Step by step analyses of Clarke's matrix correction procedure for untransposed three-phase transmission line cases

The correction procedure for Clarke's matrix, considering three-phase transmission line analyzes, is analyzed step by step in this paper, searching to improve the application of this procedure. Changing the eigenvectors as modal transformation matrices, Clarke's matrix has been applied to analyses for transposed and untransposed three-phase transmission line cases. It is based on the fact that Clarke's matrix is an eigenvector matrix for transposed three-phase transmission lines considering symmetrical and asymmetrical cases. Because of this, the application of this matrix has been analyzed considering untransposed three-phase transmission lines. In most of these cases, the errors related to the eigenvalues can be considered negligible. It is not true when it is analyzed the elements that are not in main diagonal of the quasi-mode matrix. This matrix is obtained from the application of Clarke's matrix. The quasi-mode matrix is correspondent to the eigenvalue matrix. Their off-diagonal elements represent couplings among the quasi-modes. So, the off-diagonal quasi-mode element relative values are not negligible when compared to the eigenvalues that correspond to the coupled quasi-modes. Minimizing these relative values, the correction procedure is analyzed in detail, checking some alternatives for the correction procedure application.

Correction procedure applied to a single real transformation matrix -Untransposed three-phase transmission line cases

Clarke's matrix has been used as an eigenvector matrix for transposed three-phase transmission lines and it can be applied as a phase-mode transformation matrix for transposed cases. Considering untransposed three-phase transmission lines, Clarke's matrix is not an exact eigenvector matrix. In this case, the errors related to the diagonal elements of the Z and Y matrices can be considered negligible, if these diagonal elements are compared to the exact elements in domain mode. The mentioned comparisons are performed based on the error and frequency scan analyses. From these analyses and considering untransposed asymmetrical three-phase transmission lines, a correction procedure is determined searching for better results from the Clarke's matrix use as a phase-mode transformation matrix. Using the Clarke's matrix, the relative errors of the eigenvalue matrix elements can be considered negligible and the relative values of the off-diagonal elements are significant. Applying the corrected transformation matrices, the relative values of the off-diagonal elements are decreased. The comparisons among the results of these analyses show that the homopolar mode is more sensitive to the frequency influence than the two other modes related to three-phase lines. © 2006 IEEE.

A physics-based correction model for homogenizing sub-daily temperature series

A new physics-based technique for correcting inhomogeneities present in sub-daily temperature records is proposed. The approach accounts for changes in the sensor-shield characteristics that affect the energy balance dependent on ambient weather conditions (radiation, wind). An empirical model is formulated that reflects the main atmospheric processes and can be used in the correction step of a homogenization procedure. The model accounts for short- and long-wave radiation fluxes (including a snow cover component for albedo calculation) of a measurement system, such as a radiation shield. One part of the flux is further modulated by ventilation. The model requires only cloud cover and wind speed for each day, but detailed site-specific information is necessary. The final model has three free parameters, one of which is a constant offset. The three parameters can be determined, e.g., using the mean offsets for three observation times. The model is developed using the example of the change from the Wild screen to the Stevenson screen in the temperature record of Basel, Switzerland, in 1966. It is evaluated based on parallel measurements of both systems during a sub-period at this location, which were discovered during the writing of this paper. The model can be used in the correction step of homogenization to distribute a known mean step-size to every single measurement, thus providing a reasonable alternative correction procedure for high-resolution historical climate series. It also constitutes an error model, which may be applied, e.g., in data assimilation approaches.

The geometric correction and registration of airborne line-scanned imagery for temporal thermal studies

This thesis begins by providing a review of techniques for interpreting the thermal response at the earth's surface acquired using remote sensing technology. Historic limitations in the precision with which imagery acquired from airborne platforms can be geometrically corrected and co-registered has meant that relatively little work has been carried out examining the diurnal variation of surface temperature over wide regions. Although emerging remote sensing systems provide the potential to register temporal image data within satisfactory levels of accuracy, this technology is still not widely available and does not address the issue of historic data sets which cannot be rectified using conventional parametric approaches. In overcoming these problems, the second part of this thesis describes the development of an alternative approach for rectifying airborne line-scanned imagery. The underlying assumption that scan lines within the imagery are straight greatly reduces the number of ground control points required to describe the image geometry. Furthermore, the use of pattern matching procedures to identify geometric disparities between raw line-scanned imagery and corresponding aerial photography enables the correction procedure to be almost fully automated. By reconstructing the raw image data on a truly line-by-line basis, it is possible to register the airborne line-scanned imagery to the aerial photography with an average accuracy of better than one pixel. Providing corresponding aerial photography is available, this approach can be applied in the absence of platform altitude information allowing multi-temporal data sets to be corrected and registered.

