The Behavior of Demineralized Bone Matrix (DBM) in Post-Extraction Sockets

Autogenous bone grafts are considered to be the gold standard in bone regeneration because of their osteogenic activity; however, due to limited availability of intraoral donor sites and the need to resolve the demands of patients requires an alternative to these. Two male patients were submitted to implant surgery in two stages with 6 months intervals between each of them: the first was exodontia and placement of DBM graft into the socket; the second stage was the drill with a 2 mm internal diameter trephine in center of the alveolar ridge previously grafted with DBM and subsequent implant placement. The samples were analyzed under histological techniques. A very mature bone was observed at 6 months after DBM graft placement in the sockets, showing it to be a good alternative as bone graft.

Northeast Greenland - Digital Bathymetric Compilation, with links to DBM in ArcGIS format

A new digital bathymetric model (DBM) for the Northeast Greenland (NEG) continental shelf (74°N - 81°N) is presented. The DBM has a grid cell size of 250 m × 250 m and incorporates bathymetric data from 30 multibeam cruises, more than 20 single-beam cruises and first reflector depths from industrial seismic lines. The new DBM substantially improves the bathymetry compared to older models. The DBM not only allows a better delineation of previously known seafloor morphology but, in addition, reveals the presence of previously unmapped morphological features including glacially derived troughs, fjords, grounding-zone wedges, and lateral moraines. These submarine landforms are used to infer the past extent and ice-flow dynamics of the Greenland Ice Sheet during the last full-glacial period of the Quaternary and subsequent ice retreat across the continental shelf. The DBM reveals cross-shelf bathymetric troughs that may enable the inflow of warm Atlantic water masses across the shelf, driving enhanced basal melting of the marine-terminating outlet glaciers draining the ice sheet to the coast in Northeast Greenland. Knolls, sinks, and hummocky seafloor on the middle shelf are also suggested to be related to salt diapirism. North-south-orientated elongate depressions are identified that probably relate to ice-marginal processes in combination with erosion caused by the East Greenland Current. A single guyot-like peak has been discovered and is interpreted to have been produced during a volcanic event approximately 55 Ma ago.

Experience-induced preference for oviposition repellents derived from a non-host plant by a specialist herbivore

Foraging adults of phytophagous insects are attracted by host-plant volatiles and supposedly repelled by volatiles from non-host plants. In behavioural control of pest insects, chemicals derived from non-host plants applied to crops are expected to repel searching adults and thereby reduce egg laying. How experience by searching adults of non-host volatiles affects their subsequent searching and oviposition behaviour has been rarely tested. In laboratory experiments, we examined the effect of experience of a non-host-plant extract on the oviposition behaviour of the diamondback moth (DBM), Plutella xylostella, a specialist herbivore of cruciferous plants. Naive ovipositing DBM females were repelled by an extract of dried leaves of Chrysanthemum morifolium, a non-host plant of DBM, but experienced females were not repelled. Instead they were attracted by host plants treated with the non-host-plant extract and laid a higher proportion of eggs on treated than on untreated host plants. Such behavioural changes induced by experience could lead to host-plant range expansion in phytophagous insects and play an important role in determining outcome for pest management of some behavioural manipulation methods.

Fluoride effects on ectopic bone formation in young and old rats

This study evaluated the effect of fluoride oil bone fluoride levels and on ectopic bone formation in young and old rats. Eighty male Wistar rats were assigned to four groups (n = 20/g), which differed according to the fluoride concentration in their drinking water (0, 5, 15 and 50 mg/l). When half of the rats were 90 days old, demineralized bone matrix (DBM) was implanted. The other rats received DBM implants when they were 365 day`s old. The animals were killed 28 days after. Fluoride in the femur surface, whole femur and plasma was analyzed with an electrode, The implants were analyzed histomorphometrically. Data were tested for statistically, significant differences by ANOVA, Tukey`s test, t-test and linear regression (p < 0.05). Increases in plasma, femur surface and whole femur fluoride concentrations were observed cis water fluoride levels increased. There was also a trend for increase in plasina and femur fluoride concentrations cis age increased. Significant positive correlations were found between plasma and femur surface, plasina and femur and femur surface and femur fluoride, concentrations. The morphometric analyses indicated all increase in bone formation for younger rats that received 5 mg/l of fluoride in the drinking water. However, this was not statistically, significant. The younger rats that received 50 mg/l of fluoride showed impairment in bone formation. Bone formation was not significantly affected among the older rats. The results suggest that lower doses of fluoride in the drinking water, which slightly increase plasma fluoride levels, may have an anabolic effect oil bone formation in younger rats. Copyright 2008 Prous Science, S.A.U. or its licensors. All rights reserved.

