Tailoring microstructure and physical properties of poly(vinylidene fluoride–hexafluoropropylene) porous films

This paper presents a systematic study for the production of poly(vinylidene fluoride-hexafluoropropylene), P(VDF-HFP), porous films using solvent evaporation (SE) and non-solvent induced phase separation (NIPS) techniques. Parameters such as volume fraction of the copolymer solution, film thickness, time exposure to air, non-solvent and temperature of the coagulation bath were investigated on the morphology, crystallization and mechanical properties of the samples. Films with different porous morphologies including homogeneous pore sizes, macrovoids and spherulites were obtained depending on the processing conditions, which in turn affect the wettability and mechanical properties of the material. Knowing that the phase content of the films also depends on the processing conditions, this paper shows that P(VDF-HFP) films with tailored porous morphology, electroactive phase content, hydrophobicity, cristallinity and mechanical properties can be achieved for a specific application using the adequate SE and NIPS techniques conditions.

Aplicação de celulases e xilanases na reciclagem de fibras de papel

Tese de Doutoramento em Engenharia Química e Biológica (área de conhecimento em Engenharia Enzimática e das Fermentações)

Processamento e caracterização da blenda poli (metacrilato de metila) (PMMA) elastomerico e poli (tereftalato de etileno) (PET) pós-consumo

This work studied the immiscible blend of elastomeric poly(methyl methacrylate) (PMMA) with poly(ethylene terephthalate) (PET) bottle grade with and without the use of compatibilizer agent, poly(methyl methacrylate-co-glycidyl methacrylate - co-ethyl acrylate) (MGE). The characterizations of torque rheometry, melt flow index measurement (MFI), measuring the density and the degree of cristallinity by pycnometry, tensile testing, method of work essential fracture (EWF), scanning electron microscopy (SEM) and transmission electron microscopy (TEM) were performed in pure polymer and blends PMMA/PET. The rheological results showed evidence of signs of chemical reaction between the epoxy group MGE with the end groups of the PET chains and also to the elastomeric phase of PMMA. The increase in the concentration of PET reduced torque and adding MGE increased the torque of the blend of PMMA/PET. The results of the MFI also show that elastomeric PMMA showed lower flow and thus higher viscosity than PET. In the results of picnometry observed that increasing the percentage of PET resulted in an increase in density and degree crystallinity of the blends PMMA/PET. The tensile test showed that increasing the percentage of PET resulted in an increase in ultimate strength and elastic modulus and decrease in elongation at break. However, in the phase inversion, where the blend showed evidence of a co-continuous morphology and also, with 30% PET dispersed phase and compatibilized with 5% MGE, there were significant results elongation at break compared to elastomeric PMMA. The applicability of the method of essential work of fracture was shown to be possible for most formulations. And it was observed that with increasing elastomeric PMMA in the formulations of the blends there was an improvement in specific amounts of essential work of fracture (We) and a decrease in the values of specific non-essential work of fracture (βWp)

Variabilidade espacial de atributos mineralógicos de um latossolo sob diferentes formas do relevo: I - mineralogia da fração argila

A distribuição dos minerais da fração argila depende de condições pedoambientais específicas. O estudo das relações entre atributos desses minerais e locais específicos de sua ocorrência na paisagem torna-se importante para o entendimento das relações entre a mineralogia e os demais atributos do solo. Este trabalho teve como objetivo avaliar os atributos cristalográficos, as razões Gt/(Gt+Hm) e Ct/(Ct+Gb) dos minerais da fração argila (hematita, goethita, caulinita e gibbsita) e o padrão de distribuição espacial destes em um Latossolo Vermelho eutroférrico sob cultivo de cana-de-açúcar há mais de 30 anos, com colheita no sistema cana crua. As amostras de solo foram coletadas nos pontos de cruzamento de uma malha, georreferenciados, com intervalos regulares de 10 m, e dimensão de 100 x 100 m, na profundidade de 0,2-0,4 m, totalizando 119 pontos, em uma área de 1 ha. As amostras de solos foram analisadas quimicamente. Posteriormente, a fração argila foi submetida à difração de raios X. Foram feitas as análises estatísticas e geoestatísticas dos atributos cristalográficos dos minerais analisados. Mapas de krigagem foram realizados para a visualização da variabilidade espacial dos atributos. Todos os atributos estudados apresentaram dependência espacial, e os atributos mineralógicos apresentaram-se relacionados com variações das formas do relevo. A gibbsita apresentou o maior diâmetro médio do cristal (DMC) entre os minerais da fração argila estudados, e a goethita foi o mineral que apresentou a maior variação do DMC e da largura à meia altura. Os maiores valores do DMC da goethita, hematita e gibbsita foram encontrados no compartimento II, caracterizado por uma área côncavo-convexa.

Effect of partial crystallization on the mechanical properties and cytotoxicity of bioactive glass from the 3CaO center dot P2O5-SiO2-MgO system

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Características estruturais e físico-químicas de amidos de mandioquinha-salsa (Arracacia xanthorrhiza)

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Efeito do tamanho dos grânulos nas características estruturais e físico-químicas do amido de trigo

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Estudo da hidrólise enzimática do amido de mandioquinha-salsa (Arracacia xanthorrhiza): efeito do tamanho dos grânulos

Pós-graduação em Engenharia e Ciência de Alimentos - IBILCE

Obtenção e caracterização de filmes de PHB utilizando a técnica de solution blow spinning

Pós-graduação em Ciência dos Materiais - FEIS

Síntese de nanofios de óxidos semicondutores para aplicações em dispositivos ópticos e eletrônicos

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Caracterização estrutural de pós de 'SRTIO IND.3' puro e dopado com samário

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Síntese e caracterização de complexos de lantanídeos pesados e ítrio(III) como o fármaco ibuprofeno no estado sólido

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Processamento e caracterização da blenda poli (metacrilato de metila) (PMMA) elastomerico e poli (tereftalato de etileno) (PET) pós-consumo

This work studied the immiscible blend of elastomeric poly(methyl methacrylate) (PMMA) with poly(ethylene terephthalate) (PET) bottle grade with and without the use of compatibilizer agent, poly(methyl methacrylate-co-glycidyl methacrylate - co-ethyl acrylate) (MGE). The characterizations of torque rheometry, melt flow index measurement (MFI), measuring the density and the degree of cristallinity by pycnometry, tensile testing, method of work essential fracture (EWF), scanning electron microscopy (SEM) and transmission electron microscopy (TEM) were performed in pure polymer and blends PMMA/PET. The rheological results showed evidence of signs of chemical reaction between the epoxy group MGE with the end groups of the PET chains and also to the elastomeric phase of PMMA. The increase in the concentration of PET reduced torque and adding MGE increased the torque of the blend of PMMA/PET. The results of the MFI also show that elastomeric PMMA showed lower flow and thus higher viscosity than PET. In the results of picnometry observed that increasing the percentage of PET resulted in an increase in density and degree crystallinity of the blends PMMA/PET. The tensile test showed that increasing the percentage of PET resulted in an increase in ultimate strength and elastic modulus and decrease in elongation at break. However, in the phase inversion, where the blend showed evidence of a co-continuous morphology and also, with 30% PET dispersed phase and compatibilized with 5% MGE, there were significant results elongation at break compared to elastomeric PMMA. The applicability of the method of essential work of fracture was shown to be possible for most formulations. And it was observed that with increasing elastomeric PMMA in the formulations of the blends there was an improvement in specific amounts of essential work of fracture (We) and a decrease in the values of specific non-essential work of fracture (βWp)