Monte Carlo Simulation Of The Response Functions Of Cdte Detectors To Be Applied In X-ray Spectroscopy.

In this work, the energy response functions of a CdTe detector were obtained by Monte Carlo (MC) simulation in the energy range from 5 to 160keV, using the PENELOPE code. In the response calculations the carrier transport features and the detector resolution were included. The computed energy response function was validated through comparison with experimental results obtained with (241)Am and (152)Eu sources. In order to investigate the influence of the correction by the detector response at diagnostic energy range, x-ray spectra were measured using a CdTe detector (model XR-100T, Amptek), and then corrected by the energy response of the detector using the stripping procedure. Results showed that the CdTe exhibits good energy response at low energies (below 40keV), showing only small distortions on the measured spectra. For energies below about 80keV, the contribution of the escape of Cd- and Te-K x-rays produce significant distortions on the measured x-ray spectra. For higher energies, the most important correction is the detector efficiency and the carrier trapping effects. The results showed that, after correction by the energy response, the measured spectra are in good agreement with those provided by a theoretical model of the literature. Finally, our results showed that the detailed knowledge of the response function and a proper correction procedure are fundamental for achieving more accurate spectra from which quality parameters (i.e., half-value layer and homogeneity coefficient) can be determined.

Color constancy and the functional significance of McCollough effects

A central problem in visual perception concerns how humans perceive stable and uniform object colors despite variable lighting conditions (i.e. color constancy). One solution is to 'discount' variations in lighting across object surfaces by encoding color contrasts, and utilize this information to 'fill in' properties of the entire object surface. Implicit in this solution is the caveat that the color contrasts defining object boundaries must be distinguished from the spurious color fringes that occur naturally along luminance-defined edges in the retinal image (i.e. optical chromatic aberration). In the present paper, we propose that the neural machinery underlying color constancy is complemented by an 'error-correction' procedure which compensates for chromatic aberration, and suggest that error-correction may be linked functionally to the experimentally induced illusory colored aftereffects known as McCollough effects (MEs). To test these proposals, we develop a neural network model which incorporates many of the receptive-field (RF) profiles of neurons in primate color vision. The model is composed of two parallel processing streams which encode complementary sets of stimulus features: one stream encodes color contrasts to facilitate filling-in and color constancy; the other stream selectively encodes (spurious) color fringes at luminance boundaries, and learns to inhibit the filling-in of these colors within the first stream. Computer simulations of the model illustrate how complementary color-spatial interactions between error-correction and filling-in operations (a) facilitate color constancy, (b) reveal functional links between color constancy and the ME, and (c) reconcile previously reported anomalies in the local (edge) and global (spreading) properties of the ME. We discuss the broader implications of these findings by considering the complementary functional roles performed by RFs mediating color-spatial interactions in the primate visual system. (C) 2002 Elsevier Science Ltd. All rights reserved.

Percentage of nonoverlapping corrected data

The present study proposes a modification in one of the most frequently applied effect size procedures in single-case data analysis the percent of nonoverlapping data. In contrast to other techniques, the calculus and interpretation of this procedure is straightforward and it can be easily complemented by visual inspection of the graphed data. Although the percent of nonoverlapping data has been found to perform reasonably well in N = 1 data, the magnitude of effect estimates it yields can be distorted by trend and autocorrelation. Therefore, the data correction procedure focuses on removing the baseline trend from data prior to estimating the change produced in the behavior due to intervention. A simulation study is carried out in order to compare the original and the modified procedures in several experimental conditions. The results suggest that the new proposal is unaffected by trend and autocorrelation and can be used in case of unstable baselines and sequentially related measurements.

