observed limited internal deformation and determined the right lateral kinematic pattern with a compressional pattern in the northern sector of the fault. Using the Okada model I inverted the observed velocities defining a right lateral strike slip solution for the MF. Even if it fits the data within the uncertainties, the modeled slip rate of 13-15 mm yr-1 seems too high with respect to the geological record. Concerning the Western termination of DFS, SAR data confirms the main left lateral transcurrent kinematics of this fault segment, but reveal a compressional component. My analytical model fits successfully the observed data and quantifies the slip in ~4 mm yr-1 and ~2.5 mm yr-1 of pure horizontal and vertical displacement respectively. The horizontal velocity is compatible with geological record. I applied classic SAR interferometry to the October–December 2008 Balochistan (Central Pakistan) seismic swarm; I discerned the different contributions of the three Mw > 5.7 earthquakes determining fault positions, lengths, widths, depths and slip distributions, constraining the other source parameters using different Global CMT solutions. A well constrained solution has been obtained for the 09/12/2008 aftershock, whereas I tested two possible fault solutions for the 28-29/10/08 mainshocks. It is not possible to favor one of the solutions without independent constraints derived from geological data. Finally I approached the study of the earthquake-cycle in transcurrent tectonic domains using analog modeling, with alimentary gelatins like crust analog material. I successfully joined the study of finite deformation with the earthquake cycle study and sudden dislocation. A lot of seismic cycles were reproduced in which a characteristic earthquake is recognizable in terms of displacement, coseismic velocity and recurrence time.

Diseño de un sistema de auscultación de subsidencias mediante técnicas geomáticas

La subsidencia del terreno constituye un riesgo geotécnico capaz de afectar a amplias zonas del territorio. Este fenómeno puede producirse por la consolidación de los suelos finos de un sistema acuífero, disolución y colapso de materiales yesíferos, actuaciones humanes, etc. Muchas regiones del mundo, y gran parte de la geografía peninsular, pueden verse afectadas de manera significativa por este fenómeno. En este proyecto se pretende crear una metodología de trabajo que se pueda aplicar en cualquier ámbito geográfico para el control de las subsidencias. Para la realización de esta metodología se han tomado tres técnicas de auscultación de subsidencias, nivelación geométrica de precisión, nivelación GPS y DinSAR, y comparado sus pros y contras, así como las precisiones esperadas y el organigrama de trabajo. Para que se vea mejor la funcionalidad del sistema, se ha procedido a la implantación teórica del mismo en una localización al Norte de la ciudad de Madrid con un escenario realista. Abstract Subsidence is a geotechnical risk which can affect large countryside areas. This phenomenon may be produced by the consolidation of an aquifer system fine soils, dissolution and collapse of gypsum materials, human actions, etc. Many regions of the world, and much of the Iberian Peninsula, may be significantly affected by this condition. This project aims to create a methodology that can be applied in any geographical area to control subsidence. For this purpose, three subsidence monitoring techniques have been studied. Those are precision geometric leveling, GPS leveling and DInSAR. During the project, pros and cons as well as the precisions expected and work schedule have been studied and compared. The subsidence auscultation system has been theoretically implemented in a location. This location is a realistic stage located north of Madrid

Performance of TerraSAR-X for urban subsidence monitoring: Murcia case study

This paper presents an analysis of the performance of TerraSAR-X for subsidence monitoring in urban areas. The city of Murcia has been selected as a test-site due to its high deformation rate and the set of extensometers deployed along the city that provide validation data. The obtained results have been compared with those obtained from ERS/ENVISAT data belonging to the same period and validated with the in-situ measurements.

Forensic analysis of buildings affected by mining subsidence based on Differential Interferometry (Part III)

This work presents a forensic analysis of buildings affected by mining subsidence, which is based on deformation data obtained by Differential Interferometry (DInSAR). The proposed test site is La Union village (Murcia, SE Spain) where subsidence was triggered in an industrial area due to the collapse of abandoned underground mining labours occurred in 1998. In the first part of this work the study area was introduced, describing the spatial and temporal evolution of ground subsidence, through the elaboration of a cracks map on the buildings located within the affected area. In the second part, the evolution of the most significant cracks found in the most damaged buildings was monitored using biaxial extensometric units and inclinometers. This article describes the work performed in the third part, where DInSAR processing of satellite radar data, available between 1998 and 2008, has permitted to determine the spatial and temporal evolution of the deformation of all the buildings of the study area in a period when no continuous in situ instrumental data is available. Additionally, the comparison of these results with the forensic data gathered in the 2005–2008 period, reveal that there is a coincidence between damaged buildings, buildings where extensometers register significant movements of cracks, and buildings deformation estimated from radar data. As a result, it has been demonstrated that the integration of DInSAR data into forensic analysis methodologies contributes to improve significantly the assessment of the damages of buildings affected by mining subsidence.