Database technologies for l-system simulations in virtual plant applications on bioinformatics

One of the most important advantages of database systems is that the underlying mathematics is rich enough to specify very complex operations with a small number of statements in the database language. This research covers an aspect of biological informatics that is the marriage of information technology and biology, involving the study of real-world phenomena using virtual plants derived from L-systems simulation. L-systems were introduced by Aristid Lindenmayer as a mathematical model of multicellular organisms. Not much consideration has been given to the problem of persistent storage for these simulations. Current procedures for querying data generated by L-systems for scientific experiments, simulations and measurements are also inadequate. To address these problems the research in this paper presents a generic process for data-modeling tools (L-DBM) between L-systems and database systems. This paper shows how L-system productions can be generically and automatically represented in database schemas and how a database can be populated from the L-system strings. This paper further describes the idea of pre-computing recursive structures in the data into derived attributes using compiler generation. A method to allow a correspondence between biologists' terms and compiler-generated terms in a biologist computing environment is supplied. Once the L-DBM gets any specific L-systems productions and its declarations, it can generate the specific schema for both simple correspondence terminology and also complex recursive structure data attributes and relationships.

Variáveis reprodutivas e risco para doenças benignas de mama: estudo caso-controle

Foram estudadas 257 mulheres com diagnóstico de doença benigna de mama (DBM), atestado por anatomopatológico ou citologia, e um controle para cada uma delas. Foram apresentados resultados das possíveis relações entre variáveis reprodutivas e o risco para DBM. Os casos e controles foram comparados levando em conta a idade na menarca e na menopausa, o número de gravidezes, de meses em que amamentaram e de ciclos menstruais ovulatórios, e os antecedentes familiares de câncer de mama. Mostraram influência significativa, em relação às DBM, a nuliparidade, aumentando o risco enquanto a idade de 30 ou mais anos no primeiro parto o reduziu; o número de ciclos ovulatórios, que foi significativamente maior para os casos, e a média de meses de uso de pílula, menor entre as mulheres com DBM. O uso de contraceptivos orais apresentou um efeito protetor apenas quando a duração total do uso foi maior que dois anos. Os resultados não se revelaram novos ou diferentes se comparados com outros estudos, mas confirmam a relativa concordância entre os fatores de risco para DBM e para câncer de mama, ainda que as relações entre esses fatores e as DBM não sejam tão claras como o são para o câncer, e existam também algumas discrepâncias.

Distribuição de sinais rádio e vídeo sobre fibra

As comunicações ópticas e as comunicações sem fios têm sofrido uma grande evolução ao longo das últimas décadas. Com o objectivo de juntar as vantagens de cada um dos sistemas surgiu o que se designa por rádio sobre fibra. Este sistema permite centralizar todo o processamento necessário num só local, na estação central, simplificando assim a estação base. Esta simplificação permite reduzir os custos de implementação e torna o sistema menos complexo. Esta dissertação de mestrado tem como objectivo principal estudar e simular um sistema que permite o envio de sinais vídeo e rádio pela fibra óptica para posterior difusão, utilizando o conceito de rádio sobre fibra. Os sinais enviados foram o LTE (Long Term Evolution), o UWB (Ultra WideBand) e o WiMAX (Worldwide Interoperability for Microwave Access). O primeiro disponibiliza o serviço de voz, o segundo disponibiliza o serviço de televisão e o último dá suporte à internet. Estes sinais foram modulados em OFDM (Orthogonal Frequency Division Multiplex), porque, posteriormente, estes sinais vão ser difundidos num ambiente sem fios e este tipo de modulação minimiza o efeito de multipercurso e da interferência intersimbólica. Com este estudo pretende-se verificar qual a viabilidade de um sistema que permite o envio de três sinais distintos simultaneamente (serviço Triple Play). Ao analisar os resultados deste sistema concluiu-se que a sua aplicabilidade pode apresentar algumas limitações, dependendo do tipo de modulação e do tipo de modulador que se utilize. Os moduladores ópticos utilizados foram o MZ (Mach-Zehnder) e o EA (Electro-Absorption). A qualidade do sinal recebido foi analisada com base no valor de EVM (Error Vector Magnitude). O primeiro modulador foi aquele que apresentou mais limitações, pois o desempenho do sistema é comprometido para distâncias superiores a 40 km e para potências de entrada inferiores a 0 dBm. Este tipo de sistema apresenta um EVM mais baixo quando a potência de entrada utilizada está entre 0 e 6 dBm. Se o modulador utilizado for o EA, o sistema apresenta um EVM mais baixo quando se utiliza um índice de modulação entre 20% e 30%, para uma potência de entrada entre 0 e 2 dBm.