A modified structural stress method for fatigue assessment of welded structures

Fatigue life assessment of weldedstructures is commonly based on the nominal stress method, but more flexible and accurate methods have been introduced. In general, the assessment accuracy is improved as more localized information about the weld is incorporated. The structural hot spot stress method includes the influence of macro geometric effects and structural discontinuities on the design stress but excludes the local features of the weld. In this thesis, the limitations of the structural hot spot stress method are discussed and a modified structural stress method with improved accuracy is developed and verified for selected welded details. The fatigue life of structures in the as-welded state consists mainly of crack growth from pre-existing cracks or defects. Crack growth rate depends on crack geometry and the stress state on the crack face plane. This means that the stress level and shape of the stress distribution in the assumed crack path governs thetotal fatigue life. In many structural details the stress distribution is similar and adequate fatigue life estimates can be obtained just by adjusting the stress level based on a single stress value, i.e., the structural hot spot stress. There are, however, cases for which the structural stress approach is less appropriate because the stress distribution differs significantly from the more common cases. Plate edge attachments and plates on elastic foundations are some examples of structures with this type of stress distribution. The importance of fillet weld size and weld load variation on the stress distribution is another central topic in this thesis. Structural hot spot stress determination is generally based on a procedure that involves extrapolation of plate surface stresses. Other possibilities for determining the structural hot spot stress is to extrapolate stresses through the thickness at the weld toe or to use Dong's method which includes through-thickness extrapolation at some distance from the weld toe. Both of these latter methods are less sensitive to the FE mesh used. Structural stress based on surface extrapolation is sensitive to the extrapolation points selected and to the FE mesh used near these points. Rules for proper meshing, however, are well defined and not difficult to apply. To improve the accuracy of the traditional structural hot spot stress, a multi-linear stress distribution is introduced. The magnitude of the weld toe stress after linearization is dependent on the weld size, weld load and plate thickness. Simple equations have been derived by comparing assessment results based on the local linear stress distribution and LEFM based calculations. The proposed method is called the modified structural stress method (MSHS) since the structural hot spot stress (SHS) value is corrected using information on weld size andweld load. The correction procedure is verified using fatigue test results found in the literature. Also, a test case was conducted comparing the proposed method with other local fatigue assessment methods.

Überwachung der Vorspannkraft Externer Spannglieder mit Hilfe der Modalanalyse

Aufgrund ihrer Vorteile hinsichtlich Dauerhaftigkeit und Bauwerkssicherheit ist in Deutschland seit 1998 die externe Vorspannung in Hohlkastenbrücken zur Regelbauweise geworden. Durch Verwendung der austauschbaren externen Vorspannung verspricht man sich im Brückenbau weitere Verbesserungen der Robustheit und damit eine Verlängerung der Lebensdauer. Trotz des besseren Korrosionsschutzes im Vergleich zur internen Vorspannung mit Verbund sind Schäden nicht völlig auszuschließen. Um die Vorteile der externen Vorspannung zu nutzen, ist daher eine periodische Überwachung der Spanngliedkräfte, z. B. während der Hauptprüfung des Bauwerks, durchzuführen. Für die Überwachung der Spanngliedkräfte bei Schrägseilbrücken haben sich die Schwingungsmessmethoden als wirtschaftlich und leistungsfähig erwiesen. Für die Übertragung der Methode auf den Fall der externen Vorspannung, wo kürzere Schwingungslängen vorliegen, waren zusätzliche Untersuchungen hinsichtlich der effektiven Schwingungslänge, der Randbedingungen sowie der effektiven Biegesteifigkeit erforderlich. Im Rahmen der vorliegenden Arbeit wurde das Modellkorrekturverfahren, basierend auf der iterativen Anpassung eines F.E.-Modells an die identifizierten Eigenfrequenzen und Eigenformen des Spanngliedes, für die Bestimmung der Spanngliedkräfte verwendet. Dieses Verfahren ermöglicht die Berücksichtigung der Parameter (Schwingungslänge, Randbedingungen und effektive Biegesteifigkeit) bei der Identifikation der effektiven Spanngliedkräfte. Weiterhin ist eine Modellierung jeder beliebigen Spanngliedausbildung, z. B. bei unterschiedlichen Querschnitten in den Verankerungs- bzw. Umlenkbereichen, gewährleistet. Zur Anwendung bei der Ermittlung der Spanngliedkräfte wurde eine spezielle Methode, basierend auf den besonderen dynamischen Eigenschaften der Spannglieder, entwickelt, bei der die zuvor genannten Parameter innerhalb jedes Iterationsschrittes unabhängig korrigiert werden, was zur Robustheit des Identifikationsverfahrens beiträgt. Das entwickelte Verfahren ist in einem benutzerfreundlichen Programmsystem implementiert worden. Die erzielten Ergebnisse wurden mit dem allgemeinen Identifikationsprogramm UPDATE_g2 verglichen; dabei ist eine sehr gute Übereinstimmung festgestellt worden. Beim selbst entwickelten Verfahren wird die benötigte Rechenzeit auf ca. 30 % reduziert [100 sec à 30 sec]. Es bietet sich daher für die unmittelbare Auswertung vor Ort an. Die Parameteridentifikationsverfahren wurden an den Spanngliedern von insgesamt sechs Brücken (vier unterschiedliche Spannverfahren) angewendet. Die Anzahl der getesteten Spannglieder beträgt insgesamt 340. Die Abweichung zwischen den durch Schwingungs-messungen identifizierten und gemessenen (bei einer Brücke durch eine Abhebekontrolle) bzw. aufgebrachten Spanngliedkräften war kleiner als 3 %. Ferner wurden die Auswirkungen äußerer Einflüsse infolge Temperaturschwankungen und Verkehr bei den durchgeführten Messungen untersucht. Bei der praktischen Anwendung sind Besonderheiten aufgetreten, die durch die Verwendung des Modellkorrekturverfahrens weitgehend erfasst werden konnten. Zusammenfassend lässt sich sagen, dass die Verwendung dieses Verfahrens die Genauigkeit im Vergleich mit den bisherigen Schwingungsmessmethoden beachtlich erhöht. Ferner wird eine Erweiterung des Anwendungsbereiches auch auf Spezialfälle (z. B. bei einem unplanmäßigen Anliegen) gewährleistet.

Proposal of an alternative transmission line model for symmetrical and asymmetrical configurations

This article shows a transmission line model for simulation of fast and slow transients, applied to symmetrical or asymmetrical configurations. A transmission line model is developed based on lumped elements representation and state-space techniques. The proposed methodology represents a practical procedure to model three-phase transmission lines directly in time domain, without the explicit or implicit use of inverse transforms. In three-phase representation, analysis modal techniques are applied to decouple the phases in their respective propagation modes, using a correction procedure to set a real and constant matrix for untransposed lines with or without vertical symmetry plane. The proposed methodology takes into account the frequency-dependent parameters of the line and in order to include this effect in the state matrices, a fitting procedure is applied. To verify the accuracy of the proposed state-space model in frequency domain, a simple methodology is described based on line distributed parameters and transfer function associated with input/output signals of the lumped parameters representation. In addition, this article proposes the use of a fast and robust integration procedure to solve the state equations, enabling transient and steady-state simulations. The results obtained by the proposed methodology are compared with several established transmission line models in EMTP, taking into account an asymmetrical three-phase transmission line. The principal contribution of the proposed methodology is to handle a steady fundamental signal mixed with fast and slow transients, including impulsive and oscillatory behavior, by a practical procedure applied directly in time domain for symmetrical or asymmetrical representations. (C) 2011 Elsevier Ltd. All rights reserved.

Time Domain Analyses for Three-phase Lines with Corrected Modal Transformation Matrix

The results presented in this paper are based on a research about the application of approximated transformation matrices for electromagnetic transient analyses and simulations in transmission lines. Initially, it has developed the application of a single real transformation matrix for a double three-phase transmission lines, because the symmetry of the distribution of the phase conductors and the ground wires. After this, the same type of transformation matrix has applied for symmetrical single three-phase transmission lines. Analyzing asymmetrical single three-phase lines, it has used three different line configurations. For these transmission line types, the errors between the eigenvalues and the approximated results, called quasi modes, have been considered negligible. on the other hand, the quasi mode eigenvalue matrix for each case was not a diagonal one. and the relative values of the off-diagonal elements of the approximated quasi mode matrix are not negligible, mainly for the low frequencies. Based on this problem, a correction procedure has been applied for minimizing the mentioned relative values. For the correction procedure application, symmetrical and asymmetrical single three-phase transmission line samples have been used. Checking the correction procedure results, analyses and simulations have been carried out in mode and time domain. In this paper, the last results of mentioned research are presented and they related to the time domain simulations.