Design and evaluation of multi-band RF energy harvesting circuits and antennas for WSNs

Radio frequency (RF) energy harvesting is an emerging technology that will enable to drive the next generation of wireless sensor networks (WSNs) without the need of using batteries. In this paper, we present RF energy harvesting circuits specifically developed for GSM bands (900/1800) and a wearable dual-band antenna suitable for possible implementation within clothes for body worn applications. Besides, we address the development and experimental characterization of three different prototypes of a five-stage Dickson voltage multiplier (with match impedance circuit) responsible for harvesting the RF energy. Different printed circuit board (PCB) fabrication techniques to produce the prototypes result in different values of conversion efficiency. Therefore, we conclude that if the PCB fabrication is achieved by means of a rigorous control in the photo-positive method and chemical bath procedure applied to the PCB it allows for attaining better values for the conversion efficiency. All three prototypes (1, 2 and 3) can power supply the IRIS sensor node for RF received powers of -4 dBm, -6 dBm and -5 dBm, and conversion efficiencies of 20, 32 and 26%, respectively. © 2014 IEEE.

Design of a low-voltage CMOS RF receiver for energy harvesting sensor node

In this thesis a CMOS low-power and low-voltage RF receiver front-end is presented. The main objective is to design this RF receiver so that it can be powered by a piezoelectric energy harvesting power source, included in a Wireless Sensor Node application. For this type of applications the major requirements are: the low-power and low-voltage operation, the reduced area and cost and the simplicity of the architecture. The system key blocks are the LNA and the mixer, which are studied and optimized with greater detail, achieving a good linearity, a wideband operation and a reduced introduction of noise. A wideband balun LNA with noise and distortion cancelling is designed to work at a 0.6 V supply voltage, in conjunction with a double-balanced passive mixer and subsequent TIA block. The passive mixer operates in current mode, allowing a minimal introduction of voltage noise and a good linearity. The receiver analog front-end has a total voltage conversion gain of 31.5 dB, a 0.1 - 4.3 GHz bandwidth, an IIP3 value of -1.35 dBm, and a noise figure lower than 9 dB. The total power consumption is 1.9 mW and the die area is 305x134.5 m2, using a standard 130 nm CMOS technology.

Switching mode power amplifier for bluetooth applications

Modern fully integrated transceivers architectures, require circuits with low area, low cost, low power, and high efficiency. A key block in modern transceivers is the power amplifier, which is deeply studied in this thesis. First, we study the implementation of a classical Class-A amplifier, describing the basic operation of an RF power amplifier, and analysing the influence of the real models of the reactive components in its operation. Secondly, the Class-E amplifier is deeply studied. The different types of implementations are reviewed and theoretical equations are derived and compared with simulations. There were selected four modes of operation for the Class-E amplifier, in order to perform the implementation of the output stage, and the subsequent comparison of results. This led to the selection of the mode with the best trade-off between efficiency and harmonics distortion, lower power consumption and higher output power. The optimal choice was a parallel circuit containing an inductor with a finite value. To complete the implementation of the PA in switching mode, a driver was implemented. The final block (output stage together with the driver) got 20 % total efficiency (PAE) transmitting 8 dBm output power to a 50 W load with a total harmonic distortion (THD) of 3 % and a total consumption of 28 mW. All implementations are designed using standard 130 nm CMOS technology. The operating frequency is 2.4 GHz and it was considered an 1.2 V DC power supply. The proposed circuit is intended to be used in a Bluetooth transmitter, however, it has a wider range of applications.

Wideband CMOS low noise amplifiers

Modern fully integrated receiver architectures, require inductorless circuits to achieve their potential low area, low cost, and low power. The low noise amplifier (LNA), which is a key block in such receivers, is investigated in this thesis. LNAs can be either narrowband or wideband. Narrowband LNAs use inductors and have very low noise figure, but they occupy a large area and require a technology with RF options to obtain inductors with high Q. Recently, wideband LNAs with noise and distortion cancelling, with passive loads have been proposed, which can have low NF, but have high power consumption. In this thesis the main goal is to obtain a very low area, low power, and low-cost wideband LNA. First, it is investigated a balun LNA with noise and distortion cancelling with active loads to boost the gain and reduce the noise figure (NF). The circuit is based on a conventional balun LNA with noise and distortion cancellation, using the combination of a common-gate (CG) stage and common-source (CS) stage. Simulation and measurements results, with a 130 nm CMOS technology, show that the gain is enhanced by about 3 dB and the NF is reduced by at least 0.5 dB, with a negligible impact on the circuit linearity (IIP3 is about 0 dBm). The total power dissipation is only 4.8 mW, and the active area is less than 50 x 50 m2 . It is also investigated a balun LNA in which the gain is boosted by using a double feedback structure.We propose to replace the load resistors by active loads, which can be used to implement local feedback loops (in the CG and CS stages). This will boost the gain and reduce the noise figure (NF). Simulation results, with the same 130 nm CMOS technology as above, show that the gain is 24 dB and NF is less than 2.7 dB. The total power dissipation is only 5.4 mW (since no extra blocks are required), leading to a figure-of-merit (FoM) of 3.8 mW

Deformationsbasierte Morphometrie : eine Methode zur Analyse hirnstruktureller Veränderungen

DBM, schizophrenia, morphometry, computational neuroanatomy