Modal transformation obtained from Clarke's matrix - Asymmetrical three-phase case

Some constant matrices can be used as phase-mode transformation matrices for transposed three-phase transmission lines. Clarke's matrix is one of these options. Its application as a phase-mode transformation matrix for untransposed three-phase transmission lines has been analyzed through error and frequency scan comparisons. Based on an actual untransposed asymmetrical three-phase transmission line example, a correction procedure is applied searching for better results from the Clarke's matrix applicaton as a phase-mode transformation matrix. The error analyses are carried out using Clarke's matrix and the new transformation matrices obtained from the correction procedure. Applying Clarke's matrix, the relative errors of the eigenvalue matrix elements can be considered negligible and the relative values of the off-diagonal elements are significant. If the the corrected transformation matrices are used, the relative values of the off-diagonal elements are decreased. Based on the results of these analyses, the homopolar mode is more sensitive to the frequency influence than the two other modes related to three-phase lines. © 2007 IEEE.

Digital filtering of oscillations intrinsic to transmission line modeling based on lumped parameters

A correction procedure based on digital signal processing theory is proposed to smooth the numeric oscillations in electromagnetic transient simulation results from transmission line modeling based on an equivalent representation by lumped parameters. The proposed improvement to this well-known line representation is carried out with an Finite Impulse Response (FIR) digital filter used to exclude the high-frequency components associated with the spurious numeric oscillations. To prove the efficacy of this correction method, a well-established frequency-dependent line representation using state equations is modeled with an FIR filter included in the model. The results obtained from the state-space model with and without the FIR filtering are compared with the results simulated by a line model based on distributed parameters and inverse transforms. Finally, the line model integrated with the FIR filtering is also tested and validated based on simulations that include nonlinear and time-variable elements. © 2012 Elsevier Ltd. All rights reserved.

Leitura recombinativa generalizada após procedimentos de correção com fading em pessoas com atraso no desenvolvimento cognitivo

Estudos têm investigado a aplicação de procedimentos de correção, como o ensino de cópia, ditado e oralização na promoção da leitura recombinativa em pessoas com e sem atraso no desenvolvimento cognitivo. A utilização de técnicas de apoio, como o fading, ainda não foram testadas nesses procedimentos como mais uma variável que poderia estar favorecendo de forma imediata, a leitura recombinativa generalizada. A presente pesquisa relata dois estudos. O estudo 1 com duas etapas, tendo como participantes dois alunos com atraso do desenvolvimento cognitivo. Na Etapa A, os alunos foram submetidos ao ensino das relações entre palavras ditadas e palavras impressas (AC) e em seguida, aos testes de equivalência entre figuras e palavras impressas (BC) e palavras impressas e figuras (CB). Após estes testes, foram aplicados os testes de leitura das palavras de ensino (MALA, PATO e BOCA) e das palavras de generalização (formadas a partir da recombinação entre as sílabas das palavras de ensino). Os participantes apresentaram apenas a leitura das palavras de ensino, após ter sido documentado a formação de classes de equivalência entre figuras, palavras ditadas e palavras impressas. Em seguida, foram aplicadas as sondas de controle pelas unidades silábicas, e após essas sondas, aplicou-se um procedimento de correção com destaque das sílabas específicas (sílabas identificadas após a aplicação das sondas de controle pelas unidades silábicas) durante o ensino de combinado de cópia, ditado e oralização. Após quatro exposições ao procedimento de correção, os participantes continuaram a apresentar somente a leitura das palavras de ensino. Na Etapa B, introduziu-se, no procedimento de correção, um fading in nas sílabas específicas. O participante MAR apresentou a leitura correta de todas as palavras de generalização após a segunda aplicação do procedimento de correção e o participante CLA após a terceira aplicação. Os participantes apresentaram a transferência de função para as novas formas verbais AB, AC, BC, CB, AB, AC, BC e CB. Estes resultados indicaram a necessidade de avaliar os dois procedimentos de correção de forma isolada. No Estudo 2, foram selecionados dois participantes com atraso no desenvolvimento cognitivo. Foi aplicado o mesmo delineamento experimental do Estudo 1, sendo que um participante foi submetido ao procedimento de correção e um outro, ao procedimento de correção com fading in. O participante FER foi submetido a procedimento de correção com fading in e o participante JOS ao procedimento de correção com destaque das silabas. Os dois participantes apresentaram a leitura recombinativa generalizada após a condução do procedimento de correção com fading in. Apresentaram ainda a transferência de função para as novas formas verbais AB, AC, BC, CB, AB, AC, BC e CB. Os resultados sugerem que o procedimento com fading in favorece de forma imediata a leitura recombinativa generalizada em pessoas com atraso no desenvolvimento cognitivo.